User Manual

ManualsBrandsYamaha Manualsaudio & home theatreR-N803

Table Of Contents

R-N803 R-N803D Update Guide

AV17-0052

There are two ways to update the firmware on the R-N803 and R-N803D: connect to the Internet to update directly, or

use a USB storage device. Please see the Owner’s Manual for more information on updating via the Internet. This guide

explains how to update using a USB storage device.

See the R-N803 page on the Yamaha website for more information on issues that have been resolved in the firmware

update and new functions that have been added.

Preparing the firmware

1 Have a USB storage device ready for use.

The USB storage device must fulfill the following

conditions.

• Required conditions for USB storage

device

- Supports mass storage

- Formatted as FAT16 or FAT32

- Does not feature encryption

- Blank (no data stored on the device)

2 Download the latest firmware from the

Yamaha website.

See the R-N803 page on the Yamaha website.

3 Decompress the downloaded file.

The firmware you downloaded is a compressed file.

The decompressed file (R0445-****.bin) is the

firmware data file for update (the “****” will vary,

depending on the version).

4 Save the decompressed file (R0445-****.bin)

to the root folder (topmost folder) in the USB

storage device.

Now you’re ready to update.

Updating the firmware

NOTICE

Be absolutely sure not to turn off the power while the firmware is

updating. If the power is turned off during updating, the unit may

fail to start up again.

1 Press A (POWER) on the unit to switch off

the power.

2 Insert the USB storage device that you have

prepared into the USB jack.

3 Press A (POWER) while holding down

RETURN.

“ADVANCED SETUP” will appear in the display.

4 Turn the SELECT/ENTER knob until

“UPDATE · · · USB” is shown on the display.

Note

When “UPDATE · NETWORK” is shown on the display, press

SELECT/ENTER to display “UPDATE · · · USB”.

5 Press DISPLAY.

The firmware will start updating. Once the update

has completed, “UPDATE SUCCESS” will be shown

on the display.

6 Press A (POWER) to turn off the power.

7 Pull out the USB storage device.

This completes the firmware update. Wait for at least

5 seconds after the firmware update has finished,

before turning on the power. The next time you turn

on the power, the unit will operate with the updated

firmware.

R-N803 R-N803D Update Guide

VOLUME

PURE DIRECT

RETURN

CONNECT

PUSH - ENTER

TUNINGPRESET

BAND

MEMORY CLEAR

BASSINPUT

BALANCE

TREBLE

LOUDNESS

FLAT

-30dB

DIMMER MODE

DISPLAY

SELECT

PHONES

YPAO MIC

SPEAKERS USB

A (POWER)

SELECT/ENTER

RETURN

DISPLAY

USB jack

Summary of content (3 pages)

PAGE 1
EN AV17-0052 R-N803 R-N803D Update Guide There are two ways to update the firmware on the R-N803 and R-N803D: connect to the Internet to update directly, or use a USB storage device. Please see the Owner’s Manual for more information on updating via the Internet. This guide explains how to update using a USB storage device. See the R-N803 page on the Yamaha website for more information on issues that have been resolved in the firmware update and new functions that have been added.
PAGE 2
Checking the firmware version Follow the steps below to check the firmware version. 1 2 Press A (POWER) while holding down RETURN. “ADVANCED SETUP” will appear in the display, after which the firmware version will be displayed. Press A (POWER) to turn off the power. What to do if the update is unsuccessful Take the actions below and then try reapplying the update, if the update is unsuccessful. Cause Action The USB storage device may not be properly connected to the USB jack.
PAGE 3
If the firmware cannot be updated to the target version, or the power to this device might be cut off while updating, use the following method to update instead. NOTICE Be absolutely sure not to turn off the power while the firmware is updating. If the power is turned off during updating, the unit may fail to start up again.