MTX-MRX Editor User Guide MTX-MRX Editor is software for connecting, constructing, and controlling a system that uses MTX series, MRX series, XMV series, EXi8/EXo8, R series (AD/DA), and Tio1608-D units. The settings you make in MTX-MRX Editor are sent to the MTX series, MRX series, XMV series, EXi8/EXo8, R series (AD/DA), and Tio1608-D units that are connected via Ethernet. After the settings have been sent, the system will operate without a computer.
Contents Notice regarding data copyright .................1 Chapter 3. Project screen................................34 Notice regarding the content of this user guide............................................1 ❏ System selection tabs ...........................................34 Chapter 1. An overview of MTX-MRX Editor ....4 Network devices .........................................35 ❏ HIDE/SHOW button...........................................34 MTX/MRX system.....................................
Contents “EXT. I/O” screen .................................... 120 ❏ “Match Device by IP Address” dialog box ........174 ❏ “YDIF” screen (Distribution mode)................. 120 ❏ “MTX Configuration” dialog box .....................177 ❏ “YDIF In Patch” dialog box .............................. 123 ❏ “Dante Information” dialog box.......................180 ❏ “YDIF Out Patch” dialog box ........................... 123 ❏ “Word Clock” dialog box ..................................
Chapter 1. An overview of MTX-MRX Editor An audio system control network When multiple MTX series, MRX series, XMV series, EXi8/EXo8, R series (AD/DA), and Tio1608-D units are connected to an Ethernet network, they will operate together as a single audio system. This is called an “MTX/MRX system,” and a space containing multiple MTX/MRX systems is called a “project.” If a computer is connected to the network, the computer can control the MTX/MRX system via the MTX/MRX.
Chapter 1. An overview of MTX-MRX Editor Terms used in this user guide These settings are not included in a preset file. ● Preset A preset is a set of parameters. Presets can be recalled from a DCP unit, a wireless DCP, or an MCP1 unit, via GPI, from an MTX unit or MRX unit, or from MTX-MRX Editor. Fifty presets can be stored in an MTX/MRX system.
Chapter 1. An overview of MTX-MRX Editor Data handled by MTX-MRX Editor Data handled by MTX-MRX Editor Project file (.
Chapter 1. An overview of MTX-MRX Editor Connection requirements for an MTX/MRX system Connection requirements for an MTX/MRX system The requirements for an MTX/MRX system are as follows. A maximum of 80 devices such as MTX/MRX/EXi/EXo/XMV/R series (AD/DA)/Tio1608-D/ MCP1/PGM1 units can belong to one project.
Chapter 1. An overview of MTX-MRX Editor Connection requirements for an MTX/MRX system The following diagram shows these requirements applied in MTX-MRX Editor’s Project screen.
Chapter 1.
What are YDIF connections? (Cascade mode and Distribution mode) Chapter 1. An overview of MTX-MRX Editor What are YDIF connections? (Cascade mode and Distribution mode) An MTX/MRX system has the following two connection modes. When connecting multiple YDIF devices (when making YDIF connections), you must choose one of these modes. In either case, the system can easily be expanded at low cost. Use the “Device Configuration Wizard” dialog box to switch modes.
Chapter 1. An overview of MTX-MRX Editor What are YDIF connections? (Cascade mode and Distribution mode) If only MTX units are connected Connection RING connection 01 MTX3 02 MTX3 03 MTX3 04 MTX3 Up to four MTX units can be connected. Connections can be in any order. Use the [Device Configuration Wizard] to switch both settings. YDIF MODE = CASCADE YDIF MODE = DISTRIBUTION To switch the settings of the two modes, click the [System] menu command “MTX Configuration” and make settings for each matrix.
Chapter 1. An overview of MTX-MRX Editor What are YDIF connections? (Cascade mode and Distribution mode) If MTX/MRX units and other YDIF units are connected Connection RING connection 01 EXi8 02 MTX5-D 03 MTX3 04 XMV4280 05 EXo8 Up to eight units can be connected via YDIF. Connections can be in any order. Cascade mode If a device other than an MTX is connected, it is not possible to select Cascade mode. Distribution mode YDIF patching is done in the “EXT. I/O” screen.
What are Dante connections? (Daisy-chain connection and Star connection) Chapter 1. An overview of MTX- What are Dante connections? (Daisy-chain connection and Star connection) A Dante network can be connected in two ways. Set the DIP switches of the devices as appropriate for the type of connection. ❑ Daisy-chain connection In a daisy-chain connection, each device is connected to the next device, in a chain. This method makes it simple to construct a network, and does not require a network switch.
What are Dante connections? (Daisy-chain connection and Star connection) Chapter 1. An overview of MTX- ❑ About redundant networks A redundant network is a network consisting of two circuits: a primary circuit and a secondary circuit. Normally, communication occurs on the primary circuit, but if a problem such as a broken cable occurs on the primary circuit, communication will automatically switch to the secondary circuit.
Chapter 1. Patching An overview of MTX-MRX Editor Patching In a digital audio network such as YDIF or Dante that comprises the MTX/MRX system, you will make settings on the transmitting device to specify “which output channel/bus’s signals will be sent to which channels of the digital audio network,” and make settings on the receiving device to specify “which channels of the digital audio network will be received on which input channels.
Chapter 1.
Chapter 1.
Chapter 1. Workflow An overview of MTX-MRX Editor Workflow Start MTX-MRX Editor. The “Startup” dialog box will appear. When you select [New file], the “Device Configuration Wizard” dialog box will appear. NOTE When you install MTX-MRX Editor, a project file linked with the “MTX Setup Manual” and “MRX Setup Manual” is installed in the following folder. ● For a 32-bit OS C:/Program Files/Yamaha/MTX-MRX Editor/V*.*/ProjectFile ● For a 64-bit OS C:/Program Files(x86)/Yamaha/MTX-MRX Editor/V*.
Chapter 1. Workflow An overview of MTX-MRX Editor For details, refer to Project screen. Change the functions of the MTX. To change the functions of input ports and stereo input channels, use the “MTX Configuration” dialog box, which can be opened from the [System] menu. Specify the patching between the MTX/MRX and the peripheral devices. You’ll make these settings in the “EXT. I/O” screen. To access the “EXT. I/O” screen, click the [EXT. I/O] button in the System screen.
Chapter 1. Workflow An overview of MTX-MRX Editor Specify the MTX’s input channel settings. Use the “Input Patch” dialog box to assign ports to input channels. To open the “Input Patch” dialog box, click a port select button in the MAIN screen. “Input Patch” dialog box Port select buttons For details, refer to “Input Patch” dialog box. In the same way, use the “Output Patch” dialog box to assign ports to output channels. Edit the component parameters.
Chapter 1. Workflow An overview of MTX-MRX Editor Make DCP, Wireless DCP, MCP1, PGM1/PGX1, GPI, and Scheduler settings. You’ll make these settings in the following dialog boxes. DCP settings: “Digital Control Panel” dialog box (On the [Controller] menu, click [Digital Control Panel].) Wireless DCP settings: “Wireless DCP” dialog box (On the [Controller] menu, click [Wireless DCP].) MCP1 settings: “MCP1” dialog box (On the [Controller] menu, click [MCP1].
Chapter 1. Workflow An overview of MTX-MRX Editor Use the rear panel [UNIT ID] rotary switch and DIP switches to set the UNIT ID of each device. In MTX-MRX Editor, the UNIT ID is shown as a hexadecimal number. Use the DIP switches (switches 1–2 on the MTX/MRX and EXi8/EXo8, switches 1–3 on PGM1 and YDIF-equipped models of XMV) to specify the upper digit, and use the [UNIT ID] rotary switch to specify the lower digit.
Chapter 1. Workflow An overview of MTX-MRX Editor Connect the devices and your computer as shown in the configuration diagram. Connect the device to the computer using its [Dante] connector for a Dante-equipped unit or its NETWORK connector for an MCP1 and YDIF-equipped unit. Normally you will connect the devices to the computer via a network switch. Only in the case of Danteequipped models when using a daisy-chain connection, you will connect the units to the computer in a daisy-chain.
Chapter 1. Workflow An overview of MTX-MRX Editor Verify that the firmware versions of the devices are compatible with MTX-MRX Editor. For details, refer to the “Device Information” dialog box which you can access from the [System] menu. For information about firmware compatibility with MTX-MRX Editor, refer to the Yamaha Pro Audio website. http://www.yamahaproaudio.com/japan/ja/ Synchronize your computer and the devices (put them in the online state).
Chapter 1. Workflow An overview of MTX-MRX Editor Edit the MTX’s ports and the XMV’s parameters If you assigned channels of an external device or ports of an MTX unit to channels when making internal MTX patch settings as described above, you can click the parameter recall button of that port or external device to open an edit screen for those parameters. For details, refer to “MAIN” screen if you’re using the MTX. If you’re using the MRX, refer to the “MRX Designer User Guide.
Chapter 1. About the screens An overview of MTX-MRX Editor About the screens MTX-MRX Editor consists mainly of the Project screen and the System screen. ❑ Project screen In this screen you can manage the MTX/MRX system. You can check the status of the MTX and XMV units, and make device-related settings. You can also check devices that have generated an alert. ❑ System screen In this screen you can make channel, matrix, and effect settings.
Chapter 1. Moving between screens An overview of MTX-MRX Editor Moving between screens Project screen Dialog boxes (*1) Toolbar or menu Toolbar or menu SYSTEM tab [Project] tab “EXT. I/O” screen System screen (“MAIN” screen or “MRX Designer” window) (*2) “EXi8” screen [EXT.
Chapter 2. Menu bar and tool buttons This chapter provides an overview of the menu bar and the tool buttons. For details on the various dialog boxes, see the linked references. Menu bar Title bar Tool buttons Title bar This will indicate “MTX-MRX Editor.” The name of the currently open project file is shown at the right of this. If you have opened a new project file or if the project file has never been saved, nothing will be shown here.
Chapter 2. Menu bar and tool buttons Menu bar Menu [File] Command Summary Dialog box that appears [New] Creates a new project file. If you are currently editing a project file, a confirmation message will appear. This command is not available while online. “Device Configuration Wizard” dialog box [Open] Opens a saved project file. If you are currently editing a project file, a confirmation message will appear. This command is not available while online.
Chapter 2. Menu bar and tool buttons Menu bar Menu [System] View Command Summary Dialog box that appears [Network Setup] Selects the computer’s network adapter that will be used to communicate with the MTX/MRX. You can also change the IP address of the network adapter. “Network Setup” dialog box [Device Information] Lists the devices on the network, allowing you to update their firmware and change their IP address.
Chapter 2. Menu bar and tool buttons Menu bar Menu [Controller] [About] Command Summary Dialog box that appears [External Events] Enables you to configure the commands to be transmitted so that you can control peripheral devices via the network to which the Dante connector or NETWORK connector is connected. “External Events” dialog box [Digital Control Panel] Makes settings for the digital control panel (DCP).
Chapter 2. Menu bar and tool buttons Tool buttons Tool buttons File-related tools Related tools Buttons etc. [New] [Open] File Preset-related tools Synchronization-related tools Summary Creates a new project file. If you are currently editing a project file, a confirmation message will appear. This button is not available while online. “Device Configuration Wizard” dialog box Opens a saved project file. If you are currently editing a project file, a confirmation message will appear.
Chapter 2. Menu bar and tool buttons Tool buttons Related tools Buttons etc. Online indicator [Online] Summary Dialog box that appears This will light if the devices and the computer are online. The color of the indicator will change according to the status. The indicator is shown for each MTX/MRX system. Blue ......when all devices assigned in the MTX/ MRX system are online. Yellow ...when at least one of the devices assigned in the MTX/MRX system is offline Unlit ......
Chapter 3. Project screen In this screen you can manage projects. When MTX-MRX Editor starts up, this screen will appear first. Use the tabs to switch between the Project screen and the System screen. Network devices MTX/MRX system System selection tabs [System] tab, [Device] tab, [Alert] tab HIDE/SHOW button ❑ System selection tabs Use these to select the MTX/MRX system that will be controlled by MTX-MRX Editor.
Chapter 3. Project screen Network devices Network devices This lists the devices existing on the same network as the computer. (Devices assigned to the MTX/ MRX system are not shown.) List of network devices Scroll buttons Identify button List of network devices These are the devices existing on the same network. The UNIT ID, device name, and a graphic of the device are shown.
Chapter 3. Project screen MTX/MRX system MTX/MRX system [Device Config] button YDIFconnected devices Digital control panel and PGM1/PGX1 Analogconnected devices DANTEconnected devices [Device Config] button When you click this, the “Device Configuration Wizard” dialog box will appear.
Chapter 3. Project screen “Device Configuration Wizard” dialog box ❑ “Device Configuration Wizard” dialog box In this dialog box, you’ll use the wizard to create or edit the configuration (structure) of the MTX/ MRX system. You can easily specify or edit the type of devices and the order in which they are connected. Here we will explain the dialog box that appears when you click the [Device Config] button in the Project screen.
