TOSHIBA Satellite A200/ Satellite Pro A200 Portable Personal Computer User’s Manual
Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
InterVideo and WinDVD are registered trademarks of the InterVideo Inc. DVD MovieFactory is trademarks of the Ulead Systems. Inc. Other trademarks and registered trademarks not listed above may be used in this manual.Labelflash™ is a trademark of YAMAHA CORPORATION. Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S. patents and other intellectual rights owned by Macrovision Corporation, and other rights owners.
❑ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. 115 V/ 60 Hz in most of North and South America and some Far Eastern countries such as Taiwan. 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, serial port, parallel port, PS/2 mouse/keyboard port and microphone jack.
BSMI Notice (Taiwan Only) EU Declaration of Conformity TOSHIBA declares, that the product: Satellite A200/Satellite Pro A200 conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causng Equipment Regulations. Cet appareil numérique de la class B respecte toutes les exgences du Règlement sur le matériel brouileur du Canada. Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN).
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request. Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
❑ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
❑ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ❑ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Following information is only for EU-member states: The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
CD-RW/DVD-ROM drive safety instructions CAUTIONS: 1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
TEAC DW-224E Location of the required label CERTIFICATION TISH PRODUCT COMPLIES WITH DHHS RULES21CFR CHAPTER 1, SUBCHAPTER J APPLICABLE DATE OF MANUFACTURE MANUFACTURED: TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN User’s Manual xvii
DVD Super Multi (+-R DL) drive safety instructions CAUTIONS: 1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
TEAC DV-W28E Location of the required label CERTIFICATION TISH PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE DATE OF MANUFACTURE MANUFACTURED: TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN HLDS GSA-T20N Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Panasonic Communications Co.
Pioneer DVR-K17T Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by PIONEER CORPORATION 4-1. Meguro 1-chome, Meguro-ku TOKYO 153-8654, JAPAN Toshiba Samsung TS-L632D Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface Manual contents............................................................. xxxi Conventions .................................................................. xxxii Abbreviations ............................................................... xxxii Icons ............................................................................ xxxii Keys............................................................................. xxxii Key operation.............................................
Utilities and Application ................................................1-13 Options ...........................................................................1-16 Chapter 2 The Grand Tour Front with the display closed .........................................2-1 Left side ............................................................................2-3 Right side..........................................................................2-4 Back side ........................................................
For HDD Recovery model............................................3-11 Restoring the preinstalled software from your creating Recovery Media..............................................................3-12 For HDD Recovery model............................................3-12 Chapter 4 Operating Basics Using the Touch Pad/Dual Mode Pad ............................4-1 Dual Mode Pad Button function .....................................4-2 Using the Fingerprint Sensor ........................................
CD/DVDs .....................................................................4-29 Diskettes ......................................................................4-29 Using the software .......................................................4-31 Using the microphone ...................................................4-32 Modem ............................................................................4-32 Region selection ..........................................................4-33 Properties menu ......
Battery indicator.............................................................6-3 DC IN indicator ..............................................................6-3 Power indicator ..............................................................6-4 Battery types ....................................................................6-4 Battery ...........................................................................6-4 Real time clock battery ..................................................
Express Card....................................................................8-4 Installing an Express Card.............................................8-4 Removing an Express Card...........................................8-5 Multiple Digital Media Card Slot .....................................8-6 Installing a SD/SDHC/MS/MS Pro/MMC/xD card ..........8-7 Removing a SD/SDHC/MS/MS Pro/MMC/xD card ........8-8 Memory expansion ..........................................................
Touch Pad/Dual Mode Pad..........................................9-12 USB mouse..................................................................9-13 Fingerprint Sensor .......................................................9-15 PC card........................................................................9-16 Express card................................................................9-16 SD/SDHC/MS/MS Pro/MMC/xD card ..........................9-16 Monitor..................................................
Display Controller and Modes ....................................... B-1 Appendix C V.90/V.92 .......................................................................... C-1 Appendix D Wireless LAN ................................................................... D-1 Appendix E AC Power Cord and Connectors ................................... E-1 Glossary Abbreviations .....................................................
Preface Congratulations on your purchase of the TOSHIBA Satellite A200/Satellite Pro A200 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A200/Satellite Pro A200 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxxiv User’s Manual
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
General Precautions puter for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer low-heat injury. ❑ If the computer has been used for a long time, avoid direct contact with the metal plate supporting the various interface ports as this can become hot. ❑ The surface of the AC adaptor can become hot when in use but this condition does not indicate a malfunction.
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction INTRODUCTION Software Windows Vista™ ◆ The following software is preinstalled: • Microsoft® Windows Vista™ • Modem Driver (Can be used only for Modem models) • Display Drivers for Windows • Wireless LAN driver (Can be used only for Wireless LAN models) • Sound Driver for Windows • DVD Video Player • LAN Drivers • Bluetooth Driver (Can be used only for Bluetooth models) • Pointing Device Driver • TOSHIBA Power Saver • TOSHIBA User’s Manual • TOSHIBA Assist • TOSHIBA ConfigFree • TOSHIBA PC Di
Introduction • Instruction Manual for Safety & Comfort • End User License Agreement Product Recovery Media Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple-mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.
Introduction Disks INTRODUCTION Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes. 60 GB 80 GB 100 GB 120 GB 160 GB 200 GB 250 GB 300 GB Disclaimer (Hard disk drive capacity) CD-RW/DVDROM drive 1-4 For more information on the Disclaimer regarding Hard disk drive capacity, please refer to the Disclaimer section in chapter 10.
Introduction DVD Super Multi (+-R DL) drive • DVD-R • DVD-RW • DVD+R • DVD+RW • DVD-RAM • DVD+R DL • DVD-R DL • CD-DA • CD-Text • Photo CD (single/multi-session) • CD-ROM Mode 1, Mode 2 • CD-ROMXA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 User’s Manual 1-5 INTRODUCTION Some models are equipped with a full-size DVD Super Multi (+- R DL) drive module that lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.
