CONTROL SURFACE CS-R5 Owner’s Manual EN
ATTENTION RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the rear of the unit. ATTENTION : POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION, FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference.
PA_en_11 1/2 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe place for future reference. This product is suitable for use in a hall or event. Do not use for any purposes other than the one intended. Individuals who are not familiar with the proper way to handle this type of product, or individuals who cannot handle this type of product in accordance with the instructions in this manual, should be supervised by responsible persons to ensure safety.
PA_en_11 2/2 • Do not place the product in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction. • Before moving the product, remove all connected cables. • When transporting or moving the product, always use three or more people. Attempts to lift this product by only one or two individuals may result in injuries, such as back injuries, or cause the product to be dropped and broken, which could lead to other injuries.
Information About copyrights • Copying of commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. About functions/data bundled with the product • Even when the Power switches are in standby status (power lamp is off), electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure you unplug the power cord from the wall AC outlet.
Contents PRECAUTIONS...........................4 Troubleshooting ....................29 Introduction ............................8 Specifications ........................30 About manuals.................................. 8 General Specifications ..................... 30 About utility software ........................ 9 Audio Specifications ........................ 30 Firmware updates ............................. 9 Input/output Characteristics ............ 31 Conventions in this manual............
Introduction Thank you for purchasing the Yamaha Control Surface CS-R5. The CS-R5 is a control surface dedicated to the Yamaha RIVAGE PM5 series digital mixing system. This manual provides information regarding the basic functions and operations for mixing engineers and technical personnel at audio installation companies. In order to take full advantage of this system's superior functionality and enjoy years of trouble-free use, please read this manual before you use the product.
About utility software Conventions in this manual The RIVAGE PM series can be used with a variety of utility software. In this manual, switch-type controllers on the panel are called “keys.” Control knobs on the panel are called “knobs.” Some knobs rotate from a minimum value to a maximum value, while others rotate endlessly. Virtual buttons displayed on the screen are called “buttons,” and virtual knobs are called “knobs.” Controls located on the panel are enclosed in square brackets [ ] (e.g.
Part Names & Functions Top panel E A E C F A Selected Channel section ➔ page 11 B UTILITY section ➔ page 13 C SCENE MEMORY section ➔ page 14 D USER DEFINED KEYS section ➔ page 15 E Touch Screen section ➔ page 16 F Channel Strip section ➔ page 17 10 CS-R5 Owner’s Manual D F B
A Selected Channel section This section enables you to adjust parameters for the selected channel. The knobs in the Selected Channel section feature the Touch Sense function. DYNAMICS 1/2 This section enables you to select Dynamics 1 or 2, and make detailed settings. You can also view the input level and the gain reduction of selected Dynamics. 23 4 1 7 6 5 8 9 1 DYNAMICS [1]/[2] keys These enable selection of Dynamics 1 or 2. 2 DYNAMICS 1/2 IN LEDs Indicates the input level of selected Dynamics.
GAIN, HPF, PAN, Fn 1 [GAIN] knob Controls the analog gain or digital gain. 1 2 HPF [ON] key Switches the HPF on or off. 2 3 [HPF] knob Adjusts the HPF cutoff frequency. 3 4 [PAN] knob Adjusts the panning of the signal sent to the stereo buses. 5 [Fn] (Function) knob Adjusts the specified parameter. 4 5 EQUALIZER 1 EQUALIZER [ON] key Switches EQ on or off. 1 2 EQUALIZER [Q] knobs Specify the Q value. 2 3 4 12 CS-R5 Owner’s Manual 3 EQUALIZER [GAIN] knobs Adjust the gain.
B UTILITY section 1 2 3 2 USB port Enables you to connect a USB device (such as a mouse, keyboard, or USB flash drive). Use a USB flash drive to store the system’s internal data and to load the stored data into the system. ■ Supported USB flash drive format The FAT16 and FAT32 formats are supported. ■ Write Protection Some USB flash drives feature write protection that prevents data from being erased inadvertently.