Chapter 3. Project screen “Device Configuration Wizard” dialog box • [Finish] button This can be selected if you have selected something other than the [New] option button. When you click this, a confirmation message will appear; click the [Yes] button to clear the data and end the wizard. If you click the [No] button, the operation will be cancelled, and you will return to the previous dialog box. 2. From the devices that have already been assigned, delete any that you do not need.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 3. Specify the type and number of devices that will be assigned to the MTX/MRX system. Determine the number of devices that will be connected via cable, other than digital control panels. If you selected [Edit Configuration] in the first screen of the wizard, the currentlyassigned number of devices is shown.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 4. Specify the UNIT ID of each device. Specify the UNIT ID of each assigned device. Set the UNIT ID so that there is no conflict between devices. If you selected [New] in the first screen of the wizard, the devices will be numbered automatically starting from the lowest UNIT ID. If you selected [Edit Configuration], the currently-specified UNIT ID will be shown. In either case you are free to make changes.
Chapter 3. Project screen “Device Configuration Wizard” dialog box • [Next >] button Applies the changes and proceeds to the next screen. • [Finish] button This button will be dimmed and unavailable. 5. View a configuration diagram that shows the connections necessary for control via MTX-MRX Editor. Make settings for the device as directed by the dialog box. • [Cancel] button Cancels the operation and exits the wizard. • [< Back] button Returns to the previous screen.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 6. Specify the order of the YDIF-connected devices. Identify button You can drag and drop to change the connection order of the YDIF-connected devices. • [Identify] button When you click this, the indicator of the corresponding device will flash for approximately five seconds, allowing you to identify the device. This is not shown if no device is connected. • [Refresh] button Searches again for devices on the network.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 7. Specify the number of PGX1 units, and associate MTX5-D/MRX7-D and PGM1 units. (If PGM1 is set to other than 0 in step 3.) Here you can specify the number of PGM1 units which are extension units of the PGM1. You can also associate MTX5-D or MRX7-D units with PGM1 units, and specify the mic that is assigned as the 1st Priority Mic for the associated MTX5-D or MRX7-D.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 8. Select the Mini-YGDAI card that is inserted in the slot. (Only if a device that has a slot is included in the MTX/MRX system.) In the case of the MRX, use MRX Designer to assign a SLOT component. • Card selection box Select the Mini-YGDAI card that is inserted in the slot. NOTE If the inserted Mini-YGDAI card is being operated in emulation mode, select the card that is being emulated.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 9. Make configuration settings for digital control panels (DCP). Select the DCP units that you want to connect to the MTX/MRX. You’ll make settings individually for each MTX/MRX unit. As desired, you can assign a name to each DCP unit. DCP units can also be connected in a star topology by using the Yamaha DCH8 digital controller hub. • [Device] box Select the MTX/MRX unit to which you want to connect DCP units.
Chapter 3. Project screen “Device Configuration Wizard” dialog box 10. The “Configuration Diagram” dialog box will appear. A configuration diagram of the system you constructed using the wizard is shown. Following the directions in the dialog box, connect each device and specify the panel ID of each DCP. You can use the [Print] button to print this configuration diagram for convenient reference when you’re working at the actual location.
Chapter 3. Project screen YDIF-connected devices ❑ YDIF-connected devices List of YDIF-connected devices Identify button List of YDIF-connected devices These are the YDIF-connected devices within the MTX/MRX system. An online indicator, the UNIT ID, the device type, and a graphic of the device are shown. If you double-click the graphic of a device, the description of the DIP switches (or the device setting DIP switches for the XMV) will be shown.
Chapter 3. Project screen YDIF-connected devices The currently-selected device is enclosed by a blue border. Indication Online indicator Device icon Status Unlit Dimmed Does not exist on the network, or is not connected to the computer (MTX-MRX Editor). Lit blue Indication Exists on the network, and is synchronized with MTX-MRX Editor (online status). Lit green Exists on the network, but is not “Offline” indicated synchronized with MTX-MRX Editor (offline on the icon status).
Chapter 3. Project screen Digital control panel, PGM1/PGX1 ❑ Digital control panel, PGM1/PGX1 Digital Control Panel/PGM1 switching button Identify button List of connected devices This area shows an illustration and panel ID for each of the digital control panel (DCP) units and PGM1/PGX1 units assigned by the wizard. Up to eight DCP units can be connected to one MTX/ MRX unit. Up to four PGM1 units can be connected to one MTX/MRX system. The PGM1 can control only a single MTX5-D/MRX7-D unit.
Chapter 3. Project screen Analog-connected devices ❑ Analog-connected devices List of analogconnected devices Identify button Scroll buttons Of the devices controlled by MTX-MRX Editor, this area shows the devices whose audio signals are connected via analog. List of analog-connected devices This shows the XMV units within the MTX/MRX system that are connected to the MTX/ MRX via an analog connection.
Chapter 3. Project screen DANTE-connected devices ❑ DANTE-connected devices List of DANTEconnected devices Identify button Scroll buttons Of the devices controlled by MTX-MRX Editor, the Dante units other than the MTX/MRX or PGM1 are shown here. List of Dante-connected devices These are the Dante units within the MTX/MRX system, except for the MTX/MRX and PGM1. An online indicator, the UNIT ID, the device type, and a graphic of the device are shown.
Chapter 3. Project screen MCP1 ❑ MCP1 Identify button MCP1 list Scroll buttons Of the devices controlled by MTX-MRX Editor, the MCP1 units are shown here. MCP1 list These are the MCP1 units that are connected within the MTX/MRX system. An online indicator, the UNIT ID, the device type, and a graphic of the device are shown. For details on the online indicator, refer to YDIF-connected devices.
Chapter 3. Project screen [System] tab [System] tab This shows information about the MTX/MRX system. ● [SYSTEM NAME] This shows the system name that you entered in the [SYSTEM NAME] input box of the “Device Configuration Wizard” dialog box. If you want to change this, click the [Device Config] button and make changes in the “Device Configuration Wizard” dialog box. ● [YDIF MODE] This shows the YDIF connection mode that you specified as the [YDIF MODE] in the “Device Configuration Wizard” dialog box.
Chapter 3. Project screen [Device] tab [Device] tab When you click a device other than a digital control panel, information for that device is shown. For the MTX3/MTX5-D/MRX7-D For the EXi8/EXo8 For an XMV For the PGM1/MCP1/R series (AD/DA)/Tio1608-D ● [DEVICE TYPE] Indicates the type of device. ● [DEVICE NAME] Indicates the device name. You are free to assign a desired name. ● [UNIT ID] Indicates the UNIT ID.
Chapter 3. Project screen [Device] tab ● [SLOT] (MTX5-D/MRX7-D only) Indicates the Mini-YGDAI card specified in the “Device Configuration Wizard” dialog box. The [SRC] button is shown if an MY4-AEC or MY8-AE96S is selected. Click this to open the “Sampling Rate Converter” dialog box. ● [INPUT SOURCE] button (XMV only) For each channel, this indicates whether the input is analog or digital. When you click this, the “Input Source/Redundant” dialog box will appear.
Chapter 3. Project screen [Alert] tab [Alert] tab Alert notifications from a device are shown by a popup window in MTX-MRX Editor (see “Alert list”). Even if you close this popup window, you can use this tab to view alerts that have occurred in the past. The R-series (AD/DA) and Tio1608-D are excluded. ● [Show alert popup] check box If this is selected, a popup window will appear when alert notifications are received from a device. ● [Get Log From Devices] button The “Get Log” dialog box will appear.
Chapter 4. System screen This screen shows the audio signal flow within the MTX/MRX system. From this screen you can move to other editing screens.
Chapter 4. System screen Screen select buttons Screen select buttons Use these buttons to switch between units in the MTX/MRX system and to access various functions. ● [MTX]/[MRX] buttons Use these buttons to select the MTX/MRX unit whose settings you want to edit. The button shows the UNIT ID and device name. There will be one [MTX]/[MRX] button for each MTX/MRX unit in the MTX/MRX system. In the “MRX” screen, click the [Open MRX Designer] button to access the “MRX Designer” window.
Chapter 4. System screen Explanation of basic operation Explanation of basic operation Changing the screen size By dragging the right edge of the screen you can change the horizontal width of the screen. If you’re using a large monitor, this is a convenient way to view numerous channel strips simultaneously. By dragging the scroll bar in the center of the screen to the left or right, you can change the proportion of input channel faders and output channel faders that are shown.
Chapter 4. System screen “MAIN” screen “MAIN” screen This screen shows the input/output channels. From here you can access various editing screens. The types of channel and the number of channels are as follows.
Chapter 4. System screen Input channels Input channels Input channel settings are made in the [INPUT CHANNEL SETUP] section of the “MTX Configuration” dialog box. The description in this section assumes that two mono channels are used. If stereo channels are used, some settings will be shared between channels. 1 2 3 4 5 6 1 Channel index Shows the MTX’s input channel number. 2 Port select button Opens the “Input Patch” dialog box. The button shows the currently selected port.
Chapter 4. System screen Input channels Parameter edit screen (for the EXi8) A Meter Shows the input signal level. B [+48V] button A B C D E F G H I J K Turns the HA phantom power (+48V) on/off. Notice Be sure to leave this button off if you do not need phantom power. Follow the important precautions below, in order to prevent noise and possible damage to external devices as well as the unit when you operate this switch.
Chapter 4. System screen Input channels Parameter edit screen (for the R series (AD/DA) except the Ro8-D) A Meter Shows the input signal level. A B C D E F G H I J B [+48V] button Turns the HA phantom power (+48V) on/off. Notice Be sure to leave this button off if you do not need phantom power. When turning phantom power on, you must observe the precautions below in order to prevent noise and possible damage to the unit and to external devices.
Chapter 4. System screen Input channels Parameter edit screen (for the Tio1608-D) A Meter Shows the input signal level. A B C D E F G H B [+48V] button Turns the HA phantom power (+48V) on/off. Notice Be sure to leave this button off if you do not need phantom power. When turning phantom power on, you must observe the precautions below in order to prevent noise and possible damage to the unit and to external devices.
Chapter 4. System screen Input channels 4 “GAIN/HPF/EQ” screen access button Switches to the “GAIN/HPF/EQ” screen. The button also shows the on/off status. 5 EQ/HPF indication This shows a miniature (non-editable) version of the graph that is shown in the “GAIN/HPF/EQ” screen. This is not shown if HPF and EQ are off. 6 “GATE” screen access button 7 “COMP” screen access button Switches to the “GATE/COMP” screen. The button also shows the current value and on/off status.
Chapter 4. System screen Input channels ● Component copy Drag (left-click and move) the component that you want to copy, and drop it (release the right-click) on the desired channel. Alternatively, you can right-click a component to access a menu. Select [Copy] and then select [Paste] for the desired channel. NOTE The following components can be copied: GAIN/HPF/EQ, GATE/COMP, AGC, GAIN/EQ, COMP/AGC, DELAY/ROOM EQ, and SPEAKER PROCESSOR. However of [GAIN/HPF/EQ], [Ø] is not copied.
Chapter 4. System screen Stereo input channels Stereo input channels Stereo input channel settings are made in the [INPUT PORT SETUP] section of the “MTX Configuration” dialog box. Input channel settings are made in the [INPUT CHANNEL SETUP] section of the “MTX Configuration” dialog box. The description in this section assumes that STEREO channels are used. 1 2 1 Channel index Shows the MTX’s input channel number. 3 2 Port select button Opens the “Input Patch” dialog box.
Chapter 4. System screen Effect return channels Effect return channels 1 Effect return volume This parameter specifies the amount of audio signal processed by the effect that will be returned. For details on adjusting the following parameters, refer to Input channels. • Channel index • [ON] button • Fader/meter • Channel name 1 Direct input channels Direct input channel settings are made in the [INPUT CHANNEL SETUP] section on the [INPUT] tab of the “MTX Configuration” dialog box.
Chapter 4. System screen Output channels Output channels 1 2 1 Channel index Indicates the number of the MTX’s output channel. 3 2 Port select button Opens the “Output Patch” dialog box. The button shows the currently selected port. If more than one port is assigned, a [+] is shown at the end of the port name.
Chapter 4. System screen Output channels Parameter editing screen An output can be assigned to more than one device. In the explanatory screens shown here, the assignments are as follows. Upper line Lower line Left MTX [OUTPUT] connector parameters Center MTX [DANTE] parameters Right MTX [SLOT] parameters Left EXo8 parameters Right XMV parameters The popup shows the MTX [OUTPUT] connector parameters if OUTPUT is selected in the “Output Patch” popup.
Chapter 4. System screen “Input Patch” dialog box ❑ “Input Patch” dialog box Here you can specify the connector or channel whose signal will be assigned to each input channel. • [Input CH] box Selects the input source channel. • INPUT These are the MTX’s [INPUT] connectors. • ST IN These are the MTX’s [ST IN] connectors. • SD IN This is the MTX’s SD memory card. • YDIF This is the MTX’s [YDIF] connector. • DANTE (MTX5-D only) This is the MTX5-D’s [Dante] connector.
