(12'x16’ MERIDIAN WOOD GAZEBO with ALUMINUM ROOF Installation and Operating Instructions —YM11915 HEIGHT: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY 104" / 3.15m Revised 05-14-2020 ARTISTRY Artistry — North America Toll Free Customer Support: 1.888.509.4382 www.yardistrystructures.com \.
A\Important Safety Notice! Artistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: « A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds. « As load bearing support for a building, structure, heavy objects or swings. « Used in structures that trap wind, rain or snow that would create extra load on the product. Accumulated snow must be removed from roof. DO NOT climb or walk on roof for any reason.
Limited Warren This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states/provinces do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
Instructions for Proper Maintenance Your Artistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it. HARDWARE: + Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR 1303. + Inspect and tighten all hardware after completion of assembly; after first month of use; and then annually.
Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PER-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) « Work on a raised, solid and flat surface such as, a table or saw horse. « Keep all connections flush where shown in the instructions. + When assembling the beams keep parts flat, straight and snug when connecting. METAL PARTS: + Roofing material may have sharp edges, wear safety gloves.
Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pergola Room. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a per-existing or new wood or concrete surface. = The hardware to attach the Post Mount to the structure is included.
Permanent Installation Examples cont. Concrete Patio [min. 11° x 15’ (3.616 m x 4.836 m)] with 6” (15.24 cm) clearance on all sides Wood Deck [min. 11° x 15’ (3.616 m x 4.836 m)] with 6” {15.24 cm)clearance on all sides Post Mount Anchoring Hardware {not included) Post Mounts have a 1/2" (12.7 mm) diameter hole for anchoring hardware.
7 1 Dimensions are approximate and are shown to assist In the identification of parts for ifi cat on ( assembly. Actual dimensions may be smaller or larger. ) 16pc. (422) Plinth 190.5mm Y50131-422 2pc. (1012) Straight Gusset Right 1153mm x A“ J Ysoiar-ien » 2pc. (1017) Short Gusset RT 1096.3mm 2pc. (660) Left Beam Short 1769.7mm 2pc. (1011) Straight Gusset Left 1153mm 2 7 poisoning RY 2pc. (1016) Short Gusset LT 1096.3mm oe =4 Ys0131-1018 % wow . | yon se0 Co. 2pc. (661) Right Beam Short 1769.7mm 4pc.
Part Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pc. (624) Rafter Comer Left 2597.8mm (102%7) smn — ¥50131-624 4pc. (623) Rafter Corner Right 2597.8mm ws beg. pe w SET Lo 2pc. (627) Fascia Left Short 1855.5mm [1 lysosomes 2pc. (628) Fascia Right Short 1855.5mm | Y50131.63R 2 4pc. (629) Rafter Short RT 805.5mm 2 Y50131.629 ¢ 4pc. (630) Rafter Short LT 805.5mm Wesson 0) 4pc.
1 i Dimensions are approximate and are shown to assist In the identification of Hardware identification ( parts for assembly. Actual dimensions may be smaller or larger. 4pc. Short Panel Left 4pc. Long Panel Right (Y01033-200) P {Yor 43197) ° V 4pc. Middle Panel (Y01033-196) hh 4pc. -Long Panel Left Tec. Roof Panel Set 4pc. -Short Panel Right (Y70833-195) (Y01033-199) 2pc. Roof Edge Left 72.2 (Y01033-134) E 2pc. Roof Edge Right 72.2 (Y01033-135) < 8pc. Ridge Clip 102.5 (Y01033-133) 2pc. Roof Edge Right 96.
Hardware Identification ~~ ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 1pe. Post Mount (8PK) (Y70819-109} 1pc. Tie Wrap Bracket (8Pk} (Y70819-106} JED apc. 1pc. Roof Peak Set Roof Peak Bracket (Y70829-215) (Y00429-125) © =) 3pc. 3 1/4” Nut pc. (Y08490-200) Contour Washer 3pc. Peak Post ® (Y05918-211) (Y01000-094) 3pe. 3 prong Ci Loop Camille Bolt 09490-001 (ve ) (Y20018-003) (V07455.260) 1pc.
Step 1: Inventory Parts Read This Before Starting Assembly This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. » Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B. If there are any missing or damaged pieces or you need assistance with assembly please contact the consumer relations department directly.
