User's Manual
Table Of Contents
Installation Hardware x 1
1
1
Thank you for choosing the YI Dome Guard
1. What's in the Box
YI Dome Guard
Camera x 1
Camera Wall Mount x 1
User Manual x 1
2.
Getting to Know Your Camera
Lens
Indicator Light
Reset Button
MicroSD Card Slot
Light Sensor
Microphone
Speaker
Speaker
R J45 Network
Cable Interface
Power Interface
Input: DC 5V / 1A
3. General Introduction
a) Power on the Camera
As shown in picture , locate the micro-USB Power Interface
and plug the included micro-USB cable into the camera.
Plug the other end of the micro-USB cable into the included
power adapter. The Indicator Light will turn on to indicate that
the camera has power.
b) Connect Your Camera to the YI Home App
Download and install the YI Home App from the Apple App
Store or Google Play.
You can also scan the QR code of the YI Home App below
and complete the installation.
4. Wall Mounting Diagram (optional)
Tips: The mounting wall should be able to support at least 3 times the
total weight of the bracket and the camera.
Use the installation hardware to install
the wall mount to a flat wall/ceiling.
Install the camera onto the wall mount.
Connect the USB power cable to the
camera and switch it on; the camera
will automatically connect to the last
configured Wi-Fi network.
Secure the mount with the
included installation hardware
lnstall the device
5. PTZ Angle
Activity angle:
Horizontal: 0° ~ -355°, Vertical: up 67° ~ down 17°
Vertical Roll
Up 67°
Down 17°
Horizontal Roll 355°
FCC ID: 2AFIB-YRS3521
IC: 20436-YRS3521
HVIN:V2.0
Note:
！
R35GB V1.0
Pairing a device to the camera via a wired connection is not supported. In
order to use a wired connection, you must pair the device the camera to a
Wi-Fi connection and then switch to a wired connection.
- When switching your new network environment, reset your camera, and
re-follow the connection and pairing procedure.
- If you are pairing the camera via sound waves, increase the volume of
your mobile device and keep it close to the camera.
*We recommend that
you insert an 8-128GB
high-speed microSD
card, otherwise your
camera will not be able
to store or view historical
videos as well as other
important functions.
Ensure that there is a Wi-Fi network available.
c) Adding Your Camera to Your YI Account
After logging into the YI Home App, enter the device selection
interface, and select your camera. The camera will flash red and
then click "I heard waiting to connect", once you hear the
"Waiting for connection" voice prompt.
Point the QR code displayed on your phone towards the camera
lens and wait for the camera to scan the QR code. After the QR
code has been scanned, click "Next" and wait until you hear
"Pairing successful".
You can now start using your camera!
Product Name: YI Dome Guard
Model: YRS. 3521
Wi-Fi Standard: 2.4GHz 802.11b/g/n
Power Consumption: 3.5W (Max)
Input: DC 5V / 1A
Operating Temperature: -10~50℃
FCC Statement：
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment .This equipment should be installed and operated with minimum distance
20cm between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning/ISED RF Exposure Statement
ISED RSS Warning: This device complies with Innovation, Science and Economic
Development Canada licence‐exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this
devicemustacceptanyinterference,includinginterferencethatmaycauseundesired
operationofthedevice.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptibled'encompromettrelefonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimumdistance20cmbetweentheradiator&yourbody.Thistransmittermustnot
beco‐locatedoroperatinginconjunctionwithan
yotherantennaortransmitter.
Le rayonnement de la classe b repecte ISED fixaient un environnement non
contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur
distance
minimaleentre20cmtoncorps.Lanceursounepeuventpascoexistercette
antenneoucapteursavecd’autres.