Chapter 4. System screen “Output Patch” dialog box ❑ “Output Patch” dialog box Here you can choose how the output channels will be assigned to connectors or channels. You can select multiple output connectors (except for Far-end Voice, and To Far-end). • [Output CH] box Selects the output channel. • OUTPUT These are the MTX’s [OUTPUT] connectors. • YDIF There are the channels that the MTX will output as YDIF. They are available only in Distribution mode.
Chapter 4. System screen “INPUT” screens “INPUT” screens In these screens you can apply signal processing to the input channels. In this screen you can apply signal processing to the input channels. You can apply GAIN/HPF/EQ, GATE/COMP, FBS/AGC, and Dugan Automixer. ● Channel selection Left button Use the left or right button to select the channel to which you want to apply signal processing.
Chapter 4. System screen “INPUT” screens ● Operations common to the “INPUT” screens For details on the knobs and numeric boxes, refer to Explanation of basic operation. HINT You can copy channel settings to other channels. When you right-click within the area, a list box will appear. Select a channel, and paste the settings (the Phase setting of an input channel will not be copied).
Chapter 4. System screen “GAIN/HPF/EQ” screen Input channels Signal flow INPUT CHANNEL(CH1-16) EQ OUT METER DIGITAL GAIN HPF 3BAND EQ GR GR GATE COMP POST ON METER LEVEL FBS* AGC* INSERT D ON A.Mixer* C A * CH 1-8 only * CH 1-8 only To SLOT OUT INSERT OUTPUT From SLOT IN INSERT INPUT “GAIN/HPF/EQ” screen In this screen you can edit the GAIN, HPF, and EQ parameters. 2 1 3 4 1 EQ graph and OUT meter The effect of the equalizer is shown as a graph.
Chapter 4. System screen “GAIN/HPF/EQ” screen 4 EQ setting area • EQ [ON] button Switches the EQ on/off. • [FLAT] button Resets the EG gain (0 dB). A confirmation message will appear. Click the [Yes] button to execute. • [Type] list box Select the type of EQ. The frequency response is shown by the EQ graph. PEQ (Parametric Equalizer) The volume in the region of the specified frequency will be boosted or cut according to the specified Q. L.
Chapter 4. System screen “GATE/COMP” screen “GATE/COMP” screen In this screen you can adjust the GATE and COMP (Compressor) parameters. 1 2 3 1 IN meter This is the input meter for the gate. 2 GATE setting area This type of signal processing passes the audio signal only while it exceeds a specified volume. Use this to cut low-level noise, such as when there is no input from a mic, or when the input is below a specified level (the threshold value).
Chapter 4. System screen “GATE/COMP” screen 3 COMP setting area This type of signal processing compresses the dynamic range. Use this to prevent problems that can occur in the sound if the input exceeds a certain level (threshold). • COMP graph The effect of the compressor is shown by this graph. The horizontal axis is the input signal level, and the vertical axis is the output level. • GR meter Indicates the amount of gain reduction. • COMP [ON] button Turns the compressor on/off.
Chapter 4. System screen “FBS/AGC” screen “FBS/AGC” screen In this screen you can edit the “FBS (Feed Back Suppressor)” and “AGC (Auto Gain Controller)” parameters. 1 2 1 FBS setting area FBS (Feed Back Suppressor) is a function that prevents the unpleasant acoustic feedback that occurs when sound from a speaker is picked up by a mic and reamplified. In addition to being unpleasant, acoustic feedback places a strain on the speakers, and can damage them.
Chapter 4. System screen “FBS/AGC” screen Performing FBS detection for the FIXED type In order to obtain good results, you should set up the mics, speakers, and other sound equipment, and adjust the output EQ settings before performing detection. If you want, FIXED can also be used in conjunction with DYNAMIC. 1. Adjust the power amp output volume. While vocalizing into the mic, gradually raise the power amp output to the volume at which the system will be operated in actual use.
Chapter 4. System screen “FBS/AGC” screen 2 AGC setting area AGC (Auto Gain Controller) is a function that automatically compensates the gain according to the input level, keeping a constant output level for an incoming signal whose level is changing. For example, differences in how closely and how loudly a person is speaking into a mic can make their amplified voice vary in volume, making it less intelligible. In such cases, the volume will be automatically adjusted within a fixed range.
Chapter 4. System screen “DUGAN AUTOMIXER” screen “DUGAN AUTOMIXER” screen In a system used for unscripted speech, the automixer detects the mics that are in use and automatically optimizes the gain distribution, maintaining a consistent system gain between multiple mics without requiring an engineer to be constantly adjusting the faders. The Dugan Automixer provided by the MTX automatically adjusts the automix gain of input channels 1–4 on the MTX3 or input channels 1–8 on the MTX5-D.
Chapter 4. System screen “DUGAN AUTOMIXER” screen 2 [meters] button Switches the meter display of the channel control field between gain/input/output. NOTE When using [weight] to adjust the relative sensitivity between the input channels, switching the meter display to “gain” lets you use the channel control field to adjust the gain amount, providing better visibility. 3 [OVERRIDE] button This function instantly mutes all mics except for a specific mic, such as the mic of the chair or head.
Chapter 4. System screen “DUGAN AUTOMIXER” screen 3 [weight] slider Adjusts the relative sensitivity between input channels. Set the meter display to “gain,” and adjust the weight setting so that the meters are at approximately the same level when there is no input. For example if noise is heard near a certain mic (e.g., air conditioner wind noise), lowering the weight value of that channel will reduce the noise.
Chapter 4. System screen Stereo input channels Stereo input channels Signal flow STEREO INPUT CHANNEL(STIN1L-3R) POST EQ METER DIGITAL GAIN 3BAND EQ GR COMP* LEVEL AGC* POST ON METER D ON C A * CH 1L-2R only “GAIN/EQ” screen In this screen you can adjust the GAIN and EQ parameters. For details on these parameters, refer to “GAIN/HPF/EQ” screen. “COMP/AGC” screen In this screen you can adjust the COMP and AGC parameters.
Chapter 4. System screen “MATRIX” screen “MATRIX” screen This screen mixes and sends the input channel signals. In SENDS ON FADER mode, you can use the input channel faders to adjust the amount of the input channels that is sent to the matrix bus. 3 1 4 2 5 6 Signal flow MATRIX 1 2 ... 7 8 ...
Chapter 4. System screen “MATRIX” screen 2 Matrix bus select buttons Select the matrix bus to which the signal will be sent. A pair of channels that are assigned as stereo is shown by a single button. If you right-click the button, you’ll be able to set all send levels to the matrix bus in a single operation by choosing 0 dB, –3 dB, –6 dB, or –Infinity. 3 Input channel matrix Shows the send level of each channel.
Chapter 4. System screen “MATRIX” screen NOTE • When sending from a stereo input to a stereo bus, you can use “MTX Configuration” dialog box in the “Advanced Settings” dialog box to switch between PAN and Blend. If Blend is selected, the controller and numeric value are not shown (illustration at right). • In the numeric box, enter [L63] or [l63] to pan fully left; enter [R63] or [r63] to pan fully right. Enter [C] or [c] to pan to the center.
Chapter 4. System screen “MATRIX” screen Setting the input channel mix 1. Click the [SENDS ON FADERS] button. 2. Click a send-destination select button to select a send-destination bus. 3. Adjust the send level of each input channel. You can use the [ON] button to switch send on/off.
Chapter 4. System screen “ZONE” screen “ZONE” screen In this screen you can specify settings for the PGM1, and how input signal priority will control output signals.
Chapter 4. System screen “ZONE” screen 1 Output channel faders The colors of the faders are linked with the colors of the [ZONE] buttons in the “MATRIX” screen. • [ON] buttons Turn ZONE OUT on/off. • Faders Adjust the ZONE OUT level. You can right-click a fader knob and set the send level by selecting 0 dB or -Infinity. ● Screen selection By clicking a button, you can switch to the screen for making various settings.
Chapter 4. System screen “PAGING” screen (MTX5-D only) “PAGING” screen (MTX5-D only) In this screen you can make settings for the PGM1 paging station microphone. Paging refers to the function of broadcasting an announcement. For the workflow of making settings, refer to “Workflow for paging settings” in the appendix, or the “MTX Setup Manual.” The SD messages referred to here are standard-format announcements saved on the SD card of the MTX.
Chapter 4. System screen “PAGING” screen (MTX5-D only) 5 GAIN setting area Each knob resets to the default value if you click it while holding down the key. In this area, you can make settings related to the line shown in green in the flow depicted below. level PTT : On PTT : Off Program Output 0dB Mic Input SD Input Range Mic/SD Output –∞ time Attack Opening Chime Closing Release Chime • [RANGE] knob Specifies the Program value while the chime is sounding or while the PGM1 is broadcasting.
Chapter 4. System screen “PRIORITY DUCKER” screen “PRIORITY DUCKER” screen In this screen you can make ducker settings. The ducker is a function that temporarily reduces the input from one channel when an audio signal is input to another specified input channel, allowing the audio from the specified channel to be heard clearly. The priority order is as follows: “PRIORITY SOURCE” of the “1st PRIORITY” > “PRIORITY SOURCE” of the “2nd PRIORITY” > MATRIX Out signal.
Chapter 4. System screen “PRIORITY DUCKER” screen • [RANGE] knob Specifies the amount of attenuation applied when the ducker is active. This amount specifies how much of the main audio will remain, or whether it will be silenced. • [ATTACK] knob Specifies the time from when the priority source input signal exceeds the THRESHOLD until the ducker for the main signal reaches the amount of attenuation specified by the [RANGE] knob.
Chapter 4. System screen “ANC” screen “ANC” screen In this screen you can make settings for the “Ambient Noise Compensator” (subsequently called “ANC”). ANC is a function that boosts or attenuates the output signal from the MTX according to the level that is being input via an ambient noise detection mic. The ANC function provided by the MTX is a gap-type ANC that detects silent intervals such as between songs, detects the noise level during those intervals, and varies the level accordingly.
Chapter 4. System screen “ANC” screen 0 [MAX GAIN] knob Specifies the maximum amount by which the input signal level will be compensated. A [RESPONSE TIME] knob Specifies the response speed for level compensation. Making ANC settings Examples of use Example 1: In a location where a speech is being given, automatically adjust the volume of the zone up or down according to the level of ambient noise (e.g., crowd noise).
Chapter 4. System screen “ROUTER” screen “ROUTER” screen In this screen you can assign zone outputs to output channels. 1 5 2 3 4 Signal flow OSCILLATOR FREQ.
Chapter 4. System screen “ROUTER” screen 2 Router This router distributes the signals. Click a square in the grid to switch the output on/ off. If you right-click, a context menu will appear, allowing you to choose [All OFF] to turn all outputs off. On: Off: It is not possible to mix multiple zone outputs for output to a single output channel. 3 OSCILLATOR [ON] button If this is on, a oscillator signal will be output to the corresponding channel.
Chapter 4. System screen “OUTPUT” screens “OUTPUT” screens In these screens you can apply signal processing to the output channels. In this screen you can apply signal processing to the output channels. You can apply DELAY/ ROOM EQ, and SPEAKER PROCESSOR. ● Channel selection Left button Right button Channel index Channel name Use the left or right button to select the channel to which you want to apply signal processing.
Chapter 4. System screen “DELAY/ROOM EQ” screen ● Operations common to the “OUTPUT” screens For details on the knobs and numeric boxes, refer to Explanation of basic operation. HINT You can copy channel settings to other channels. When you right-click within the area, a list box will appear. Select a channel, and paste the settings. The signal from the router is processed by ROOM EQ and SPEAKER PROCESSOR.
Chapter 4. System screen “DELAY/ROOM EQ” screen 2 DELAY setting area In a sound system that includes multiple speaker units, it may appear to a listener that the voice of the person talking is originating from a nearby speaker unit, rather than from the person themself. In such cases, you can correct the perceived localization by delaying the audio to the distant speaker unit according to the distance between the speaker unit and the person who is talking.
Chapter 4. System screen “SPEAKER PROCESSOR” screen “SPEAKER PROCESSOR” screen In this screen you can view the response of the “SPEAKER PROCESSOR” parameters that are provided for adjusting the speakers; these parameters include APF (All Pass Filter), Horn EQ, and limiter. These parameters can be edited in the “ADVANCED” screen. ■ Pre-installed LIBRARY In the libraries that are preinstalled with MTX-MRX Editor, the limiter’s threshold value is the value when using a power amp whose voltage gain is 26 dB.
Chapter 4. System screen “SPEAKER PROCESSOR” screen • [DELAY] button Includes or removes the effect of the delay response from the crossover curve that is displayed. • [PEQ] button Includes or removes the effect of the PEQ response from the crossover curve that is displayed. ■ [PEQ GRAPH] tab PHASE PEQ Displays the PEQ phase response curve. If the signal type is 2-way, High and Low are displayed separately in different colors. LEVEL PEQ Displays the PEQ amplitude response curve.
Chapter 4. System screen “ADVANCED” screen “ADVANCED” screen In this screen you can make detailed “SPEAKER PROCESSOR” settings. If the signal type is 2-way, the parameters are displayed separately for HIGH and LOW. [HIGH] tab [LOW] tab In the “ADVANCED” screen, control points are shown on the LEVEL PEQ amplitude response curve of the “PEQ GRAPH.
