SHTA Owner’s manual Manuel de l’utilisateur Bedienungsanleitung Manual del propietario Uso e manutenzione
SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated on the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly.
SECTION DE MESSAGE SPÉCIAL INSCRIPTIONS DE SÉCURITÉ DU PRODUIT: Les produits électroniques Yamaha peuvent comporter des étiquettes semblables aux représentations graphiques indiquées ci-dessous ou fac-similés moulés/ estampés de ces représentations graphiques sur l’encoffrement. L’explication de ces représentations graphiques apparaît à cette page. Veuillez respecter toutes les précautions indiquées à cette page et celles indiquées dans la section des directives de sécurité.
IMPORTANT SAFETY INSTRUCTIONS WARNING — When using any electrical or electronic product, basic precautions should always be followed. These precautions include, but are not limited to, the following: 1. 2. 3. 4. 5. 6. 7. Read these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES AVERTISSEMENT — Lors de l’utilisation de n’importe quel appareil électrique ou électronique, les précautions fondamentales devraient toujours être suivies. Ces précautions comprennent, mais ne sont pas limitées à, ce qui suit: 1. 2. 3. 4. 5. 6. 7. Lisez ces directives. 8.
IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT: THE WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes. Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.
English SHTA Owner’s manual
Important Precautions Read the following before operating the TransAcoustic™ piano. ■■Warnings ■■Cautions • Do not locate the TransAcoustic piano in a place subject to excessive heat, low temperatures, or direct sunlight. This could be a fire hazard and may damage the finish and internal parts. • Turn off all audio devices when connecting to the TransAcoustic piano. Refer to the user’s guide for each device. Use the correct cables and connect as specified.
Introduction Features Yamaha’s Innovative Silencing System • The hammer shank stopper stops the movement of the hammer just before striking the string, and the optical sensor will catch keystroke information precisely. The internal tone generator receives the keystroke information and reproduces enrich sound of the piano. • The noncontact optical sensor faithfully detects subtle movement of the keys without affecting the touch of the keys. You can enjoy the natural expression of the music.
Introduction TransAcoustic™ Technology and TA Mode New Yamaha Technology: TransAcoustic™ • Acoustic pianos utilize a mechanism in which hammers strike the strings, and the vibrations from the strings are then transmitted to a soundboard which emits sound. The idea of using a vibration speaker to vibrate the soundboard is not new in the piano world, and actually dates back to the 1990s. • To date, piano manufacturers from around the world have released pianos with vibration speakers attached.
Introduction Accessories Check that the following items are supplied with your piano. Headphones × 1 Headphones hanger × 1 Attachment screws for headphones hanger × 2 Owner’s manual × 1 Music book “50 greats for the Piano” × 1 Installation Avoid placing this instrument in direct sunlight, in close proximity to heating equipment or other high temperature areas, or in locations with a high degree of humidity. Avoid placing this instrument in dusty or dirty areas.
Introduction Table of Contents Chapter 1 Chapter Getting Started �����������������������������������������7 6 Connecting to Audio Devices ��������������������������35 Connecting to MIDI Devices ���������������������������37 Connecting the USB Storage Device ���������������38 Connecting Powered Speakers [for Grand Piano] ���������������������������������������������39 Part Names and Functions ���������������������������������7 Connecting the AC Power Cable ���������������������10 Attaching the Headpho
Chapter 1 Getting Started Part Names and Functions English ■■ Piano Upright piano Grand piano 1 AC inlet unit (on the rear of the piano) Control unit (page 8) 1 Amplifier unit (page 9) Control unit (page 8) Silencing lever [For models equipped with a sostenuto pedal] Activates the Silent Piano™ function (page 13). ■■ Pedals Upright piano 1 1 Grand piano 2 3 Soft pedal / shift pedal 1 2 Reduces the volume and slightly changes the timbre notes played after the pedal is pressed.
Chapter 1 Getting Started Part Names and Functions ■■ Control unit (front panel) Upright piano 1 2 3 4 5 10 6 7 11 8 9 12 Grand piano 1 2 3 4 5 10 1 POWER 6 7 11 button 8 9 12 7 Turns the TransAcoustic piano on and off. 2 FUNC. button Switches the function. The function will be switched as follows each time you press this button. PIANO button [For upright pianos] Switches the voice of the TransAcoustic piano to the Piano voice.