Introduction INTRODUCTION Display The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Thin-film transistor color LCD is available: Graphics controller 15.4" WXGA, 1280 horizontal x 800 vertical pixels Graphics controller maximizes display performance. Refer to Appendix B for more information.
Introduction Universal Serial Bus (USB2.0) Video Out Jack Slots Multiple Digital Media Card PC card (Depending on model you purchased.) Express card (Depending on model you purchased.) This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/SDHC/MS/MS Pro/MMC/xD memory cards). (Provided with some models) A PC card slot accommodates: One 5 mm Type II card. Refer to Chapter 8, Optional Devices, for details.
Introduction Communications INTRODUCTION LAN Wireless LAN Modem (Provided with some models) Bluetooth Wireless Communication Switch 1-8 The computer is equipped with a LAN card that supports Ethernet LAN (10 Mbit/s, 10BASE-T) or Fast Ethernet LAN (100 Mbit/s, 100BASE-TX). It is preinstalled as a standard device in some markets.
Introduction Security Security lock slot Software Operating System TOSHIBA Utilities Plug and Play User’s Manual Windows Vista™ is available. Refer to the preinstalled software section at the front of this chapter. A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
Introduction INTRODUCTION Special Features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Display automatic This feature automatically cuts off power to the internal power off display when there is no keyboard input for a time specified.
Introduction Battery save mode Low battery automatic hibernation Heat dispersal Hibernation Sleep User’s Manual 1-11 INTRODUCTION Panel power on/off This feature lets you save battery power. You can specify the Power Save Mode in the Profile item in TOSHIBA Power Saver. This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened.
Introduction INTRODUCTION TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. TOSHIBA Power Saver TOSHIBA Button Support TOSHIBA Zooming Utility TOHSIBA PC Diagnostic Tool TOSHIBA Flash Cards TOSHIBA Components common Driver TOSHIBA Accessibility 1-12 TOSHIBA Power Saver provides you with the feature of more various power supply managements. This utility controls the following computer button functions.
Introduction Utilities and Application TOSHIBA DVD-RAM Utility "You can boot TOSHIBA Disc Creator from the menu bar as follows. [Start]-[All Programs]-[TOSHIBA]-[CD&DVD Applications]-[Disc Creator]" "TOSHIBA DVD-RAM Utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. Ulead DVD Movie Factory for TOSHIBA ® User’s Manual You can boot TOSHIBA DVD-RAM Utility from the menu bar as follows.
Introduction INTRODUCTION TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. You can boot ConfigFree from the menu bar as follows.
Introduction Fingerprint Utility User’s Manual ❑ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ❑ Files and folders can be encrypted/decrypted and third party access to them prevented. ❑ Disable the password-protected screen-saver when returning from power-saving (sleep) mode. ❑ Power-on Security and Single Sign-On feature. ❑ Authentication of the User Password and Hard Disk Password when booting up the computer.
Introduction INTRODUCTION Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion Two memory expansion slots are available for installing 512 MB, 1024 MB or 2048 MB memory modules. The modules are PC2-4200 or PC2-5300, 200-pin, SO Dual In-line (SO-DIMM).
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Figure 2-1 shows the computer’s front with its display panel in the closed position.
The Grand Tour Microphone jack Headphone jack THE GRAND TOUR Multiple Digital Media Card Slot Multiple Digital Media Card Indicator System Indicators Wireless communication switch A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio input. A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speaker is automatically disabled.
The Grand Tour Left side Figure 2-2 shows the computer’s left side. EXPRESS CARD SLOT OR PC CARD SLOT(DEPENDING FAN VENT PURCHASED PURCH) LAN JACK MONITOR PORT ON THE MODEL YOU USB PORTS I.LINK (IEEE 1394) PORT Figure 2-2 The left side of the computer External monitor port Fan vent This 15-pin port lets you connect an external monitor. Provides air flow for the fan. CAUTION: Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vents.
The Grand Tour Note: When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified. This problem may occur when Windows Vista™ is restarted while the devices are connected or when the power to the IEEE1394 devices is turned on before the PC is turned on. If it occurs, disconnect the IEEE1394 cables and then reconnect them.
The Grand Tour Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.1) Note: Operation of all functions of all USB devices has not been confirmed. some functions might not execute properly..
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. BATTERY THE GRAND TOUR BATTERY PACK LOCK PACK BATTERY RELEASE LATCH MEMORY MODULE COVER Figure 2-5 The underside of the computer Battery pack Battery pack cover latch Battery lock Memory module cover 2-6 The battery pack powers the computer when the AC adaptor is not connected.
The Grand Tour Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
The Grand Tour Fingerprint Sensor (Provided with some models) Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ❑ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer). ❑ Files and folders can be encrypted/decrypted and third party access to them prevented. ❑ Disable the password-protected screen-saver when returning from power-saving (sleep) mode. ❑ Power-on Security and Single Sign-On feature.
The Grand Tour AV Button Play/Pause Button STOP Previous Button Next Button User’s Manual Press this button to begin playing an audio CD, a DVD movie or digital audio files. This button also acts as a Pause button. (The availability of this function depends on the model you purchased.) Press this button to stop play. Press this button to advance to the previous track, chapter or data. Press this button to advance to the next track, chapter or data.
The Grand Tour System indicators Figure 2-7 shows the system indicators, which light when various computer operations are in progress. MULTIPLE DIGITAL MEDIA CARD SLOT DISK THE GRAND TOUR MAIN BATTERY DC IN POWER Figure 2-7 Systems indicators Power source/system indicators DC IN Power Main battery Disk Multiple digital media card slot 2-10 The DC IN indicator glows blue when DC power is supplied from the AC power adaptor.