Chapter 4. System screen “ADVANCED” screen AdjustGc (Adjustable Gc) Adjusts the Gc (gain at the cutoff frequency) in a range of –6 – +6dB. Setting this to –3dB will produce a Butterworth filter, and setting this to –6dB will produce a Linkwitz-Riley filter. The Gc knob will appear when you select this. Butrwrth (Butterworth) This is the most common response. The passed region is flat, and the gain at the cutoff frequency is –3 dB.
Chapter 4. System screen “ADVANCED” screen APF (All Pass Filter) This filter passes the signals of the entire frequency range, affecting only the phase. It is used mainly to correct the phase of the crossover region. For APF 1st, the phase will be rotated 90° at the specified frequency, and will be rotated in the range 0° to 180° when seen over the entire frequency range.
Chapter 4. System screen “EFFECT” screen “EFFECT” screen In this screen you can change the effect type and edit the effect parameters. 2 3 1 4 5 6 This screen lets you edit the effect that is sent from the input channels to the effect bus. You can specify the type (e.g., reverb or echo), the parameter value for that type, and the send level. Signal flow EFFECT EFFECT RETURN 1L-2R (FX RTN 1L-2R) LEVEL POST ON METER ON From FX1 MATRIX CROSS POINT To MATRIX(MONO) LEVEL ON EFFECT 1 To MTRIX1,3...
Chapter 4. System screen “EFFECT” screen 3 Effect type (shown only if SENDS ON FADER mode is on) This selects the effect type for each bus. You can choose one of the following four types. Reverb Hall ........... Reverb that simulates an expansive space such as a concert hall. Reverb Stage ......... Reverb that simulates a broad stage. Karaoke Echo ....... Echo designed for karaoke use. Vocal Echo ............ Echo designed specifically for stage vocals.
Chapter 4. System screen “DCA” screen “DCA” screen In this screen you can adjust the levels and mute settings of multiple channels. 6 7 1 2 3 4 8 In this screen, input channels can be assigned to eight DCA groups and eight mute groups, and zone outputs can be assigned to eight DCA groups and eight mute groups. DCA groups allow you to use a single fader to control the input levels or output levels of multiple channels. Mute groups allow you to switch multiple channels on/off together.
Chapter 4. System screen “DCA” screen 5 [MUTE] group master buttons (shown only if the [INPUT CH MUTE] button or [ZONE OUT MUTE] button is selected) These buttons turn each mute group on/off. 6 Assignment channel matrix This matrix lets you assign channels to DCA groups or mute groups. The group names are shown on the vertical axis, and the names of the channels that can be assigned are shown on the horizontal axis. Click an intersection to assign a channel to a group.
Chapter 4. System screen “I/O” screen “I/O” screen In this screen you can make settings related to the HA (head amp) of the MTX’s analog input, and for the MTX’s digital output. You can also make settings to specify whether a pilot tone is output from digital output. When the PILOT TONE [ON] button is on, a pilot tone is output to channels whose digital output’s [PT] button is on.
Chapter 4. System screen “I/O” screen 1 PILOT TONE [ON] button Turns the pilot tone function on/off. If this is off, a pilot tone is not output even if the [PT] button is on. 2 Freq. Indicates the center frequency of the pilot tone. This is fixed at 20 kHz. 3 [LEVEL] knob Specifies the level of the pilot tone. 4 Analog input settings area Here you can make settings for the HA (head amp) of the MTX’s analog input.
Chapter 4. System screen “MY4-AEC” screen “MY4-AEC” screen In this screen you can make settings for the MY4-AEC installed in the MTX5-D’s [SLOT]. This screen will not appear if any other card is installed or if no card is installed. NOTE For example settings, refer to “MTX5-D/MY4-AEC System Setup Manual.” In this screen you can make settings for the signals of the MY4-AEC. In a teleconferencing system, the local and remote environments are respectively called the Nearend and Far-end.
Chapter 4. System screen Common items From Far-end A From Far-end B From Far-end C From Far-end D From Far-end selection Far-end Voice A Far-end Voice B Far-end Voice C Far-end Voice D NR NR NR NR REFERENCE ON/OFF To Far-end 4 To Far-end 3 “To Far-end” screen To Far-end 2 To Far-end 1 FBS Near-end Mic. 2 FBS Near-end Voice 2 Near-end Mic. 1 AEC Reference signal Near-end Voice 3 FBS AEC NR Near-end Voice 4 Near-end Mic. 3 AEC NR NR Near-end Mic.
Chapter 4. System screen Common items ● From Far-end selection 1 2 3 Here you can select the channels to which input signals from the remote location will be output. 1 [From Far-end] signal selection buttons These open the “Input Patch” dialog box, where you can select the audio signals from the remote location (From Far-end). The button shows the currently selected port or channel.
Chapter 4. System screen “To Far-end” screen ❑ “To Far-end” screen In this screen you can make echo-cancel settings for the mics. The mic signal after echo-cancellation is output to the remote location. 1 AEC [ON] button Switches the echo canceller function on/off. 1 2 3 6 7 4 5 2 REFERENCE [A][B][C][D] buttons These buttons select whether the signal specified by the From Far-end selection will be used as the AEC reference signal (REFERENCE). If multiple signals are selected, they will be mixed.
Chapter 4. System screen “Near-end Voice” screen 6 [Distance] knob This specifies the distance between the installed mic and speaker in units of meters. If multiple mics and speakers are connected, specify the distance between the mic and speaker that are closest to each other. If the distance is 2 m or less, set this to 2. 7 [To Far-end] channel select button This button selects the output destination for the audio signals that are output to the remote location (Far-end).
Chapter 4. System screen “Mic” screen ❑ “Mic” screen When using a mic equipped with a PTT (Push To Talk) switch, a small amount of noise may be heard while the PTT switch is off. If this noise is input to the AEC, the AEC will mistakenly learn the noise, causing an echo when the PTT switch is turned on to resume speaking. In this screen you can make settings and specify the type of mic to prevent this from occurring.
Chapter 4. System screen “EXT. I/O” screen “EXT. I/O” screen Here you can select the signal routing for the MTX series and MRX series unit’s YDIF connectors and analog connectors. ❑ “YDIF” screen (Distribution mode) This screen appears in Distribution mode. 5 1 2 3 4 6 7 8 9 1 [YDIF 1-8] button Displays the “YDIF1-8” screen. Here you can specify the routing for YDIF channels 1– 8. 2 [YDIF 9-16] button Displays the “YDIF9-16” screen. Here you can specify the routing for YDIF channels 9–16.
Chapter 4. System screen “YDIF” screen (Distribution mode) 6 Input routing select buttons These buttons open the “YDIF In Patch” dialog box, where you can select the input source device and channels for the YDIF signal. To enable these buttons, click the [EDIT] button. NOTE • These settings are not included in the preset. For this reason, they can be edited only after clicking the [EDIT] button, in order to prevent the settings from being changed casually.
Chapter 4.
Chapter 4. System screen “YDIF In Patch” dialog box ❑ “YDIF In Patch” dialog box Here you can select the input channel for the YDIF signal. • [YDIF In:] box Select the YDIF channel that you want to edit. • Channel select buttons These buttons select the input channel. The device ID and model name of the input source are shown at the left. • [Close] button Closes the “YDIF In Patch” dialog box. ❑ “YDIF Out Patch” dialog box Here you can select the channels to which the YDIF signal will be output.
Chapter 4. System screen “Channel Select” dialog box ❑ “Channel Select” dialog box Here you can select the signals that are output from the MTX to YDIF. If nothing is selected, the signal will not be output to YDIF. For the MRX, the connection lines in the “MRX Designer” window determine the destination. • [YDIF:] box Select the YDIF channel that you want to edit. • [Thru] button The signals coming into YDIF input will be sent to the same YDIF channel without change.
Chapter 4. System screen “YDIF” screen (Cascade mode) ❑ “YDIF” screen (Cascade mode) This screen appears in Cascade mode. It indicates which MTX MATRIX bus is routed to which YDIF output. You can turn the YDIF outputs on or off in the [CASCADE MODE] section on the [OUTPUT] tab of the “MTX Configuration” dialog box.
Chapter 4. System screen “ANALOG” screen ❑ “ANALOG” screen Here you can select the XMV unit and the channels of the unit that will input analog audio signals. These settings let you control the parameters of analog-connected XMV units from the Parameter editing screen. However, audio routing settings cannot be made. 1 2 1 MTX/MRX select buttons Use these buttons to select the MTX/MRX unit that you want to edit.
Chapter 4. System screen “Line Out Patch” dialog box ❑ “Line Out Patch” dialog box Here you can specify the output destination device and channel for analog signal output from the MTX/MRX unit. You can select multiple output destinations. • [Out:] box Select the output channel that you want to edit. • Channel select buttons These buttons select the output destination device and channel. The device ID and model name of the output destination are shown at the left.
Chapter 4. System screen “DANTE” screen ❑ “DANTE” screen 1 2 3 4 5 1 [EDIT] button Turn this on to enable editing. 2 [Use the settings of Dante Controller] check box Select this check box if you’re using Audinate Corporation’s Dante Controller to set up the Dante network. The settings of Dante Controller will take priority over the settings made in MTX-MRX Editor. If this check box is cleared, you’ll be able to use MTX-MRX Editor to make Dante network settings within the project.
Chapter 4. System screen “DANTE” screen 5 Matrix Change the transmission/reception assignments by clicking the location at which an input channel and output channel intersect. The connection is on when the ● symbol is displayed. Devices for which Device Lock is specified by Dante Controller cannot be changed. If you execute Update Device Information which appears when you right-click, the Device Lock status and the Rio/Tio’s Dante Device Name are updated.
Chapter 4. System screen “EXi8” screen “EXi8” screen Here you can view and edit the parameters of the EXi8 units in the MTX/MRX system. When you right-click on the display area of a desired EXi8, a context menu appears, allowing you to copy and paste settings between devices. 1 2 3 4 6 8 9 0 75 1 [EDIT] button This enables the EXi8 output routing select buttons. NOTE The [EDIT] button is available only in the offline state.
Chapter 4. System screen “EXi8 Patch” dialog box 5 [Ø] button Switches the phase of the input signal. 6 [ON] button Switches the input channel on/off. The button also shows the on/off status. 7 [HPF] button/Cutoff frequency The [HPF] button switches the HPF (High Pass Filter) on/off. The cutoff frequency is shown below the [HPF] button. You can double-click the cutoff frequency to edit it. 8 HA analog gain Shows the HA analog gain setting. You can double-click this and edit it.
Chapter 4. System screen “R/Tio” screen “R/Tio” screen Here you can view and edit the parameters for the analog input jacks of an R series (AD/DA) or Tio1608-D unit. When you right-click on the display area of a desired R series (AD/DA) or Tio1608D, a context menu appears, allowing you to copy and paste settings between devices. NOTE Since the Ro8-D has no analog input jacks, it is not shown.
Chapter 4. System screen “R/Tio” screen 7 [HPF] button / Cutoff frequency The [HPF] button switches the HPF (High Pass Filter) on/off. The cutoff frequency is shown below the [HPF] button. You can double-click the cutoff frequency to edit it. 8 “GC” indicator / gain value Indicates the on/off status of the R series (AD/DA) unit’s gain compensation. If gain compensation is on, the gain value fixed by gain compensation is shown. 9 HA analog gain Shows the HA analog gain setting.
Chapter 4. System screen “EXo8” screen “EXo8” screen Here you can view and edit the parameters of the EXo8 units in the MTX/MRX system. When you right-click on the display area of a desired EXo8, a context menu appears, allowing you to copy and paste settings between devices. 1 3 2 4 5 6 7 8 1 [EDIT] button This enables the EXo8 input routing select buttons. NOTE The [EDIT] button is available only in the offline state.
Chapter 4. System screen “EXo8 Patch” dialog box ❑ “EXo8 Patch” dialog box Here you can select the output source channels for the audio signals of the EXo8 unit. • [YDIF] buttons Select the output source channel. • [Close] button Closes the “EXo8 Patch” dialog box.
Chapter 4. System screen “XMV” screen “XMV” screen Here you can view and edit the parameters of the XMV units in the MTX/MRX system. The units are grouped according to how they are connected: YDIF-connected, analog-connected, or Danteconnected. When you right-click on the display area of a desired XMV, a context menu appears, allowing you to copy and paste settings between devices.
Chapter 4. System screen “XMV” screen 6 5 7 8 9 E DC B A < 5 XMV identification area Shows the UNIT ID, model type, and model name of the corresponding XMV unit. 6 [POWER] If you click the [STANDBY] button, the power of the corresponding XMV unit will be switched to standby. If you click the [ON] button, the power of the corresponding XMV unit will be switched on.
Chapter 4. System screen “XMV Patch” dialog box D Attenuator Shows the XMV’s output attenuator setting. You can double-click this and edit it. E Channel name Indicates the channel name. You can double-click this and edit it. ❑ “XMV Patch” dialog box Here you can select the output destination device and channels for the audio signals of the XMV unit. The items shown will depend on the type of connections.