Chapter Getting Started 1 Part Names and Functions ■■ Control unit (bottom panel) 13 14 English 13 MIDI IN/MIDI OUT jacks Connect to the input or output jacks of external MIDI devices. 14 AUX IN/AUX OUT jacks (stereo mini jack) Connect to the input or output jacks of external audio devices. ■■ Amplifier unit [for grand piano] 1 OUTPUT 2 L(L+R) 1 OUTPUT L (L+R)/R jacks (TRS phone jack) Connect the optional powered speakers (page 39). 2 R MIN VOL. MAX OUTPUT VOL.
Chapter 1 Getting Started Connecting the AC Power Cable 1 Connect the AC power cable extending from the piano to the AC wall outlet. Upright piano Grand piano Warning Use the AC power cable attached to the piano. Use of other AC power cables may result in damage, overheating, or fire. Caution • Do not stretch the cable or bend its ends. • Do not attempt to use the cable if it is stretched or if the ends of the cable have been bent. Attempting to do so may cause interruptions to the power supply.
Chapter Getting Started 1 Attaching the Headphones Hanger Attach the hanger to the underside of the control unit with the two screws supplied. English Screwdriver Turning the Power On 1 Press the POWER button. The POWER lamp lights up. The display shows the voice number “1” (Piano). The TransAcoustic piano is now ready for use. Note • The sound is not output properly if you hold down the keyboard while turning the power on. Remove your hand from the keyboard when turning the power on.
Chapter 2 Playing the Piano Playing with the TA Mode 1 [For upright pianos not equipped with a sostenuto pedal] Press the center pedal and slide it to the left. [For upright pianos equipped with a sostenuto pedal] Pull the silencing lever towards you until you hear a click and feel the mechanism catch. [For grand pianos] Press the QUIET button. The QUIET lamp lights up.
Chapter Playing the Piano 2 Using the Silent Piano™ Function 1 [For upright pianos not equipped with a sostenuto pedal] Press the center pedal and slide it to the left. Pull the silencing lever towards you until you hear a click and feel the mechanism catch. [For grand pianos] Press the QUIET button. The QUIET lamp lights up. Note [For grand pianos] The QUIET lamp lights up immediately after turning the power on. In that case, this operation is unnecessary.
Chapter 2 Playing the Piano Selecting Voices When using the TA mode or the Silent Piano™ function, you can use the internal voices of this unit to perform with voices other than that of a piano. 1 Press the FUNC. button repeatedly to switch the function to VOICE. The number of the currently selected voice appears on the display. 2 Press the +/YES or –/NO button to select the desired voice. Voice Explanation Off The unit does not use any voices.
Chapter Playing the Piano 2 Selecting Voices ■■ Using voice variations The unit provides “voice variations” (alternate versions with effect) for your enjoyment when playing other voices than Piano. Press the soft/shift pedal to alter the sound of the voice. When you select the Electric Piano voice: The pedal switches between on and off of the chorus effect. Upright piano Grand piano When you select the Vibraphone voice: The pedal switches between on and off of the vibrato.
Chapter 2 Playing the Piano Applying the Reverb Effect A piano sounds differently depending on the size of the room, or the material of the building in which it is played. The reverberation is the major reason for this difference. Using the reverb functions and simulating the reverberation in a concert hall, gives you the feeling of the being at a live performance. 1 Press the FUNC. button repeatedly to switch the function to REVERB. The current depth setting appears on the display. 2 Hold the FUNC.
Chapter Playing the Piano 3 Using the Metronome The unit features the built-in metronome that helps you to play at the accurate tempo. 1 English Press the FUNC. button repeatedly to switch the function to METRO. The current tempo setting appears on the display. 2 Press the PLAY/PAUSE button to start the metronome. 3 Press the +/YES or –/NO button to change the tempo. You can change the tempo in the range of 5 to 500 (bpm).
Chapter 3 Playing Back Songs Songs You Can Play on This Unit The unit can play the preset songs, songs you recorded, or commercially available songs. In this manual, they are collectively called “songs.” You can simply listen to these songs, but also practice playing along with the song playback. ■■ Playable song data format Song Format File Format MIDI song In a MIDI song, the information of your keyboard performance (such as keystroke and velocity) is recorded.
