OWNER'S MANUAL IMPORTANT! Please record the serial number of our unit in the space below: Mode! BB Serial No. The serial number Is located on the rear of the cabinet. Retain this Owner's Manual in g safe place for future reference. WARNING To pervert fire or shock hazard, do 1ot expose this apolitical 1o rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC HOCK, DO NOT REMOVE COVER (O BACK), NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL @ Explanation of Graphical Symbols The Lightning flash with arrowhead /y symbol, within an equilateral triangle, fi s intended to alert you to the presence ! of insulated “dangerous voltage” ¥ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
No. 70-1984, provides Information with aspect 1o proper grounding of the mast snd supporting structure, grounding of the lead-in wire to on antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
The 88 is # sophisticated stereo receiver, To ensure proper operating for the best possible performance, please read this manual carefully. 2 Chose the installation of your 8:8 carefully. Avoid placing it in direct sunlight er close to & sours of heat Also avoid dalmatians subject to vibration and excessive dust, beat, cold or moisture, Esp ways from such sources of hum as transformer or motors. 3 To ensure tho the unit operates properly, be sure level surface, and do not cover the heat vents on the op.
# CONNECTING THE SPEAKERS The matching impedance of this receiver is 60, Either one or o pairs of speakers may be connected. 1f ably e pair is connected the recommended speaker impedance may be anywhere between 49 and 16 I w0 pairs are connected, however, it is advisable to use speakers with at least a 89 impedance for optima performance, 1. Connect tae cords going 10 the left speakers to the L terminals and the right speaker cords to the R terminals, making sure that the and markings are observed.
# CONNECTING THE FM ANTENNA Choose an 1M antenna that is appropriate 10 the local reception conditions, Consider the distance from the broadest station and possible interfering objects such as surrounding tall buildings. n cases where there is a strung signal from & local station, a porthole T-type antenna is usually adequate. Connect the feeder wire to the 3008 terminal, stretch the wire out tight, and turn 1o obtain optimum reception.
CONNECTING VIDEO COMPONENTS VIDEO 2 {or VIDEO DISK) RCA VICED IN pin plug terminal TV Marion ® VIDEO SOURCE CONNECTION AND CONTROL The R-8 allows you to integrate previously separate audio and video systems into 3 true A7V home entertainment system, with high-fidelity progestin of video sources in stereo.
s Connecting Two Video Sources 1 you connect two video components, you will be able 1o copy tapes between them in ane direction, from VIDEO 2 to VIDEO 1. Far this reason, VIDEO 2 will always be your *'seduce program”, and VIDEO 1 your “copied program” when dubbing. The VICED OUT terminal for the VIDEO 2 source should thus be connected t0 your video monitor or TV set. Connections are made in the same way 25 for & single deck.
VOO COOS OVDPIDD® POWER SWITCH This is & “pussy-on, push-off* power switch.
® DIVED 1 By pressing this button, ihe video deck connected to VIDEO TERMINAL 1 can be seen and heard. The red LEL above it will fight & dives By pressing this button, video deck program ean be seen and heard. After pressing this button, select VIDEO 18 or VIDEO 2 @ The red LED above it wail fight. * For additional information, refer to CONNECTION and LISTENING TO A PROGRAM SOURCE. @ TUNER Depress this switch 1o listen 10 the tuner.
IR-83 % BASS CONTROL Lets you adjust bass response. The center, detonate, Fiat position is for normal response. @ MID CONTROL Lot you adjust Mid responds. The center, detentes, Fla position is for normal response @ TREBLE CONTROL Lets you adjust table response. The center, detentes, Flat position is For normal response, ® BALANCE CONTROL Used 10 adjust the relative volume fo the theft and right speakers.
@ REMOTE CONTROL (OPTION) When the main unit's power is ON, remote-control operation is possible by the SF-8 white the indicator is illuminate. &, This enables cremate control of parer ON/OFF, input signal switching, selection of preset stations, and increase/ decrease of the volume feel. 1f the main unit's power switch is eff ON and the power of the remote-control unit is theft OFF, the power will be switched ON when the power is resumed after 3 power failure.
s FM AM STATION CARD These cards can be used ta mark preset station. Tip out the holder {under the preset buttons} and change the cards as desired. @ SIGNAL QUALITY INDICATOR This indicator shows the strength of the received station. Wren tuning in & station, adjust the antenna's height and direction for maximum signal indication Multi path is an effect similar (o television ghosting; T it distorts the received signal and ISO causes put stereo separation and noise.
€@ FM AND AM SELECTOR Push to select TUNING MODE SELECTOR In the Auto mode, the tuner will automatically Sean the frequency bind when the Up or Dawn side of the tuning Hutton is pushed, and the Auto LED indicator @ will light up. I the Manual mode, the tuner will advance ont step at a time when the tuning button is pushed one, snd cont usually when it is pushed continuation. In addition, when st 1o the Auto position, any stereo FM broadcast will be received in stereo.
W LISTENING TO FM BROADCASTS 1, Set the input selector to Tuner, 2, Press the Function key to select FM. 3. Sat the Tuning Muse key 1o ~Auto”. 4. Press dither the Up ar the Down side of the Tuning key for 2 or 3 seconds. The recessive will automatically Sean the F-M band in the selected direction. When a station is found, e scan will stop and the station will bs docked in automatically. Use the Tuning key repeatedly 10 tune in your desired station. Statics may salsa be selected with the preset tuning keys.