English Deutsch Français L2 SWITCH 칺푷컲졓컪 Português Italiano FR Русский Italiano DE ES PT 中文 使用说明书 EN IT RU ZH KO 묻펂 Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manual de instruções Manuale di istruzioni Руководство пользователя Español SWR2310-28GT SWR2310-18GT SWR2310-10G
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! English FCC INFORMATION (U.S.A.) 3. NOTE: This equipment has been tested This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. This product is an intelligent L2 switch with optimal functionality for Dante. Do not use for any purposes other than the one intended. Those who are unfamiliar with handling or those who can not handle according to this manual such as children, should be supervised by responsible persons to ensure safety.
• This product contains no user-serviceable parts. Do not attempt to disassemble the internal parts or modify them in any way. Water warning/Fire warning • Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. • Never insert or remove an electric plug with wet hands.
Maintenance Backup battery • Remove the power plug from the AC outlet when cleaning the product. • Do not replace the backup battery by yourself. Doing so may cause an explosion and/or damage to the product(s). When the backup battery needs to be replaced, contact your Yamaha dealer and have qualified Yamaha service personnel replace the backup battery. Handling caution • Do not insert your fingers or hands in any gaps or openings on the product (vents, ports, panel, etc.).
English NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. Handling and maintenance • Do not touch the interior of a port with your fingers or any metallic object. Doing so might cause malfunctions.
Saving data About this manual • This unit has a built-in backup battery that maintains time information for the data. When the backup battery runs down, the time information will be initialized, causing incorrect time information to be recorded in the log. If this occurs, contact your dealer or a Yamaha customer service center to have the backup battery replaced. The life span of the backup battery is approximately 10 years, but this may vary depending on the conditions of use.
English Contents PRECAUTIONS ......................................................................................................... 4 NOTICE ..................................................................................................................... 7 Introduction .............................................................................................................10 Included items..........................................................................................................
Introduction Introduction Thank you for purchasing the Yamaha SWR2310-28GT, SWR2310-18GT, or SWR2310-10G intelligent L2 switch. This product is an intelligent L2 switch with optimal functionality for Dante. This owner’s manual is intended for installers and facility designers, and explains installation methods and settings. Please be sure to read this manual before you start using the product to take full advantage of its features. Please retain this manual in a safe location for future reference.
English Introduction Separately sold items • RK-SWR rack mount accessory: This is required when installing the SWR2310-10G in a 19-inch rack. • WK-SWR wall mount accessory: This is required when installing the SWR2310-10G or SWR2310-18GT on a wall or ceiling 2 m or less in height. • SFP-SWRG-SX or SFP-SWRG-LX SPF module: This is required when transmitting via 1000BASE-SX or 1000BASE-LX. • SFP-SWRT-SR or SFP-SWRT-LR SFP+ module: This is required when transmitting via 10GBASE-SR or 10GBASE-LR.
Controls and Connectors Controls and Connectors Front Panel SWR2310-28GT 1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 2 4 6 8 10 12 14 16 18 20 22 24 26 28 23 45 6 7 8 SWR2310-18GT 1 1 3 5 7 9 11 13 15 17 2 4 6 8 10 12 14 16 18 23 45 6 7 SWR2310-10G 1 3 5 7 9 2 4 6 8 10 1 23 45 6 9 1 POWER indicator Lights when power is provided to the unit.
2 mini-USB CONSOLE port This is a mini-USB port for making settings. Use a USB cable to connect it to the USB port of a computer. Use a USB cable equipped with a USB Type A connector and a USB miniB (5-pin) connector. Memo Use a cable that supports data transfer. Charge-only cables cannot be used. 3 RJ-45 CONSOLE port This is an RJ-45 port for making settings. Use an RJ-45/DB-9 console cable to connect it to the RS-232C connector (COM port) of the computer.
Controls and Connectors Bottom panel / rear panel / side panel / top panel ° Bottom panel SWR2310-28GT 0 SWR2310-18GT 0 14 B SWR2310-28GT SWR2310-18GT SWR2310-10G
English Controls and Connectors SWR2310-10G B 0 A 0 Leg attachment guides These indicate the locations at which the included legs are to be attached when the unit is installed in a level location. For details on installation, refer to “Attaching the legs” (page 20) in “Installation.” A Rack mount accessory attachment holes SWR2310-10G Use these holes to attach the RK-SWR rack mount accessory. For details on installation, refer to “Installing in a 19-inch rack” SWR2310-10G (page 21) in “Installation.