Chapter Playing Back Songs 3 Playing Back the Demonstration Song You can play back any of the demonstration songs stored in this unit. 1 English Press the FUNC. button repeatedly to switch the function to SONG. The song number of the currently selected category appears on the display. 2 Hold the FUNC. button for a second to switch to the song category selection display. Hold The currently selected song category blinks on the display. 3 Press the +/YES or –/NO button to select “d.
Chapter 3 Playing Back Songs Playing Back the Preset Song Besides the demonstration songs, 50 piano songs are preset in this unit. These correspond to the score in the music book “50 greats for the Piano.” This will help you to practice playing along with the song playback. 1 Press the FUNC. button repeatedly to switch the function to SONG. The song number of the currently selected category appears on the display. 2 Hold the FUNC. button for a second to switch to the song category selection display.
Chapter Playing Back Songs 3 Playing Back the Song Recorded on the Internal Memory Your performance that has been recorded as a MIDI song and saved on the internal memory can also be played back. Note 1 English To record your performance, see “Recording Your Performance on the Internal Memory” on page 26. Press the FUNC. button repeatedly to switch the function to SONG. The song number of the currently selected category appears on the display. 2 Hold the FUNC.
Chapter 3 Playing Back Songs Playing Back the Song Saved on the USB Storage Device Connecting commercially available USB storage device to the unit allows you to play back songs stored on that device. 1 Connect the USB storage device to the USB port at the front of the control unit. For details, see “Connecting the USB Storage Device” on page 38. 2 Press the FUNC. button repeatedly to switch the function to SONG. The song number of the currently selected category appears on the display.
Chapter Playing Back Songs 6 Playing Back the Song Saved on the USB Storage Device Press the +/YES or –/NO button to select the desired song number. English Song Number Explanation S.00 – S.99 F.00 – F.99 100 – 399 A.00 – A.99 Plays back only the selected song. When the playback advanced to the end of the selected song, playback stops. C.00 – C.99 100 – 399 Random playback All playback Plays back all songs in the selected category continuously in random order.
Chapter 3 Playing Back Songs Operations during Playback Pause Stop Move to the previous/next song Fast-forward/rewind (Hold) ■■ Pausing playback You can pause playback and restart it from where the song was paused. Press the PLAY/PAUSE button during playback. While playback is paused, the PLAY/PAUSE lamp blinks. Press the PLAY/PAUSE button to restart playback again. ■■ Stopping playback You can stop playback and start it from the beginning of the song. Press the STOP button during playback.
Chapter Playing Back Songs 3 Changing the Playback Tempo You can speed up or slow down the playback tempo. Slowing down the playback tempo can be useful when practicing a difficult piano part. During playback or pause, hold the FUNC. button for a second to switch to the tempo setting display. Hold The current tempo setting blinks on the display. 2 Press the +/YES or –/NO button to adjust the tempo. You can adjust the playback tempo in the range of –50 to +50 (%).
Chapter 4 Recording Your Performance Recording Your Performance on the Internal Memory You can record your performance on the internal memory of the unit. Recorded performances are saved as a MIDI song (SMF0). Note • You can record up to 10 songs on the internal memory. • You can record up to approximately 500 KB, which equates to a standard song of approximately 30 minutes in length, per one recording. • The recorded performances are preserved even if you turn the unit off.
Chapter Recording Your Performance 6 Recording Your Performance on the Internal Memory Press the +/YES and –/NO buttons to select the destination song number. English Note • If you select an empty song (which contains no data), the song number and the blank indication (- - -) appears alternately on the display. • Note that the new recording will erase the existing data if you select a song which contains data. • To cancel recording, press the STOP or REC button. 7 Press the PLAY/PAUSE button.
Chapter 4 Recording Your Performance Recording Your Performance on the USB Storage Device You can record your performance directly on the USB storage device. Recorded performances are saved as a MIDI song (SMF0) or an audio song (USB Audio Recorder, 44.1kHz/16bit stereo WAV). Note • You can record as much as the capacity of the USB storage device allows. • You can record up to approximately 500 KB per one MIDI song recording and up to 80 minutes per one audio song recording.
Chapter Recording Your Performance 7 Recording Your Performance on the USB Storage Device Press the +/YES or –/NO button to select the destination song number. English Note • If you select an empty song (which contains no data), the song number and the blank indication (- - -) appears alternately on the display. • Note that the new recording will erase the existing data if you select a song which contains data. • To cancel recording, press the STOP or REC button. 8 Press the PLAY/PAUSE button.