Step 2: Post Assemblies A: At the bottom of four (1018) M Posts insert two 5/16” T-Nuts as shown in F2.1 and F2.2. B: At the bottom of each (1018) M Post place two Post Mounts tight to the bottom and inside faces as shown in F2.1 and F2.2. Loosely attach with one 5/16 x Hex Bolt (with 5/16” lock washer and large washer) per mount so they connect to the T-Nuts. C: On each side of the Posts, place one (422) Plinth flush to the bottom and attach with four #8 x Wood Screws per plinth. Rounded edges on top. (F2.
Step 3: Short Beam Assembly Part 1 A: Connect one (660) Left Beam Short and one (661) Right Beam Short using three 5/16 x Hex Bolts (with 5/16” lock washer, large washer and 5/16 t-nut) as shown in F3.1 and F3.2. Notice orientation of bolt heads. B: Connect one (665) End Short Beam to each end of one (664) Center Beam Short using three 5/16 x Hex Bolts {with 5/16” lock washer, large washer and 5/16” t-nut) per end as shown in F3.1 and F3.3. Notice orientation of bolt heads.
Step 3: Short Beam Assembly Part 2 D: Place one Short Beam L-R Assembly and one End Short Beam Assembly together so the beam assembly ends are flush and the angled ends match. Bolt heads must be on the outside of both beam assemblies. Match the bolt holes in each assembly then loosely attach with four 5/16 x 3" Hex Bolts (with 5/16” lock washer, 1/45/16” large washer and 5/16” t-nut) in the top holes. (F3.4 and F3.5) E: Secure assemblies with 18 #8 x Wood Screws then tighten bolts. (F3.
Step 4: Long Beam Assembly Part 1 A: Connect one (649) Outer End Right and one (650) Outer End Left using two 5/16 x Hex Bolts (with 5/16" lock washer, large washer and 5/16” t-nut) as shown in F4.1 and F4.2. Notice orientation of bolt heads. B: Connect one (656) Inside Beam to each end of one (653) Inside Long Beam using two 5/16 x Hex Bolts {with 5/16" lock washer, large washer and 5/16” t-nut), in the middle holes, as shown in F4.1 and F4.3. Notice orientation of bolt heads.
Step 4: Long Beam Assembly Part 2 D: Place one Long Beam Insert centered on the inside of one Inside Beam Assembly (t-nut side). Match the bolt holes in the Inside Beam Assembly and Long Beam Insert then attach with ten #7 x 3/4" Wood Screws. (F4.4, F4.5 and F4.6) E: Repeat Step D for the second Inside Beam Assembly. orientation of angled ends F4.4 Inside Beam Assembly Long Beam Insert Match bolt Long Beam Insert Inside Beam Office countersink Assembly screw side F4.
Step 4: Long Beam Assembly Part 3 F: Place one Outer Beam Assembly and one Inside Beam Assembly together so the beam assembly ends are flush and the angled ends match. Bolt heads must be on the outside of both beam assemblies. Match the bolt holes in each assembly then loosely attach with eleven 5/16 x 3” Hex Bolts (with 5/16" lock washer, large washer and 5/16” t-nut). The bolts at each end must go in the top holes. (F4.7, F4.8, F4.9 and F4.
Step 5: Frame Assembly and Anchoring Q Part hard, flat surface place one Short Beam Assembly against the outside of two Post Assemblies, on the short side, flush to the tops and outside comers. Attach Beam to Post, through the middle hole, with one 3/8 x Hex Bolt (with two 3/8" large washers and one 3/8” lock nut) per Post. (F5.1 and F5.2) The distance from the outside of one Post Assembly to the outside of the second Post Assembly should be 10’ 103/8". See F5.3 for accurate positioning of Posts.
Step 5: Frame Assembly and Anchoring Part 2 Note: The beveled ends on each gusset should always face away from the wood it Is attaching fo.
Step 5: Frame Assembly and Anchoring Part 3 F: Move your Short Side Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. G: With helpers stand up Short Side Assemblies then place one Long Beam Assembly against the outside of two Post Assemblies, flush to the tops and outside corners and tight to Short Beam Assembly.
