English Deutsch Français L2 SWITCH Русский Italiano Português Español SWP2-10MMF SWP2-10SMF 取扱説明書 EN DE FR ES PT IT RU JA 日本語 Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manual do Proprietário Manuale di istruzioni Руководство пользователя
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PA_en_11 1/2 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. This product is designed for audio network. Do not use for any purposes other than the one intended. Those who are unfamiliar with handling or those who can not handle according to this manual such as children, should be supervised by responsible persons to ensure safety. WARNING • Do not touch the product or the electric plug during an electrical storm.
PA_en_11 2/2 • When installing the product: - Do not cover it with any cloth. - Do not install it on a carpet or rug. - Make sure the top surface faces up; do not install on its sides or upside down. - Do not use the product in a confined, poorly-ventilated location. Inadequate ventilation can result in overheating, possibly causing damage to the product(s), or even fire. • If the product is mounted in an EIA standard rack, carefully read the section “Rack mounting” on page 6.
Rack mounting This unit is rated for operation at ambient temperatures ranging from 0 to 40 degrees Celsius. When mounting the unit with other SWP2 unit(s) or other device(s) in an EIA standard equipment rack, internal temperatures can exceed the specified upper limit, resulting in impaired performance or failure.
Software license agreement The product firmware revision number can be updated. Updating the firmware revision is considered an indication of agreement to the Yamaha network product software license agreement. Before updating the firmware revision, be sure to carefully read the Yamaha network product software license agreement. If you cannot agree to the terms in the Yamaha network product software license agreement, do not update the firmware revision.
Contents Introduction 9 Features .................................................................9 Included items .......................................................9 Option item.............................................................9 Related software ....................................................9 Settings and password ..........................................9 Documentation 10 Terms 10 Controls and Functions 11 Front panel ........................................................
Introduction Included items Thank you for choosing the Yamaha SWP2-10MMF, or SWP2-10SMF L2 switch. To take full advantage of the superior functions and performance offered by the SWP2, and to enjoy years of trouble-free use, be sure to read this owner’s manual carefully before operation. This owner’s manual is intended to be read by audio networking personnel.
Documentation In addition to this manual, the following documentation for the SWP2 is available. • Yamaha Audio Network Monitor User’s Guide (PDF) This explains installation, settings, and usage of the “Yamaha Audio Network Monitor” Windows application. • Command References (PDF) This explains the commands used when making settings from the command line of a computer. • Technical Data (HTML) This explains details of the SWP2’s functions.
Controls and Functions Front panel The explanation here is based on the SWP2-10MMF. 1 2 1 LAN ports These are etherCON (RJ-45) ports for connecting Ethernet cables (CAT5e or better is recommended). A cable with an RJ-45 connector can also be connected. All ports support 1000BASE-T, 100BASE-TX, and 10BASE-T. 2 10GBASE-SR ports (SWP2-10MMF)/ 10GBASE-LR ports (SWP2-10SMF) This is an opticalCON DUO port for connecting an optical fiber cable. LC Duplex connectors can also be connected.
Caution when using this unit together with another manufacturer’s switch Dante supports both IGMP V2 and V3, but you must set all switches in the same network to operate using the same version. If the SWP2 starts up with DANTE settings, it operates using IGMP V3. In this case, if the network includes even one switch that is operating with IGMP V2, problems such as dropouts in the sound might occur.
Rear panel 9 ) ! 9 Grounding screw Since the included power cord has a three-pin plug, this unit will be appropriately grounded if the AC outlet is grounded. In some cases, you may be able to reduce hum noise and interference noise by connecting this screw to ground as well. @ ! [EXT DC INPUT] connector This is an XLR-4-32 type jack for supplying an external power supply (+24 V) as a backup for the SWP2’s internal power supply.
Status Indicator Display If the LED mode is [LINK/ACT] SWP2 Initialization Settings can be reinitialized to factory default settings by the following three methods. The status indicators show each port’s link status and connection status. Indicator Upper Lower CAUTION Do not switch off the SWP2 during initialization. Doing so could cause a product failure. Illumination Status Lit green Link is established. (LINK) Flashing green Data is being transferred. (ACT) Unlit Link is lost.
Using commands to restore factory settings Factory settings can be restored using the [CONSOLE] port or a Telnet or SSH client. The following describes how to restore factory settings via the [CONSOLE] port. Preparing the computer Terminal software is required for controlling the computer serial (COM) port. Before starting, configure the terminal software parameter settings as indicated below.
VLAN Use Cases Separating control signals from audio signals Redundant Dante connections This case logically separates control signals such as for Editor or StageMix from Dante’s audio signals, making the network more stable. This diagram shows a setup using VLAN preset B. If VLANs are not used, and control signals and audio signals flow across the same network, the two will compete for communication bandwidth.
Specifications General specifications Parameter SWP2-10MMF SWP2-10SMF Number of LAN ports (1000BASE-T/100BASE-TX/10BASE-T, etherCON connector) 10 Number of SFP+ ports (10GBASE-SR, opticalCON DUO connector) 2 0 Number of SFP+ ports (10GBASE-LR, opticalCON DUO connector) 0 2 Console port 1 (RJ-45) Automatic negotiation Available Auto MDI/MDI-X Available DIP switches CONFIG, VLAN PRESET Indicators (Front) POWER, LED MODE × 4 PORT × 10 × 2*1, SFP+ × 2 × 2 Operating temperature range 0 to 4
Interface specifications Terminal Format Level Connector 1-10 *1 IEEE802.3 10BASE-T/100BASE-TX/ 1000BASE-T etherCON CAT5e 11, 12 *2 IEEE802.3ae 10GBASE-SR 10GBASE-LR*3 opticalCON RS-232C RJ-45 *4 CONSOLE (RS-232C) – EXT DC INPUT – – XLR-4-32 type *5 *1 These terminals support AutoMDI/MDI-X *2 Conforming cable: SWP2-10MMF: GI-type multi-mode fiber cables with a core diameter /cladding diameter of approximately 50 μm/ 125 μm.
Dimensions 362 355 430 44 480 Unit: mm * The contents of this manual apply to the specifications as of the firmware Rev. 2.03.15. To obtain the latest manual, access the Yamaha website then download the manual file.
Important Notice: Guarantee Information for customers in European Economic Area (EEA) and Switzerland English Important Notice: Guarantee Information for customers in EEA* and Switzerland For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country.
Yamaha Pro Audio global website https://www.yamahaproaudio.com/ Yamaha Downloads https://download.yamaha.