C SCENE MEMORY section 1 [OVERLAY] key Press this button to display the OVERLAY SETTING screen. While pressing and holding down the [SHIFT] key (see 5 on page 17), press the [OVERLAY] key to switch Overlay on or off. While Overlay is turned on, press and hold down the [OVERLAY] key to enter Overlay edit mode. 4 1 2 3 5 6 8 2 [UNDO] key Cancels the most recent scene operation of storing, recalling or updating a scene.
D USER DEFINED KEYS section 1 USER DEFINED [A]/[B]/[C]/[D] BANK keys Select the bank ([A], [B], [C], or [D]) for the USER DEFINED knobs or USER DEFINED keys. 2 USER DEFINED keys [1]–[12] Control the functions as assigned by the user. 3 USER DEFINED KEYS displays Indicate the functions assigned to the USER DEFINED keys.
E Touch Screen section (Bay L, Bay C, Bay R) Bay L Bay C Bay A “bay” consists of a group of 12 faders located across the Touch Screen section and the Channel Strip section. The CS-R5 contains three bays. You can control these bays independently. Bay R 1 2 3 4 5 1 Touch screen This is a multi-touch screen that you can operate by touching it with your finger to select menus or set parameters. The touch screen will not respond correctly if you are wearing gloves.
F Channel Strip section (Bay L, Bay C, Bay R) 1 [ENCODER ASSIGN] key Displays a screen that enables you to switch between the Screen Encoder function and the Channel Encoder function. You can use only the Channel Encoder function for channel strips A and B. 2 [HOME] key Recalls a group of settings for the bay.
@ # 7 Strip encoder You can use the Screen Encoder function and the Channel Encoder function for channel strips 1–12. Use the [ENCODER ASSIGN] key (see 1 on page 17) to toggle between these two functions. You can use only the Channel Encoder function for channel strips A and B. • Screen Encoder function: Up to 12 parameters can be assigned by selecting controls on the screen. • Channel Encoder function: Parameters for 12 channels on the channel strips can be assigned.
^ INPUT [1]/[2] keys Enable you to select an input layer. Press the INPUT [1] key to select the INPUT 1-72 layer. Press the INPUT [2] key to select the INPUT 73-144 layer. ^ & NOTE * Press the INPUT [1] key and INPUT [2] key simultaneously to select the INPUT 145-288 layer. Press these two keys simultaneously again to select the INPUT 1-144 layer. When the INPUT 145-288 layer is selected, these key indicators light up in a different color than when the INPUT 1-144 layer is selected.
Front panel 1 1 PHONES A/B [LEVEL] knobs Adjust the level of the signal output from the PHONES output jacks respectively. 2 PHONES A/B output jacks These are headphone jacks for monitoring the MONITOR or CUE signal.
Rear panel 1 6 7 2 3 1 5 1 & 9 8 4 * ) ! ( % # @ $ 1 LAMP jacks These four 4-pin female XLR output jacks are used to supply power to optional Yamaha LA1L gooseneck lamps. 2 MIDI OUT/IN jacks These jacks are used to transmit/receive MIDI messages to/from external MIDI devices. 3 GPI connector This is a D-sub 25-pin female connector that allows communication (8-in, 8-out) with a GPI-equipped external device. 4 [FAN] switch Sets the internal cooling fan to operate at either HIGH or LOW speed.
9 USB ports Use these ports to connect a USB storage device such as a flash drive, USB mouse, or USB keyboard. % LINK/ACT indicator This indicator flashes or lights up green, depending on the connection status. ) MY card slots Install optional Mini-YGDAI I/O cards here to expand I/O ports. ^ NETWORK connector This RJ-45 connector allows the unit to be connected to a computer or network device via an Ethernet cable (CAT5e or higher recommended).
Power Supply / Shutdown Connecting to power sources 1. Turn off both power switches A and B on the unit. 2. Connect one of the supplied power cords to AC IN connector (A), and the other to AC IN connector (B). 3. Connect the other end of each power cord to an AC outlet of a different power source. Shutting down the power to the unit Before you turn off the power to the control surface, Yamaha recommends that you store the current status to scene memory.
