English Deutsch L2 SWITCH Español Français SWR2311P-10G Русский Italiano Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manuale di istruzioni Руководство пользователя EN DE FR ES IT RU
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. • Only use the voltage specified as correct for the product. The required voltage is printed on the name plate of the product. WARNING • Use only the supplied power cord/plug. If you intend to use the product in an area other than in the one you purchased, the included power cord may not be compatible. Please check with your Yamaha dealer.
Location and connection • This product contains no user-serviceable parts. Do not attempt to disassemble the internal parts or modify them in any way. • Do not place the product in an unstable position where it might accidentally fall over and cause injuries. Water warning • Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings.
possibly causing damage to the product(s), malfunction, or even fire. • Do not place the product in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. • Before moving the product, remove all connected cables. • Always consult qualified Yamaha service personnel if the product installation requires construction work, and make sure to observe the following precautions.
Handling and maintenance • Do not connect any noise generating devices on the same power line as the product. Failure to observe this precaution could result in a malfunction or damage to the product. • Do not touch any port with your fingers or anything metallic. Failure to observe this precaution could result in damage to the product. • Do not locate any connected LAN cables close to the power cord. Otherwise, high voltage might be induced, resulting in malfunction.
Data maintained by the backup battery: • Time information. About disposal About functions/data bundled with the product • This product contains recyclable components. When disposing of this product, please contact the appropriate local authorities. • This is a class A product. Operation of this product in a residential environment could cause radio interference. Open Source Software Used in this Product About this manual • Please refer to Yamaha Pro Audio website for the details of licensing article.
PRECAUTIONS ......................................................................................................... 4 NOTICE ..................................................................................................................... 7 Introduction .............................................................................................................10 Features...................................................................................................................
Introduction Introduction Thank you for purchasing the Yamaha SWR2311P-10G intelligent L2 switch. This product supplies power to PoE powered devices on the network. This owner’s manual is intended for installers and facility designers, and explains installation methods and settings. Please be sure to read this manual before you start using the product to take full advantage of its features. Please retain this manual in a safe location for future reference.
Controls and Connectors English Controls and Connectors Front Panel 9 1 2 3 4 5 6 7 8 1 POWER indicator Lights when power is provided to the unit. POWER indicator Status Unlit Power off Flashing (green) Power on, starting up Lit (green) Power on, normal Lit (orange) Power on, error occurred Caution When one of the following problems occurs, the POWER indicator is lit orange. Verify the status of the problem, and take the appropriate action.
Controls and Connectors 3 RJ-45 CONSOLE port This is an RJ-45 port for making settings. Use an RJ-45/DB-9 console cable to connect it to the RS-232C connector (COM port) of the computer. Use an RJ-45/DB-9 serial cable that is wired as described in “Appendix.” 4 microSD indicator Indicates the connected and operating status of the microSD card. microSD indicator Status Unlit No microSD card is inserted in the slot. Flashing (green) The microSD card is being accessed.
English Controls and Connectors Caution Do not connect a cable to both the LAN port and the SFP port of the same port number. Doing so might cause a malfunction. 9 Cooling vents External air is taken in through these cooling vents. Warning Do not block the cooling vents or place objects near them. Doing so could cause fire or malfunctions. Top panel 9 Serial number MAC address 0 0 Product label This lists the model name, serial number, and MAC address etc. of this unit.
Controls and Connectors Rear panel A Serial number B C A Power cord clamp attachment holes The included power cord clamp (C-shaped) can be attached here. Refer to “Connecting the power cord” (page 32) for information on how to install the unit. B Fans These forcibly exhaust the heat that is generated inside the unit. When a problem is detected, the POWER indicator is lit orange. Caution Do not block the fan vents or place objects near them. Doing so could cause fire or malfunctions.
Controls and Connectors English Bottom panel D F E F D D Leg attachment guides These indicate the locations at which the legs are to be attached when the unit is installed in a horizontal position. If the unit is to be installed in a horizontal position, attach the included legs as shown in the illustration. Leg Leg Leg attachment guides E Rack mount accessory attachment holes Use these holes to attach the RK-SWR rack mount accessory.
Controls and Connectors F Wall mount accessory attachment holes Use these holes to attach the WK-SWR wall mount accessory. Refer to “Installation on a wall or ceiling” (page 22) for information on how to install the unit. Switching the display mode Each time you press the MODE button, the display mode of the port indicators is switched. The lit status and color of the upper and lower MODE indicators shows the selected display mode.