The Grand Tour The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers. NUMERIC MODE ARROW MODE Arrow mode Numeric mode When the Arrow mode indicator lights green, you can use the keypad overlay (white labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.
The Grand Tour Optical Media drive CD-RW/DVD-ROM drive, DVD Super Multi (+-R DL) drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. Region codes for DVD drives and media THE GRAND TOUR CD-RW/DVD-ROM, DVD Super Multi (+-R DL) drive and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.
The Grand Tour DVDs ◆ DVD-R, DVD+R and DVD+R DL discs can be written only once. The recorded data cannot be erased or changed. ◆ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The Grand Tour DVD Super Multi (+-R DL) drive The full-size DVD Super Multi drive module lets you record data to s as rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. Note: The read speed is slower at the center of a disc and faster at THE GRAND TOUR the outer edge.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-Up Modes for details.
THE GRAND TOUR The Grand Tour 2-16 User’s Manual
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. NOTE: When you open the display, hold it with both hands and lift up slowly.
Getting Started POWER BUTTON Figure 3-4 Turning on the power Starting up for the first time GETTING STARTED When you first turn on the power, the computer’s initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep mode.
Getting Started 3. Click Windows Start button, point to , and then select Shut Down. 4. Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored.
Getting Started Starting Hibernation To enter Hibernation mode, follow the steps below. Windows Vista™ 1. Click Windows Start button. 2. Point to . 3. Select Hibernate. Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2. Open Mobile PC and open Power Options. 3. Select Choose what the power button does. GETTING STARTED 4.
Getting Started Sleep mode In sleep mode the power remains on, but the CPU and all other devices are in sleep mode. CAUTIONS: 1. Before entering Sleep mode, be sure to save your data. 2. Do not install or remove a memory module while the computer is in sleep mode. The computer or the module could be damaged. 3. Do not remove the battery pack while the computer is in sleep mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started When you turn the power back on, you can continue where you left when you shut down the computer. NOTES: 1. When the computer is shut down in sleep mode, the power indicator glows amber. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Sleep mode consumes more power. Sleep limitations Sleep will not function under the following conditions: ❑ Power is turned back on immediately after shutting down.
Getting Started System Recovery Options About 1.5GB hidden partition is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem. System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes some tools to repair startup problems, run diagnostics or restore the system.
Getting Started Restoring the preinstalled software from the Product Recovery disc If preinstalled files are damaged, use the Product Recovery disc to restore them. To restore the operating system and all preinstalled software, follow the steps below. You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options. 1. Load the Product Recovery disc in the drive and turn off the computer's power. 2.
Getting Started Create Optical Recovery Discs For HDD Recovery model A recovery image of your computer is stored on the hard disk. You may use this image to create CD or DVD recovery discs using the following steps: 1. Select either blank CDs or DVDs media. 2. The application will allow you to choose a type of media to create recovery CDs/DVD including: CD-R, CD-RW,DVD-R,DVD-RW,DVD+R and DVD+RW. NOTE: Some media may not be compatible with Optical Drive of your computer.
Getting Started You can not use System Recovery Options if restoring the pre-installed software without System Recovery Options. 1. Turn off your computer. 2. While holding down 0 (zero) key on the keyboard, turn on your computer. 3. A menu appears. Follow the on-screen instructions. Restoring the preinstalled software from your creating Recovery Media For HDD Recovery model If preinstalled files are damaged, use the your creating Recovery Media or using HDD Recovery to restore them.
Getting Started 3. Use the up or down cursor key to select CD/DVD in the display menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup and Passwords. 4. A menu appears. Follow the on-screen instructions. ❑ ❑ When drivers Utilities are installed, you can setup the respective drivers and utilities from the following folder. C: \ TOSAPINS\*** When removing pre-installed drivers/utilities or when installing, you can setup the respective drivers/utilities from the following folder.
GETTING STARTED Getting Started 3-14 User’s Manual
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad/Dual Mode Pad, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Using the Touch Pad/Dual Mode Pad To use the Touch Pad/Dual Mode Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Dual Mode Pad Button function (Dual Mode Pad is provided with some models) MAIL BUTTON CONFIG FREE WINDOWS PHOTO GALLERY SWITCH BUTTON VOLUME APPLICATION BUTTONS Figure 4-2 Dual Mode Pad Button Switch button OPERATING BASICS Volume 4-2 To switch between Cursor Mode and Button Mode. When you switch to Button Mode, the pad blinks blue. Increases or decreases the volume of speaker and headphone. Mail button Starts your mail box for you to receive and send mails.
Operating Basics Windows Photo Gallery Application buttons Windows Photo Gallery gives you many tools for your digital photos and videos.You can organize, find, and view your photos and videos, as well as edit, print, and share them from within Windows Photo Gallery. It also makes it easy to transfer your photos from your camera to your computer, using a simple import process Three application buttons have default setting. You can assign other functions and programs to button 1 to 3.
Operating Basics ❑ Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor. ❑ Do not touch the sensor with a soiled finger. Minute foreign particles on a soiled or dirty finger may scratch the sensor. ❑ Do not paste stickers or write on the sensor. ❑ Do not touch the sensor with a finger or any object with built-up static electricity.
Operating Basics ❑ Fingerprint data is stored into the nonvolatile memory in the fingerprint sensor. Deleting fingerprint data with "Delete" menu on Fingerprint Software Management" before you dispose the computer is recommended. How to Delete the Fingerprint Data Saved fingerprint data is stored in the Non-volatile memory inside the fingerprint sensor. If you hand over the PC to others, or dispose of it, to do the following operations is recommended. 1.