Installing and Removing Optional Cards 3. Align both edges of the card with the guide rails inside the slot, and then insert the card into the slot. Push the card all the way into the slot so that the connector at the end of the card is correctly inserted into the connector inside the slot.
Touch Screen List windows Windows similar to the following enable you to select items from a list, such as a list of USER DEFINED keys. Basic touch screen operations This section explains the basic procedures you can perform on the unit’s touch screens. Pressing the touch screen You will use this operation primarily to switch screens and pages, to select the parameter to be operated, and to turn a button on/off. Some buttons enable you to change the value depending on the location you press.
Popup windows Viewing a touch screen When you press a button or field for a specific parameter in a screen, a window showing details or a list for that parameter will appear. These are called “popup windows.” The following examples describe two types of screens displayed on the touch screens. ■ OVERVIEW screen This screen shows the main parameters of 12 channels selected as a layer. You can switch between popup windows using tabs as needed.
Other Operations Initializing the unit to factory default settings If an error occurs in the unit’s internal memory, or if you forget the password and cannot operate the unit, you can use the following procedure to initialize the internal memory. NOTICE When you initialize the internal memory, all content that had been saved in memory will be lost.
If MOTOR DRIVE is selected: For the specified faders in the Channel Strip section and Master section, the motorized fader movement will be automatically calibrated. 5. Press the [SEL] key for each fader that you want to calibrate. Faders for which a problem was detected in the fader settings at start-up will already be selected. 6. Press the START button. The system starts optimizing the movement of the motorized faders. The corresponding [SEL] keys will flash during calibration.
Troubleshooting Please visit the Yamaha Pro Audio global website for a list of frequently asked questions (FAQ). http://www.yamahaproaudio.com/ Power does not turn on. ❍ Make sure that the power switches are turned ON. ❍ Make sure that the AC power cords are connected. ➥ If the power still does not turn on, contact your Yamaha dealer. The unit is not receiving an audio input signal. ❍ If you are using an optional card, make sure that it is installed properly.
Specifications General Specifications Mixing capacity 288 Inputs, 72 MIX + 36 MATRIX + 2 STEREO (DSP-RX-EX) Sampling frequency Internal clock Frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Accuracy ±50 ppm Jitter *1 1.0 ns @Fs=88.2 kHz/96 kHz, 2.0 ns @Fs=44.
Dynamic range Input Output OMNI IN 1–8 — RL Conditions Min. Typ. Max. Unit OMNI OUT 1–8 600Ω AD + DA, GAIN: –6 dB 115 dB OMNI OUT 1–8 600Ω DA Converter 120 dB * Dynamic range is measured with an IHF-A filter. Crosstalk (@1kHz) from/to to/from Conditions Min. Typ. Max.
I/O slot characteristics MY card slot × 2 Control I/O characteristics Terminal Format Level MIDI IN MIDI – DIN 5pin MIDI OUT MIDI – DIN 5pin USB 2.0 Host USB USB 1–4 *1 RECORDING NETWORK [PC] USB A (Female) USB 2.0 Host USB IEEE802.3 10BASE-T/100BASE-TX etherCON CAT5*2 *4 – 1000BASE-T etherCON CAT5e*3 *4 CONSOLE NETWORK IN/OUT USB A (Female) GPI*5 – – LAMP 1–3 – 0–12 V *1. *2. *3. *4. *5. *6.
Dimensional Diagrams 643 414 1444 Unit: mm Approximate Munsell value of exterior color: N5 * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.
Index A S ASSIGN......................................................................... 16 Screen encoder..............................................................18 SEL..................................................................................18 SEND / USER DEFINED KNOB...............................16 SENDS ON FADER .....................................................17 SHIFT ............................................................................17 Shutting down ......................
ADDRESS LIST NETHERLANDS/BELGIUM/ LUXEMBOURG NORTH AMERICA CANADA Yamaha Music Europe Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040 Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario, M1S 3R1, Canada Tel: +1-416-298-1311 FRANCE U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col.
Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads https://download.yamaha.