Controls and Connectors ° Rear panel SWR2310-28GT Serial number C D SWR2310-18GT C Serial number D SWR2310-10G Serial number C D C Power cord clamp attachment holes The included power cord clamp (C-shaped) can be attached here. For details on installation, refer to “Turning the power on” (page 35) in “Connections.” D Power supply inlet (three-pin connector, C14 type) Insert the included power supply cord here.
English Controls and Connectors ° Side panel SWR2310-28GT E G SWR2310-18GT E G SWR2310-10G G ° Top panel SWR2310-28GT MAC address Serial number F SWR2310-28GT SWR2310-18GT SWR2310-10G 17
Controls and Connectors SWR2310-18GT MAC address Serial number F SWR2310-10G MAC address Serial number F G E Rack mount accessory attachment holes SWR2310-28GT / SWR2310-18GT These are used when installing this product in a 19-inch rack (1U). For details on installation, refer to “Installing in a 19-inch rack” SWR2310-28GT / SWR2310-18GT (page 23) in “Installation.” F Product label This lists the model name, serial number, and MAC address etc. of this unit.
English Controls and Connectors Port indicators These are indicators for the LAN ports and SFP/SFP+ ports, and indicate the state of each port in each mode. LAN ports (upper row) Left Indicator SFP/SFP+ ports (upper row) Right Indicator Left Indicator LAN ports (lower row) SFP/SFP+ ports (lower row) Left Indicator Left Indicator Right Indicator Right Indicator Right Indicator The indicators show the link status and connection speed of the LAN port or SFP/SFP+ port.
Attaching the legs Attaching the legs As shown in the illustration, attach the included legs in the positions of the leg attachment guides, and place the unit on a level location such as a desk. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Leg Leg Leg attachment guides Installation in a rack Please read before mounting the unit into a rack • This unit is warrantied to operate in an ambient temperature range of 0–50 °C.
° Installing in a 19-inch rack SWR2310-10G The SWR2310-10G is installed using an RK-SWR rack mount accessory sold separately by Yamaha. Installation This section explains how to attach the unit in the middle block of a rack mount panel. Even if you plan to attach the unit in the left or right block, follow the procedure below. Notice If the supplied feet have already been attached to the unit, remove them. 1.
Installation in a rack 2. Install the rack mount panel to the 19-inch rack. Using the screws that are included with the 19-inch rack (EIA standard 4 pcs., JIS standard 2 pcs.), fasten this unit to the 19-inch rack. Be sure to tighten the screws so that they will not get loosened.
° Installing in a 19-inch rack SWR2310-28GT / SWR2310-18GT The SWR2310-28GT and SWR2310-18GT fit in a 19-inch rack mount 1U size. When installing them in a 19-inch rack, attach the included rack mount hardware (2 pcs.) using the included screws (8 pcs.). Here we explain using the SWR2310-28GT as an example. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Use a Phillips screwdriver to firmly fasten the screws.
Installation on a wall or ceiling Installation on a wall or ceiling SWR2310-18GT / SWR2310-10G Use the separately sold WK-SWR wall mount accessory to install the unit. If attaching this unit to a ceiling, invert the top and bottom of the unit. You will need to obtain six screws that fit the holes described in step 1 and are appropriate for the material and thickness of the wall or ceiling. Carry out the installation completely, all the way to step 7.
English Installation on a wall or ceiling 1. Place the mounting accessory against the wall or ceiling, and mark the installation location. SWR2310-18GT/SWR2310-10G Attachment surface (not stamped) Mark the wall 20 2-R2.5 ø10 5 A Wall installation surface (stamped) B B C C WK-SWR 2- ø 5.5 A D D D D C C B B A A 2. Provisionally attach four commercially available screws to the locations that you marked in step 1.
Installation on a wall or ceiling 4. Using four screws included with the mounting accessory, attach it to the SWR2310-18G/SWR2310-10G. Fasten it securely. Warning • Use only the specified screws that A A were included. If the unit falls, injury or damage might occur. This could also cause electric shock or malfunctions. • Take care when letting your hand or B B C C finger contact the corners of the mounting accessory. D D Inattention might cause injury.