Step 5: Frame Assembly and Anchoring Part 4 Note: The beveled ends on each gusset should always face away from the wood it is attaching fo. H: Make sure the Frame Assembly is square and level then facing one Long Beam Assembly from the outside place one (1012) Straight Gusset Right on the right hand side Post Assembly so the top fits tight to the Long Beam Assembly and the bottom fits tight to the Post Assembly.
Step 5: Frame Assembly and Anchoring 3 Part 5 % K: Pr-drill with a 1/8” drill bit then attach Long Beam Assemblies to Post Assemblies with one 5/16 x Lag Screw (with large washer) per corner in the middle holes and Short Beam Assemblies fo Post Assemblies with two 5/16 x Lag Screws (with large washer) per comer in the top and bottom holes. (F5.11) L: Depending on what you are placing the Gazebo on will determine how you anchor it to that surface. Please refer to pages 6 and 7 for installation examples.
Step 6: Fascia Beam Assembly Small Roof Assembly A: Tightly connect one (627) Fascia Left Short and one (628) Fascia Right Short using one 5/16 x Hex Bolt (with 5/16" lock washer, large washer and 5/16” t-nut) as shown in F6.1 and F6.2. Repeat to make a second Fascia Beam Assembly. 114-5018" Large Washer F6.
Step 7: Small Roof Assembly Part 1 A: On each side of one (634) Rafter place one (624) Rafter Comer Left and one (623) Rafter Comer Right so the tops and edges are flush then attach with two #8 x Wood Screws per side. (F7.1 and F7.2) B: Place Fascia Beam Assembly from Step 6 on the bottom of (624) Rafter Comer Left, (623) Rafter Comer Right and (634) Rafter so the sides are flush then attach with one #8 x Wood Screw at each end and one #8 x Wood Screw in the middle. (F7.1, F7.3, F7.4 and F7.
Step 7: Small Roof Assembly Part 2 D: Place one (629) Rafter Short RT, one (632) Rafter Center RT, one (631) Rafter Center LT and one (630) Rafter Short LT over the pilot holes in the Fascia Beam Assembly so they are flush to the top of the assembly and tight to both (623) Rafter Comer Right and (624) Rafter Comer Left, as shown in F7.6. Attach Fascia Beam Assembly to rafters with one #8 x Wood Screw per rafter. Repeat for second Small Roof Assembly. (F7.6, F7.7 and F7.8) (624) Rafter (629) Rafter F7.
Step 7: Small Roof Assembly Part 3 E: Place one (636) Top Strap, one (637) Mid Strap, one (687) Bottom Strap LT and one (688) Bottom Strap RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (687) Bottom Strap LT and (688) Bottom Strap RT sit tight together. Attach with four #8 x Wood Screws per strap. Complete for each Small Roof Assembly. (F7.9, F7.10 and F7.11) (623) Rafter (636) Top Comer Right F7.
Step 7: Small Roof Assembly Part 4 F: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Comer Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Comer Left with two #8 x Wood Screw per rafter. (F7.12 and F7.13) G: Attach (636) Top Strap, (637) Mid Strap and (687) Bottom Strap LT to rafters with 16 #8 x Wood Screws. (F7.14) H: Complete Steps F and G for both Small Roof Assemblies.
Step 8: Attach Officiants Small Roof Assembly A: Tum over each Small Roof Assembly then place two (648) Officiants tight together at center of (634) Rafter and tight to the top of Fascia Beam Assembly. Attach (648) Officiants to (634) Rafter, (623) Rafter Comer Right, (624) Rafter Corner Left, (629) Rafter Short RT, (630) Rafter Short LT, (632) Rafter Center RT and (631) Rafter Center LT with four #8 x 1” Pan Screws per offsite. (F8.1 and F8.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING —DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush. Over tightened and Crushed Snug and Tight The roofing screws can easily crush the Roof Panels and Roof Edges when using a power drill.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.
Step & Attach Roof Panels Small Roof Assembly al A: Place one Long Panel Left on the front of one Small Roof Assembly so it is flush to the side of (624) Rafter Comer Left and a slight overhang at the bottom of the Fascia Beam Assembly. Center holes should line up with (634) Rafter. (F9.1 and F9.2) B: Place one Long Panel Right on Small Roof Assembly so it overlaps the Long Panel Left and it is flush to the side of (623) Rafter Comer Right and a slight overhang at the bottom of the Fascia Beam Assembly.