Chapter 4 Recording Your Performance Recording with the Metronome You can use the metronome to record performance. 1 Press the FUNC. button repeatedly to switch the function to METRO. The current tempo setting appears on the display. 2 Press the PLAY/PAUSE button to start the metronome. 3 Press the +/YES or –/NO button to change the tempo. You can change the tempo in the range of 5 to 500 (bpm).
Chapter 5 Handling Song Files Copying a Song File to the USB Storage Device Note You can copy only the user song on the internal memory to the USB storage device. 1 Connect the USB storage device to the USB port at the front of the control unit. For details, see “Connecting the USB Storage Device” on page 38. 2 Press the FUNC. button repeatedly to switch the function to SONG. The song number of the currently selected category appears on the display. 3 Hold the FUNC.
Chapter 5 Handling Song Files Copying a Song File to the USB Storage Device 7 Hold the REC button for 3 seconds. “SAv” appears on the display. Then the smallest number of empty song in the USB MIDI user song category and the blank indication (- - -) appears alternately on the display. Note • If there is no empty song in the USB MIDI user song category, “FUL” appears on the display and the song cannot be copied. Delete unnecessary files (page 33) and try again.
Chapter Handling Song Files 5 Deleting a Song File You can delete the user song on the internal memory or the USB storage device. Note You can delete only the user song on the internal memory or the USB storage device. English 1 To delete the song file stored on the USB storage device, connect the USB storage device to the USB port at the front of the control unit. For details, see “Connecting the USB Storage Device” on page 38. 2 Press the FUNC. button repeatedly to switch the function to SONG.
Chapter 5 Handling Song Files Deleting a Song File 7 Hold the REC and STOP buttons simultaneously for 3 seconds. “n-y” and “dEL” appears alternately on the display. Note You cannot delete songs other than user songs. If you try to delete such songs, “E01” or “Pro” appears on the display. 8 Press the +/YES button. Deletion starts. Dashes appear on the display indicating that the selected song is being deleted. If the song is successfully deleted, “End” will appear on the display.
Chapter 6 Connecting to Other Devices Connecting to Audio Devices English Caution Be sure to turn the unit and audio devices off before attempting to connect them. Note The AUX IN or AUX OUT jack on this unit is a stereo mini jack. If your connection cable is not compatible, you will need to use an adaptor. Please use a nonresistant cable and adaptor. ■■ Connecting to the AUX OUT jack When connected to a compo system or IC recorder: You can record performances played using the Silent Piano™ function.
Chapter 6 Connecting to Other Devices Connecting to Audio Devices ■■ Connecting to the AUX IN jack When connected to other sound modules or playback devices (such as CD players): You can use the Silent Piano™ function together with the sound received from the connected devices. Control unit bottom panel To AUX IN jack (stereo mini jack) Other sound modules OR CD player etc. Audio cable Caution Do not route the output from the AUX OUT jack to the AUX IN jack.
Chapter Connecting to Other Devices 6 Connecting to MIDI Devices Caution Be sure to turn the unit and MIDI devices off before attempting to connect them. When connected to other MIDI device: You can reproduce the Silent Piano™ performances using sound modules such as synthesizers and other MIDI devices.
Chapter 6 Connecting to Other Devices Connecting the USB Storage Device Connecting commercially available USB storage device to the unit allows you save your performance, and playback songs stored on the device. Connect the USB storage device into the USB port at the front of the control unit. Caution • Do not remove the USB storage device or turn the unit on or off during data transfer as breakage may result. • Do not insert and remove the USB storage device too frequently as breakage may result.
Chapter Connecting to Other Devices 6 Connecting Powered Speakers [for Grand Piano] The OUTPUT L (L+R)/R jacks let you connect the optional powered speakers. You can also use the OUTPUT VOL. knob to fine-adjust the volume of these jacks. Powered speakers English Amplifier unit OUTPUT L(L+R) R MIN VOL. MAX To OUTPUT jack (TRS phone jack) To audio input jack Audio cable Note • Adjusting the volume with the VOLUME knob also affects the output level of the OUTPUT L (L+R)/R jacks.
Chapter 7 Using Various Functions Setting the Various Convenient Functions (Function Setup) To get the most out of your piano, set some of the various convenient functions, such as fine tuning of the pitch, adjusting the metronome volume, etc.
