XR-150/XR-450 Portable Radio Manual * This Service manual is subject to change according to improvement of XR-150/XR-450 Portable Radio without notice.
Table of Contents 1. Features -----------------------------------------2. Components of XR-150/XR-450 Series Radio ---------------------- 3 4 3. Appearance of XR-150/XR-450 Series Radio 4. Basic Operation of XR-150/XR-450 Series Radio 5 6 --------------------------------------- 4.1 Installation and Removing the Antenna ---------------------- 6 4.2 Installation and Removing the Battery ---------------------- 7 --------------------- 7 4.3 Installation and Removing the Belt Clip 4.
1. Feature The XR-150/XR-450 series Radio is developed to be user-friendly and compact design, to have various features and to use at the construction / industrial / public areas for the safety & convenience of users. The followings are the main features of the XR-150/XR-450 Series Radio. 16Groups and 512Channels are selectable.
2. Components of XR-150/XR-450 Series Radio * Components could be changed by buyer request.
3.
Figure 3-2) XR-150/XR-450 Series LCD Indication 4. Basic Operation of XR-150/XR-450 Series Radio Pease read this manual carefully before using XR-150/XR-450 series Radio. This manual contains important information about using Radio. 4.1 Installation and Removing the Antenna To install the antenna, insert the antenna into antenna connector and screw the antenna clockwise. To remove the antenna, screw the antenna counter clockwise.
4.2 Installation and Removing the Battery 4.2.1 Installation of the battery -. To install battery, slide up the battery towards the top of the radio until battery latch is locked. 4.2.2 Removing the Battery -. Slide the battery latch located on the bottom of radio to the open position as shown in Figure 4-2. -. The battery is removed by pressing it against and sliding it towards the bottom of the radio Figure 4-2) Installation and Removing the Battery 4.
4.4 Accessory connector Accessory connector is used to connect external speaker Mic, and headset, etc. Please close the cover when nothing is connected. Figure 4-4) Accessory connector 4.5 Operating XR-150/XR-450 RADIO 4.5.1 ON/OFF/Volume Control Turns the radio on and off and adjusts audio volume level. 4.5.2 PTT Button(Push-To-Talk Button) You can transmit by pressing PTT button. DTMF or 5-Tone ID is transmitted according to Transceiver setting. At this moment, you can’t transmit your voice.
4.5.5 Emergency Button In case of emergency situation, if you press the Emergency button, a siren sound will be heard through the speaker in the Radio and the Radio will transmit the emergency signal to the party through the emergency channel. 4.5.6 Channel Buttons(▼,▲) Channel Buttons(▼,▲) have 3 functions as shown in following. ① Channel buttons(▼,▲) are to change channels. ② Channel buttons(▼,▲) are to select menu at menu mode. ③ Channel buttons(▼,▲) are to change transmission power.
The continuous rapid discharge (for example, when making a short circuit on the ‘+’ terminal of battery by a metal substance) may make a fatal defect and the battery can be exploded. Also, it can cause a fire. 4) Using the correct battery will improve the efficiency and safety. 5.2 The Time of Charging Low battery voltage will make the radio less coverage and also make the performance worse.
Specifications of DC-1000/DC-2000 Charger : • INPUT VOLTAGE : DC+10.5V • BATTERY : XSB-2400 • QUICK CHARGING TIME : • OPERATION TEMPERATURE : 0℃~+50℃ • SIZE : 90(W)x105(D)x37(H)m/m • Charging : 750mA(Fast charging) In 4Hours and half 6. Operating Instructions of XR-150/XR-450 Series Radio 6.1 Power On/Off Turn Power switch clockwise. As soon as power is supplied, the backlight will be turned on.
6.3 Reception Method The user should not press PTT button during the reception. The user can adjust the volume by Volume switch, and during reception, the green LED will be turned on. Depending on conditions of the transmitting radio, 6.4 4 Changing Channels Channel buttons (▼,▲) are to change channels. Press Up button (▲). Then, “beep” sound will be generated and the channel number will be increased. Or press Down button (▼) to decrease the channel.
6.6.2 Priority Scan At the Priority Scan mode, the LCD displays ‘SCAN’ and ‘P-‘ icons. The Radio scans the channel in the sequence of CH1, P, CH2, P, CH3, … at the priority scan mode. During receiving signal through the common channel, the Radio scans the priority channel periodically and if the Radio detects the Priority channel, it starts receiving the channel. During receiving the signal, you can move to the following scan channel by pressing the UP or DOWN button.
1) 1:1 Call at call mode Press the “Enter” button for a long period(about 2seconds) at the general mode in order to enter into the call mode. ① Select your party to call by using the channel button (▲, ▼). If you ( ID : 12345 ) want to call your party(ID : 54321), select him(ID : 54321) by using the channel button (▲,▼) at the call mode. Figure 6-8) ID Selection ② You can call the party (ID : 54321) by pressing the “Enter” button and then, the Radio of your party(ID:54321) displays the ID number "12345".
Figure 6-10) Group Call 3) RESET This Reset function converts the TX/RX with no restriction to the previous Close mode. Press the Monitor button (M) at the call mode. ① The call signal will be transmitted to the party’s Radio with the ID number + “C” tone. ② If the party’s Radio is in the Close channel and after receiving the call with the “C” tone, the call is converted to the “TX/RX with no restriction” mode. 6.