Step Sr Attach Roof Panels Small Roof Assembly al E: Place one Short Panel Left on Small Roof Assembly so it overlaps the Long Panel Left and it is flush to the sides of (624) Rafter Comer Left and a slight overhang at the bottom of the Fascia Beam Assembly. There should be no overhang at the corners. (F9.3 and F9.
Step 10: Attach Ridge Clips and Roof Edges Q Small Roof Assembly A: Place one Roof Edge Left 72.2 and ons Roof Edge Right 72.2 on the bottom of each Small Roof Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with Roofing Screws per Small Roof Assembly. (F10.1 and F10.2) B: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.
Step 11: Fascia Beam Assembly Large Roof Assembly A: Tightly connect one (625) Fascia LT Long and one (626) Fascia RT Long using one 5/16 x Hex Bolt {with 5/16” lock washer, large washer and 5/16" t-nut) as shown in F11.1 and F11.2. Repeat fo make a second Large Fascia Beam Assembly. Ei Tight F11.
Step 12: Large Roof Assembly ] Part 1 A: Place one (635) Long Roof Top in between both (634) Rafters. (635) Long Roof Top to be flush to the tops to the ends of each (634) Rafter. Attach each (634) Rafter to (635) Long Roof Top with two #8 x Wood Screws per Rafter. (F12.1) B: Measure (1.764 m) from the inside ends of the Large Fascia Beam Assembly then place one (634) Rafter aver each pilot hole, flush to the top of the Large Fascia Beam Assembly and attach with one #8 x Wood Screw per rafter. (F12.
Step 12: Large Roof Assembly Part 2 E: On the sides of Large Fascia Beam Assembly place one (624) Rafter Corner Left and one (623) Rafter Comer Right so the tops and edges are flush then attach to (634) Rafters with two #8 x Wood Screws per board and to Large Fascia Beam Assembly with one #8 x Wood Screw per board. (F12.3, F12.4 and F12.5) F: Place one (629) Rafter Short 48214 Wood RT, one (632) Rafter Center #8 x ’ RT.
Step 12: Large Roof Assembly Part 3 I: On only one Large Roof Assembly, place two (645) Spacers on (635) Long Roof Top. To find the correct placement of each spacer insert one 1/4 x Hex Bolt through (635) Long Roof Top into each (645) Spacer. The bolts are for placement only, they are to be removed at the end of this step. Attach each spacer to (635) Long Roof Top with two #8 x Wood Screws per spacer. Remove bolts, to be used in Step 18. (F12.6) (645) Spacer F12.
Step 12: Large Roof Assembly Part 4 E: Place one (640) Strap Top LG, one (641) Strap Mid LT, one (642) Strap Mid RT, one (643) Strap Bot LT and one (644) Strap Bot RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (641) Strap Mid LT and (642) Strap Mid RT sit tight together and (643) Strap Bot LT and (644) Strap Bot RT sit tight together.
Step 12: Large Roof Assembly Part 5 F: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Corner Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Comer Left with two #8 x Wood Screw per rafter. Complete for each Large Roof Assembly. (F12.9 and F12.10) (624) Rafter (623) Rafter F12.
Step 12: Large Roof Assembly Part 6 G: Attach (640) Strap Top LG, (641) Strap Mid LT, (642) Strap Mid RT, (643) Strap Bot LT and (644) Strap Bot RT to (629) Rafter Short RT, (632) Rafter Center RT, (630) Rafter Short LT, (631) Rafter Center LT and both (633) Center Rafters with 24 #8 x Wood Screws. Complete for each Large Roof Assembly. (F12.11 and F12.12) (640) Strap F12.
Step 12: Large Roof Assembly Part 7 H: Turn over each Large Roof Assembly then place one (639) Fascia Block in between both (633) Center Rafters, flush to the front of the Large Fascia Beam Assembly. Attach (639) Fascia Block to Large Fascia Assembly with two #8 x Wood Screws. (F12.13 and F12.14) I: Place two (647) Offsite Longs tight to the top Large Fascia Assembly so they meet tight together in the center and are flush with the outside edges of (623) Rafter Corner Right and (624) Rafter Comer Left.
Step 13: Attach Roof to Beam Brackets Large Roof Assembly A: On the back of each Large Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each (633) Center Rafter with one 1/4 x 2” Hex Bolt (with two large washers and one 1/4” lock nut) per bracket. (F13.1 and F13.2) F13.