Chapter Using Various Functions 7 Setting the Various Convenient Functions (Function Setup) ■■ Basic operations 1 English Press the FUNC. button repeatedly to turn off all function indicators. The unit enters the Function Setup mode and the Function Setup item number appears on the display. 2 Press the +/YES or –/NO button to select the desired item. 3 Hold the FUNC. button for a second to switch to the parameter setup display.
Chapter 7 Using Various Functions Details on Each Function Setup Item ■■ Brilliance ■■ FIXED Velocity You can adjust the timbre brilliance of the sound from mellow to bright. You can change the velocity when you select Off (FIXED) in the Touch Sensitivity setting. –2 (mellow) –1 (mellow/normal) Setting 0 range (normal) 1 (normal/bright) 2 (bright) Default setting The unit produces soft and mellow tone. The setting between mellow and normal. The unit produces standard tone.
Chapter Using Various Functions 7 Details on Each Function Setup Item ■■ Base Note Certain genres of music are composed based on scales other than equal temperament, which is the common piano tuning scale. You can enjoy various scales with this setting. You need to specify the root when you select a scale other than equal temperament in the Scale setting. 1 (equal temperament) One octave is divided into twelve equal intervals. Currently the most popular piano tuning scale.
Chapter 7 Using Various Functions Details on Each Function Setup Item ■■ Metronome Volume ■■ Song Transpose You can adjust the volume of the metronome. You can transpose the pitch of song playback (MIDI and audio) or sound input through the AUX IN jack. Transposition can be set in semitone increments. For example, if you set the transposition amount to 5, playing C3 key produces pitch F3.
Chapter Using Various Functions 7 Details on Each Function Setup Item ■■ Key-off Sample Volume You can set the depth of the String Resonance effect. This setting is effective for the Piano voice. You can set the volume of the Key-off Sample. This setting is effective for the Piano voice. Setting range Default setting 0 to 10 5 Setting range Default setting 0 to 10 5 Note Note • The String Resonance does not work in the TA mode.
Chapter 7 Using Various Functions Details on Each Function Setup Item ■■ TA Mode Tone Control (High) ■■ Piano Playback Channel You can adjust the high-frequency range of sounds from the soundboard. You can assign the desired channel that is played back as a piano part when the unit receives the MIDI data. Setting range Default setting –12 to +12 0 Off Note This setting does not revert to its default setting when you turn the unit off.
Chapter Using Various Functions Details on Each Function Setup Item ■■ Auto Power-off You can select whether the unit transmits or receives program change numbers. You can turn the power off automatically if you do not operate the unit for 30 minutes with the auto poweroff function. You can activate or deactivate the auto power-off function. On Off Default setting The unit transmits or receives program change numbers. The unit does not transmit or receive program change numbers.
Chapter 7 Using Various Functions Restoring the Default Settings You can erase the backup of all settings made and restore the factory default settings. 1 While holding the STOP button, press the POWER button to turn the unit on. + “CLr” appears on the display and all settings are reset to factory default. Caution DO NOT turn the unit off while “CLr” appears on the display as may corrupt the data or damage the internal memory. Note The user songs on the internal memory will be retained.
Chapter Using Various Functions 7 Deactivating the Auto Power-off Function 1 While holding the FUNC. button, press the POWER button to turn the unit on. + Note If you deactivate the auto power-off function with this step, “F9 Auto Power-off” in Function Setup (page 47) is automatically set to “Off.” 49 English “PoF” appears on the display and the auto power-off function is deactivated.
Chapter 8 Appendix Messages Message Situation The unit is being initialized to the factory default settings. The song file is not compatible with the unit, or the song file may be damaged. The USB storage device is protected. Remedy DO NOT turn the unit off when “CLr” appears in the display. You cannot select this song file. The capacity of the USB storage device becomes full. Delete unnecessary files on the USB storage device (page 33), or use another USB storage device with sufficient capacity.
Chapter Appendix 8 Troubleshooting If you have problems with the unit, here are a few troubleshooting tips. If you cannot solve the problem easily yourself, consult your Yamaha piano dealer. DO NOT attempt to repair the piano yourself. Cause The AC power cable may not be plugged in correctly. The unit turns on but no sound is heard. The VOLUME knob may be turned to the far left position. The voice is set to Off. The pedal has no effect. The pedal sensor may not be connected correctly.
