OWNER’S MANUAL YZFR1X(C) LIT-11626-21-41 4C8-28199-11
U4C811E0.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha YZFR1X(C). This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM IMPORTANT MANUAL INFORMATION EAU10131 Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! WARNING Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM IMPORTANT MANUAL INFORMATION AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE. *Product and specifications are subject to change without notice.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM IMPORTANT MANUAL INFORMATION EAU10192 AFFIX DEALER LABEL HERE YZFR1X(C) OWNER’S MANUAL ©2007 by Yamaha Motor Corporation, U.S.A. 1st edition, June 2007 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in Japan.
U4C811E0.book Page 1 Thursday, June 7, 2007 3:08 PM TABLE OF CONTENTS SAFETY INFORMATION ..................1-1 Location of important labels ...........1-5 PRE-OPERATION CHECKS ............. 4-1 Pre-operation check list ................. 4-2 DESCRIPTION ..................................2-1 Left view ..........................................2-1 Right view ........................................2-2 Controls and instruments ................2-3 OPERATION AND IMPORTANT RIDING POINTS .......................
U4C811E0.book Page 2 Thursday, June 7, 2007 3:08 PM TABLE OF CONTENTS Replacing a headlight bulb ...........6-38 Tail/brake light ..............................6-40 Replacing a turn signal light bulb ...........................................6-41 Replacing the license plate light bulb ...........................................6-41 Replacing an auxiliary light bulb ...6-42 Supporting the motorcycle ............6-43 Front wheel ...................................6-43 Rear wheel ............................
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION EAU10281 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE. HE OR SHE SHOULD: ● OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF MOTORCYCLE OPERATION.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION 1 ● ● due to EXCESSIVE SPEED or undercornering (insufficient lean angle for the speed). • Always obey the speed limit and never travel faster than warranted by road and traffic conditions. • Always signal before turning or changing lanes. Make sure that other motorists can see you. The posture of the operator and passenger is important for proper control.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION Loading The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit. Maximum load: 195 kg (430 lb) When loading within this weight limit, keep the following in mind: ● Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability.
U4C811E0.book Page 4 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION 1 ● tor and may limit control ability, therefore, such accessories are not recommended. Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power. Gasoline and exhaust gas ● GASOLINE IS HIGHLY FLAMMABLE: • Always turn the engine off when refueling.
U4C811E0.book Page 5 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION EAU10381 Location of important labels Please read the following important labels carefully before operating this vehicle.
U4C811E0.book Page 6 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION 1 CAUTION 3 California only 4 California only Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield. Use neutral detergent. 1 5JW-00 California only 2 HOW TO LAYOUT FUEL HOSES #1 #2 #3 #4 FUEL TANK FUEL PUMP FUEL FILTER FUEL DELIVERY PRESS.
U4C811E0.book Page 7 Thursday, June 7, 2007 2:38 PM SAFETY INFORMATION 5 8 WARNING BEFORE YOU OPERATE THIS VEHICLE, READ THE OWNER’S MANUAL AND ALL LABELS. ALWAYS WEAR AN APPROVED MOTORCYCLE HELMET, eye protection, and protectibe clothing. 1 290 kPa, {2.90 kgf/cm 2 }, 42psi PREMIUM UNLEADED GASOLINE ONLY 91 Min.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM DESCRIPTION EAU10410 Left view 2 8. Shock absorber assembly rebound damping force adjusting screw (page 3-19) 9. Shock absorber assembly spring preload adjusting ring (page 3-19) 10.Engine oil drain bolt (page 6-13) 11.Coolant drain bolt (page 6-17) 12.Engine oil filter cartridge (page 6-13) 13.Front fork compression damping force adjusting screw (page 3-17) 1. 2. 3. 4. 5. 6.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM DESCRIPTION EAU10420 Right view 2 1. 2. 3. 4. 5. 6. 7. 8. 9. Engine oil level check window (page 6-13) 10.Engine oil filler cap (page 6-13) 11.Rear brake light switch (page 6-26) 12.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM DESCRIPTION EAU10430 Controls and instruments 2 1. 2. 3. 4. 5. 6. 7. 8.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU10460 NOTE: The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls. Main switch/steering lock To lock the steering EAU10660 OFF All electrical systems are off. The key can be removed. The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS To unlock the steering EAU11003 Indicator and warning lights EAU11060 Neutral indicator light “ ” This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light “ ” This indicator light comes on when the high beam of the headlight is switched on. 3 EAU11250 1. Push. 2. Turn. Push the key in, and then turn it to “OFF” while still pushing it.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle.
