RX-V473_573_esg_C_cover1.
RX-V473_573_esg_C.fm Page 1 Monday, January 23, 2012 2:44 PM 1 Preparation AV Receiver Accessories Check that the following accessories are supplied with the product. Remote control Easy Setup Guide Insert the batteries the right way round. AM antenna English To reduce the impact on natural resources, the Owner’s Manual for this product is supplied on CD-ROM. For more information about this product, refer to the Owner’s Manual on the supplied CD-ROM.
RX-V473_573_esg_C.fm Page 2 Monday, January 23, 2012 2:44 PM 2 Placing speakers Set up the speakers in the room using the following diagram as a reference. For information on other speaker systems, refer to “Owner’s Manual”. 5.1-channel system 7.
RX-V473_573_esg_C.fm Page 3 Monday, January 23, 2012 2:44 PM 3 Connecting speakers/subwoofer • (U.S.A. and Canada models only) Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” in “Owner’s Manual”. 1 Connect the front speakers (1/2) to the FRONT (//\) terminals. 2 Connect the center speaker (3) to the CENTER terminal. The unit (rear) • (Except for U.S.A.
RX-V473_573_esg_C.fm Page 4 Monday, January 23, 2012 2:44 PM 3 Connect the surround speakers (4/ 5) to the SURROUND (//\) terminals. 4 Connect the subwoofer (9) to the SUBWOOFER jack. The unit (rear) Connect the surround back speakers (6/ 7) to the SURROUND BACK (//\) terminals. The unit (rear) The unit (rear) SPEAKERS SPEAKERS SPEAKERS PB PB PB FRONT For 7.
RX-V473_573_esg_C.fm Page 5 Monday, January 23, 2012 2:44 PM 4 Connecting external devices Before connecting the power cable (General model only) Make sure you set the switch position of VOLTAGE SELECTOR according to your local voltage. Voltages are AC 110-120/220-240 V, 50/60 Hz. TV Audio out (optical) HDMI in HDMI out HDMI HDMI BD/DVD player OPTICAL HDMI O HDMI b c HDMI OUT jack 1 a c Connect a TV to the unit with a digital optical cable.
RX-V473_573_esg_C.fm Page 6 Monday, January 23, 2012 2:44 PM 5 Optimizing the speaker settings automatically (YPAO) 1 The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. Connect the YPAO microphone to the YPAO MIC jack on the front panel. The following screen appears.
RX-V473_573_esg_C.fm Page 7 Monday, January 23, 2012 2:44 PM If “W-1:Out of Phase” appears • If any error message (such as E-1) or warning message (such as W-2) appears, see “Error messages” or “Warning messages” in “Owner’s Manual”. • If the warning message “W-1:Out of Phase” appears, see “If “W-1:Out of Phase” appears”. 3 Use the cursor keys (e/r) to select “SAVE” (Save) and press ENTER. Follow the procedure below to check the speaker connections.
RX-V473_573_esg_C.fm Page 8 Monday, January 23, 2012 2:44 PM 6 Playing back a BD/DVD Now let’s play back a BD/DVD. We recommend playing back multichannel audio (5.1-channel or more) to feel surround sound produced by the unit. Many more features! 1 Press HDMI 1 to select “HDMI 1” as the input source. VOL. HDMI1 CODE SET L SL SW C R SR SOURCE RECEIVER HDMI 1 2 3 4 2 3 4 5 6 AUDIO A V-AUX USB NET HDMI 1 AV 1 2 3 Start playback on the BD/DVD player.
RX-V473_573_esg_G.fm Page 1 Friday, February 3, 2012 4:52 PM 1 Préparation Ampli-tuner audio-vidéo Accessoires Vérifiez que les accessoires suivants sont fournis avec le produit. Télécommande Manuel de configuration rapide Français Ce document décrit l'installation d'un système à 5.1 ou 7.1 voies (RX-V573 uniquement) et explique comment restituer le son d'ambiance d'un disque BD/DVD sur l'unité. Afin de préserver l'environnement, le Mode d'emploi de ce produit est fourni sur CD-ROM.
RX-V473_573_esg_G.fm Page 2 Friday, February 3, 2012 4:52 PM 2 Installation des enceintes Installez les enceintes dans la pièce en vous reportant au diagramme suivant. Pour obtenir des informations sur les autres systèmes d’enceinte, consultez le « Mode d’emploi ». Système à 5.1 voies Système à 7.
RX-V473_573_esg_G.fm Page 3 Friday, February 3, 2012 4:52 PM 3 Raccordement des enceintes/du caisson de graves • (Modèles pour les États-Unis et le Canada uniquement) L'unité est configurée pour des enceintes 8 ohms par défaut. Lorsque vous raccordez des enceintes 6 ohms, réglez l'impédance d'enceinte de l'unité sur « 6 Ω MIN ». Pour plus d'informations, reportez-vous à la section « Réglage de l’impédance des enceintes » du « Mode d’emploi ».
RX-V473_573_esg_G.fm Page 4 Friday, February 3, 2012 4:52 PM 3 Raccordez les enceintes d'ambiance (4/5) aux bornes SURROUND (//\). 4 Raccordez le caisson de graves (9) à la prise SUBWOOFER. Pour le système à 7.1 voies (RX-V573 uniquement) Raccordez les enceintes surround arrière (6/7) aux bornes SURROUND BACK (//\).
RX-V473_573_esg_G.fm Page 5 Friday, February 3, 2012 4:52 PM 4 Raccordement des appareils externes Avant de raccorder le câble d’alimentation (modèle standard uniquement) Vérifiez que vous sélectionnez la position de permutation de VOLTAGE SELECTOR en fonction de la tension locale. Les tensions sont CA 110-120/220-240 V, 50/60 Hz.
RX-V473_573_esg_G.fm Page 6 Friday, February 3, 2012 4:52 PM 5 Optimisation automatique des réglages d’enceintes (YPAO) 1 Raccordez le microphone YPAO à la prise YPAO MIC sur le panneau avant. L’écran suivant apparaît. La fonction Yamaha Parametric room Acoustic Optimizer (YPAO) permet de détecter les raccordements des enceintes et de mesurer la distance entre ces dernières et la position d'écoute.
RX-V473_573_esg_G.fm Page 7 Friday, February 3, 2012 4:52 PM 3 Utilisez les touches du curseur (e/r) pour sélectionner « SAVE » (Save) et appuyez sur ENTER. Auto Setup Exit SAVE Suivez la procédure ci-dessous pour vérifier les raccordements de l’enceinte. Selon le type d’enceintes ou l’environnement, ce message peut apparaître, même si les enceintes sont correctement raccordées. Measurement Finished Start Si le message « W-1:Out of Phase » apparaît Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / +10.
RX-V473_573_esg_G.fm Page 8 Friday, February 3, 2012 4:52 PM 6 Lecture d’un disque BD/DVD Voyons maintenant comment lire un disque BD/DVD. Pour sentir les effets d'ambiance sonore produits par l'unité, nous vous recommandons de lire les disques avec le système audio multivoies (5.1 voies et plus). 1 Encore plus de fonctions ! Appuyez sur HDMI 1 pour sélectionner « HDMI 1 » comme source d'entrée. L'unité propose diverses autres fonctions. VOL.
RX-V473_573_esg_C_cover4.