Step 14: Attach Roof Panels Large Roof Assemblies Q Part 1 IMPORTANT!: Before starting this step, be sure to refer back to pages 32 & 33 regarding correct Installation and handling of the roofing. A: Tum over Large Roof Assemblies. Place two Middle Panels flush to the top of (635) Long Roof Top. On each side of the Middle Panels place one Long Panel Left and one Long Panel Right. There will be an overhang at the bottom over Large Fascia Assembly but no overhang at the Corner Rafters.
Step 14: Attach Roof Panels Large Roof Assemblies Part 2 C: Place one Short Panel Left so it overlaps Long Panel Left and is flush to the side of (624) Rafter Corner Left. Place one Short Panel Right so it overlaps Long Panel Right and is flush to the side of (623) Rafter Corner Right. There will be a slight overhang a the bottom of the Large Fascia Beam Assembly. There should not be any overhang at the comers. (F14.4 and F14.
es Attach Roof Edges Large Roof Assembly Step 15 Place one Roof Edge Left 96.2 and one Roof Edge Right 96.2 on the bottom of each Large Roof Assembly so the ends are flush with the outside ends of the Large Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with Roofing Screws per Large Roof Assembly. (F15.1 and F15.2) Right 96.2 Roof Edge #ax 1" Roofing Screws (x 23) Large Fascia Beam Assembly Roofing Screw 2x Roof Edge Right 96.2 2x Roof Edge Left 96.
Step 16: Attach Ridge Clips Large Roof Assemblies Q@ A: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.5 on each side of each Large Roof Assembly so they cover the panels and are flush to the tops of (623) Rafter Corner Right and (624) Rafter Corner Left. The bottom edge of each Ridge Clip 102.5 should be (63.5 mm) up from the bottom edge of (623) Rafter Corner Right and (624) Rafter Comer Left. Attach with five #7 x 3/4” Wood Screws per Ridge Clip 102.5. (F16.
Step 17: Peak Cap Assembly 1 A: Insert three Carriage Bolts with Contoured Washers through the top of Peak Cap Assembly. Place one Peak Post over each Carriage Bolt and secure with Spring Clips. The Spring Clip holds the assembly together. (F17.1 and F17.2) Ca raga Bolt F17.1 Contoured Washer Peal Post Peak Cap Spring Clip Peak Cap Assembly Components; Hardware 1 x Peak Cap Assembly 3 x Carriage Bolt 3 x Contoured Washer 3 x Peak Post 3 x Spring Clip 50 supportgRyardistrystiuciurss.
Step 18: Attach Large Roof Assemblies to Frame art A: With all five assemblers lift Large Roof Assembly with (645) Spacers centered on the Long Beam Assembly. With an assembler holding the first Large Roof Assembly in place lift the second Large Roof Assembly on the opposite Long Beam Assembly. Loosely attach Large Roof Assemblies at the top with two 1/4 x Hex Bolts (with two large washers and one 1/4” lock nut). The bottom of the Rafter Corners should be aligned with the miter of the Beam Assemblies (F18.
Step 18: Attach Large Roof Assemblies to Frame (AEH) Part 2 B: From the outside of the assembly have one person push one Large Roof Assembly in so (648) Offsite fits tight to the Long Beam Assembly and two people pushing up at the peak. One person fastens each Roof to Beam Bracket to (633) Center Rafters then to the Long Beam Assemblies with three #12 x Pan Screws. Install top screw into (633) Center Rafter first then other two into the beam. Tighten bracket bolts.
Step 18: Attach Large Roof Assemblies to Frame (AEH) Part 3 C: Attach one Roof to Beam Bracket to each (634) Rafter on both Large Roof Assemblies with one 1/4 x 2” Hex Bolt (with two large washers and one 1/4” lock nut) and three #12 x Pan Screws, per bracket. (F18.5 and F18.6) D: Tighten both bolts which join Large Roof Assemblies. (F18.
Step 18: Attach Large Roof Assemblies to Frame Part 4 E: With one person on each end of the roof place Peak Cap Assembly on top of Large Roof Assemblies so Carriage bolts with Peak Post fit through gaps between the roof assemblies. (F18.8) F: Insert one 1/4” Nut into one Peak Loop. Be careful nut is loose and will fall out until attached to Carriage Bolt. (F18.9) G: Place one Peak Bracket over the middle Carriage Bolt then attach Peak Loop to Carriage Bolt and twist to tighten. (F18.10) F18.