Chapter 8 Appendix Preset Voice List No. 1 52 Voice Piano 2 Electric Piano 1 3 Electric Piano 2 4 Electric Piano 3 5 Harpsichord 1 6 7 Harpsichord 2 Vibraphone 8 Celesta 9 Pipe Organ 1 10 Pipe Organ 2 11 Pipe Organ 3 12 Pipe Organ 4 13 Jazz Organ 14 15 16 Strings Choir Synth Pad 17 18 19 Piano + Strings Piano + Synth Pad Piano + Electric Piano 1 Explanation This sound was sampled from the Yamaha CFX concert grand piano.
Chapter Appendix 8 Song List ■■ Demonstration songs Title Polonaise op.53 “Héroïque” Piano Sonate No.18 K.576 1st mov. “Little Overture” from The Nutcracker op.71a ■■ Preset songs No. P.01 P.02 P.03 P.04 P.05 P.06 P.07 P.08 P.09 P.10 P.11 P.12 P.13 P.14 P.15 P.16 P.17 P.18 P.19 P.20 P.21 P.22 P.23 P.24 P.25 Title Invention No.1 Invention No.8 Gavotte Prelude (Wohltemperierte Klavier I No.
Chapter 8 Appendix Playback Sequence of Song Files on the USB Storage Device The illustration below shows the playback sequence of song files stored on the USB storage device. USB storage device First level Folder A Second level Third level Fourth level Sub Folder A Sub Folder A Sub Folder A AAA.mid AAA.mid AAA.mid General folders BBB.mid Folder B Sub Folder B AAA.mid No playback occurs. AAA.mid BBB.mid USER FILES PIANODIR.FIL Administrative files PPFile1 PPFile2 AAA.
Chapter Appendix 8 Specifications Pedals Key Sensor Hammer Sensor Pedal Sensors Damper Pedal Sostenuto Pedal Soft/Shift Pedal Silencing System Mechanism Soundboard Drive System Internal Tone Action Mechanism Digital Tone Type Sound Engine (Piano) Piano Effects Polyphony (max.
Chapter 8 Appendix Index A P Accessory.............................................................................................5 AC Power Cable................................................................................10 Administrative file.............................................................................54 All playback.....................................................................19, 20, 21, 23 Amplifier unit....................................................................
SHTA Data list Data list
XG Voice List Voice Group Piano Chromatic Percussion Organ Voice Name GrandPiano GrndPianoKSP MellowGrPno PianoStrings Dream BrightPiano BritePnoKSP ElecGrandPno ElecGrPnoKSP DetunedCP80 LayeredCP1 LayeredCP2 Honkytonk HonkytonkKSP El.Piano1 El.Piano1KSP MellowEP1 ChorusEP1 HardEl.Piano VXfadeEl.P1 60sEl.Piano1 El.Piano2 El.Piano2KSP ChorusEP2 DXEPHard DXLegend DXPhaseEP DX+AnalogEP DXKotoEP VXfadeEl.P2 Harpsichord Harpsi.KSP Harpsichord2 Harpsichord3 Clavi. Clavi.KSP Clavi.Wah PulseClavi. PierceClavi.
Voice Group Bass Strings Ensemble Brass XG Voice List MSB 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 LSB 40 64 65 66 96 0 6 12 18 19 32 40 41 64 0 8 0 0 0 0 8 40 0 0 40 0 0 3 8 24 35 40 41 42 45 0 3 8 40 41 64 65 0 27 64 65 0 0 3 16 32 40 0 0 40 41 64 0 35 64 0 16 17 32 0 18 0 16 0 0 6 32 37 0 35 40 41 42 0 12 20 24 PRG 39 39 39 39 39 40 40 40 40 40 40 40 40 40 41 41 42 43 44 45 4
XG Voice List Voice Group Synth. Pad Synth. Effects Ethnic D4 Voice Name Itopia CCPad BowedPad Glacier GlassPad MetallicPad TinePad PanPad HaloPad SweepPad Shwimmer Converge PolarPad Celestial Rain ClaviPad HarmoRain AfricanWind Carib SoundTrack Prologue Ancestral Crystal SynthDr.Comp Popcorn TinyBells RoundGlocken GlockenChime ClearBells ChorusBells SynthMallet SoftCrystal LoudGlocken ChristmasBel VibeBells DigitalBells AirBells BellHarp Gamelimba Atmosphere WarmAtmos.