Chapter 5. Online and Synchronization You can connect the MTX/MRX to your computer and send the settings created using MTX-MRX Editor to the MTX/MRX, or synchronize the MTX/MRX with MTX-MRX Editor and edit the settings. You can also load data from the MTX/MRX into MTX-MRX Editor. The state in which the MTX/MRX and MTX-MRX Editor operate in synchronization is called the “online state.” The action of bringing them into this state is called “Synchronization.
Chapter 5. Online and Synchronization Online Procedure 1. In the toolbar, click the [Online] button. The “Synchronization” dialog box will appear, allowing you to choose the direction of synchronization. 2. Choose either [To Device] or [From Device] to specify the direction in which synchronization will occur. Click the [OK] button to switch to a display that lets you choose the system that will be synchronized. If you click the [Cancel] button, the operation will be cancelled.
Chapter 5. Online and Synchronization Online 5. The synchronization progress is displayed. If you click the [Abort] button, the operation will be halted. This can be a useful way to save time, for example if you’ve noticed a mistake during synchronization and want to edit a parameter. The settings will have been partially transmitted, so after you’ve made changes, be sure to complete synchronization to the end. Progress bar Message area • Progress bar Shows the status of synchronization.
Chapter 5. Online and Synchronization Online ❑ “Go online – From devices” dialog box The settings (configuration and parameters) of the MTX/MRX are loaded into MTX-MRX Editor. In order to execute this, the MTX/MRX whose settings are to be obtained must have been online with MTX-MRX Editor using the To Device setting. In this dialog box, you can specify how multiple MTX/MRX systems that are found will be assigned to SYSTEM #1 through #4.
Chapter 5. Online and Synchronization Synchronization Synchronization Synchronization includes the following three operations. 1) Synchronizing from the computer (MTX-MRX Editor) to the MTX/MRX unit itself The settings (configuration and parameters) of MTX-MRX Editor are sent to the MTX/ MRX. Use this method when you have prepared a file beforehand, and want to send those settings to the MTX/MRX on-site. In the “Synchronization” dialog box, choose [To Device].
Chapter 5. Online and Synchronization Synchronization • Case 2 The settings (configuration and parameters) of the MTX/MRX are loaded into MTX-MRX Editor. In order to execute this, the MTX/MRX whose settings are to be obtained must have been online with MTX-MRX Editor using the To Device setting. If there is no settings file in MTX-MRX Editor, you can use this method to obtain all of the configuration and parameter data from the MTX/MRX, and use MTX-MRX Editor to edit or check the parameters.
Chapter 6. Presets This chapter explains the presets which allow you to change multiple parameters in a single operation. Preset settings are made in the “Preset” dialog box which you can access by clicking the preset button in the toolbar. In this dialog box you can store the settings of multiple parameters as a preset, or recall a stored preset to apply its parameters to the current settings. The parameters of the preset that is applied are called the “current parameters.
Chapter 6. Presets “Preset” dialog box • [Name:] Input the name of the preset. By default, this will be “Preset + preset number.” You cannot enter a blank preset name. • [OK] button This stores the preset and closes the dialog box. • [Cancel] button This cancels the preset store operation, and closes the dialog box. ● [Recall] button When you click this button, the currently selected preset will be recalled (loaded) as the current parameters.
Chapter 6. Presets “Preset” dialog box • Scheduler ( ) If this check box is selected, the scheduler function will be enabled when the preset is recalled. NOTE If the scheduler is disabled, the [SCHEDULER] indicator of the MTX/MRX unit itself will flash rapidly when the event time occurs. • [MTX3]/[MTX5-D] If even one item is specified in the Recall Filter setting screen as excluded from recall, this area will indicate “ .” • [EXT.
Chapter 6. Presets “Preset” dialog box ● [Preset Link] button This displays the “Preset Link” dialog box where you can make settings for linking preset recall between MTX/MRX systems. ● [Power on Default] This specifies the preset that will be recalled when you turn on the power of the MTX/ MRX. If you want the unit to start up with the same settings each time, resetting any changes that were made, turn this on so that the preset you specified will be recalled at start-up.
Chapter 6. Presets “Preset” dialog box “Preset Link” dialog box Here you can make settings for linking preset recall between MTX/MRX systems. Linking does not occur between MTX/MRX systems that have different subnets. • Preset list This lists the preset names for each MTX/MRX system in the project. Select the check boxes of presets for which you want preset recall to be linked. • [All ON] button Selects the check boxes of all presets. • [All OFF] button Clears the check boxes of all presets.
Chapter 6. Presets “Settings” dialog box “Settings” dialog box Here you can specify the DCP library, Wireless DCP library, MCP1 library, GPI OUT, and SD memory card settings that will be recalled when the preset is recalled. [DCP Library]/[Wireless DCP Library]/[MCP1 Library] Here you can specify the library that will be recalled when the preset is recalled. If the [Assign] check box is selected, you’ll be able to select a library item.
Chapter 6. Presets “Settings” dialog box [GPI OUT] MTX/MRX select buttons [GPI OUT] pin number and status Here you can specify the GPI OUT settings that will be output when the preset is recalled. You can use GPI OUT output to control a device that’s connected to this unit’s [GPI OUT] connectors. • MTX/MRX select buttons Select the button of the MTX/MRX unit whose settings you want to change. (Each button shows the UNIT ID and device name.) This displays the “GPI Out” dialog box.
Chapter 6. Presets “Settings” dialog box • PLAY MODE The [Play Mode] setting of the “SD Play” dialog box is shown. [External Event] Here you can specify an event to be output when a preset is recalled. An event is output from the unit's NETWORK connector, or Dante [PRIMARY] or [SECONDARY] connector, or the communication circuit during the redundancy operation.
Chapter 6. Presets “Settings” dialog box “Settings (Output Port)” dialog box for “GPI” [OUTPUT TYPE] If [Active] is specified When [OUTPUT TYPE] is [ Closed], the [GPI OUT] pin will be closed (connected to ground). When [OUTPUT TYPE] is [ Open], the [GPI OUT] pin will be open. When [OUTPUT TYPE] is [ Pulse], the [GPI OUT] pin will be closed (connected to ground) for approximately 250 ms. When [OUTPUT TYPE] is [ Pulse Inv.], the [GPI OUT] pin will be open for approximately 250 ms.
Chapter 6. Presets “Settings” dialog box ■ “SD Play” dialog box Here you can specify a file that will be played when the preset is recalled. Each MTX/MRX unit can play one file or play all files in the same folder. If four MTX/MRX units are connected via YDIF, each MTX/MRX unit can play one file; i.e., a total of up to four files can be played by the system. If you want multiple songs to play, choose [Play all songs in a folder] in the [Folder/File] area, and specify the folder that contains those songs.
Chapter 6. Presets “Settings” dialog box If [Play 1 song] is selected Only the file currently selected in [SD CARD:/] will play. The following file and folder formats can be shown. • (folder name)\(file name).mp3 • (folder name)\(file name).wav • (file name).mp3 • (file name).wav If [Play all songs in a folder] is selected All files saved in the folder currently selected in [SD CARD:/] will play. The following folder formats can be shown. • (folder name) • blank NOTE - Only first-level folders are valid.
Chapter 6. Presets “Settings” dialog box Main usage method 1. Prepare the SD memory card. Copy the files that you want to play into the SD memory card. If you want to play multiple files, place them in a folder no deeper than the first level. 2. Insert the SD memory card you prepared in step 1 into the computer. 3. In [SD Song Select & Play], click the MTX/MRX select button for the unit into which you intend to insert the SD memory card. The “SD Play (MTX)” dialog box will appear. 4.
Chapter 6. Presets Recall Filter setting screen Recall Filter setting screen Here you can specify which parameters will be recalled when you recall a preset. For example if the input/output levels do not change for any of the presets, you can exclude the INPUT LEVEL and OUTPUT LEVEL from recall, so that the level settings can stay the same without your having to re-specify the levels for each preset.
Chapter 6. Presets Recall Filter setting screen ■ [PASTE] button Pastes the copied Recall Filter settings to the currently selected preset. The Paste command is not available while online. ■ [Apply] button Applies the currently-edited Recall Filter settings. If the settings have not been edited, this button will be unavailable and cannot be clicked. ■ [Close] button Closes the dialog box. ■ [MTX]/[MRX] tab Here you can choose the MTX/MRX unit for which to make Recall Filter settings.
Chapter 6. Presets Recall Filter setting screen • [IN PATCH] button If this is on, the input patch settings and input channel names will be recalled. These buttons include patching to the MY4-AEC input channels From Far-end, Farend Voice, Near-end Mic., Near-end Voice, and To Far-end. • [INPUT]/[LEVEL] buttons If the [INPUT] button is on, the following input channel settings will be recalled.
Chapter 6. Presets Recall Filter setting screen • [MATRIX SEND] button If the button at the left is on, the following settings will be recalled. • Send level from the input channel to the matrix bus, send on/off, and stereo channel pan • Send level from effect return to the matrix bus, send on/off, and stereo channel pan If the button at the right is on, the matrix out level will be recalled.
Chapter 6. Presets Recall Filter setting screen • [LEVEL]/[OUTPUT] buttons If the [LEVEL] button is on, the output channel level and on/off (mute) settings will be recalled. If the [OUTPUT] button is on, the Room EQ, Delay, and Speaker Processor settings will be recalled. These can be specified individually for each channel. • [OUT PATCH] button If this is on, the output patch settings and output channel names will be recalled.
Chapter 6. Presets Recall Filter setting screen ■ [External I/O] tab Here you can choose the external device parameters for which to make Recall Filter settings. ● [All On] button Turns on (blue) all of the buttons of the currently selected tab. All parameters will be recalled. ● [All Off] button Turns off (white) all of the buttons of the currently selected tab. None of the parameters will be recalled.
Chapter 6. Presets Recall Filter setting screen ■ [MCP1] tab Here you can choose the MCP1 unit for which to make Recall Filter settings. ● [MCP1] button If this is on, the parameter assignments of the MCP1 connected to the MTX will be recalled.
Chapter 7. Dialog boxes/Software applications This chapter explains the dialog boxes and applications that you can open from the menu bar or tool bar. ❑ “Startup” dialog box This will appear when you start MTX-MRX Editor. ● [New file] option button When you click the [OK] button, the “Device Configuration Wizard” dialog box will appear. ● [Existing file on computer] option button When you click the [OK] button, the selected file will open.
Chapter 7. Dialog boxes/Software applications “Network Setup” dialog box ❑ “Network Setup” dialog box Here you can select the network interface card of the computer that will be used to communicate with the MTX/MRX (subsequently called “the network card”). NOTE If you’re not using a DHCP server, fix the IP address of your computer’s network card. We recommend the following settings. IP address: 192.168.0.253 Subnet mask: 255.255.255.
Chapter 7. Dialog boxes/Software applications “Device Information” dialog box ❑ “Device Information” dialog box Lists the devices on the network, allowing you to update their firmware and change their IP address. ● Network Interface Shows the name/IP address/subnet mask of the network card currently selected in the “Select Network Interface Card” dialog box.
Chapter 7. Dialog boxes/Software applications “Device Information” dialog box • Battery Shows the remaining battery amount for a device that contains a battery. EMPTY: The remaining amount is 0–0.5V. Immediately stop using the unit, and contact a Yamaha service center. Low: The remaining amount is 0.5–2.5V. Contact a Yamaha service center as soon as possible. OK: The remaining amount is 2.5–3.5V. There is no problem. N/A: The device does not contain a battery.
Chapter 7. Dialog boxes/Software applications “Update Firmware” dialog box “Update Firmware” dialog box This dialog box lets you update the firmware of a unit such as an MTX/MRX or XMV. For Dante units such as the MTX5-D and the XMV8280-D, there may be cases in which the Dante firmware needs to be updated. For details on how to update the Dante firmware, refer to the “MTX/MRX system Firmware Update Guide.” NOTE • In some cases, updating may cause data to no longer be compatible.
Chapter 7. Dialog boxes/Software applications “Update Firmware” dialog box ● [Update] button Executes the update. If an update file does not exist in the selected folder, this button will be dimmed and unavailable. ● [Cancel] button Cancels the update and closes the dialog box. ■ Update procedure All applicable devices can be updated at the same time. NOTE If there is an MTX/MRX unit with an assigned PIN code that differs from the project, you’ll need to enter the PIN code. 1.
Chapter 7. Dialog boxes/Software applications “IP Address” dialog box “IP Address” dialog box Here you can set the device’s IP settings. As the device’s settings, we recommend that you set “IP SETTINGS” to “UNIT ID” or “STATIC IP (Auto),” and set the computer’s IP address to “192.168.0.253” and its subnet mask to “255.255.255.0.” Editing is not possible while online.
Chapter 7. Dialog boxes/Software applications “IP Address” dialog box 9. In the “Device Information” dialog box, click the [Refresh] button. Verify that the device’s IP address has been changed. HINT If you want to change the setting of multiple devices, repeat steps 3 through 5, and then proceed to step 6 and following. ● Device list Shows the devices on the network. When you click this, the settings of the current device are shown in the right, allowing you to edit them.