Operating Basics Align the finger and sensor as shown on the above figure. Points to note about the Fingerprint Utility You can back up the fingerprint data or the information registered to Password Bank. Please use "Import or Export User Data" menu on Fingerprint Software Management. Please note the files in Mysafe is not backed up with this menu.
Operating Basics 1. Click Start, Point to All Programs, point to Protector Suite QL and click User Enrollment. Note: You can also start User Enrollment Wizard using the following method. ❑ Click the icon in the Task Bar. ❑ Swipe your finger across the Fingerprint Sensor. 2. The User's Password screen is displayed. Ensure the same Windows logon username is displayed before entering a password into the Enter your Password field. Click Next. 3. Click Next. 4.
Operating Basics Windows Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
Operating Basics Authentication screen is displayed. This will switch the password input screen to the keyboard-based one. Note: ❑ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-On Feature. Please use TOSHIBA HW Setup to register the User Password. ❑ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
Operating Basics Fingerprint Single Sign-On Feature General This is a feature that allows the user to complete the authentication for both the User Password (and optionally, the HDD user and Supervisor passwords) and logging on to Windows using only one fingerprint authentication when booting up. It is necessary to register the User Password and Windows Logon password before using the Fingerprint Power-on Security and this Fingerprint Single Sign On Feature.
Operating Basics How to Swipe the Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. Ensure the center of the fingerprint is on the sensor when swiping the finger.
Operating Basics If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs on CDRW/DVD-ROM drive section for precautions on writing to CDs. If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on DVD Super Multi drive section for precautions on writing to CDs/DVDs. Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the CD-RW/DVD-ROM eject button to open the drawer slightly.
Operating Basics drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. EJECT HOLE Figure 4-4 Manual release with the eject hole 2. Grasp the drawer gently and pull until it is fully opened.
Operating Basics 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD Note: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6. CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Do not keep foreign matter from entering the drive.
Operating Basics Figure 4-7 Closing the DVD-ROM drawer Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-8. CAUTION: Do not press the eject button while the computer is accessing the DVD-ROM drive. Wait for the optical media drive indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button.
Operating Basics Figure 4-8 Removing a CD-RW/DVD-ROM 3. Push the center of the drawer to close it. Press gently until it locks into place. AV Button function (Provided with some models) This section describes a button function.
Operating Basics Writing CDs on CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to either CD-R or CDRW discs. The following applications for writing are supplied: TOSHIBA Disc Creator. Note: CD-R discs can be written to only once. CD-RW discs can be rewritten many times. Important message (CD-RW/DVD-ROM drive) Before you write or rewrite to CD-R/RW disc, read and follow all setup and operating instructions in this section.
Operating Basics ◆ ◆ ◆ ◆ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and damage data. Write from the computer’s HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device.
Operating Basics ◆ Any change or loss of the recorded contents of CD-R/RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents. ◆ Damage that may be caused by using third party equipment or software.
Operating Basics OPERATING BASICS Before writing or rewriting ◆ Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM/+R DL/R DL disc. ◆ However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO., LTD Ricoh Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI KAGAKU MEDIA CO.
Operating Basics Note: This drive cannot use discs that allow writing of 8 speeds or more (DVD-R, DVD+R ), 6 speeds or more (DVD-RW) and 8 speeds or more (DVD+RW). If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ◆ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVDRAM is affected by the quality of the disc and the way it is used.
Operating Basics ◆ Be sure to close all other software programs except the writing software. ◆ Do not run software such as a screen saver, which can put a heavy load on the CPU. ◆ Operate the computer in the full-power mode. Do not use power-saving features. ◆ Do not write while virus check software is running. Wait for it to finish, and then disable virus detection programs including any software that checks files automatically in the background.
Operating Basics ◆ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand. ◆ Keep mobile phones and other wireless communication devices away from the computer. ◆ Always copy data from the HDD to the DVD-RAM. Do not use cut-andpaste. The original data will be lost if there is a write error.
OPERATING BASICS Operating Basics ◆ You cannot back up DVD-ROM, DVD-Video or DVD-R/-R DL/-RW or DVD+R/+R DL/+RW to CD-R/RW using the “Exact Copy” function of TOSHIBA Disc Creator. ◆ TOSHIBA Disc Creator record in packet format. ◆ You might not be able to use the “Exact Copy” function of TOSHIBA Disc Creator to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that was made with other software on a different DVD-R/-R DL/-RW or DVD+R/+RW recorder.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button ( open the Options panels. ) on the TOSHIBA Disc Creator Assist to 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button. Video You can record video using Ulead DVD MovieFactory® for TOSHIBA.
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DVCamcorder: 1. Click [Start] - [All Programs] - [DVD MovieFactory for TOSHIBA] [Ulead DVD MovieFactory for TOSHIBA Launcher] to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3. Click [Video Disc] - [Burn Video to Disc] to launch [Direct Recording] dialog box, choose [DVD-Video/+VR] to invoke [Straight Capture to Disc] Page. 4. Choose [DVD-Video] format. 5.
Operating Basics How to learn more about Ulead DVD MovieFactory Please refer to the on-line Help and Manual files for additional Ulead MovieFactory information. Important information for use Note the following limitations when you write video DVD: 1. Editing digital video. ❑ Log in with Administrator rights to use DVD MovieFactory. ❑ Make sure that your computer is running on AC power when using DVD MovieFactory. ❑ Operate the computer at Full Power. Do not use power-saving features.
Operating Basics • Use the Mode control button and Audio/Video control button to reproduce music or voice. • Open the DVD drive. • Install, remove or connect external devices, including the following: PC card, SD card, USB device, external display, i.LINK devices, optical digital devices. ❑ Please verify your disc after recording important data. ❑ DVD-R/+R/-RW disc cannot be written in VR format. ❑ Not support to output VCD and SVCD format. 3. About Straight to Disc ❑ Not support to record on DVD-R/+R disc.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mark the surface of the CD/ DVD that contains data. 4.