XG Drum Kit List : Same as Standard Kit 1 : No Sound 127 0 25 26 Analog Kit Reverse Cymbal Hi Q 2 Snare Noisy 4 Kick 3 Kick Analog Short Kick Analog Side Stick Analog Snare Analog Snare Analog 2 Tom Analog 1 Hi-Hat Closed Analog Tom Analog 2 Hi-Hat Closed Analog 2 Tom Analog 3 Hi-Hat Open Analog Tom Analog 4 Tom Analog 5 Crash Analog Tom Analog 6 Cowbell Analog Conga Analog H Conga Analog M Conga Analog L Maracas 2 Claves 2 Scratch H 2 Scratch L 2 D5 Data list Bank Select MSB (0-127) 127 127 127 1
XG Drum Kit List : Same as Standard Kit 1 : No Sound Bank Select MSB (0-127) 127 127 127 127 126 Bank Select LSB (0-127) 0 0 0 0 0 Program Change (0-127) 27 32 40 48 0 Program Change (1-128) 28 33 41 49 1 MIDI Alternate Dance Kit Jazz Kit Brush Kit Symphony Kit SFX Kit1 Key Off Group Note # Note 13 C#-1 3 14 D-1 3 15 D#-1 16 E-1 17 F-1 4 18 F#-1 4 19 G-1 20 G#-1 21 A-1 22 A#-1 23 B-1 24 C0 25 C#0 26 D0 27 D#0 Reverse Cymbal 28 E0 29 F0 30 F#0 Hi Q 2 31 G0 Snare Techno Snare Jazz H Brush Slap 2 32 G#0 33 A0
MIDI Data Format Preset Voice List Voice Name Piano Electric Piano 1 Electric Piano 2 Electric Piano 3 Harpsichord 1 Harpsichord 2 Vibraphone Celesta Pipe Organ 1 Pipe Organ 2 Pipe Organ 3 Pipe Organ 4 Jazz Organ Strings Choir Synth Pad Bank MSB 108 108 108 108 108 108 108 108 108 108 108 108 108 108 108 108 LSB 0 0 0 1 0 1 0 0 1 0 2 3 0 0 0 0 Program Change (0 – 127) 0 5 4 4 6 6 11 8 19 19 19 19 16 48 52 89 * Dual voices (Piano + Strings, Piano + Synth Pad, Piano + Electric Piano 1) cannot be recalled
MIDI Data Format MIDI Channel Message (1) Status byte MIDI Events Key Off [GM1] [GM2] Key On [GM1] [GM2] Control Change Status 8nH 9nH (n: Channel Number) (n: Channel Number) BnH 1st Data byte Data kk kk 0 (00H) 1 (01H) 5 (05H) 6 (06H) 7 (07H) 10 (0AH) (n: Channel Number) 97 (61H) RPN Decrement 98 99 100 (62H) (63H) (64H) 101 (65H) 120 (78H) 121 (79H) 122 (7AH) NRPN LSB NRPN MSB RPN LSB [GM2] RPN MSB [GM2] All Sound Off [GM2] Reset All Controllers [GM1] [GM2] Local Control (4
MIDI Data Format MIDI Channel Message (2) ■■ Parameters Controlled by NRPN (Non-Registered Parameter Numbers) NRPN Data Entry Parameter MSB LSB MSB LSB 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 14H 08H 09H 0AH 20H 21H 30H 31H 34H 35H 63H 64H 66H rrH mmH mmH mmH mmH mmH mmH mmH mmH mmH mmH mmH mmH mmH — — — — — — — — — — — — — Vibrato Rate Vibrato Depth Vibrato Delay Low Pass Filter Cutoff Frequency Low Pass Filter Resonance EQ BASS EQ TREBLE EQ BASS Frequency EQ TREBLE Frequency EG Attac
MIDI Data Format MIDI Parameter Change Table ■■ MIDI Parameter Change Table (XG SYSTEM) Address (H) 00 00 Size Data (H) (H) Parameter 00 4 00-0F MASTER TUNE 00-0F 00-0F 00-0F 04 05 06 7D 7E 7F TOTAL SIZE 1 1 1 1 1 1 07 00-7F 00-7F 28-58 N 00 00 MASTER VOLUME MASTER ATTENUATOR TRANSPOSE DRUM SETUP RESET XG SYSTEM ON ALL PARAMETER RESET XG Default (H) Description -102.4…0…+102.