Chapter 7. Dialog boxes/Software applications “IP Address” dialog box The following subnet masks can be selected. 128.0.0.0 255.255.128.0 192.0.0.0 255.255.192.0 224.0.0.0 255.255.224.0 240.0.0.0 255.255.240.0 248.0.0.0 255.255.248.0 252.0.0.0 255.255.252.0 254.0.0.0 255.255.254.0 255.0.0.0 255.255.255.0 (default value) 255.128.0.0 255.255.255.128 255.192.0.0 255.255.255.192 255.224.0.0 255.255.255.224 255.240.0.0 255.255.255.240 255.248.0.0 255.255.255.248 255.252.0.0 255.255.
Chapter 7. Dialog boxes/Software applications “Auto-Assign IP Address” dialog box “Auto-Assign IP Address” dialog box Information such as the IP address assigned to devices placed in MTX-MRX Editor using the “Match Device by IP Address” dialog box is applied to the “IP Address” dialog box in a single operation. For details, refer to “Settings for controlling devices across subnets” in the appendix.
Chapter 7. Dialog boxes/Software applications “Match Device by IP Address” dialog box ❑ “Match Device by IP Address” dialog box Switches to a mode in which MTX-MRX Editor identifies devices on the network by their IP address. If you want to control an MTX/MRX system that is on a different subnet than MTX-MRX Editor, make settings here. For details on the procedure for settings, refer to “Settings for controlling devices across subnets”.
Chapter 7. Dialog boxes/Software applications “Match Device by IP Address” dialog box 1 2 3 4 5 6 7 1 [Distinguish devices by IP Address] check box If this check box is selected, devices are distinguished by their IP address, not their UNIT ID. 2 “IP Address Range Finder” area If it is OK for the IP addresses to be consecutive, you can use this to calculate the IP addresses for assignment. • [IP Address] Enter the IP address that you want to use. • [Subnet Mask] Select the subnet mask.
Chapter 7. Dialog boxes/Software applications “Match Device by IP Address” dialog box 4 System tabs Here you can view and edit the settings of the devices in the system. • [Subnet Mask] Select the subnet mask. For the subnet masks that can be selected, refer to the “IP Address” dialog box. • [Default Gateway] Enter the IP address of the default gateway within the subnet. • Device list Enter the IP address of the devices in the system.
Chapter 7. Dialog boxes/Software applications “MTX Configuration” dialog box ❑ “MTX Configuration” dialog box Here you can specify input/output settings for each device, such as MTX/MRX input ports, output channels, and matrix buses. NOTE Since these settings are not included in a preset, they cannot be changed via the Preset Recall function. ● Device: Selects an MTX unit within the MTX/MRX system.
Chapter 7. Dialog boxes/Software applications “MTX Configuration” dialog box ● [OUTPUT] tab In this tab, you can make settings related to outputs. • MATRIX BUS SETUP Here you can make settings for the matrix buses. These settings will affect the “MATRIX” screen. MONO x2...............The input channels will be treated as two monaural channels. STEREO .................The input channels will be treated as a single stereo pair.
Chapter 7. Dialog boxes/Software applications “MTX Configuration” dialog box “Advanced Settings” dialog box Here you can specify the matrix pan mode (PAN or Blend). For both input and output, this can be specified only for stereo. If you choose [Blend], the right and left channels of the stereo audio will be mixed while preserving the sense of stereo.
Chapter 7. Dialog boxes/Software applications “Dante Information” dialog box ❑ “Dante Information” dialog box This shows Dante-related settings for Dante units such as the MTX5-D or XMV8280-D. ● [Preserve the Dante settings configured by Dante Controller] check box Select this check box if you’re using Audinate Corporation’s Dante Controller to set up the Dante network. The settings of Dante Controller will take priority over the settings made in MTX-MRX Editor.
Chapter 7. Dialog boxes/Software applications “Word Clock” dialog box ❑ “Word Clock” dialog box Here you can edit the word clock settings of the MTX/MRX system. Normally, these will be set to the optimal values when you use the “Device Configuration Wizard” dialog box to create the configuration. If you want to specify a Mini-YGDAI card as the word clock master etc., make settings in this dialog box.
Chapter 7. Dialog boxes/Software applications “Word Clock” dialog box Icon Clock source Dante Internal Mini-YGDAI card YDIF None NOTE The following devices are not shown. • • • • EXi8 Exo8 XMV units connected via YDIF XMV units connected via analog ● [Device Word Clock Fs:] This indicates the word clock of the device. When online, this indicates the word clock value for the device. When offline, the indication will be as follows.
Chapter 7. Dialog boxes/Software applications “Clock” dialog box ❑ “Clock” dialog box The date and time of the computer are transmitted to each device connected to the MTX/MRX system every time it goes online, automatically updating the internal clock of each device. If you transmit the computer’s date and time information from this dialog box, the date and time will be updated on an MTX/MRX unit that is connected to the same network, regardless of online/offline status.
Chapter 7. Dialog boxes/Software applications “Clock” dialog box ● [Synchronize with a system clock in this computer] option button If you select this option, the date and time of the computer’s system clock will be sent out each time the system comes online, and the internal clock on the MTX/MRX will be automatically updated. • [Time] Shows the date and time of the computer system clock, ignoring the daylight saving time setting.
Chapter 7. Dialog boxes/Software applications “Daylight Saving Time” dialog box ❑ “Daylight Saving Time” dialog box This specifies the daylight saving time setting of the MTX/MRX devices connected to the same network, regardless of their online/offline state. NOTE • Events that are assigned within two hours before or after the beginning or end of daylight saving time in the “Scheduler” dialog box will not be executed correctly.
Chapter 7. Dialog boxes/Software applications “Daylight Saving Time” dialog box ● Start Day Indicates the date on which daylight saving time starts for the device. ● End Day Indicates the date on which daylight saving time ends for the device. ● [Enable Daylight Saving Time] check box Daylight saving time will be enabled if this check box is selected.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box ❑ “Scheduler” dialog box You can switch presets or play back a song or sound effect from an SD memory card at a previously specified date and time. Each such setting is called an “Event.” Switching background music by time period Here’s how you could switch the type of background music according to the time period, for example in a commercial establishment.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box You can assign up to 50 events and 50 exceptions. ● [Month] button/[Day] button Switch the calendar between month or day views. Month view Day view • In the calendar, double-click the date you want; the “Add Event” dialog box will appear, letting you add an event.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box ● [ < ]/[ > ] buttons For the month view, displays the previous or next month’s calendar. For the day view, displays the previous or next day’s schedule. ● Event Control • [Add] button The “Add Event” dialog box will appear. Here you can add an event. • [Edit] button The “Edit Event” dialog box will appear. Here you can edit the contents of the currently selected event. If no event is selected, the button is dimmed.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box “Add Event” dialog box / “Edit Event” dialog box For details about settings that are unique to the MRX series, refer to “MRX Designer User Guide.” ● EVENT NAME Enter the name of the event. ● EVENT OPERATION • [Type] box Choose the operation that will be executed when the event occurs. NOTE In the “Preset” dialog box operations such as GPI Out or SD Song Select & Play can be included in the preset.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box • Settings The contents will change depending on the event you chose in [Type] box. If you chose Preset Recall Select the preset that you want to recall. If you chose GPI Out Specify the state of the GPI OUT connector when the event occurs for each MTX/ MRX unit. Click the button of the MTX/MRX unit that you want to set; the “GPI Out” dialog box will appear.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box If you chose Paging For each MTX/MRX unit, specify the ZONE/ZONE GROUP to which message files saved on the SD memory card will be broadcast when the event occurs. Click the button of the MTX/MRX unit that you want to set; the “SD Message Select” dialog box will appear. To use the Paging function, use the “ZONE” screen to specify the Paging and Zone Group, and use the “PGM1/PGX1” dialog box to specify chime and other settings.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box ● [REPEAT EVENT] By selecting this check box you can specify a repeating event. • [Yearly]/[Monthly]/[Weekly]/[Daily]/[Hourly] boxes Specify the frequency with which the event will occur. • Event start date and time Specify the date and time at which the event will occur repeatedly. The items that you can specify will depend on the frequency of the event.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box ● [Exception] button The “Event Exception” dialog box will appear. Here you can specify a date and time for which, as an exception, the repeating event will not occur. ● [OK] button Saves the settings and closes the dialog box. ● [Cancel] button Closes the dialog box without saving the changes. ■ “Event Exception” dialog box Here you can specify a date and time for which, as an exception, the repeating event will not occur.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box If the event frequency is [Hourly] Specify the month, week, day, day of the week, or time (in hours) for which the event will not occur. The [Month], [Week], [Day], [Day of the week], and [Hour] can be specified. ● [>] button Adds a date and time that you want to specify as an exception to the list at the right. ● [<] button Removes a date and time that you specified as an exception from the list at the right.
Chapter 7. Dialog boxes/Software applications “Scheduler” dialog box ● [No Assign] option button If this is selected, no broadcast is made when the event occurs. ● [Play] option button If this is selected, a broadcast is made when the event occurs. ● SD CARD:/ This indicates the selected message file. ● [Browse] button When you click this, a screen will appear, allowing you to select a message file. ● [Zone]/[Zone Group] These specify the Zone(s) and Zone Group(s) to which the broadcast is made.
Chapter 7. Dialog boxes/Software applications “Remote Control” dialog box ❑ “Remote Control” dialog box Here you can check the port numbers for connecting an external controller, or make settings for connecting an external controller to RS-232C. NOTE • A total of nine external controllers and wireless DCP units can be connected to a single MTX/MRX. • The IP address of the MTX/MRX can be viewed in the “Device Information” dialog box.
Chapter 7. Dialog boxes/Software applications “External Events” dialog box ❑ “External Events” dialog box Here you can make settings for a command that will be transmitted to the network to which the Dante connector or NETWORK connector is connected. This command can be triggered by recalling a preset on the MTX/MRX; or by input from GIP IN; or by operation of an external device such as a DCP unit. NOTE Only commands are transmitted, and any reply to the commands will be discarded.
Chapter 7. Dialog boxes/Software applications “External Events” dialog box ● [Event Mode] list box Specify whether the triggered command is the [On/Off] or [1shot] type. When an event is assigned to the button on an external device, such as a DCP unit, each command type will cause the following operation: • [On/Off] Pressing the assigned button repeatedly will cause the MTX/MRX to transmit the On command and Off command alternately.
Chapter 7. Dialog boxes/Software applications “External Events” dialog box ● Command text box If [On/Off] has been selected in the [Event Mode] list box, repeatedly pressing the button on an external device, such as a DCP unit, will cause the MTX/MRX to transmit the On command and Off command alternately. If [1shot] has been selected in the [Event Mode] list box, repeatedly pressing the button on an external device, such as a DCP unit, will cause the MTX/MRX to transmit the programmed commands.
Chapter 7. Dialog boxes/Software applications “Digital Control Panel” dialog box ❑ “Digital Control Panel” dialog box Here you can assign the MTX/MRX’s parameters to the controls of a digital control panel (DCP) such as the DCP1V4S so that they can be operated from the DCP. You can also make settings for the brightness of the DCP unit’s LEDs, as well as panel lock settings. You can’t make settings while online. (Settings can only be viewed.) You can store 32 sets of DCP settings in the Library.
Chapter 7. Dialog boxes/Software applications “Digital Control Panel” dialog box ● [Save] button This button stores an item in the library. The “Save Library” dialog box will appear. If you edit the parameters of the loaded library item, the text will turn red. The text will turn black when you save or load the library item. • [Name:] Enter a name for the library item. You can’t enter the name of an existing library item, nor can you enter a blank name.
Chapter 7. Dialog boxes/Software applications “Digital Control Panel” dialog box ● [Parameter Assign] tab Here you can assign the MTX/MRX’s parameters to the various controls. The currently-selected control is highlighted. The corresponding control is also highlighted in the graphic that’s shown at the left of the tab. ❍ Control select buttons When you click a button, the “Settings” dialog box will appear, letting you make settings for the controls.
Chapter 7. Dialog boxes/Software applications “Digital Control Panel” dialog box • [LED Brightness] box Specifies the brightness of the DCP unit’s LEDs. Higher values will make the LEDs brighter. • [Enable Inactive Mode] check box If the check box is selected, the unit automatically enters inactive mode after a time duration specified in [Waiting Time]. [Inactive LED Brightness] specifies the brightness of the LEDs when inactive.
Chapter 7. Dialog boxes/Software applications “Digital Control Panel” dialog box “Settings” dialog box You can access this dialog box from the “Digital Control Panel” dialog box, the “Wireless DCP” dialog box, or the “GPI” dialog box. NOTE For details on the “Settings” dialog box that is accessed from the “Preset” dialog box and the “Scheduler” dialog box, refer to “Settings” dialog box in chapter 6. ● [FUNCTION] list Selects the function to be controlled.
Chapter 7. Dialog boxes/Software applications “Wireless DCP” dialog box ❑ “Wireless DCP” dialog box Here you can assign the parameters of the MTX/MRX to controls of the “Wireless DCP” iOS app so that they can be operated from Wireless DCP. You can’t make settings while online. (Settings can only be viewed.) For details on Wireless DCP, refer to the “Wireless DCP User’s Manual.” You can store 32 sets of Wireless DCP settings in the Library. You can also associate library items with presets for recall.
