Vehicle wireless backup camera system Product Manual / Installation Instructions Please read this manual thoroughly before operating the device ,and keep it for future reference .
1. Certificate The system were Certificated by: CE & FCC & EMC & RoHs & Waterproof 2.
. We recommend installing this system on Cars,Pickups, SUVs, Campers, Small RVs, Small Trucks, etc under 35 feet. If only used for reversing, it can be installed on vehicle under 40 ft. But the wireless system may have different performance when meeting different vehicles. If you meet any signal issue, please contact us as soon as possible.
If your vehicle is too large or you meet signals issue, please contact us immediately ,we would solve it for you . 4 . PLEASE READING BELOW INFORMATION BEFORE INSTALLATION : I . Please noted below data of power supply input to the monitor and camera.
Monitor: Voltage range 12V-24V Camera: Voltage range 12V-24V Note : To ensure the service life of the camera, please keep the voltage below 24V ( the camera may be damaged after a period of use if not ). II. Please test the monitor and camera before installation . After you receive the system, you must test the device before installation. Please reference the way below image showed. (1) Plug power cords to the monitor and merged the power wires to camera ,red-red, black-black.
5 . Installation Video and Signal Repairing . I. Wires Connection Please pay attention to the positive and negative poles of the wire. If the positive and negative poles are reversed, it may cause no picture. If the monitor is emitting smoke, please turn off the power immediately and contact customer support. (1) The monitor can be powered by a cigarette lighter. (2) If you just need the system used for back-up, please connect the camera to back-up light/reverse light.
Warm Tips : If there is no image after you install : (i) Please check connections of power source. (Check if the camera and monitor are powered on) (ii) Or if you reverse the positive wire and negative wire are connected correctly. (For example: The backup light black is positive, green is negative ,please don’t backward them.) If you cannot verify which wire is positive, you can connect the black wire to ground (metal part on vehicle), then to test the positive wire, which will protect the camera.
II . Please watch below video on YouTube to help you install the system. https://youtu.be/NPwhlIiNFu4 Scan the QR code through your cellphone browser, such as Google to get the video . If you cannot open this link, it may be caused by the wrong type of software. So you can search the video ID: NPwhlIiNFu4 on www.youtube.com Please contact us with the Email, and we will provide you a link. III . Signal pairing .
Pairing Steps: Note: You don’t need to pair signals if there are images on screen. You only need to pair if no images or after you received a new second camera pair to the current monitor. Step 1 : Make sure the camera and monitor are powered . Step 2 : Presses the “Menu'' button of the monitor into menu mode until the “ Pair ''appear on the monitor ,then press the ''+'' button to pair the signal . Step 3 : Just wait for the image appearing . 6 . 5 Inch Monitor Details & Installation I .
II . The monitor can be attached to the dash or windshield depends on your preference.
III .
upside down(Vertical flip) i.Function: Single/Split Screen: The default is CAM1. Press the + key once to switch to CAM2, and press the + key twice switch to the split screen. Guide Lines ON/OFF: The default guide line is on. Press the - key once to turn off. ii.Press the menu key once, below picture appears.
Press the menu key twice, below picture appears, and the saturation can be adjusted. Press the Menu key three times, below picture appears, the contrast can be adjusted.
Press the menu key four times,below picture appears. The image can be flipped, normal image / mirror image.
Press the menu key six times,below picture appears, and the guide lines can be moved left and right. Press the menu key seven times,below picture appears with Pair icon. Press the + key to Pair the signals (the signals paired before sent out,you don’t need to pair it again, you only need to pair if there is no images on screen after powered on.
7 . Backup/Front View Camera Details & Installation I . Antenna is Waterproof . You can put the antenna outside or inside the vehicle,it will not effect by the water or rain. But please fix it on a proper position will make the signals transmission powerful,If your vehicle is large, please make the antenna on the good position.
II . The camera is made of waterproof material IP69 Waterproof III . Camera Installation The bracket of the camera can be hidden behind the license plate or on the front.
IV . The T-taps are used for protecting the cord of the reversing back-up light or taillight. Just refer to the below picture, which makes the installation easier.
V Remember to remove the protective film of lens. As for the protective film on screen, you can choose to remove or not 8. Two years quality warranty and life time tech support .Just contact us if any issues you meet. 9 . Don’t forget to contact us get your second backup camera and monitor system kit if you or your families need it .
Thank you ! Troubleshooting 1 After installation, you turn on the monitor and camera power without images, at the same time, the monitor turns on for five seconds and then goes black, which means something wrong with the camera. You need to check that the camera is plugged in correctly. If the camera's power cord is not connected correctly to the headlights, there is no images.
engine, you can be sure that you need to add relay or filter to keep signal stable. 3 If you connect the camera to the headlights, and your headlights are LED, it will not work. Because the LED light cannot provide a constant direct current to the camera, you need to switch to another power source to power the camera. 4 If you meet any problem in the process of operating the product, you can contact us for solution.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.