English Settings Settings Settings for this unit can be made in the following ways. • Make settings using the Web GUI • Make settings from the command line using the CONSOLE port • Make settings from the command line using Telnet • Make settings from the command line using SSH This document explains “Make settings using the Web GUI” (page 28) and “Making settings from the command line using the CONSOLE port” (page 29). You can log in to this unit either as a standard user or as an administrative user.
Settings Make settings using the Web GUI Here we explain the procedure for logging in to this unit using the Web GUI. You will use Yamaha LAN Monitor to log in to the Web GUI, so install Yamaha LAN Monitor before you continue. Before you log in, connect your computer to the same network. For details on supported web browsers, refer to the Yamaha website. https://www.yamahaproaudio.com/ ° Logging in to this unit using a web browser 1. Start Yamaha LAN Monitor. 2.
English Settings Making settings from the command line using the CONSOLE port Here we explain the cable, driver, software, and settings that are necessary in order to use the CONSOLE port. ° Preparing a console cable • Connect the computer to the CONSOLE port of this unit using a USB cable or an RJ-45/DB-9 console cable.
Settings ° Logging in from a computer connected to the CONSOLE port 1. Using a console cable, connect this unit to the computer. Connect the computer to the CONSOLE port of this unit using a USB cable or an RJ-45/ DB-9 console cable. Notice • The LAN ports and the RJ-45 CONSOLE port all use the same 8-pin connector. If you connect these wrongly, hardware damage or malfunction might occur. Take care when making connections. • If you use the mini-USB CONSOLE port, do not use a USB hub.
Before changing the initial password for the initial administrative user name: When the password is successfully authenticated, the system will wait for a new password to be entered. Skip to step 6 and change the password. SWR2310-10G Rev.2.04.11 (Fri Jul 15 09:38:27 2022) Copyright (c) 2022 Yamaha Corporation. All Rights Reserved. Please change the default password for admin.
Connections Connections ° Connecting to a network device or a computer 1 3 5 7 9 11 13 15 17 19 21 23 25 27 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Notice Do not connect this product to public Wi-Fi and/or Internet directly. Only connect this product to the Internet through a router with strong password-protections. Consult your router manufacturer for information on security best practices.
3. To the connector, connect a fiber optic cable that is suitable for each module. English Connections Connector Fiber optic cable ° Removing an SFP module Secure this unit so that it will not move, and while grasping the lever of the SFP module, pull it slowly toward yourself to remove the module from the SFP/SFP+ port. Supported SFP modules and SFP+ modules are collectively referred to here as SFP modules. 1. Detach the fiber optic cable. Connector Fiber optic cable 2.
Connections ° Installing a direct attach cable SWR2310-28GT / SWR2310-18GT A direct attach cable (DAC-SWRT-3M, DAC-SWRT-1M) can be installed in an SFP+ port of the SWR2310-28GT or SWR2310-18GT. 1. Remove the protective cap from the SFP+ module section of the direct attach cable, and remove the dust cover from the SFP+ port of this unit. 2. Grasp the SFP+ module section of the direct attach cable, insert it firmly into the SFP+ port of this unit, and engage the lock.
° Making stack connections SWR2310-28GT Attach a direct attach cable or an SFP+ module (SFP-SWRT-SR or SFP-SWRT-LR) to an SFP+ port of the SWR2310-28GT. If using an SFP+ module, you must additionally provide a fiber optic cable that is suitable for the SFP+ module. For details on installing or removing a direct attach cable, refer to “Installing a direct attach cable” SWR2310-28GT / SWR2310-18GT (page 34) and “Removing a direct attach cable” SWR2310-28GT / SWR2310-18GT (page 34).
Initialization Initialization This unit can be restored to its factory-set state in the following ways. • Using the Web GUI to restore the factory settings (page 36) • Using the cold start command to restore the factory settings (page 37) • Entering the [I] (uppercase I) key during startup to restore the factory settings (page 38) Notice When restoring the factory settings, note the following points. • All communication is halted immediately after execution.