Operating Basics Using the Web Camera(Built-in Web Camera is provided with some models.) OPERATING BASICS This section describes the bundled webcam utility, which can capture still and video images. The web camera will auto-run when Windows starts. 1. Active LED 4-30 2.
Operating Basics Using the software The web camera software is pre-configured to start when you turn on Windows Vista; if you need to restart it go to Start → Programs → Camera Assistant Software → Camera Assistant Software 1. Capture still images 2. Video Pecording 3. Video Pecording 4. Function 5. Display Window 6. Camera Resolution 7. Mute 8. Effects Capture Still Image Click to see a preview of the captured image; you can also e-mail the image. Click to prepare for recording.
Operating Basics Properties Settings Help Choose from the Options tab to flip, zoom, flicker rate, night mode and backlight compensation; in the Image tab change the colour settings; in the profile tab change the lighting conditions.
Operating Basics CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem. Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. To select a region, follow the steps below. 1.
Operating Basics Properties menu Click the icon with the secondary mouse button to display the following menu. Figure 4-11 The menu list (Windows Vista™) Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics CAUTION: If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 wireless LAN standard (Revision A, B, G or Draft N). OPERATING BASICS Supported features.
Operating Basics ◆ stored data. TOSHIBA strongly recommends the customer to enable the WEP/WPA-PSK (AES) function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth Adapter simultaneously.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 Mbit/s, 100BASE-TX), be sure to connect with a category 5 cable, CAT5, or higher. If you are using Ethernet LAN (10 Mbit/s, 10BASE-T), connect with a category 3 cable, CAT3, or higher.
Operating Basics Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Note: Make sure the LAN active indicator (amber LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Operating Basics ◆ Use the carrying case when transporting the computer. ◆ When carrying your computer, be sure to hold it securely so that it does not fall or hit anything. ◆ Do not carry your computer by holding protruded portions. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered.
OPERATING BASICS Operating Basics 4-42 User’s Manual
The Keyboard The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard. By pressing some keys in combination, all the 104/105-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard THE KEYBOARD F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard tion in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Press Fn + Alt to simulate the enhanced keyboard’s right Alt key. Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers.
THE KEYBOARD The Keyboard Instant security: Press Fn + F1 to enter "Lock computer" mode. To restore your desktop, you need to log on again. Power Plan: Pressing Fn + F2 changes the power settings. Sleep: Pressing Fn + F3 switches the system to Sleep mode. Hibernation: Pressing Fn + F4 switches the system to Hibernate mode. Output: Pressing Fn + F5 changes the active display device.
The Keyboard THE KEYBOARD Brightness Up: Pressing Fn + F7 increases the computer's display panel brightness in individual steps. Wireless: Pressing Fn + F8 switches the active wireless devices if the wireless communication switch is switched on. Note: If your wireless communication device is installed, no dialog box will not appear. Touch Pad: Pressing Fn + F9 enables or disables the Touch Pad function. Zoom: Pressing Fn + space changes the display resolution.
The Keyboard THE KEYBOARD Fn Sticky key You can use the Toshiba Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. To start the Toshiba Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
The Keyboard Numeric mode Figure 5-1 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay. User’s Manual 5-7 THE KEYBOARD To turn on the Numeric mode, press Fn + F11.
The Keyboard THE KEYBOARD Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
Chapter 6 Power and Power-Up Modes Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery. User’s Manual 6-1 POWER AND POWERUP MODES The computer’s power resources include the AC adaptor and internal batteries.
Power and Power-Up Modes Table 1: Power conditions Power on Power off (no operation) AC Battery fully • Operates • No charge adaptor charged • No charge • LED: Battery Blue • LED: Battery Blue connected DC IN Blue POWER AND POWERUP MODES DC IN Blue Battery • Operates • Quick charge partially • Charge • LED: Battery Amber charged or • LED: Battery Amber no charge DC IN Blue DC IN Blue No battery • Operates • No charge installed • No charge • LED: Battery off • LE
Power and Power-Up Modes Power indicators The Battery, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status: Flashing amber The battery charge is low. The AC adaptor must be connected to recharge the battery. Indicates the AC adaptor is connected and charging the battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status. Blue Indicates power is being supplied to the computer and the computer is turned on. Blinking amber Indicates the power was turned off while the computer was in Resume mode. POWER AND POWERUP MODES No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power, more than a month, the battery may fail to retain a charge. It may not function efficiently over the expected life of the battery and the Battery LED may not indicate a low-battery condition.
Power and Power-Up Modes Safety precautions Mishandling of batteries can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, Which could result in death or serious injury, if you do not follow instructions. POWER AND POWERUP MODES Warning: Indicates a potentially hazardous situation, Which could result in death or serious injury, if you do not follow instructions.
Power and Power-Up Modes tic liquid and cause death or serious injury. It could also fail or malfunction causing data lose. 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury.
Power and Power-Up Modes 3. Use only battery packs recommended by TOSHIBA as replacements. 4. Always make sure the battery pack is installed correctly and securely. Otherwise, a battery pack could fall out and possibly cause injury. POWER AND POWERUP MODES 5. Change the battery pack only in an ambient temperature between 5 and 35 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6.
Power and Power-Up Modes You must recharge a battery pack when it becomes discharged. Procedures To recharge a battery pack while it is installed in the computer, connect the AC adaptor to the DC IN socket and plug the other end into a working outlet. The Battery indicator glows amber when the battery is being charged. Time The following table shows the approximate time required to fully charge a discharged battery.
