NUAGE Workgroup Manager Operation Manual EN
Contents Information ...........................................................................................3 NUAGE Workgroup Manager — An Introduction..............................3 Launching & Shutting Down ...............................................................3 Launching........................................................................................................... 3 Shutting down.....................................................................................................
Information Information • The NUAGE Workgroup Manager application and this manual are copyright of Yamaha Corporation. • Copying of the NUAGE Workgroup Manager application or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of Yamaha Corporation.
Using the Application Using the Application 5. Click to add the device or DAW application to the Workgroup area in the upper half of the window. Adding devices or DAW applications to the Workgroup Devices and DAW applications can be added to the Workgroup using the Main window (page 7). To do so, follow the procedure described below. (The Main window is displayed when NUAGE Workgroup Manager is opened.) 1. Connect the devices and the computers running the DAW applications using Ethernet cables. 2.
Using the Application Configuring devices and DAW applications Making connections Connect the various system components according to the following example. To configure any device or DAW application displayed in NUAGE Workgroup Manager, click the corresponding Property button. When you do so, a setting window for the device or DAW application will be displayed. The settings that can be made on this window will depend on the device or DAW application.
Using the Application Configuring the system 1. Open NUAGE Workgroup Manager. 2. Add the two DAW applications, the Nuage Fader, and the Nuage Master to the Workgroup. 3. Click Setup to open the Setup window (page 9). 4. Set the data to be transmitted from the RS232C ports on the Nuage Fader and the Nuage Master to the KVM switches when the buttons from the DAW Select section are pressed, and also set the corresponding transmission parameters.
Descriptions of Windows Descriptions of Windows Component names and functions NUAGE Workgroup Manager comprises the following four windows. 1 2 34 5 9 ) • Main window (page 7) • Property window (page 8) • Setup window (page 9) • About window (page 9) The Main window is displayed when you open NUAGE Workgroup Manager. The Property window (page 8), the Setup window (page 7), and the About window (page 7) can be opened by clicking Property, Setup, and About, respectively, on the Main window.
Descriptions of Windows 8 Name Property window These fields display the name of the corresponding device or DAW application. The name itself can be changed by clicking Property. It should be noted that the names of the devices and DAW applications in the Device/DAW List area cannot be changed. If you select a device or DAW application in the Workgroup area and click the Name field, you can change its assignment. 9 Identify These buttons can be used to identify the corresponding device or DAW application.
Descriptions of Windows Setup window 1 Network Interface This drop-down list is used to select the network adaptor on your computer that will be used with NUAGE Workgroup Manager. 2 Auto Register Select this check box to turn the Automatic Registration function on and clear to turn it off. If devices or DAW applications not currently in the Workgroup are identified on the network while this function is on, you will be asked whether or not you wish to add them to the Workgroup.
Troubleshooting Troubleshooting A device or DAW application is not displayed in the Device/DAW List area. • Devices: Ensure that the device is turned on. • DAW applications: Ensure that the application is running. • Devices: Try turning the device off once and then back on. • DAW applications: Ensure that your firewall settings have been suitably configured.
Messages Messages Message Meaning Add to Workgroup Add the device or DAW application to the Workgroup. Remove from Workgroup Remove the device or DAW application from the Workgroup. Please add DAW. Please add a DAW application to the Workgroup. Please add Device. Please add a device to the Workgroup. Please add Device and DAW. Please add a device or DAW application to the Workgroup. Please add DAW A. Please assign a DAW application to DAW A. Invalid file. The file could not be opened.
Added functions in NUAGE V2.0 Added support for remote operation of the MMP1 (Nuage Fader, Nuage Master, and NUAGE Workgroup Manager) Certain MMP1 functions can be controlled from the Nuage series. Settings (Preparations) Set the control source to Nuage Fader and/or Nuage Master and the control target to MMP1 with the NUAGE Workgroup Manager. 1. Open NUAGE Workgroup Manager. 2. Click “Setup.” 3. Set the IP address.
5. Confirm the connection between the MMP1 and Nuage device. When the MMP1 and Nuage device is connected correctly, the MMP1 indicator will light up in green. When the MMP1 indicator lights up in red (this means connection failure), the possible causes are as follows: • The IP address is incorrect. • The Passcode is incorrect. Please check the IP address settings and the Passcode.
Added functions in NUAGE V1.6 Added Support for Switching between Multiple Avid Pro Tools (NUAGE Workgroup Manager) You can now register two Avid Pro Tools in a Workgroup. (Previously, it was possible to register only one.) NOTE For more information about Avid Pro Tools settings, refer to the operation manual for Nuage Master or Nuage Fader.
Added Support for RMio64-D (NUAGE Workgroup Manager) 5 Output Clock Source You can now control the RMio64-D Dante/MADI conversion audio interface remotely from NUAGE Workgroup Manager. Same as Input Clock Source Syncs the MADI output signal with the MADI input signal. Same as Word Clock Source Syncs the MADI output signal with the RMio64-D clock. Enables you to select the MADI output signal when SRC is on as the word clock source.
Yamaha Pro Audio global website https://www.yamaha.com/proaudio/ Yamaha Downloads http://download.yamaha.