iti YARDMAN -electric Concrete Mixer Operator's Manual MODEL NUMBER YMO115 SERIAL NUMBER PURCHASE DATE Both model number and serial dauber may be found on the main label {see Page 2, Figure 1), “os should re both of therm ina safe aft ute use, FOR YOUR SAFETY READ AND UNDERSTAND THE ENTIRE MANUAL BEFORE OPERATING MACHINE Tame the Great Dollars
Your new YARDMAX® electric concert quality construction, and is With proper years of dependable mixer offers sy and safe to operate iris designed to give you many service. Prepare tu experience the ¢ with the portability electric mixing! take on any job d convenience of clean, Discover the YARDMAN Advantage AL YARDMAN, we ung definitely has its privily; great deal of responsibility dd to respond, will you great outdoors? and th , but it alas c y.
i Culturally road tot uh this cutie operator's Manuel before using your new Concrete mixer Pay attention to alt cations and warnings.
Believable le Be SAFETY KNOW YOUR CONCRETE MIXER Read this manual and all labels to understand your YARDMAN concrete miner and its imitations and potential hazards, DRUGS, ALCOHOL, AND MEDICATION Do not operate your concrete mixer while under the influence of drugs, alcohol, or any medication that could affect your ability to use it property.
DU NONENFORCEABLE PROTECT THE ENVIRONMENT Donor use the concrete mixer for any other propose than that for Take loft over mars rials to an authorized collection pilot or which it was intended. Do not start the motor if the drums fully followup prestidigitation in the Shitty hers thinkable side, Dy invaded. Do not turn the mixer off if it steel contains concrete. The not discharge ts deals, sol or Water! mixer is not to be towed.
Believable le Be CONTENTS SUPPLIED Your YARDMAN concrete mixer comes partially assisted and contains the following: A, 1. Upper Prom ii EEE 2. Bottom Drum with Support Are 3. Locking Plate Mani ne = A Rotor Assembly pin 85 iy 5. Tipping Ber si . 6. Wii Wades {1 Pair) Supportable he Goode 8. Support Frame Om OUD msi He 9. Wheel Axle Bracket Om Coos Mil 20 Li 10. Wheels (1 Air) Gol . o 13 Motor Support Bracket oo 42. Operator's Marla COE mine wl 13.
ASSEMBLY This concrete miter Is partially assembled at the factory. To assemble your machine follow the below instructions. ; A assembly requires two persons (recommended). STAND 1. Insert a split pinto the inner hole in each stub axle (See Figure ta, Frustration 3-4 for details). Then, place a flat washer onto the axle, followed by the wheel, and then another flat washer, Insert another spit pinto the outside axe hole. Bend each of the side pins outward so they do not fall cut.
BOTTOM DRUM Side the Rotor Sin port Bracken oi the shaft. Hold ti place wil ing (See Figure 2 illustration 1) with 242 2. Carefully place the bottom drum with support arm onto the side supports of the stand as shown. (See Figure 2, Frustration 3. The motor support bracket and support seat should slide info the side support channel on each side. The larger diameter shaft should be af the leg end of the stand, 3.
UPPER DRUM TIPPING BAR 1. Place the upper drum onto the bottom drum by aligning both | 17 Slide the Rocking plats over the Fargo metier shaft at the the mounting holes. and the labeled arrows, Illustration 18 2} 2. Insert a MBx20 cross headed screw into sate mounting holes in the rim. Secure each screw from below with a fat washer, Ty rock washer and nut. Make sure the tightening process is carried aut progressively. (See Figure 4, inclinations 3) 3.
Insert the spring anti ihe Ba pipe. hold the spring fo birthplace antigen and place the bur over the larger diameter shalt so th spring stave inside the bay pipe {Ses Figure 5b Frustration 1) PAS LOW Of Di igi GLE LS TOTS In UU ACRE Tie ap with the hole drilled in the shaft. (Sex Figure 5b, frustration 2) Insert a M1085 hex bolt through the hole, place a fat washer on the bolt, and secure with Faust.
Sine hc Been MAINTENANCE REPLACING THE BELT Leisure the extension Cord allays unplugged before. ‘the gator voter is removed. + Remove the motor. (see Figure 9a) The drive bell maintains a constant, even tension provided by the spring-loaded jockey. No adjustment fs needed other than an occasional touch of grease on the spindle. The bearings are sealed for life, ~~ The wiring diagram and parts schematic in this marl are for reference purposes only.
WIRING DIAGRAM TROUBLESHOOTING Problem Cause Motor stops working Thermal protege or nrc 1. Belt has broken Drumfaiistorotate 2. Motor stops working dus to overheat Remedy Stop working for a white until motor cools 1. Replace the new belt 2.