Chapter 7. Dialog boxes/Software applications “Wireless DCP” dialog box ● Menu button ( ) Click this button to execute the following functions. • [Clear Page] Initializes the displayed page. • [Clear All Pages] Initializes the Wireless DCP settings of the selected MTX/MRX. ● [PAGE NAME] Assign a name to the page. The name in the Wireless DCP “Page select” screen is shown. ● [Template] button Click this to open the “Template” dialog box. Select the controls that will be shown in “Wireless DCP.
Chapter 7. Dialog boxes/Software applications “MCP1” dialog box ❑ “MCP1” dialog box Up to 16 MCP1 units can be connected to one MTX/MRX system. Using Ethernet cables, connect the MTX/MRX unit’s [NETWORK] port or Dante port to a PoE network switch, and connect the PoE network switch to the MCP1. If the network switch does not support PoE, connect a PoE injector between the network switch and the MCP1.
Chapter 7. Dialog boxes/Software applications “MCP1” dialog box ● [Save] button This button saves an item in the library. The “Save Library” dialog box will appear. If you edit the parameters of the loaded library item, the text will turn red. The text will turn black when you save or load the library item. • [Name:] Enter a name for the library item. You can’t enter the name of an existing library item, nor can you enter a blank name. • [OK] button Saves the library item and closes the dialog box.
Chapter 7. Dialog boxes/Software applications “MCP1” dialog box ● [Home]/[Page 1]–[Page 6] tabs Here you can make settings related to the MCP1 page. The home page is the page that appears at start-up, or when you touch the MCP1’s home switch. In the home page, you can switch pages by assigning [Open Page] to a switch. Here we explain using the [Page 1] tab. The currently-selected switch is highlighted.
Chapter 7. Dialog boxes/Software applications “MCP1” dialog box ● [Dimmer & Lock] tab Here you can make settings for the brightness of the MCP1’s display and switches, and for panel lock. • [Brightness] check box If this check box is selected, the brightness and contrast of the display, and the brightness of the switches, can be changed when a preset recalls the currently-edited library item. [LCD Brightness] specifies the brightness of the display. Higher values will make the display brighter.
Chapter 7. Dialog boxes/Software applications “MCP1” dialog box ● Menu button ( ) Click this button to execute the following functions. • [Copy] Copies the Home, Page 1–Page 6, Dimmer & Lock, and Source Select settings of the displayed MCP1 to the copy buffer. • [Paste] Overwrites the Home, Page 1–Page 6, Dimmer & Lock, and Source Select settings from the copy buffer onto the displayed MCP1. It is only possible to paste settings that were copied within the same MTX/MRX system.
Chapter 7. Dialog boxes/Software applications “PIN Setup” dialog box ❑ “PIN Setup” dialog box Here you can specify PIN codes for all MCP1 units within the MTX/MRX system. A PIN code is specified if the system goes online with the MCP1 even once. If this has not been specified, use 1111 to unlock. ● [MCP1 Admin PIN:] text box This is the PIN code for opening the MCP1’s Settings page. It can also be used as the “Power User PIN” or the “Panel Unlock PIN.
Chapter 7. Dialog boxes/Software applications “Label” dialog box ❑ “Label” dialog box Here you can create a page image to show in the MCP1’s display. ● [Cell] Edit the page image. To edit the text string, select a cell and double-click or press the key. To confirm, press the key or use the mouse to select another cell. To insert an image, select the cell, then select the [Image Settings] check box and press the [Import] button and select an image file.
Chapter 7. Dialog boxes/Software applications “Label” dialog box • Font size list box Selects the font size for the text string. • [B]/[I]/[U] buttons Click these buttons to apply bold, italic, or underlined character styles to the text string in the cell. • “Color” Indicates the color of the text string in the cell. Click this button to switch between white and black. • [Alignment] list box Selects the position at which the text string is displayed in the cell.
Chapter 7. Dialog boxes/Software applications “Re-size Image” dialog box ❑ “Re-size Image” dialog box Here you can select how the image is placed. ● Option buttons From above, the following choices are provided. • Keep Original • Image is scaled to maximum possible size. Aspect ratio is ignore. • Image is scaled to maximum possible size, preserving original aspect ratio and full image. • Image is scaled to maximum possible, preserving original aspect ratio.
Chapter 7. Dialog boxes/Software applications “PGM1/PGX1” dialog box ❑ “PGM1/PGX1” dialog box Here you can make assignments for the zone/message select buttons of the PGM1 and PGX1, and make settings for the PTT button. This dialog box can shown only for the MTX5-D or MRX7-D. If using the PGM1 with the MRX7-D, use MRX Designer to place the “Paging” component. ● MTX/MRX select list box Selects the MTX/MRX to which the PGM1 unit for which you want to make settings is connected.
Chapter 7. Dialog boxes/Software applications “PGM1/PGX1” dialog box ● [Function Assign] tab Here you can assign functions to the zone/message select buttons of the PGM1 or PGX1. “FUNCTION” provides the following choices. • [No Assign] No function is assigned to the button. • [Zone] Selects/de-selects the zone to broadcast. When selected, the zone/message indicator is lit. • [Zone Group] Selects/de-selects multiple zones to broadcast in a single operation.
Chapter 7. Dialog boxes/Software applications “PGM1/PGX1” dialog box • [All Zone On/Off] Selects/de-selects all zones/zone groups. This does not affect the selection status for the zones/zone groups of other PGM1/ PGX1 units. The zone/message indicator is lit when broadcast is possible to all zones/zone groups. • Menu button ( ) Click the menu button to execute the following functions. - [Copy] Copies the FUNCTION and PARAMETER settings of the corresponding device to the copy buffer.
Chapter 7. Dialog boxes/Software applications “PGM1/PGX1” dialog box ● [Properties] tab Here you can make settings for the operation of the PCM1. • [Stop all broadcast.] option button If this is selected, paging broadcast including the scheduler will be stopped when the MTX/MRX system is in emergency mode. • [Stop broadcast except for 1st Priority PGM1] option button If this is selected, paging broadcast will be possible only for the 1st Priority PGM1 when the MTX/MRX system is in emergency mode.
Chapter 7. Dialog boxes/Software applications “PGM1 Label Creator” application ❑ “PGM1 Label Creator” application Here you can create a printable label image for the PGM1 or PGX1. To print the label, connect a printer to the computer. ● Pattern select buttons Select the label pattern. PGM1 Label Creator can store up to three patterns on one computer. ● [Export] button Saves the settings to a file. Click this to open the “Save File” dialog box. The file extension is *.plc.
Chapter 7. Dialog boxes/Software applications “PGM1 Label Creator” application To move between cells, you can use not only mouse operations but also the cursor keys, key, or key. By holding down the key while moving between cells, you can select a region. ● “Font Settings” area Here you can specify the font for the selected cell. The “Preview” area shows how the settings will appear. • Font list box Selects a font for the text string.
Chapter 7. Dialog boxes/Software applications “PGM1 Label Creator” application ● [All Clear] button Initializes all cell settings for the selected pattern. ● [OK] button Saves the settings and closes the application. Since the settings are not saved in the MTX-MRX Editor project file, you should click the [Export] button and save the file if you want to reuse the settings. ● [Cancel] button Discards the settings and closes the application.
Chapter 7. Dialog boxes/Software applications “GPI” dialog box ❑ “GPI” dialog box GPI stands for General Purpose Interface. By using the GPI input/output, you can remotely control the MTX/MRX via custom-made controllers or external devices. A controller that is connected to the GPI input connector can be used to switch presets on the MTX/MRX or to control the parameters of components. GPI input/output settings are made individually for each device.
Chapter 7. Dialog boxes/Software applications “GPI” dialog box ● [GPI on] box From the list, choose the MTX/MRX unit whose settings you want to specify. The list shows the UNIT ID and device name of the MTX/MRX units that are assigned to the MTX/MRX system. ● [Clear] button Initializes the settings of all ports. ● PORT select buttons These buttons open the “Settings” dialog box where you can make settings for each port. For details on these parameters, refer to List of settings in “Settings” dialog boxes.
Chapter 7. Dialog boxes/Software applications “GPI Calibration” dialog box ❑ “GPI Calibration” dialog box Here you can calibrate the input voltage detection range for the [GPI] connector of the MTX/MRX unit. (Available only when online.) These settings adjust the detection range in order to stabilize the input voltage of the [GPI] connector. ● [Device:] box Selects an MTX/MRX unit within the MTX/MRX system.
Chapter 7. Dialog boxes/Software applications “GPI Calibration” dialog box Calibration procedure 1. Connect your external device to the MTX/MRX’s [GPI] connector. 2. Select the check box of the channel numbers for which you want to perform calibration. If you want to select all channels, select the [All Ports] check box. 3.
Chapter 7. Dialog boxes/Software applications “Security Settings” dialog box ❑ “Security Settings” dialog box On the MTX/MRX system, you can specify a PIN code (numeric password) for security. ● [Security] check box If this check box is selected, the “Security” dialog box will appear when the project file starts. If this check box is cleared, all users will be able to make changes in MTX-MRX Editor. ● [PIN Code] If the [Security] check box is selected, enter the PIN code (four single-byte numerals).
Chapter 7. Dialog boxes/Software applications “Project Information” dialog box ❑ “Project Information” dialog box Allows you to include a memo in the project file to record property information or contact information.
Chapter 7. Dialog boxes/Software applications “Configuration Diagram” dialog box ❑ “Configuration Diagram” dialog box Displays a diagram that shows how devices such as the MTX/MRX, XMV, and DCP are connected. The configuration diagram can be printed. ● [>>Page 2]/[>>Page 1] buttons Switch between configuration diagram screens. ● [Print] button Starts printing the configuration diagram. ● [Close] button Closes the dialog box without printing the configuration diagram.
Chapter 7. Dialog boxes/Software applications “Get Log” dialog box ❑ “Get Log” dialog box A record of the MTX/MRX system’s operation is stored as a “log” in the MTX/MRX’s internal memory. In this dialog box you can output the logs of all MTX/MRX units existing on the subnet to which your computer is connected, and save them as a file. The log file is in “.csv” format. NOTE • The Project screen’s [Alert] tab does not show the information listed in the alert list, but this is captured in the log.
Chapter 7. Dialog boxes/Software applications “Sampling Rate Converter” dialog box ❑ “Sampling Rate Converter” dialog box Here you can turn on/off the SRC (Sampling Rate Converter) of the MY4-AEC or MY8-AE96S that is installed in the device’s slot, and specify the word clock setting of the output. ● [ON] button Switches the SRC on/off. The button also shows the on/off status. ● [Fs Type] box (MY4-AEC only) This selects the word clock that will be output from the MY4-AEC when SRC is on.
Chapter 7. Dialog boxes/Software applications “Input Source/Redundant” dialog box ❑ “Input Source/Redundant” dialog box Here you can specify for each channel whether the input source to the XMV will be digital or analog. If the input source is specified as digital, you can specify that the input source will switch from digital to analog when a pilot tone or analog input is detected. Here we explain the screen for when the digital input is YDIF. ● [Redundant Mode] list box Selects the redundancy method.
Chapter 7. Dialog boxes/Software applications “Input Source/Redundant” dialog box ● [Auto Return] check box If this check box is selected, operation will be as follows. • In the case of Backup mode When the digital input returns, the input source is switched to digital. • In the case of Override mode When the analog input falls below the threshold value, the input source is returned from analog to digital. ● Channel list box Selects the input channel for which to make settings.
Chapter 7. Dialog boxes/Software applications “Input Source/Redundant” dialog box ● “Redundant Mode - Override” area Here you can specify the conditions under which each channel will switch to the analog input in Override mode. • [Override Threshold] spin box Specifies the threshold value for the analog input. When the threshold value is exceeded, the input source will switch to analog.
Appendix List of settings in “Settings” dialog boxes This section explains the settings in the following “Settings” dialog boxes. For details about settings that are unique to the MRX series, refer to “MRX Designer User Guide.” • DCP/Wireless DCP/MCP1 • GPI Input • GPI Output ■ DCP/Wireless DCP/MCP1 Settings for the switches and knobs/sliders of the DCP, the Wireless DCP, or MCP1 are explained here.
List of settings in “Settings” dialog boxes Appendix ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1] Specify the channel that will control the on/off setting of the parameter. ● If [FUNCTION] is [MTX Send ON] (switch only) The switch turns the send on/off. Select one of the following parameter types, and then make the appropriate setting. • Input Ch Send ON • Fx RTN Send ON ❍ [DEVICE] Select the device that you want to change.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [SD Play] (switch only) Play/stop the audio file that is specified by the switch. Select one of the following parameter types, and then make the appropriate setting. • SD Song Select & Play • SD Song Pause ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name.
List of settings in “Settings” dialog boxes Appendix If [Play all songs in a folder] is selected Select the folder shown in [SD CARD:/]. Up to 100 songs saved in the currently selected folder will play. The following folder formats can be shown. • (folder name) • blank NOTE - Only first-level folders are valid. - If the folder name is blank, the songs that exist in the root level of the memory card will be played (folders below the root level will not be included).