Power and Power-Up Modes ❑ The battery has not been used for a long time. ❑ The battery has completely discharged and been left in the computer for a long time. ❑ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2. Plug in the AC adaptor. POWER AND POWERUP MODES 3. Charge the battery until the Battery indicator glows blue.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer (for example, whether you enable batterypower saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (3 cell) Battery pack (6 cell) POWER AND POWERUP MODES Battery pack (9 cell) RTC battery about 2 days (Sleep mode) about 23 days (Shutdown mode) about 4 days (Sleep mode) about 46 days (Shutdown mode) about 6 days (Sleep mode) about 69 days (Shutdown mode) about 3 months Extending battery life
Power and Power-Up Modes ❑ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ❑ Store spare battery packs in a cool dry place out of direct sunlight. Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes amber shortly after fully recharging the battery, the battery pack needs to be replaced.
Power and Power-Up Modes BATTERY PACK LOCK POWER AND POWERUP MODES BATTERY PACK BATTERY RELEASE LATCH Figure 6-1 Slide the locking latch to the unlocked position 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. BATTERY PACK BATTERY PACK LOCK BATTERY RELEASE LATCH Figure 6-2 Removing the battery pack 7. Pull the battery pack forward to remove it. CAUTION: For environmental reasons, do not throw away a spent battery pack.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the battery pack.
Power and Power-Up Modes CAUTION: At this point, the hot keys Fn + F1 to F9 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter. CAUTION: If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. POWER AND POWERUP MODES Power-up modes The computer has the following power-up modes: ❑ Boot: Computer shuts down without saving data.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot priority, Keyboard, USB, LAN, General and password. Note: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) Registered Set the password. A dialogue box will appear to let you set the password.
HW Setup and Passwords To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** Note: If you click the OK button before entering the password, Registered will appear on the display. 3. Click the OK button.
HW Setup and Passwords CPU Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed.
HW Setup and Passwords If there are only 2 HDDs, the Boot Priority Options setting will be like the following. This procedure does not affect the settings. * In this computer, CD-ROM refers to the DVD-ROM, CD-R/RW or CD-RW/ DVD-ROM drives. Note: PC card HDD boot is not supported. To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. Use the up/down cursor keys to select boot device you want and press Enter. NOTES: 1.
HW Setup and Passwords 3. If you press a key other than one of those above or if the selected device is not installed, the system will boot according to the current setting in HW Setup. Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in sleep mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in sleep mode. Enabled Enables Wake-up on Keyboard. Disabled Disables Wake-up on Keyboard.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the PC card. 2. Press the eject button of the PC card you want to remove to extend the button. 3. Press the extended eject button to pop the card out slightly. 4. Grasp the PC card and remove it.
Optional Devices Express Card Installing an Express Card The Express Card slot is located on the left side of the computer. You can install one Express Card in the slot. Windows’ hot-install feature lets you install Express Card while the computer’s power is on. Note: Do not install an Express Card while the computer is in sleep or hibernation mode. Some cards might not work properly. To install an Express Card, follow the steps below. 1. Insert the Express Card. 2.
Optional Devices Removing an Express Card To remove the Express Card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the Express Card. 2. Press the Express Card slightly to make it stretch out. 3. Grasp the Express Card and pull it out from the slot.
Optional Devices Multiple Digital Media Card Slot The computer is equipped with a Multiple Digital Media Card Slot that can accommodate Secure Digital (SD)/ Secure Digital High Capacity (SDHC)/ Memory Stick (MS)/Memory Stick Pro (MS Pro)/Multi Media Card (MMC)/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/SDHC/MS/MS Pro/ MMC/xD memory cards.
Optional Devices Installing a SD/SDHC/MS/MS Pro/MMC/xD card To install the memory card, follow the steps below. 1. Insert the memory card. 2. Press gently to ensure a firm connection. SD/SDHC/MS/ MS PRO/MMC/XD CARD MULTIPLE DIGITAL MEDIA CARD SLOT Figure 8-5 Inserting the memory card CAUTIONS: 1. Keep foreign objects out of the Multiple Digital Media Card Slot. A pin or similar object can damage the computer's circuitry 2.
Optional Devices Removing a SD/SDHC/MS/MS Pro/MMC/xD card To remove the memory card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the inserted memory card. 2. Gently press the memory card inside the socket to eject it. 3. Grasp the card and remove it. SD/SDHC/MS/MS PRO/MMC/XD CARD Figure 8-6 Removing the inserted memory card CAUTIONS: 1.
Optional Devices Memory expansion You can install additional memory in the computer’s memory module to increase the amount of RAM. CAUTION: Only memory modules with the following parts numbers can be installed: 512MB: PA3511U-1M51 1GB: PA3512U-1M1G 2GB: PA3513U-1M2G Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3. CAUTIONS: 1.
Optional Devices Figure 8-7 Removing the cover 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7. Push the module down so that it lies flat and is secured by two latches. OPTIONAL DEVICES CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Figure 8-8 Inserting the memory module 8. Seat the cover and secure it with one screw. 9.
Optional Devices Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. CAUTIONS: 1. If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. 2. Do not try to remove a memory module with the computer turned on or turned off in Sleep and Hibernation mode.
Optional Devices Additional battery pack (6 Cell and 9 Cell) You can increase the portability of the computer with additional battery packs (6 Cell: PA3534U-1BRS/PA3534U-1BAS, 9 Cell: PA3535U-1BRS/PA3535U1BAS). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
Optional Devices If you have selected Simultaneous under the Display options of the HW Setup, both the external monitor and the internal LCD will be active when you turn on the computer. If Auto-Selected is selected, only the external monitor will be active. To change the display settings, press Fn + F5. If you disconnect the monitor before you turn the computer off, be sure to press Fn + F5 to switch to the internal display.
Optional Devices 1. Digital video cameras 2. Hard disk drives 3. MO drives 4. CD-RW drives CAUTION: i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions 1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer.