U4C811E0.book Page 4 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS Coolant temperature Display Conditions What to do Under 39 °C (Under 103 °F) Message “Lo” is displayed. OK. Go ahead with riding. 40–116 °C (104–242 °F) Temperature is displayed. OK. Go ahead with riding. 117–139 °C (243–283 °F) Temperature display flashes. Warning light comes on. Stop the vehicle and allow it to idle until the coolant temperature goes down. If the temperature does not go down, stop the engine.
U4C811E0.book Page 5 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU11530 Engine trouble warning light “ ” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the selfdiagnosis system. (See page 3-5 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”.
U4C811E0.
U4C811E0.book Page 7 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. Odometer, tripmeter, and stopwatch modes 1.
U4C811E0.book Page 8 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS Air intake temperature display Coolant temperature display ● When the air intake temperature display is selected, “A” is displayed before the temperature. Self-diagnosis devices 3 1. Coolant temperature display 1. Air intake temperature display The coolant temperature display indicates the temperature of the coolant.
U4C811E0.book Page 9 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS ECA11590 CAUTION: If the display indicates an error code, the vehicle should be checked as soon as possible in order to avoid engine damage. ● ● Display brightness and shift timing indicator light control mode ● ● 1. Display brightness 2. Shift timing indicator light activation/deactivation 3. Shift timing indicator light 4.
U4C811E0.book Page 10 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS ● 3 The indicator light will stay on when activated. (This setting is selected when the indicator light stays on.) ● The indicator light will flash when activated. (This setting is selected when the indicator light flashes four times per second.) ● The indicator light is deactivated; in other words, it will not come on or flash. (This setting is selected when the indicator light flashes once every two seconds.) 2.
U4C811E0.book Page 11 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12347 Handlebar switches Left EAU12400 Dimmer switch “ / ” Set this switch to “ ” for the high beam and to “ ” for the low beam. ECA10050 CAUTION: See page 5-1 for starting instructions prior to starting the engine. EAU12460 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the center position.
U4C811E0.book Page 12 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU12820 EAU12870 EAU33850 Clutch lever Shift pedal Brake lever 1. Clutch lever 1. Shift pedal The clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handlebar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch operation.
U4C811E0.book Page 13 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS it by aligning a groove on the adjusting knob with the “ ” mark on the brake lever. EAU12941 Brake pedal EAU13072 Fuel tank cap 3 1. Brake pedal The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal. 1. Fuel tank cap lock cover 2. Unlock.
U4C811E0.book Page 14 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU13220 NOTE: The fuel tank cap cannot be closed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked. Fuel ECA10070 CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts. EWA11090 WARNING 3 EAU13380 Make sure that the fuel tank cap is properly closed before riding. 1.
U4C811E0.book Page 15 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS octane number of 95 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. Gasohol There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10%.
U4C811E0.book Page 16 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS 2. Lift the front of the passenger seat and pull it forward. EAU33870 Helmet holders To install the passenger seat 1. Insert the projection on the rear of the passenger seat into the seat holder as shown, and then push the front of the seat down to lock it in place. 3 1. Projection 2. Seat holder 1. Helmet holder Passenger seat The helmet holders are located on the bottom of the passenger seat.
U4C811E0.book Page 17 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS To release a helmet from a helmet holder Remove the passenger seat, remove the helmet from the helmet holder, and then install the seat. EAU14741 Adjusting the front fork This front fork is equipped with spring preload adjusting bolts, rebound damping force adjusting screws and compression damping force adjusting screws.
U4C811E0.book Page 18 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS Rebound damping force Compression damping force ECA10100 CAUTION: Never attempt to turn an adjusting mechanism beyond the maximum or minimum settings. 3 1. Rebound damping force adjusting screw 1. Compression damping force adjusting screw To increase the rebound damping force and thereby harden the rebound damping, turn the adjusting screw on each fork leg in direction (a).
U4C811E0.book Page 19 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU42940 Adjusting the shock absorber assembly This shock absorber assembly is equipped with a spring preload adjusting ring, a rebound damping force adjusting screw, a compression damping force adjusting bolt (for fast compression damping) and a compression damping force adjusting bolt (for slow compression damping). ECA10100 CAUTION: Never attempt to turn an adjusting mechanism beyond the maximum or minimum settings.
U4C811E0.book Page 20 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS 3 Rebound damping setting: Minimum (soft): 20 click(s) in direction (b)* Standard: 12 click(s) in direction (b)* Maximum (hard): 3 click(s) in direction (b)* * With the adjusting screw fully turned in direction (a) Compression damping force 1. Compression damping force adjusting bolt (for fast compression damping) 2. Compression damping force adjusting bolt (for slow compression damping) direction (a).
