V2.
CONTENTS Contents Supporting a new HY144-D-SRC card .............................................................3 Supporting a new HY128-MD card .................................................................4 MIX SEND COPY .............................................................................................. 6 Additional option during loading.................................................................... 7 Displaying a patch conflict between DSP engines.....................................
CONTENTS Supporting a new HY144-D-SRC card If you plan to set the clock master to Internal or TWINLANe SLAVE on the device that has this card installed, use Dante Controller to check the “Enable Sync to External” option for this card, and operate the card as the master on the Dante network. • You cannot specify a card operating in Asynchronous SRC mode as the clock master. Specify a different device as the word clock master.
CONTENTS Supporting a new HY128-MD card The screen is displayed when the HY128-MD card is inserted into HY SLOT 3 on a DSP engine. The screen contains the following items: Supporting a new HY128-MD card 1 REDUNDANCY MODE Enables you to select one of two redundancy combinations. This audio interface card transmits and receives up to 128-in/128-out MADI signals. This card features two sets of fiber optic and coaxial connectors, supporting redundant connection.
CONTENTS Supporting a new HY128-MD card 3 SPLIT button Specifies whether or not the input signal should be split and sent to the output connectors. The signal will be sent to the same type of output connectors. ! SRC CLOCK buttons Enable you to select the output signal clock while the SRC is turned on. • MADI IN • ON The output signal will use the clock that is being input at the corresponding MADI IN connector. The input signal is split and sent to the output connectors.
CONTENTS MIX SEND COPY ■ About the SOFT CTRL (software control) switches on the HY128-MD card MIX SEND COPY If the switch 1 is set to ON (default setting), you can use the control surface to view and modify the parameter settings. If the switch 1 is OFF, the parameter settings will be fixed by the DIP switch settings on the card. For more information, please refer to the “HY128-MD Owner’s Manual.
CONTENTS Additional option during loading • If a STEREO channel is selected: To Stereo A To Stereo B Additional option during loading NOTE The WITH SENDS button will be grayed out and disabled under the following conditions: • The copy source or paste destination is a surround bus, downmix bus, or mix minus bus. • The copy source and paste destination use a different type of bus (VARI/FIX). Now you can select whether the Dante audio network settings are loaded while a project file is being loaded.
CONTENTS Displaying a patch conflict between DSP engines ■ Confirmation dialog when stealing a patch Displaying a patch conflict between DSP engines Assuming that a DSP engine is already patched to an output port on the TWINLANe network, if you try to patch another DSP engine to that same output port, a confirmation dialog will appear on the control surface that you are operating, asking whether you want the patch to be “stolen” by the second DSP engine.
CONTENTS Displaying a patch conflict between DSP engines ■ Message regarding a stolen patch ■ Patch screen OUTPUT patch screen 2 1 1 TWINLANe network (main/sub) assignment display The number of patches is shown in red for the output channels that are not assigned to the TWINLANe network. (The left half represents main, and the right half represents sub.
CONTENTS Expanded SENDS ON FADER mode function Expanded SENDS ON FADER mode function Additional CUE monitor sources CUE A, CUE B, and TALKBACK2 have been added as monitor sources that can be assigned to the MONITOR SOURCE DEFINE buttons. (TALKBACK2 is a talkback signal on the control surface that has its CONSOLE ID set to “2”.) In this way, you can mix and monitor CUE A, CUE B, TALKBACK 1, or TALKBACK 2 along with other monitor sources.
CONTENTS Mirroring Operation Check function PHONES popup window Mirroring Operation Check function The new Mirroring Operation Check function enables you to check whether DSP mirroring is operating properly. You can check the operation while two DSP engines are in a mirroring configuration. Since this function virtually pauses DSP engine operation, you can use the function at the time of system setup.
Yamaha Pro Audio global website https://www.yamaha.com/proaudio/ Yamaha Downloads https://download.yamaha.