Optional Devices c. Use S100, S200 or S400 cables no longer than three meters. d. Some devices might not support sleep or automatic off functions. e. Do not connect or disconnect an i.LINK device while it is using an application or when the computer is automatically shutting it down to save power. Data might be destroyed. f. When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified.
OPTIONAL DEVICES Optional Devices 8-16 User’s Manual
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting TROUBLESHOOTING ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem Sometimes the system gives clues that can help you identify why it is malfunctioning.
Troubleshooting Hardware and system checklist ❑ Self test ❑ Express/PC card ❑ Power ❑ SD/SDHC/MS/MS Pro/MMC/xD card ❑ Password ❑ Monitor ❑ Keyboard ❑ Sound system ❑ LCD panel ❑ TV output signal ❑ Hard disk drive ❑ USB ❑ DVD-ROM drive ❑ Modem ❑ CD-RW/DVD-ROM drive ❑ Sleep/Hibernation ❑ DVD +-R/+-RW drive ❑ Memory Expansion ❑ DVD Super Multi drive ❑ LAN ❑ Diskette drive ❑ Wireless LAN ❑ Fingerprint Sensor ❑ Bluetooth ❑ Pointing device ❑ i.
Troubleshooting TROUBLESHOOTING Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Troubleshooting Overheating power down AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow blue) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
TROUBLESHOOTING Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow amber.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet is supplying power. Test it by plugging in an appliance. If it doesn’t work, try another power source. Check whether the battery is hot or cold to the touch.
Troubleshooting Password Procedure Cannot enter password Refer to the Password section in Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup and Passwords. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.
TROUBLESHOOTING Troubleshooting Problem Procedure Problems above remain unresolved or other problems occur Refer to your software’s documentation to determine if the software is causing the difficulty. Contact your dealer if the problems continue. Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive or a CD-ROM is in the optical media drive. Remove any diskette and/or CD-ROM and check Boot priority.
Troubleshooting CD-RW/DVD-ROM drive Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty.
TROUBLESHOOTING Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software during writing. • Do not jar the computer during writing. • Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Procedure Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of DVD/CD you are using.
Troubleshooting TROUBLESHOOTING Diskette drive Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the external 3 1/2" diskette drive Try another diskette.
Troubleshooting Procedure The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1.Open the Control Panel, select the Mouse icon and press Enter. 2.Click the Pointer Option tab. 3.Set the speed as instructed and click OK. When the reaction of Touch pad/Dual Mode Pad is sensitive to slow Adjust the touch Sensitivity. 1.Open the Control Panel. 2.Click the Printers icon and then the Other Hardware icon. 3.Click the Mouse icon. 4.
Troubleshooting TROUBLESHOOTING Problem Procedure Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click sped setting in the mouse control utility. 1.Open the Control Panel, select the Mouse icon and press Enter. 2.Click the Buttons tab. 3.Set the double-click speed as instructed and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1.
Troubleshooting Fingerprint Sensor Procedure Reading of the fingerprint was not successful. Please try again using the correct posture. Refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics. Try the recognition process again using another enrolled finger. The fingerprint cannot be read due to injuries to the finger. Try the recognition process again using another enrolled finger.
Troubleshooting TROUBLESHOOTING PC card Refer also to Chapter 4, Operating Basics. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. Express card Refer also to Chapter 4, Operating Basics. Problem Procedure Express card error occurs Reseat the Express card to make sure it is firmly connected.
Troubleshooting Make sure the card is not write protected. You cannot read a file Make sure the target file is on the memory card inserted in the slot. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
Troubleshooting TROUBLESHOOTING Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. If problems persist, contact your dealer.
Troubleshooting USB Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
TROUBLESHOOTING Troubleshooting Problem Procedure After making a call you can’t hear a ring Make sure the tone or pulse selection in your communications application is set correctly. You can also use the ATD command. Refer to the chapter on AT commands in online help files for Appendix C, AT Commands. Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval.
Troubleshooting Sleep/Hibernation Procedure The system will not enter Sleep/Hibernation Is Windows Media Player open? The system might not enter Sleep/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Sleep/Hibernation. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
Troubleshooting TROUBLESHOOTING Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth Adpater is installed in the computer. The built-in Bluetooth function and an optional Bluetooth Adpater cannot operate simultaneously.
Troubleshooting TOSHIBA support Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ❑ Review troubleshooting sections in the documentation for software and peripheral devices. ❑ If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions.
TROUBLESHOOTING Troubleshooting Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 China TOSHIBA Personal Computer & Network (Shanghai) Co., Ltd. 43F, Hongkong new world tower, No. 300 Huai Hai Zhong Road, Shanghai, P.R. China 200021 United States of America TOSHIBA America Information Systems, Inc.
Chapter 10 Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. In the text in this manual, +XX is used to show which Disclaimer description is related to TOSHIBA computers. CPU Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in chapter 9 Troubleshooting for more information. 64-Bit Computing. 64-bit processors are designed to take advantage of 32 and 64 bit computing.
Disclaimers After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is a normal phenomenon for all batteries. To purchase a new battery pack, see the accessories information that is shipped with your computer, or visit the Toshiba web site at www.pcsupport.toshiba.com. HDD Drive Capacity 9 1 Gigabyte (GB) means 10 = 1,000,000,000 bytes using powers of 10.
Disclaimers [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed. Non-applicable Icons DISCLAIMERS Certain notebook chassis are designed to accommodate all possible configurations for an entire product series.
Appendixes Appendix A Specifications..................................................................................... A-1 Appendix B Display Controller and Modes .......................................................... B-1 Appendix C V.90/V.92 .............................................................................................. C-1 Appendix D Wireless LAN ...................................................................................... D-1 Appendix E AC Power Cord and Connectors ........