Port indicators These are indicators for the LAN ports and SFP ports, and indicate the state of each port in each mode. LAN ports (upper row) Left Indicator SFP ports (upper row) Right Indicator Left Indicator LAN ports (lower row) SFP ports (lower row) Left Indicator Left Indicator Right Indicator Right Indicator Right Indicator ■ LINK/ACT mode The indicators show the link status and connection speed of the LAN port or SFP port.
Controls and Connectors ■ PoE mode Indicates the power supply status. Left indicator Power supply status Unlit Not supplying power. Lit (green) Supplying power. The right indicator is unlit. ■ VLAN mode Indicates the VLAN membership status of the LAN port or SFP port.
Controls and Connectors LAN ports Right indicator Error information English Left indicator Unlit Unlit Normal Flashing (orange) Unlit A loop was detected. The port has been blocked or shut down. Lit (orange) Unlit A fault has occurred in the device receiving power, and power is not being supplied. Flashing (orange) Because the maximum total electrical power that this unit can supply has been exceeded, power supply to this port was stopped.
Installation in a rack Installation in a rack This section explains how to attach an optional RK-SWR rack mount accessory to the unit. Please read before mounting the unit into a rack This unit is warrantied to operate in an ambient temperature range of 0–40 °C. If you install this unit along with other devices into an EIA-standard or JIS-standard rack, the temperature inside the rack may rise due to heat released from the other devices, resulting in poor performance of the unit.
Installation in a rack 1. Attaching the rack mount panel to the unit Rack mount panel English Use two screws (supplied with the rack-mount accessory) to attach and secure the rack mount panel to the bottom panel of the unit. Screws Warning Use only the specified screws that were included. Failure to do so might allow the unit to fall, causing injury or damage. This could also cause electric shock or malfunctions. 2.
Installation on a wall or ceiling Installation on a wall or ceiling Use the separately sold WK-SWR wall mount accessory to install the unit. If attaching this unit to a ceiling, invert the top and bottom of the unit. You will need to obtain six screws that fit the holes described in step 1 and are appropriate for the material and thickness of the wall or ceiling. Carry out the installation completely, all the way to step 7. Warning Do not attach this unit to a ceiling that is higher than 2 meters.
Installation on a wall or ceiling Wall installation methods (two types) English The SWR2311P-10G can be installed on a wall in the following two ways. Warning Do not install with the LAN ports facing upward or downward. Doing so could cause fire or malfunctions. LAN port side LAN port side 2. Provisionally attach four commercially available screws to the locations that you marked in step 1.
Installation on a wall or ceiling 4. Using four screws included with the mounting accessory, attach it to the SWR2311P-10G. Fasten it securely. Warning • Use only the specified screws that were included. If the unit falls, injury or damage might occur. This could also cause electric shock or malfunctions. • Take care when letting your hand or finger contact the corners of the mounting accessory. Inattention might cause injury.
Settings English Settings Settings for this unit can be made in the following ways. • Make settings using the Web GUI • Make settings from the command line using the CONSOLE port • Make settings from the command line using Telnet • Make settings from the command line using SSH This document explains “Making settings using the Web GUI” (page 26) and “Making settings from the command line using the CONSOLE port” (page 27). You can log in to this unit either as a standard user or as an administrative user.
Settings Making settings using the Web GUI Here we explain the procedure for logging in to this unit using the Web GUI. You will use Yamaha LAN Monitor to log in to the Web GUI, so install Yamaha LAN Monitor before you continue. Before you log in, connect your computer to the same network. If the date and time are incorrect, set the date and time either in the Web GUI’s “Management” tab - “Device settings” page. For details on supported web browsers, refer to the Yamaha Pro Audio website. https://www.
Settings English Making settings from the command line using the CONSOLE port Here we explain the cable, driver, software, and settings that are necessary in order to use the CONSOLE port. If the date and time are incorrect, set the date and time either in “clock set” command / “clock timezone” command. For details on the commands used by this unit, refer to the Command Reference. The Command Reference is available on the Yamaha Pro Audio website. https://www.yamahaproaudio.
Settings ■ Logging in from a computer connected to the CONSOLE port 1. Using a console cable, connect this unit to the computer. Connect the computer to the CONSOLE port of this unit using a USB cable or an RJ-45/DB9 console cable. Notice • The LAN ports and the RJ-45 CONSOLE port all use the same 8-pin connector. If you connect these wrongly, hardware damage or malfunction might occur. Take care when making connections. • If you use the mini-USB CONSOLE port, do not use a USB hub.
