PM1D Manager for Windows Operating manual E
PM1D Manager for Windows Operating manual Contents About the “PM1D Manager for Windows operating manual” . . . . . . . . . . . . . . . . . . . . . . 3 Conventions in the “PM1D Manager for Windows operating manual” . . . . . . . . . . . . . . . 3 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing PM1D Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the “PM1D Manager for Windows operating manual” About the “PM1D Manager for Windows operating manual” PM1D Manager for Windows (subsequently referred to as “PM1D Manager”) is an application program that runs on a computer running Microsoft Windows (subsequently referred to as the “PC”), providing the same operating environment as the software of the CS1D (subsequently referred to as the “console”).
PM1D Manager for Windows Operating manual Installing PM1D Manager This section explains how to install the PM1D Manager program. Before you install the software, you must read the license agreement (licence_e.txt) found on the “PM1D SYSTEM SOFTWARE” CD-ROM. You may use the software on the CD-ROM only if you accept the terms of this license agreement. If an older version of PM1D Manager is already installed, you must first uninstall it. (For the uninstallation procedure, refer to p.5.
Uninstalling PM1D Manager Continue following the on-screen instructions, and installation will be completed. When installation is complete, a shortcut icon will be added to the Start menu and to the desktop. Uninstalling PM1D Manager There are two ways to uninstall PM1D Manager. ■ Using “Add or remove an application” ■ Using Setup.exe 1. From the Windows “Start” menu, select “Start”“Settings”-“Control Panel.” 1. Perform steps 1–3 of “Installing PM1D Manager.
PM1D Manager for Windows Operating manual Using the application This section explains how to start and exit PM1D Manager, and how to perform basic operations. Starting You can use either of the following methods to start up PM1D Manager. 1 From the Windows “Start” menu, select “Start”“Programs”-“YAMAHA PM1D System”-“PM1D Manager” 2 Double-click the PM1D Manager icon that was created during the installation.
Using the application Initialization procedure If you want to initialize all current settings of the PM1D Manager and its scene memories and libraries, you can use the following procedure to restore the factory-set condition. 1. In the Function menu screen, click the OPTION button. The Option settings popup window will appear. 3. To execute the initialization, click the OK button. Memories that have been initialized cannot be recovered. Please use great care when performing this operation.
PM1D Manager for Windows Operating manual Screens unique to PM1D Manager This section explains the screens that differ from the console and are unique to PM1D Manager. Upper part of the display (common to all screens) 1 2 1 Connection status This area of the PM1D Manager screen will indicate the status of the connection between the PC and console or engine. • ........... Indicates that a cable is connected between the console/ engine and the PC, but communication has not been established. • ........
Screens unique to PM1D Manager Lower part of the function menu 2 Memory Setup Here you can reset the current PM1D Manager settings and memories/libraries to the condition in which they were immediately following installation. Each button has the following function. 1 2 3 4 1 EXIT button This button exits the PM1D Manager application. This button has the same result as selecting “Exit” from the “File” menu in the menu bar, or clicking the “Close” button in the upper right of the PM1D Manager window.
PM1D Manager for Windows Operating manual Communication between PM1D Manager and the console/engine If you connect the console/engine and the PC, you can use PM1D Manager as a supplementary controller for the system. • “Online” refers to a state in which the console/ engine and the PC are connected by a cable, and data can be transferred to control the device immediately.
Communication between PM1D Manager and the console/engine ■ System example 6: Dual Console mode PC1 Console1 (CS1D) PC2 Console2 (CS1D) Engine (DSP1D) • You can connect and use either PC1 or PC2 (not both). • Even if a PC is connected to console 2, it cannot be used.
PM1D Manager for Windows Operating manual Connections Connect the console/engine to your PC as shown in the following diagram. You can make connections in one of two ways: serial connection or USB connection. CS1D/DSP1D rear panel PC 1. Serial connection RS-232-C Serial cable PC serial port D-sub 9-pin (male⇔male) cross cable 2. USB connection USB USB cable USB port • When using USB connections, you must exit PM1D Manager before you power-on/off the console/engine or connect/disconnect cables.
Communication between PM1D Manager and the console/engine 6. In the Function menu screen, click the ONLINE/ OFFLINE button. The following popup window will appear. If you want to send data created within PM1D Manager to the console, save the PM1D Manager data on the PC to an ATA compatible PC flash storage card or CF (Compact Flash) card, and then insert this card into the PC ATA STORAGE CARD slot of the console and load the data.
PM1D Manager for Windows Operating manual Offline operating procedure To break communication between the online the console/engine and the PC, click the OFFLINE/ONLINE button in the lower part of Function menu screen. The following popup window will appear, so click the OK button and you will switch to offline mode. Immediately before PM1D Manager transitions from offline to online, all data is automatically backed up. (This is referred to as the recovery point.
Special considerations Special considerations This section notes various things you should be aware of concerning the parameters and operations in each screen. ■ PREFERENCE switch CONFIRMATION ON/OFF WARNING MESSAGES ON/OFF These settings are not linked with the console in the system, and therefore must be set individually. GATE/COMP GR METER ON/OFF LINK INTERNAL CALENDAR/CLOCK Since this indicates the date of the PC, it is not linked with the console.
PM1D Manager for Windows Operating manual ■ KEY IN CUE button (GATE PRM screen) Operation will change as follows, depending on the online/offline state of PM1D Manager and on the presence or absence of a console. Operable Offline Online Console exists in the system Not displayed. (*) Console does not exist in the system Operable (*) In order to avoid inconsistencies due to the fact that the selected channel is not linked between the PC and console, this will never be displayed on the PC.
USB MIDI Driver USB MIDI Driver If you are connecting the console/engine to a USB port on your PC, you’ll need to install the Yamaha USB driver. If this driver is already installed, or if you will be using a serial connection (RS-232-C connector), you do not need to install the USB driver. The procedure for installing the Yamaha USB driver depends on the version of Windows that you are using.
PM1D Manager for Windows Operating manual Windows Me 1. Start your PC and Windows, and insert the included CD-ROM into your PC’s CD-ROM drive. 2. Power-off the console/engine, and use a USB cable to connect the console/engine to the PC. The USB connector of the console/engine is located in the PC CONTROL section of the rear panel. 3. Turn on the console/engine. The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and reconnecting the USB cable.
USB MIDI Driver Windows XP 1. Power-on the PC, and when Windows starts up, log in using an account with Administrator privileges. 2. Insert the included CD-ROM into your PC’s CDROM drive. 3. Click the Start button, and then click Control Panel. If the Control Panel window appears as shown below, click “Switch to Classic View” on the left side of the window in order to see all the control panels. 4.
IP 20 Printed in Japan M.D.G.
