USB3.
Package checklist Please Check if the following items are present and in good condition upon opening your package. Contact your vendor if any item is damaged or missing. 1. USB3.1 PCI Express Host Card 2. CD Driver 3. User’s Manual(this document) System Requirement l l l l One available x2,x4,x8 or x16 PCI Express slot.(Recommend PCI Express 2.0) Microsoft Windows 7,8.x and 10 operation system. INTEL Core i processor with 4GB DDR RAM or above.
Hardware Installation Follow the instruction given below to install the PCI Express Card: 1.Turn your computer off and remove the power plug from the plug socket. 2.Remove the cover from the computer case. 3.Remove the metal cover plate on the rear of a free PCI Express slot (e.g.PCIex16). 4.Insert the card into one free PCI Express slot and screw it firmly on the bracket side. Plug SATA Power cable (from PS’s Power Supply) to the add-on card’s SATA port. 5.Place the cover back onto the computer. 6.
Note: 1. In order to output effieient +5VDC power to USB device, be sure to plug SATA power cable (from PS’s power supply) into USB3.1 card’ s SATA power connector. 2. In order to get USB3.1 Super Speed+performance, please use PCI Express Generation2 slot for card installation. Or only get half of the data transfer rate. Unplugging or ejecting a devices without first stopping them can often cause your computer to crash and lose valuable data.
Physical Characteristics PCB Dimension 62.2 x 78.3 mm Bracket Standard 120mm (Low Profile 80mm) Bracket Space 1 Note： To satisfy USB3.1 10Gb/s Superspeed+ highest performance. It adopts the PCIe Gen2/x2 (10Gb/s) interface connector design,User has to plug it into PCIe x16(or x4 above) slot on the mainboard, such as graphics add-on card adopting,Due to expansion slot mechanical limitation, this card not be plugged into PCIe x1 slot. Driver Installation USB3.
Please note that Microsoft USB Hotfix driver has to install separately on Win7 and 2008R2.Due to Microsoft licensed issue,driver package is not included,user can go to Microsoft official website (http://support.microsoft.com/) and search keyword “KB 2581464” to download driver package. Asmedia USB3.1 host controller driver is necessary under Microsoft Windows 7 and Server2008R2 operation system.Please install driver as below steps： (1) Please insert the attached CD into your DVD ROM and Run the “Autorun.
(3)Specify driver installation folder in system and click “Next” to continue Click”Finish” to end of the Driver intalltion steps.
Hardware Verify Click on the “Device manager”tab in the Windows Control panel Start>Control panel >Device Manager Under Win7 and 2008 OS, entry Universal Serial Bus controllers catalog, and “ASMedia XHCI1.1 Controller” shows in the device manager. Under Win10,8.x and 2012 OS ,entry Universal Serial Bus controllers catalog and “ASMedia USB3.0 eXtensible Host Controller-0110(Microsoft)”shows in the device manager.USB3.0 description will be updated at the next Microsoft driver hot-fix.
Driver Uninstall Click on the “Programs and Features” tab in the Windows Control Panel Start>Control Panel> Programs and Features Entry Uninstall or change a program page, and double click “ASMedia USB Host Controller Driver” to process driver uninstallation procedure. Troubleshooting Q1. If card and devices connected to the computer do seem to be working properly, please perform below basic troubleshooting steps: Ans: a. Check that all cables are correct and securely connected. b.
Q2. Computer failed to start after inserting the USB3.1 PCI Express card. Ans:Turn off the computer, remove the USB3.1 PCI Express card,and try to restart the Computer. If the computer starts successfully, it means that the card has not been inserted into the PCI Express slot correctly. Please clean PCI golden finger by rubber firstly, then change another PCI-E slot! Q3. How to deal with there is a yellow exclamation point on controller? Ans:a.
Q 8.How come ASMedia USB3.0 eXtensible Host Controller-0110 (Microsoft) shows in the device manager, instead of USB3.1 description. Ans:USB3.1 card uses Windows in-box driver under Windows 10,8.x and 2012 operation system, and it shows default USB description. Microsoft will fix this issue at the next USB driver update. However user still can distinguish USB3.1 and USB3.0 controller by following descriptions. USB3.1=eXtensible Host Controller Ver 1.1 Controller = 0110 (Microsoft) USB3.