Settings When the password is successfully authenticated, the system will wait for a new password to be entered. Skip to step 6 and change the password. SWR2311P-10G Rev.2.02.24 (Fri Jul 15 09:36:55 2022) Copyright (c) 2022 Yamaha Corporation. All Rights Reserved. Please change the default password for admin. New Password: After changing the initial password for the initial administrative user name: After the password is successfully authenticated, the command prompt appears to enable entering commands.
Connections Connections ■ Connecting network devices, PoE powered devices, or a computer Using LAN cables, connect the LAN port of each device to the LAN ports of this unit. If using fiber optic cables to make connections, install an SFP module in an SFP port. For the installation procedure, refer to “Installing an SFP module” (page 30). Warning If you plan to connect a powered device that complies with the IEEE802.3at standards, use a CAT5e or higher-grade cable.
Connections 3. To the connector, connect a fiber optic cable that is suitable for each module. English Connector Fiber optic cable ■ Removing an SFP module Secure this unit so that it will not move, and while grasping the lever of the SFP module, pull it slowly toward yourself to remove the module from the SFP port. NOTE For details on installation, removal, and points of caution, refer to the “SFP-SWRG-LX SFPSWRG-SX Owner’s Manual” included with the SFP module. 1. Detach the fiber optic cable.
Connections ■ Connecting the power cord 1. Attach the included power cord clamp. Notice • We recommend that you attach the supplied power cord clamp to prevent the power cord from accidentally being disconnected. • This clamp is used only for the supplied power cord. If you use the clamp for other power cords, they might be damaged or might not secure properly. Insert the included clamp from the inside of the holes in the unit. 2.
Initialization This unit can be restored to its factory-set state in the following ways. • Using the Web GUI to restore the factory settings (page 33) • Using the cold start command to restore the factory settings (page 34) • Entering the (uppercase I) key during startup to restore the factory settings (page 35) Notice When restoring the factory settings, note the following points. • All communication is halted immediately after execution.
Initialization 5. After this unit has finished restarting, access the Web GUI once again from Yamaha LAN Monitor. NOTE During restart, the computer on which the Web GUI is open will be unable to communicate with the unit (the status indication of the computer’s network adapter will be “Network cable is not connected”), but the communication status will recover when restart is completed.
■ Entering the (uppercase I) key during startup to restore the factory settings The unit can be restored to its factory settings by entering an uppercase when the unit is starting up. This explanation uses the method of disconnecting and reconnecting the power cord. The procedure is also the same when using the reload command to restart this unit. Notice Here we assume that you are logged in as described in “Logging in from a computer connected to the CONSOLE port” (page 28). 1.
Appendix Appendix Hardware specifications Item Specifications Dimensions (not including protrusions and feet) Weight (without accessories) Power supply voltage and frequency Maximum power consumption Standard LAN ports equipped with PoE supply capability 220 mm (W) x 294 mm (D) x 42.4 mm (H) 2.3 kg AC100-240 V, 50/60 Hz 280 W IEEE 802.
Appendix Storage environment conditions Specifications Ambient temperature -20–50 °C Ambient humidity Category name Energy conservation regulatory items English Item Energy consumption efficiency 10–90%, non-condensing A 1.2 W/(Gbit/s) Maximum effective 10.
Appendix RJ-45/DB-9 console cable pin configuration Console (RS-232C) Signal RJ-45 RTS DTR TxD GND GND RxD DSP* CTS* 1 2 3 4 5 6 7 8 D-SUB 9 9 8 6 2 5 3 7 4 1 * These signals are not used by the SWR2311P-10G. Software license agreement The product firmware revision number can be updated. Updating the firmware revision is considered an indication of agreement to the Yamaha network product software license agreement.
English Index A P Administrative password ..................... 33, 34 Command line........................................... 27 CONSOLE port ......................................... 27 Cooling vents ............................................ 13 Password .................................................. 28 Power cord clamp ..................................... 32 Power cord clamp attachment holes ......... 14 POWER indicator ...................................... 11 Power supply inlet ............
222 SWR2311P-10G Owner’s Manual
Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
Información para usuarios sobre la recogida y eliminación de los equipos antiguos Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos no deben mezclarse con los desperdicios domésticos normales. Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje correspondientes, de acuerdo con la legislación nacional.
ADDRESS LIST NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col. San José Insurgentes, Delegación Benito Juárez, CDMX, C.P. 03900, México Tel: +52-55-5804-0600 BRAZIL Yamaha Musical do Brasil Ltda.
Yamaha Pro Audio global website https://www.yamahaproaudio.com/ Yamaha Downloads https://download.yamaha.