APPENDIXES 1-2 User’s Manual
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 362 (w) x 267.8 (d) x 33.5 (front) / 39.3 (rear) millimeters Weight (typical*) < 3 kilograms, configured with: 15.4" panel, DVD Combo drive, 6-cell battery, and modem. * Weight will vary depending on whether or not and what kind of options are adopted.
Specifications Built-in Modem The ability of this feature is depending on the model you purchased. Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Communication protocol APPENDIX A Communication speed Error correcting Data compression A-2 Data: Full duplex Fax: Half duplex Data ITU-T-Rec V.21/V.22/V.
Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
APPENDIX B Video Modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C V.90/V.92 NOTE: V.90 rates can be achieved only when one V.90 capable modem is connected to another. The TOSHIBA Internal modem will select automatically V.34 if the remote modem lacks V.90 capability or if a combination of network and/or phone line conditions prevent V.90 connection. V.90/V.92 mode Function Transmission speed Data V.90/V.92 From 56K (maximum) to 28Kbps (minimum) Reception only User’s Manual C-1 APPENDIX C The TOSHIBA internal modem uses V.90 technology.
APPENDIX C Table E-1 Result codes for a V.90 connection No.
AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX C C-4 User’s Manual
Appendix D Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications ■ Mini Card Compatibility ■ ■ IEEE 802.11 Standard for Wireless LANs Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
R-F Frequency Band 5 GHz (5150-5850 MHz) (Revision A, Draft N) ■ Band 2.4 GHz (2400-2483.5 MHz) (Revision B, G, Draft N) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. ◆ The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required. ◆ In a Wireless LAN Access Point, the Wireless LAN card will use the factoryset default channel(printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device. Wireless IEEE 802.
Frequency Range Channel ID 5150-5850 MHz Note *3 128 5640 132 5660*3 136 5680*3 140 5700*3 149 5745*3 US only*4 153 5765*3 US only*4 157 5785*3 US only*4 161 5805*3 US only*4 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. *3 These channels are available to A/B/G combo type only. *4 Available Area: US (USA, CANADA) only.
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/ region in which it is used. All cords must meet the following specifications: Length: Minimum 1.8 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia, Europe and China.
The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
SCSI (Abbreviations continued) GLOSSARY SCSI: small computer system interface SIO: serial input/output SO-DIMM: small-outline dual in-line memory module SVGA: super video graphics adapter SDRAM: synchronized dynamic random access memory TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRM: video ready modem VRT: voltage reduction technology A adapter: A device that provides an inter
Byte B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. See also AUTOEXEC.BAT. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on.
cache memory GLOSSARY C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. card: Synonym for board. See board.
Definition compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
delete GLOSSARY delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
hertz format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. folder: An icon in Windows used to store documents or other folders.
GLOSSARY hexadecimal hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer. hot dock/undock: Connecting or disconnecting a device to or from the computer while the computer’s power is turned on.
modem KB: See kilobyte. kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte and megabit. M main board: See motherboard. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720x350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. level 2 cache: See cache.
GLOSSARY monitor monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
RAM password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject. pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/ or main memory such as a printer or a mouse.
GLOSSARY restart restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. RCA jack: A single-pin connector that carries composite video signals, which include both contrast and color information. See also S-video. RGB: Red, green, and blue.
write protection synchronous: Having a constant time interval between successive bits, characters or events. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk. T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output.
GLOSSARY Glossary-14 User’s Manual
Index A B Battery pack 6-5 additional 8-12 location 2-6 replacing 6-13 Battery, See also Battery pack charging 6-8 extending life 6-12 indicator 2-10, 6-3, 6-4 monitoring capacity 6-10 real time clock 6-5 safety precautions 6-6 types 6-4 C CD-RW/DVD drive 1-4, 4-17 Cleaning the computer 4-40 COM level, see Ports, serial D DC IN indicator 2-10, 6-3 Disk indicator 2-10 Display 1-6, 2-7 automatic power off 1-10 opening 3-3 See also Video modes and Monitor external selection, See Hot keys User’s Manual 1-1
Index INDEX H temporarily using overlay (overlay off) 5-8 turning on 5-6 Windows special keys 5-6 Hard disk drive 1-4 automatic power off 1-10 problems 9-8 Hibernation 1-11, 5-4 problems 9-21 Hot keys 1-10, 5-3 display brightness 5-4 display selection 5-4 hibernation 5-4 lock computer mode 5-4 power save mode 5-4 sleep 5-4 standby 5-4 HW Setup 1-12, 1-13 accessing 7-1 Boot Priority 7-4 CPU 7-4 Display 7-3 General 7-2 Keyboard 7-6 LAN 7-6 Password 7-2 USB 7-6 L LAN, See also Wireless LAN 1-8 cable types
Index P 3 keyboard 9-7 LAN 9-21 LCD panel 9-7 modem 9-19 monitor, external password 9-7 PC card 9-16 User’s Manual 9-17 R Real time clock battery, See Battery Recovery Media 3-12 S Screen, See Display ScrLock (Fn + F12), See Soft keys Security lock 1-9 attaching 8-15 location 2-4 Self Test, See Problems Serial port, See Ports, serial adaptor 1-16, 2-15, 8-12 options 1-16 Sleep 1-11 Soft keys 5-2 cursor control mode 5-2, 5-3 Enter 5-3 numeric mode 5-2 right Alt key 5-3 right Ctrl key 5-3 ScrLock 5-3 Sou
Index U Utilities list 1-12 USB 1-7 location 2-3, 2-4 problems 9-19 using 4-36 V INDEX Video modes, Appendix B Video RAM 1-3 Video-out jack 1-7, 2-3 Volume control, See Sound system W Wireless LAN 1-8 using 4-36 Index-4 User’s Manual
