DECT IP Phone W53P & W53H Quick Start Guide(V83.X) For W60B firmware: 77.83.0.X or later For W53H firmware: 88.83.0.
W53P Package Contents W53H Headset W60B Base Station Ethernet Cable Belt Clip Base Stand USB Charger Cradle Quick Start Guide Rechargeable Battery 2 Power Adapters Handset Protective Case (Optional) Note: Yealink W53P DECT IP phone consists of one W60B base station and one W53H handset.
W60B Package Contents W60B Base Station Base Stand Power Adapter Ethernet Cable Quick Start Guide Assembling the DECT Phone 1. Connect the base station power and the network using Method a or Method b. a. AC Power Option b. PoE (Power Over Ethernet) Option Note • If you choose Method a, use Yealink-supplied power adapter (5V/600mA). A third-party power adapter may damage the base station. • If you choose Method b, you do not need to connect the power adapter.
2b. (Wall-Mount Installation) Attach the base station. MA C SN MAC SN 59m m 59m m 3. Insert the battery into the handset. sn 4. Attach the Belt Clip. 5. (Optional) Mount the charger cradle to the wall.
6. Connect the charger cradle and charge the handset. Note • Use Yealink-supplied power adapter (5V/600mA). A third-party power adapter may damage the handset. • Check the charging status on the top right corner of the LCD screen. Getting Started Shortcut Keys Shortcut keys help you quickly access to frequently used phone features. Describe the default shortcut-keys behaviors: 1 2 1 2 3 5 4 3 4 6 5 6 Access the call history record. Check the line status.
Handset Registration You can register up to 8 handsets to one W60B base station. Each handset can be registered to 4 different base stations. on the When the handset LCD screen prompts “Unregistered!”, long press base station till the registration LED flashes. There are two methods to register a new handset: Easy Registration: 1. Press the Reg soft key on the handset to register quickly. Normal Registration: 1. Press the OK soft key on the handset, and then select Register Handset. 2.
To configure the network parameters for the base station manually: 1. Press the OK key to enter the main menu, and then select Settings->System Settings ->Network (default PIN: 0000)->Basic. 2. Select the desired IP addressing mode from the IP Mode field. 3. Press to select the desired IP addressing mode. 4. Make the desired changes. 5. Press the Save soft key to accept the change. Note: • The IP DECT phone supports either or both IPv4 and IPv6 addressing modes, but IPv6 is disabled by default.
Handset Settings Handset Name To rename the handset: 1. Press the OK key to enter the main menu, and then select Settings->Handset Name. 2. Edit the value in the Rename field. 3. Press the Save soft key to accept the change. Volume Adjustment • Press or when the handset is idle or ringing to adjust the ringer volume. • Press or during a call to adjust the receiver volume of speakerphone/ earpiece/earphone. Ring Tones 1.
To delete a contact: 1. Press the OK key to enter the main menu, and then select Directory->Local Directory. 2. Press or to highlight the desired entry. 3. Press the Options soft key, and then select Delete to delete the selected entry. Speed Dial 1. Press the OK key to enter the main menu, and then select Settings-> Telephony->Speed Dial. 2. Press or to highlight the desired digit key, and then press the Assign soft key. 3. Press or to select the desired directory type. 4.
2. Press or to highlight the desired entry, and then press using the default line. To place a call from the redial list: 1. Press when the handset is idle. 2. Press or to highlight the desired entry, and then press or to dial out or . To place a call using the speed dial key: Long press the speed dial key to call the preset number directly. Answering Calls To answer a call, do one of the following: • Press the Accept soft key. • Press . • Press . • Press .
Call Transfer You can transfer a call in the following ways: Blind Transfer 1. Press the Options soft key during a call, and then select Transfer. 2. Enter the number you want to transfer the call to. 3. Press the Transfer soft key. Semi-Attended Transfer 1. Press the Options soft key during a call, and then select Transfer. 2. Enter the number you want to transfer the call to. 3. Press , or to dial out. 4. Press the Transfer soft key when you hear the ring-back tone. Attended Transfer 1.
About Yealink Yealink (Stock Code: 300628) is a global leading unified communication (UC) terminal solution provider that primarily offers video conferencing systems and voice communication solutions. Founded in 2001, Yealink leverages its independent research and development and innovation to pursue its core mission: “Easy collaboration, high productivity.” The company’s high-quality UC terminal solutions enhance the work efficiency and competitive advantages of its customers in over 100 countries.
FCC CAUTION: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