List of settings in “Settings” dialog boxes Appendix ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1]/[PARAMETER2] Specify the channel whose level will be controlled. ❍ [Parameter Range] Use [Upper Limit] and [Lower Limit] to specify the range in which the level can be varied. If [Mute Enable] is on, the mute state (–∞ dB) will be enabled if the level is lowered below the value specified by [Lower Limit].
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX Level Inc/Dec] or [MTX Send Level Inc/Dec] (DCP switches only) Use the switch to change the level or send level. Select one of the following parameter types, and then make the appropriate setting.
List of settings in “Settings” dialog boxes Appendix ❍ [Dec] If you select this option, pressing the switch repeatedly will lower the level or the send level. ✦[Lower Limit] Specifies the minimum level to be achieved when you press the switch. ✦[Mute Enable] check box If this option is selected, the Mute state (–∞ dB) will be enabled if the level is lowered below the value specified by [Lower Limit]. ❍ [Switch] Allows you to make switch-related settings.
List of settings in “Settings” dialog boxes Appendix Using a knob/slider to adjust the send level (other than DCP4S–EU/US) Shown below is an example of using a switch to turn send on/off and using a knob/ slider to adjust the send level. The switch settings and knob/slider settings for this example are explained below.
List of settings in “Settings” dialog boxes Appendix Switch settings Select the following parameter type to be controlled by the switch, and then make the appropriate settings. • Input Ch Send On ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1]/[PARAMETER2] In the [PARAMETER1] column, select the target ZONE. In the [PARAMETER2] column, click ? on the left of the channel name to select ON, OFF, or IGNORE for the desired channels.
List of settings in “Settings” dialog boxes Appendix Using switches to adjust the send level Shown below is an example of using switches to turn send on/off and to adjust the send level. The switch settings for this example are explained below.
List of settings in “Settings” dialog boxes Appendix Switch settings Select the following parameter types to be controlled by the switches, and then make the appropriate settings. • Input Ch Send On • Input Ch Send Level ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1]/[PARAMETER2] In the [PARAMETER1] column, select the target ZONE.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX Source Select] (MCP1) The switch that is assigned to [Input Ch Send ON] will select the send point of the Matrix, and the switch/knob/slider that is assigned to [Input Ch Send Level] will adjust the level of the send point. We will explain the switch settings in this example.
List of settings in “Settings” dialog boxes Appendix Select the following parameter types to be operated by the switches, and then make various settings. • Input Ch Send On • Input Ch Send Level ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1]/[PARAMETER2] In the [PARAMETER1] column, select the target ZONE.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [Legacy - MTX Source Select w/knob] (only for switches of a DCP equipped with knobs) You can control the send on/off for multiple channels via switches, and control the send level for any channel via knobs. NOTE If you assign the same source to multiple DCP units and then change the settings on one of the DCP units, the changes will not be updated on other DCP units.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [Legacy - MTX Source Select w/sw] (DCP switches only) You can control the send on/off for multiple channels via switches, and the send level for any channel via switches. NOTE If you assign the same source to multiple DCP units and then change the settings on one of the DCP units, the changes will not be updated on other DCP units. Each DCP unit will retain the settings (LED status and knob assignments) that were made on it.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [External Event] (switch only) A switch will be used to output commands specified in the “Event” dialog box. ❍ [DEVICE] Select a device to output commands. These are shown in order of UNIT ID and model name. ❍ [PARAMETER1] Select an event to be executed. ❍ [Indicator] Select whether the switch indicator will display the on/off status (Latch), or light only when the switch is pressed (Unlatch).
List of settings in “Settings” dialog boxes Appendix ■ GPI Input This section explains settings for the [GPI IN] connector of the device itself. Connection examples using the [GPI IN] connector Connection example 1: Controlling the MTX/MRX with a switch MTX3 +5VDC +V CPU IN A/D 100k Connection example 2: Controlling the MTX/MRX with a 10kΩ B-curve variable resistor MTX3 +5VDC +V CPU IN A/D GND 100k About [INPUT TYPE] [INPUT TYPE] allows the following settings. • Analog • Analog Inv.
List of settings in “Settings” dialog boxes Appendix NOTE • The threshold value at which on/off switching will occur will be the middle value between the maximum and minimum input voltage values (the value equal to the sum of the maximum and minimum values divided by two). To prevent malfunctions, you should allow plenty of room for detection (see “GPI Calibration” dialog box).
List of settings in “Settings” dialog boxes ❍ Appendix Low Active Use this if you selected [ON] or [Send ON] as the [FUNCTION]. The function will turn off when the input voltage to GPI IN rises above the center voltage, and will turn on when it falls below the center voltage. GPI IN input voltage max. OFF OFF GPI IN input voltage min. Center voltage ON NOTE If you’ve selected [Input Ch Mute Group] or [Zone Out Mute Group] as the parameter type, mute on/off will be switched.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX Dugan Automixer] The input voltage to the [GPI IN] connector will turn the parameter on/off. Select one of the following parameter types, and then make the appropriate setting. • Override (master) • Mute (master) • override (Ch) ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER 1] For Override (master) and Mute (master), select the group that controls on/off.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX ON] Controls the on/off setting of the parameter. Select one of the following parameter types, and then make the appropriate setting. • Input Ch ON • Fx RTN ON • ZONE Out ON • Output Ch ON • Input Ch Mute Group • ZONE Out Mute Group ❍ [DEVICE] Select the device that you want to change. ❍ [PARAMETER1] Specify the channel that will control the on/off setting of the parameter.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [SD Play] The input voltage to the [GPI IN] connector will play the specified audio file. Select one of the following parameter types, and then make the appropriate setting. • SD Song Select & Play • SD Song Pause For details on settings other than [INPUT TYPE], refer to If [FUNCTION] is [SD Play] (switch only) for switches. ❍ [INPUT TYPE] Specifies how the input voltage to GPI IN will be applied to the parameter.
List of settings in “Settings” dialog boxes Appendix ■ GPI Output This section explains settings for the [GPI OUT] connector of the device itself. To make [GPI OUTPUT] connector settings by recalling a preset, start with “Preset” dialog box.
List of settings in “Settings” dialog boxes Appendix About [OUTPUT TYPE] [OUTPUT TYPE] allows the following settings. • Closed • Open • Pulse • Pulse Inv. ❍ Closed When the selected [FUNCTION] state occurs, the contact will be closed. In the case of a parameter for which [Threshold] is specified, the contact will be closed when the threshold value is exceeded. ❍ Open When the selected [FUNCTION] state occurs, the contact will be opened.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX Dugan Automixer] Parameter on/off operations will control the GPI Output. Select one of the following parameter types, and then make the appropriate setting. • Override (master) • Mute (master) • override (Ch) ❍ [DEVICE] Select the device that you want to change. These are shown in order of UNIT ID and model name. ❍ [PARAMETER 1] For Override (master) and Mute (master), select the group that controls on/off.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [MTX ON] Parameter on/off operations on the specified device will control the GPI Output. Select one of the following parameter types, and then make the appropriate setting. • Input Ch ON • Fx RTN ON • ZONE Out ON • Output Ch ON • Input Ch Mute Group • ZONE Out Mute Group ❍ [DEVICE] Select the device that you want to change. ❍ [PARAMETER1] Specifies the channel whose on/off operations will control the [GPI OUT} connector.
List of settings in “Settings” dialog boxes Appendix ●If [FUNCTION] is [SD Song Play] The status of audio file playback will be output to the [GPI OUT] connector. ❍ [DEVICE] Select the device that you want to change. ❍ [OUTPUT TYPE] Specifies how output will occur from the [GPI OUT] connector. ● If [FUNCTION] is [Alert] A signal will be output to the [GPI OUT] connector when an alert occurs. ❍ [DEVICE] Selects the device whose [GPI OUT] connector will output the alert.
Workflow for paging settings Appendix Workflow for paging settings The workflow for making paging settings is as follows. For specific settings, refer to “MTX Setup Manual.” Notice Input channels to which audio signals from a PGM1 are assigned should not be mixed in the “MATRIX” screen. If these signals are mixed, the input from the PGM1 units will be output to the zone even if PTT is off. 1. In the “Device Config Wizard” dialog box, configure the PGM1. 2.
Workflow for paging settings Appendix 4. In the input channel port selection screen of the “MAIN” screen, assign the input from the PGM1 to an input channel. Notice Input channels to which audio signals from a PGM1 are assigned should not be mixed in the “MATRIX” screen. If these signals are mixed, the input from the PGM1 units will be output to the zone even if PTT is off. 5. In the “PAGING” screen of the “ZONE” screen, assign the input from the 1st Priority Mic specified in step 2 to 1st MIC.
Workflow for paging settings Appendix 7. In the “PAGING” screen of the “ZONE” screen, click the [Settings] button, and in the [Function Assign] tab, assign functions to the zone/ message select buttons of the PGM1/PGX1. 8. In the [Properties] tab, make settings for the opening chime, etc.
Settings for controlling devices across subnets Appendix Settings for controlling devices across subnets If you are controlling devices on a subnet that is different than that of MTX-MRX Editor, all devices are distinguished by their IP address. For this reason, it is necessary to make settings so that the IP settings of devices placed in MTXMRX Editor (these are called virtual devices) match the IP settings of devices on the network (these are called real devices).
Settings for controlling devices across subnets Appendix “Range” shows the IP address setting range. 4 -4. Click the [Apply IP Address] button. IP addresses are automatically assigned to the virtual devices in the system. 5. Click the [Apply] button. 6. Repeat steps 3 through 5 to assign IP addresses to all virtual devices. 7. When you have finished making settings, click the [OK] button. Next, use the “IP Address” dialog box to specify IP addresses for the real devices.
Settings for controlling devices across subnets Appendix 5. Click the [Auto-Assign IP Addresses] button so that the virtual device IP settings specified in the “Match Device by IP Address” dialog box are applied to the “IP Address” dialog box. The “Auto-Assign IP Addresses” dialog box opens. The IP settings of the virtual devices are shown. 6. If you need to connect to a DNS server, specify the [DNS Server] setting. 7.
Alert list Appendix Alert list The alerts generated by the MTX/MRX and the XMV, and their significance and the appropriate actions, are listed below. The number is shown as two digits on the MTX/MRX unit, and as three digits on the XMV unit. A single alert is shown when the event occurs. A continuing alert is shown when the event occurs and when it ends. Some alerts and information are shown in MTX-MRX Editor but not shown on the unit itself.
Alert list Appendix Number Content 21 The word clock master has become unlocked. 22 The digital signal being input to the [YDIF IN] connector is not synchronized to the word clock of this device. 23 The digital signal being input to the [YDIF IN] connector is not continuously synchronized to the word clock of this device. 24 The digital signal being input to the slot is not synchronized to the word clock of this device.
Alert list Appendix Number Content Action Type Single/ Continuing 47 Event [**] could not be transmitted. Check the devices that are connected to the network. 50 The UNIT ID is set to “00.” Set the UNIT ID to something other than “00.” Error Continuing 51 Devices with identical UNIT IDs were found connected within the same network. Change the UNIT ID so that there are no duplicates. Error Continuing 52 A communication error occurred with the [DCP] connection.
Alert list Appendix Number Content Action Type Single/ Continuing 67 Invalid parameters set for DCP[*]. Check the DCP[*] settings and perform synchronization again. Error Continuing 70 Synchronization has not been completed. It may be that synchronization was halted before completion. Perform synchronization again using MTXMRX Editor. If this does not solve the problem, initialize the memory of the device and synchronize again. If this also fails, contact your Yamaha dealer.
Alert list Appendix Number Action 202 The firmware update has been completed. – Information Single 203 Initialization has been executed. – Information Single 204 Panel lock has been disabled. – Information Single 205 The IP address has been established. – Information Single 206 The network IP address has been allocated from the DHCP server. – Information Single 207 The network IP address has been released by the DHCP server.
Alert list Appendix Number Type Single/ Continuing Content Action 102 Protection has been activated, and the limiter[ch*] is in operation. Continuous high-power output may have activated protection; lower the output level. For details on the reason that protection was activated, refer to the owner’s manual. Information Continuing 110 The Redundant Backup function has operated, and channel * has switched to analog input. There is a problem with the digital signal.
Troubleshooting Appendix Troubleshooting Problem Possible cause Action The IP address setting of the computer is incorrect. Refer to “MTX Setup Manual” or “MRX Setup Manual,” and specify the IP address of the computer. Right-click [Start]¦[Control Panel]¦[System and Security]¦[Allow an App through Windows Firewall]; then click the [Change settings] button, and select the check boxes for “Bonjour service” and “MTX-MRX Editor.
Troubleshooting Problem Appendix Possible cause Action Check whether the cables between each device are connected correctly. If the cables are connected correctly, A cable is broken or disconnected. check whether they might be broken, and replace any that are broken. No sound is output. The DIP switches on the unit are set incorrectly. Check the setting of the DIP switches on the unit. In particular if START UP MODE is set to INIT.