English Initialization ° Using the cold start command to restore the factory settings You can return the unit to its factory settings by using a command line setting via the CONSOLE port, Telnet, or an SSH client. Notice This step cannot be executed if the initial administrative password is specified. Use the “enable password” command to change the administrative password in advance.
Initialization ° Entering the [I] (uppercase I) key during startup to restore the factory settings The unit can be restored to its factory settings by entering an uppercase “I” when the unit is starting up. This explanation uses the method of disconnecting and reconnecting the power cord. The procedure is also the same when using the reload command to restart this unit. Notice Here we assume that you are logged in as described in “Logging in from a computer connected to the CONSOLE port” (page 30). 1.
English Appendix Appendix Hardware specifications Item SWR2310-28GT Dimensions (W x D x H units: mm) not including protrusions and feet Weight (without included items) CONSOLE port 330 mm(W) x 200 mm(D) x 43.5 mm(H) 220 mm(W) x 250 mm(D) x 40.5 mm(H) 3.9 kg 2.1 kg 1.7 kg AC100 – 240V, 50/60 Hz 25.2 W 19.0 W 11.7 W Standard RS-232C, USB 2.0 Connector RJ-45, USB mini-B (5-pin) Data transmission speed 9600 bit/s Standard IEEE802.
Appendix Item microSD slot SWR2310-28GT microSD/microSDHC (microSDXC is not supported) File System FAT/FAT32 MAC address Storage environment conditions SWR2310-10G Standard Indicators Operating environment conditions SWR2310-18GT POWER, microSD, STACK ID, LAN port (LINK/ ACT, SPEED), SFP+ port (LINK/ ACT, SPEED) POWER, microSD, LAN port (LINK/ACT, SPEED), SFP+ port (LINK/ACT, SPEED) Indicated in product label on top panel of unit Ambient temperature 0–50 °C Ambient humidity 15–80% (non-co
English Appendix Dimensional diagram 300 2.3 SWR2310-28GT 3 5 7 9 11 13 15 17 19 21 23 25 27 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Units: mm 3.2 1 44 47.2 440 200 2.3 SWR2310-18GT 330 3 5 7 9 11 13 15 17 2 4 6 8 10 12 14 16 18 3.2 43.5 46.
Appendix 250 2.3 SWR2310-10G 220 3 5 7 9 2 4 6 8 10 40.5 43.5 1 3 Units: mm RJ-45/DB-9 console cable pin configuration Console (RS-232C) Signal RJ-45 RTS DTR TxD GND GND RxD DSR* CTS* 1 2 3 4 5 6 7 8 D-SUB 9 9 8 6 2 5 3 7 4 1 * DSR and CTS signals are not used by the SWR2310 series.
English Appendix The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the top of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No.
Appendix Software license agreement The product firmware revision number can be updated. Updating the firmware revision is considered an indication of agreement to the Yamaha network product software license agreement. Before updating the firmware revision, be sure to carefully read the Yamaha network product software license agreement. If you cannot agree to the terms in the Yamaha network product software license agreement, do not update the firmware revision.
English Index A S Administrative password ..................... 36, 37 SFP ports .................................................. 13 SFP+ module ............................................ 32 SFP+ ports ................................................ 13 Stack connections ..................................... 35 Stack ID indicator ...................................... 13 C Cold start command.................................. 37 Command line...........................................
SWR2310-28GT SWR2310-18GT SWR2310-10G 383
Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
Información para usuarios sobre la recogida y eliminación de los equipos antiguos Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos no deben mezclarse con los desperdicios domésticos normales. Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje correspondientes, de acuerdo con la legislación nacional.
Yamaha Worldwide Representative Offices English For details on the product(s), contact your nearest Yamaha representative or the authorized distributor, found by accessing the QR code below. Deutsch Wenden Sie sich für nähere Informationen zu Produkten an einen Yamaha-Vertreter oder autorisierten Händler in Ihrer Nähe. Diese finden Sie mithilfe des QR-Codes unten. Français Pour obtenir des informations sur le ou les produits, contactez votre représentant ou revendeur agréé Yamaha le plus proche.
Yamaha Pro Audio global website https://www.yamahaproaudio.com/ Yamaha Downloads https://download.yamaha.com/ 产品名称 : 二层交换机 产品标准编号: GB 4943.