MANUAL OF REMOTE CONTROL AM Mo Tu We Th Fi Sa Su
CONTENTS A REMOTE CONTROL 1-4 A-1 Install The Battery 2 A-2 Remote Control Parameters B REMOTE CONTROL PROGRAMMING B-1 Enter into setting mode B2-B5 Set the time and timing B6-B13 Pair with the motor and set the limits C CERTIFIED STATEMENT C-1 FCC Statement 3-4 5-18 6 7-10 11-18 19 19
A REMOTE CONTROL Magnetic Holder + Lithuim Cell CR2450 3V sc 3V(CR2450) 1
A-1 INSTALL THE BATTETRY 1 Use a pen to pry the back cover of the remote Slightly press the back cover to prevent it from popping out.
A-2 REMOTE CONTROL PARAMETERS Up Tilt Blinds Tilt Blinds + Channel - Channel AM Mo Week Tu We Th Fi Sa Su Time: 24 hours Fav.
Installation on the wall Back 4
B REMOTE CONTROL PROGRAMMING AM Mo Tu We Th Fi Sa 5 Su
B-1 ENTER INTO SETTING MODE P2 + Lithuim Cell CR2450 3V sc P1 Press and hold "P1" for 5s AM Mo Tu We Th Fi Sa Su The remote lights up and flashes for three times AM Mo Tu We Th Fi Sa Su The channel icon flashes , which means it is in setting mode It will exit setting mode if there is no action for more than 3 minutes 6
B-2 SET THE TIME Please ensure the remote is in setting mode before doing the steps below: 1 Lithuim Cell CR2450 3V sc P2 + P1 Press and hold "P2" for 5s Mo The "hour" icon flashes 2 +Adjust numbers, weeks Select "Hour", "minute", "Week" Select "Hour", "minute", "Week" Mo Save and exit Cancel and exit -Adjust numbers, weeks 7
B-3 SET TIMING You can set at most 25 groups of timing for each remote 1 AM Mo Press and hold " " & " " for 3s 2 Press and hold " " to add new timing 3 Press " " or " " to select the icon. The selected one will be flashing. Press " " or " " to select the numbers. 4 Mo Tu We Th Fi Sa Mo Su Tu We Th Fi Press " " to save and the icon of " " will show up.You can select more than one. Press " " to cancel. The icon of " " will not show up if cancelled. Press " " or " " to select the day of the week.
5 Mo Mo Tu We Th Fi Tu We Th Fi Press " " to save and the icon of " " will show up. Press " " or " " to select the top limit position or bottom limit position. The selected one will be flashing. Press " " to cancel. The icon of " " will not show up if cancelled. 6 Mo Press " " or " " to select the channel number. The selected one will be flashing. Tu We Th Fi Press " " to save and the icon of " " will show up. You can select more than one. Mo Tu We Th Fi Press " " to cancel.
B-4 MODIFY THE GROUP OF TIMINGT 1 AM Mo Mo Tu We Th Fi Press and hold " " & " " for 3s 2 3 Mo Mo Tu We Th Fi Press " " or " " to select the group of timing Tu We Th Fi Press and hold " " to enter in the group of timing and modify. The way to modify can be referred by step 3-7 in B-3(P8-P9).
B-6 HOW TO SET FAVORITE RUNNING POSITION Please ensure the remote is in setting mode before doing the steps below: 1 AM Mo Press " " or " ", choose the channel number 2 AM Press " "&" " Mo The motor responds. Beforing setting the favourite running position, please make sure the top and bottom limit positions are already set.
B-7 HOW TO CHANGE UP/DOWN DIRECTION Please ensure the remote is in setting mode before doing the steps below: 1 AM Mo Press " " or " ", choose the channel number 2 Press " "&" AM Mo The motor responds.
B-8 HOW TO ADJUST SHADES RUNNING SPEED Please ensure the remote is in setting mode before doing the steps below: 1 Press " " or " ", choose the channel number AM Mo 2 Speed up The motor responds. AM Mo Press " 2 "&" " Slow down The motor responds.
B-9 HOW TO DELETE THE LIMIT POSITION Please ensure the remote is in setting mode before doing the steps below: 1 AM Mo Press " " or " ", choose the channel number 2 AM Mo Press " "&" " The motor responds.
B-10 HOW TO SET THE LIMIT POSITION Please ensure the remote is in setting mode before doing the steps below: 1 AM Mo Press " " or " ", choose the channel number 2 The motor responds. AM Mo Press " "&" " 3 The motor responds.
B-11 HOW TO REMOVE ONE CHANNEL Please ensure the remote is in setting mode before doing the steps below: 1 Press " " or " ", choose the channel number AM Mo 2 AM AM Mo Mo Press " "&" The light goes out. " The motor responds. All the paired remotes will not be able to control the motor.
B-12 HOW TO RE-PAIR WITH MOTOR Please ensure the remote is in setting mode before doing the steps below: 1 Press " " or " ", choose the channel number AM Mo 2 + Lithuim Cell CR2450 3V sc AM P2 P1 Press "P2" x2 Mo It shows "H2" on the screen. 3 Lithuim Cell CR2450 3V sc P2 + P1 Press "P1" x1 AM Mo It shows "AA" on the screen.
C CERTIFIED STATEMENT C-1 FCC STATEMENT FCC ID: 2A9IAST-15-01 Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and. (2) This device must accept any interference received, including interference that may cause undesired operation.