m!ka briefing book 1
Thank you for choosing Yellowtec products. Enjoy m!ka, the most exciting support system for microphones and monitors. m!ka is robust, sleek and flexible. All components are designed to fit with each other and can be combined in multiple ways. Check this Briefing Book to get initial infor mation on how to install and adjust the system.
Briefing Book Content m!ka Mic Arm m!ka Mic Arm TV m!ka Studiolight m!ka MMS PDM Kit m!ka Power Sting m!ka MMS Ceiling Mount m!ka Wall Mount m!ka MMS Monitor Mount m!ka EasyLift m!ka MMS Quick Fix m!ka MMS Cable Clamp m!ka MMS Safety Stop m!ka Bushing m!ka MMS Pole Adapter m!ka Table Clamp m!ka Table Mounts m!ka Wall Mounts m!ka Pad-Dock m!ka Copy Stand Remarks 4 6 12 16 17 18 19 20 22 24 26 27 29 30 31 32 34 36 38 40 3
m!ka Mic Arm „On Air“ RED = High Audio Shield BLU = Low N/C N/C Cut Off ! Audio Shield RED = High 5/8“ BLU = Low BLK = LED Indicator 4 YEL = LED Indicator For RED light connect BLK = 0 V YEL = +12-24VDC For WHITE light connect BLK = +12-24VDC YEL = 0 V or toggle polarity for dual use Remarks
m!ka Mic Arm RED = High Audio Shield BLU = Low Audio Shield RED = High 5/8“ BLU = Low Remarks 5
m!ka Mic Arm TV „On Air“ Audio Shield RED = High Microphone BLU = Low BLK = LED Indicator YEL = LED Indicator 6
m!ka Mic Arm TV „On Air“ Remarks Audio Shield RED = High Microphone N/C Cut Off ! N/C BLU = Low For RED light connect BLK = 0 V YEL = +12-24VDC For WHITE light connect BLK = +12-24VDC YEL = 0 V or toggle polarity for dual use 7
m!ka Mic Arm TV RED = High Microphone BLU = Low 8 Audio Shield
m!ka Mic Arm TV Audio Shield RED = High Microphone BLU = Low Remarks 9
m!ka Mic Arm (all models) Remarks 10
m!ka Mic Arm (all models) Remarks 11
m!ka Studiolight Remarks 12
m!ka Studiolight Remarks 13
m!ka Studiolight Remarks 1. 2.
m!ka Studiolight Remarks 15
m!ka MMS PDM-Kit C Remarks 16
m!ka Power Sting Remarks 17
m!ka MMS Ceiling Mount Remarks 18
m!ka Wall Mount Remarks 19
m!ka MMS Monitor Mount 4 Remarks 3 20
m!ka MMS Monitor Mount Remarks 21
m!ka EasyLift Remarks 22
m!ka EasyLift Remarks 23
m!ka MMS QuickFix Remarks 24
m!ka MMS QuickFix Remarks 25
m!ka MMS Cable Clamp Remarks 26
m!ka MMS Safety Stop STOP Remarks 27
m!ka MMS Monitor Arm (Friction) Remarks 28
m!ka Bushing 22 mm Remarks 29
m!ka MMS Pole Adapter Remarks 3 30
m!ka Table Clamp Remarks 31
m!ka Table Through Mount 32
m!ka Table Top Mount Remarks 33
m!ka Wall Bracket Remarks 34
m!ka System Wall Adapter 3 35
m!ka Pad-Dock Remarks 36
m!ka Pad-Dock min 160mm max 300mm Remarks 37
m!ka Copy Stand Remarks 38
m!ka Copy Stand Remarks 39
m!ka Remarks Declaration of Conformity for m!ka Studiolight: We declare under our sole responsibility that m!ka Studiolight meets the health and safety requirements of the EC Directive for General Product Safety. The device complies with the following standards • EN 60589-1 • EN 62031 • EN 55015 • EN 61000-3-2 • EN 60589-1 • EN 60589-2-4 • EN 62471-2-1 • EN 61547 • EN 61000-3-3 according to the requirements of directives • 2006/95/EG • 2004/108/EG For Yellowtec Thum + Mahr GmbH Heinrich-Hertz-Str.
Page 4, 7 - We suggest using XLR-5 pin connectors for microphone signal and on air light feed on lower end of cable and XLR-3 type connectors for microphone on upper end of cable. - When installing the connector on upper end, cut off the black and yellow wires. They are not connected and do not carry any voltage. - Always make sure to leave adequate cable lengths before you cut the cable to fit. It is not possible to install a new cable loom inside the arm.
m!ka Remarks - Do not pull the knurled screws too tight. They may break and the joints may squeak. Instead re-adjust the screw inside the bottom as in Step 1. - If necessary, use Teflon spray in case of joint squeak. Page 12 - Make sure the bolt at the bottom of your m!ka Studiolight has its black plastic sleeve on. The sleeve is needed to fit smoothly to the various mounting devices. - Make sure that the mounting device has a yellow spacer installed.
hole of 12mm diameter for the PDM Kit. - Use black or silver washer according to your choice, but always use one on both sides of the table top! - If you need to use your own threaded bolt make sure you use M10 metric thread. - The cable organizer clip will help to tidy your wiring. Page 17 - Never use the Power Sting other than with the original m!ka Bushing. Table clamps are not suitable to hold an MMS arm. Use a gripper to fix the Power Sting.
m!ka Remarks Page 22 - Use an Allen key to adjust EasyLift‘s pneumatic spring to your monitor‘s weight. - Use the screwing devices at the rotating joints to adjust the joints. Page 23 - You can deactivate the QuickFix function for security reasons. Turn in the screw next to the release lever in order to disengage its function. Page 24 - The MMS QuickFix adapter is suitable to be used with VESA 75 and VESA 100 fixtures. - Make sure that you use the correct screw size and length.
Page 29 - To secure proper upright positioning of the m!ka Bushing drill a hole with a minimum diameter of 22 mm. - The thread of the bushing is metric; should you ever need to replace the nut make sure you use the correct M20x1,5 thread. - Use an Allen key to fix the MMS Pole Adapter properly. - Use a yellow spacer with the MMS Pole Adapter.
m!ka Remarks Page 37 - An audible „click“ signals that the Pad-Dock is securely locked into position. Page 38 - The cover panel for your m!ka Copy Stand holds and aligns by the integrated magnets. - Make sure the magnets face each other. - Follow cleaning instructions, never use detergents or alcohol. - For daily care use micro fiber cloth supplied with Copy Stand. Page 39 - You can deactivate the QuickFix function for security reasons.
m!ka-BB-V5.0 yellowtec.