Español Français Deutsch English TOOLS for n Version2/Cubase AI 4 EN DE FR ES
SPECIAL NOTICES English Yamaha makes no representations or warranties with regard to any problems while attempting to copy the disks or software and cannot be held responsible for the results of attempts to copy the data. • The software included in the TOOLS for n Version2 CD-ROM and this Installation Guide are the exclusive copyrights of Yamaha Corporation. • The software included in the Cubase AI 4 DVD-ROM and the copyrights thereof are under exclusive ownership by Steinberg Media Technologies GmbH.
About the Disks Included in the Package Table of Contents About the Disks Included in the Package ................. 3 Changing settings after installation......................... 14 Operating System (OS) ............................................ 3 CD/DVD-ROM Installation Procedure....................... 3 Disk Contents ........................................................... 4 System Requirements for Software ..........................
About the Disks Included in the Package Disk Contents The disks contain the following software and data. ● TOOLS for n Version2 Software Name Contents TOOLS for n Version2 TOOLS for n Version2 consists of two software components: Yamaha Steinberg FW Driver and n Extension. Yamaha Steinberg FW Driver enables audio/MIDI signals to be transferred between a computer and the n8/n12 via IEEE1394 cables. Up to three devices compatible with Yamaha Steinberg FW Driver can be used simultaneously.
About the Disks Included in the Package Frequency/resolution: 44.1 kHz/24 bit Audio playback tracks: 16 Audio recording tracks: 1 MIDI playback tracks: 18 MIDI Remote Control/Automation Send effects (plug-in): 3 Insert effects (plug-in): 9 Plug-in synthesizer: 2 Latency: about 6 msec Minimum system requirements Frequency/resolution: 44.
About the Cubase AI 4 DVD-ROM About the Cubase AI 4 DVD-ROM Installation NOTE · If you have already installed a version of Cubase compatible with the Link function, such as Cubase 4.5, the instructions for “Installing Cubase AI 4” are not necessary. Jump to the next section “Installing TOOLS for n Version2.” 3 IMPORTANT English • Before breaking the seal of the Cubase AI 4 DVD-ROM package, please read carefully the Steinberg Software End User License Agreement (EULA) on page 20 of this manual.
About the TOOLS for n Version2 CD-ROM Installation(Windows XP) 1 2 3 4 6 Make sure that the power to the n8/n12 is turned off. Using an IEEE1394 cable, connect the n8/n12 directly to the computer (without using a hub), and disconnect all other IEEE1394 devices from the computer. Start the computer and log on to the Administrator account. Select [Start] (➝ [Settings]) ➝ [Control Panel]. If the control panel appears as shown below, click “Switch to Classic View” in the upper left of the window.
About the TOOLS for n Version2 CD-ROM 12 Follow the on-screen instructions in the Setup window for Yamaha Steinberg FW Driver, n Extension appearing in order. NOTE · If the same version of each software component has already been installed in your computer, the installation window of the corresponding software will not appear. · If a message “The software you are installing has not passed Windows Logo Testing” appears, click [Continue Anyway]. You do not need to abort the installation.
About the TOOLS for n Version2 CD-ROM Confirming the installation 1 2 Double-click on the System icon to call up the System Properties window. Select the Hardware tab and click [Device Manager]. Click on the [+] mark next to “Sound, video and game controllers,” and confirm that “Yamaha n series FW,” “Yamaha Steinberg FW Bus,” “Yamaha Steinberg FW WDM Audio” and “Yamaha Steinberg FW WDM MIDI” are listed. English 3 4 Select [Control Panel] from the Start menu.
About the TOOLS for n Version2 CD-ROM Installation(Windows Vista) Preparing to install Software Installation 1 2 The installer will install the following two software components to your computer. · Yamaha Steinberg FW Driver · n Extension 3 English 4 5 Make sure that the power to the n8/n12 is turned off. Using an IEEE1394 cable, connect the n8/n12 directly to the computer (without using a hub), and disconnect all other IEEE1394 devices from the computer.
About the TOOLS for n Version2 CD-ROM 13 When installation is complete, a message indicating so appears. If restarting of the computer is necessary following successful completion of the installation, make sure that the radio button to the left of “Yes, I want to restart my computer now” is selected, then click [Finish] to restart the computer. If restarting the computer is unnecessary, click [Finish] to exit the installation process.
About the TOOLS for n Version2 CD-ROM Installation(Macintosh) Preparing to install 1 2 English 3 4 5 Make sure that the power to the n8/n12 is turned off. Using an IEEE1394 (Firewire) cable, connect the n8/ n12 directly to the computer (without using a hub), and disconnect all other IEEE1394 devices from the computer. 10 NOTE · If an older version of the Yamaha Steinberg FW Driver has already been installed in your computer, [Update] may appear instead of [Install].
About the TOOLS for n Version2 CD-ROM /User/{Account name}/Library/Preference/ com.yamaha.YamahaFWCM.plist * “{Account name}” indicates the account name when Yamaha Steinberg FW Driver is installed. Removing n Extension Remove the following folders and files from the boot disk (usually Macintosh HD). English / Library/Application Support/Steinberg/Components/ yamaha_n.bundle yamaha_n_u.
Changing settings after installation Changing settings after installation This Control Panel window lets you set basic n8/n12 parameters when using Yamaha Steinberg FW Driver. The Control Panel consists of the General window, n8/n12 window and About window which lets you set the parameters such as sampling rate and WORD CLOCK Source. The settings here are immediately applied to the n8/n12.
Changing settings after installation 4 ASIO Buffer Size (Windows only) About window Determines the buffer size for the ASIO driver. 5 Input Latency/Output Latency (Windows only) Indicates the delay time for the audio input/output in millisecond units. Audio latency differs depending on the value of the ASIO Buffer Size. The lower the value of the ASIO Buffer Size, the lower the value of Audio Latency. 6 Audio Routing (Windows only) Click this to call up the WDM Audio Routing window.
Using multiple devices compatible with Yamaha Steinberg FW Driver Using multiple devices compatible with Yamaha Steinberg FW Driver Up to three devices compatible with Yamaha Steinberg FW Driver can be used simultaneously. By connecting them in daisy-chain fashion to a computer via IEEE1394 cables, you can upgrade your music production system simply by adding other devices.
Hints for using audio data (Windows) Hints for using audio data (Windows) For optimum use of the audio functions, we recommend you make the following settings. These settings minimize possible audio problems, such as drop outs, glitches and noise.
Troubleshooting Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
License Agreement for TOOLS for n Version2 License Agreement for TOOLS for n Version2 ATTENTION SOFTWARE LICENSE AGREEMENT PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION (“YAMAHA”). 1.
License Agreement for Cubase AI 4 License Agreement for Cubase AI 4 Steinberg Software End User License Agreement (EULA) General English All intellectual property rights in the software belong to Steinberg Media Technologies GmbH (hereinafter: “Steinberg”) and its suppliers. Steinberg permits you only to copy, download, install and use the software in accordance with the terms and conditions of this Agreement.
License Agreement for Cubase AI 4 5.4. The reinstallation of the software - on the same or another computer - is permitted only in case the already installed software cannot be used any more (e.g. following deinstallation). If the software does not use a Steinberg key, but requires activation codes, the new activation codes may be obtained from the user’s online account for support created during the personal product registration.
License Agreement for Cubase AI 4 11.3. Limited Warranty outside the EU: In the event that you as a fi rst buyer of the software are located outside the EU, the following limitation of liability shall apply. 11.3.1.
License Agreement for Cubase AI 4 English MEMO TOOLS for n Version2/Cubase AI 4 Installation Guide 23
U.R.G.