6.11 Programming function The Programming is the function for input of the data such as Frequency/Tone/Scan into the Radio. * Programming Method First, please prepare the Program cable for XR-150/XR-450 Series Radio. ① Press the “P” button of the Radio to turn on. Then, the –Prog- message is displayed. ② Connect the Programming cable to the Ear/Microphone Jack of Radio. ③ By using the PC Program, store the data and after disconnecting the cable, turn off the power and turn on the power again.
6.13 Menu description If pressing the "P" button on the side for 2 seconds, the Radio will be in Menu mode. The Menu mode consists of 9 Menus and you can use your desired Menu after selection. ☞ Caution) After entering into the Menu, if you don’t operate the Menu for more than 8 seconds, the Menu mode will be terminated automatically and it is converted to the Receiving mode. 6.13.1 Compander selection This Compander selection is for On/Off of the Compander.
6.13.3 ID output This is for transmission of your ID and reception of your party’s ID. ID is divided by DTMF and Call ID. Especially the Call ID transmits your ID to the party and also, the party’s ID is displayed on your Radio to use your Radio in convenience and efficiently. ① Choose the "Id ANI" by the channel button and press the " Enter " button. ② After the “d-TON” message comes out, choose the ON(”y")/OFF(“n”) by the channel button and press the “Enter” button.
③ Select On(y) or Off (n) by pressing Channel buttons (▼,▲), and save the selected status by pressing Enter button( ).. ④ Exit Menu mode by pressing Menu Button(P) button. Select “Off”. Then, the “ SCR “ symbol will disappear on the LCD 6.13.5 Set Squelch Squelch sensitivity level is selectable by 5step. By PC Program and menu, it could be set. 1. Enter into Menu mode. 2. Select “SQUELCH” by pressing Channel buttons (▼,▲), and press Enter button( ).
Enter button( ). 4. Exit Menu mode by pressing Menu Button(P) button. Select “Off”. Then, the “ “ symbol will disappear on the LCD. 6.13.7 Set VOX Set VOX is to enable users to make transmission for VOX without pressing PTT button. (This function could be available with Ear Mic [External VOX]). By PC Program and menu, it could be set. 1. Enter into Menu mode. 2. Select “H-FrEE” by pressing Channel buttons (▼,▲), and press Enter button( ). 3.
2. Select “LONE W” by pressing Channel buttons (▼,▲), and press Enter button( ). 3. Select On(y) or Off (n) by pressing Channel buttons (▼,▲), and save the selected status by pressing Enter button( ).. 4. Exit Menu mode by pressing Menu Button (P) button. 6.13.9 Set Repeater If you want to use the XR-150/XR-450 Series Radio as a repeater, you can operate the Repeater by On / Off. The Repeater function should be set up by PC program and if not, at the Menu mode the Repeater set-up is not shown. 1.
7. Precautions 7.1 When using the XR-150/XR-450 Series Radios Don’t remove the antenna from the Radio or don’t transform the antenna or don’t make any change on the antenna. The strong electronic wave to be emitted from the Radio can have an effect on the performance of the Radio and can cause the Radio to have a defect. Don’t use the accessories (such as rechargeable battery, adaptor, external speaker microphone and earphone, etc.
In case of the area that medical equipments are being used, please use the Radio after discussion with the equipment maker or the related doctor. Please don’t use the Radio at the place where computer or the other electric/electronic devices are being used, because the strong electronic wave from the Radio can have an effect on the equipments. 8. Safety Notes Please make sure to read the followings for safe and effective use of the Radio. • Please keep the Radio away at least 1inch from the body.
9. Specification 9.1 XR-150 General Frequency Range VHF: 136 ~ 174 MHz Frequency Stability ±2.5PPM (-30 to +60℃) Programmable Channels 512 Channels/16 Group Channel Spacing Dual Channel Spacing 12.5/25 KHz Dimensions 103mm (H)×52mm (W)×32mm (D) Weight 250g (with Battery pack & Antenna) Power Source DC +7.
9.2 XR-450 General Frequency Range Frequency Stability Programmable Channels Channel Spacing Dimensions Weight Power Source Current Drain (maximum) XR-450 : 400 ~ 512 MHz ±2.5PPM (-30 to +60℃) 512 Channels/16 Group Dual Channel Spacing 12.5/25 KHz 103mm (H)×52mm (W)×32mm (D) 250g (with Battery pack & Antenna) DC +7.
Acknowledging Special Precautions and the FCC Notice Cautions. Modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received. Including interference that may cause undesired operation.
RADIO FREQUENCY ENERGY SAFETY INFORMATION This YEONHWA M TECH transceiver has been tested and complies with the standards listed below, in regards to radio Frequency(RF) energy electromagnetic energy(EME) generated by the transceiver > FCC RF exposure limits for Occupational use only. RF exposure limits adopted by the FCC are generally based on recommendations from the national council on radiation protection and measurement, & the American National National Standards Institute.
product. The use of other than recommended or approved body-worn accessories may result in RF exposure levels which exceed the FCC's occupational /controlled environment RF exposure limits. CAUTION To ensure that your exposure to RF EME is within the FCC limits for occupational use, you must observe and adhere to the above points.