MIDI Data Format MIDI Parameter Change Table Address (H) 02 01 Size Data (H) (H) Description [ MIDI (Silent) ] MIDI Reception MIDI Transmission Piano Song Panel Song MIDI Playback Part Operation Playback Input Channel × × × (Voice Setting) × × × (Voice Setting) × × × × × × × (Voice Setting) × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × 20 2 00-7F CHORUS TYPE MSB 00-7F CHORUS TYPE LSB Refer to Effect Parameter List 41(=CHORUS1) 00 22 1 00-7F CHORUS PARAMETER 1 Refer to E
MIDI Data Format MIDI Parameter Change Table ■■ MIDI Parameter Change Table (MULTI EQ) Address (H) 02 Size Data (H) (H) 40 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 TOTAL SIZE Parameter 1 00-04 EQ TYPE 1 34-4C EQ GAIN1 1 04-28 EQ FREQUENCY1 1 01-78 EQ Q1 1 00-01 EQ SHAPE1 1 34-4C EQ GAIN2 1 0E-36 EQ FREQUENCY2 1 01-78 EQ Q2 1 NOT USED 1 34-4C EQ GAIN3 1 0E-36 EQ FREQUENCY3 1 01-78 EQ Q3 1 NOT USED 1 34-4C EQ GAIN4 1 0E-36 EQ FREQUENCY4 1 01-78 EQ Q4 1 NOT USED 1 34-4C EQ GAIN5 1
MIDI Data Format MIDI Parameter Change Table ■■ MIDI Parameter Change Table (MULTI PART) Address (H) 08 nn Size Data (H) (H) 00 01 02 03 04 1 1 1 1 1 05 06 1 1 00-20 00-7F 00-7F 00-7F 00-0F, 7F 00-01 00-02 Parameter NOT USED BANK SELECT MSB BANK SELECT LSB PROGRAM NUMBER Rcv CHANNEL MONO/POLY MODE SAME NOTE NUMBER KEY ON ASSIGN 00-03 PART MODE XG Default (H) Description [ MIDI (Silent) ] MIDI Reception MIDI Transmission Piano Panel Song MIDI Song Playback Operation Playback Input Part Cha
MIDI Data Format MIDI Parameter Change Table Address (H) Size Data (H) (H) Parameter 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E TOTAL SIZE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-5F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-5F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-01 00-7F 00-7F 00-7F 00-7F 00-7F 01-7F 01-7F 70 71 72 73 TOTAL SIZE 1 1 1 1 04 NOT USED NOT USED 00-7F EQ BASS GAIN 00-7F EQ TREBLE GAIN 74
MIDI Data Format MIDI Parameter Change Table ■■ MIDI Parameter Change Table (DRUM SETUP) Address (H) 3n rr Size Data (H) (H) Parameter 00 01 02 03 04 05 06 07 08 09 0A 0B 1 1 1 1 1 1 1 1 1 1 1 1 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-01 00-01 00-01 00-7F PITCH COARSE PITCH FINE LEVEL ALTERNATE GROUP PAN REVERB SEND CHORUS SEND VARIATION SEND KEY ASSIGN Rcv NOTE OFF Rcv NOTE ON LOW PASS FILTER CUTOFF FREQUENCY LOW PASS FILTER RESONANCE EG ATTACK RATE EG DECAY1 RATE EG DECAY2 RATE
MIDI Data Format System Exclusive Messages (1) * Not received when Receive System Exclusive Message is set to off. * Not transmitted when Transmit System Exclusive Message is set to off.
MIDI Data Format System Exclusive Messages (2) ■■ System Exclusive Messages (Others) MIDI Event MIDI Master Tuning Data Format F0 43 1n 27 11110000 01000011 0001nnnn 00100111 00110000 00000000 00000000 0000mmmm 0000llll 0ccccccc 11110111 30 F0 43 1n 27 30 00 00 0m 0l cc F7 00 00 mm ll cc F7 = Exclusive status = YAMAHA ID n= always 0(when transmit), n=0-F(when receive) = Model ID of TG100 = Address High = Address Mid = Address Low = Master Tune MSB = Master Tune LSB = don’t care = End of Exclusiv
MIDI IMPLEMENTATION CHART YAMAHA Model: TransAcoustic SHTA Basic Channel Mode Date: 07-June-2012 Version: 1.00 Function...
Copyright © 2014 Yamaha Corporation P.O.