Step 19: Attach Small Roof Assemblies to Frame (8) A: With all four assemblers lift one Small Roof Assembly up and over the Short Beam Assembly. You will need to lift the Roof Peak Assembly to get the top under it. Loosely attach each (623) Rafter Comer Right to each (624) Rafter Comer Left with three 1/4 x Hex Bolts (with two large washers and one 1/4” lock nut) per side. To align bolt holes helper in the center may have to push up the center of the panels and others make sure comers are aligned.
Step 20: Secure Roof Corners 1 A: From outside the assembly attach Small Roof Assemblies and Large Roof Assemblies together at the Fascia Beam Assembly and Large Fascia Beam Assembly with two #8 x Wood Screws per corner. A helper may need to lift the center of the roof to bring the comers tight together. (F20.
Step 21: Attach Roof to Beam Brackets Small Roof Assembly A: On each Small Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each rafter with one 1/4 x 2” Hex Bolt (with two large washers and oneness” lock nut) per bracket. (F21.1 and F21.2) B: Push panels up from the outside and inside top to make sure each (648) Offsite is tight to the Short Beam Assemblies then fasten each Roof to Beam Bracket with three #12 x Pan Screws per bracket.
Step 22: Attach Roof to Beam Brackets Large Roof Assembly A: On both Large Roof Assemblies, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each (629) Rafter Short RT, (630) Rafter Short LT, (631) Rafter Center LT and (632) Rafter Center RT with one 1/4 x 2° Hex Bolt (with two large washers and one 1/4" lock nut) and three #12 x Pan Screws per bracket. Install top screw into the rafter first then install the other two into the beam. (F22.1 and F22.
Step 23: Attach Ridge Caps to Roof Panels (A) (F23.1 and F23.2) A: At each comer, slide one Ridge Cap Long 81.5 over the Ridge Clips, from the bottom up with cut end leading. B: Slide Ridge Cap Short 25.2 over the Ridge Clips leading with the insert end to push the Ridge Cap Long 81.5 to the top, lifting Peak Cap Assembly so Ridge Cap Long 81.5 fit under. Attach with two #8 x 3/4” Sheet Metal Screws per Ridge Cap set. (F23.1, F23.3, F23.4 and F23.5) Ridge Clip 1025 Peak Cap AN Assembly / F23.1 F23.
Step 24: Secure Roof Peak Detail (A) A: Insert one 1/4” Nut into two Peak Loops. Be careful nut is loose and will fall out until attached to Carriage Bolt. (F24.1) B: Insert two Roof Peak Brackets through each end Carriage Bolt, so they fit over the Rafter Corners, and attach Peak Loops to Carriage Bolts then twist to tighten. (F24.2, F24.3 and F24.
Step 25: Attach Tie Wrap Brackets and Ties =A) A: Attach one Tie Wrap Bracket tight to each end of four (646) Ties with one #10 x Pan Screw per bracket using the inside holes. (F25.2 and F25.3) B: With a helper place one (646) Tie with brackets against each (633) Center Rafter and each (634) Rafter on Large Roof Assemblies so (646) Tie is tight to the rafters and are level. Attach Tie Wrap Bracket to Rafters with two #10 x Pan Screws on both sides of each bracket. (F25.1, F25.2 and F25.
Step 26: Attach Twist Brackets Q A: Measure down from the inside of each Post Assembly on the long side of the unit, place bottom of either 45° Twist Bracket LT or 45° Twist Bracket RT at measured location then attach to Post Assembly and Corner Rafter (Left or Right) with three #12 x Pan Screws per bracket. (F26.1 and F26.2) Rafter Comer (Left or Right) 46° Twist Bracket F26.2 (LT RT) #12x 1-172 Pan Screw Post SS .
Step 27: Metal Hooks and Plaque % J A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the Rafters as needed. Pr-drill with a 1/8" drill bit before installing. (F27.1 and F27.2) B: Attach Gazebo ID Plaque to a prominent location on your gazebo with two #10 x Pan Screws. This provides warnings concerning safety and important contact information.