U4C811E0.book Page 21 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS the following information before handling the shock absorber. The manufacturer cannot be held responsible for property damage or personal injury that may result from improper handling. ● Do not tamper with or attempt to open the gas cylinder. ● Do not subject the shock absorber to an open flame or other high heat sources, otherwise it may explode due to excessive gas pressure.
U4C811E0.book Page 22 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS EAU15301 Sidestand The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright. 3 below and have a Yamaha dealer repair it if it does not function properly. NOTE: The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations.
U4C811E0.book Page 23 Thursday, June 7, 2007 2:38 PM INSTRUMENT AND CONTROL FUNCTIONS With the engine turned off: 1. Move the sidestand down. 2. Make sure that the engine stop switch is turned on. 3. Turn the key on. 4. Shift the transmission into the neutral position. 5. Push the start switch. Does the engine start? YES NOTE: This check is most reliable if performed with a warmed-up engine. NO The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM PRE-OPERATION CHECKS EAU15593 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM PRE-OPERATION CHECKS EAU15605 Pre-operation check list ITEM CHECKS PAGE Fuel • Check fuel level in fuel tank. • Refuel if necessary. • Check fuel line for leakage. 3-14 Engine oil • Check oil level in engine. • If necessary, add recommended oil to specified level. • Check vehicle for oil leakage. 6-13 Coolant • Check coolant level in reservoir. • If necessary, add recommended coolant to specified level. • Check cooling system for leakage.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM PRE-OPERATION CHECKS ITEM CHECKS PAGE Throttle grip • Make sure that operation is smooth. • Check cable free play. • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. 6-21, 6-31 Control cables • Make sure that operation is smooth. • Lubricate if necessary. Drive chain • • • • Check chain slack. Adjust if necessary. Check chain condition. Lubricate if necessary.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM OPERATION AND IMPORTANT RIDING POINTS EAU15950 EAU16252 Starting the engine EWA10270 WARNING ● ● ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer regarding any control or function that you do not thoroughly understand. Never start the engine or operate it in a closed area for any length of time.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM OPERATION AND IMPORTANT RIDING POINTS ECA11130 CAUTION: EAU16671 Shifting ● For maximum engine life, always warm the engine up before starting off. Never accelerate hard when the engine is cold! 5 ECA10260 CAUTION: 1. Shift pedal 2. Neutral position ● Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc. The gear positions are shown in the illustration.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM OPERATION AND IMPORTANT RIDING POINTS 4. At the recommended shift points shown in the following table, close the throttle, and at the same time, quickly pull the clutch lever in. 5. Shift the transmission into second gear. (Make sure not to shift the transmission into the neutral position.) 6. Open the throttle part way and gradually release the clutch lever. 7. Follow the same procedure when shifting to the next higher gear.
U4C811E0.book Page 4 Thursday, June 7, 2007 2:38 PM OPERATION AND IMPORTANT RIDING POINTS ECA10301 EAU17212 CAUTION: Parking After 1000 km (600 mi) of operation, the engine oil must be changed and the oil filter cartridge or element replaced. When parking, stop the engine, and then remove the key from the main switch. 1600 km (1000 mi) and beyond The vehicle can now be operated normally. EWA10310 WARNING ● ECA10310 CAUTION: ● 5 ● Keep the engine speed out of the tachometer red zone.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU17231 EAU17301 PERIODIC MAINTENANCE Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your vehicle in the safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following pages.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EWA10340 WARNING Modifications not approved by Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes. EWA12371 WARNING Do not touch either muffler bracket, located under the muffler bracket covers, until the exhaust system has cooled. 6 1. Muffler bracket cover 2.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU17600 Periodic maintenance chart for the emission control system INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month ODOMETER READINGS 4000 mi (7000 km) or 6 months 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months Fuel line • Check fuel hoses for cracks or damage. • Replace if necessary.
U4C811E0.book Page 4 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU32185 General maintenance and lubrication chart INITIAL No. ITEM ROUTINE 600 mi (1000 km) or 1 month ODOMETER READINGS 4000 mi (7000 km) or 6 months 8000 mi 12000 mi 16000 mi 20000 mi (13000 km) (19000 km) (25000 km) (31000 km) or or or or 12 months 18 months 24 months 30 months 1 * Air filter element • Check condition and for damage. • Replace if necessary. 2 * Clutch • Check operation.
U4C811E0.book Page 5 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM ROUTINE Swingarm pivot bearings • Check bearing assemblies for looseness. • Moderately repack with lithiumsoap-based grease. Drive chain • Check chain slack, alignment and condition. • Adjust and lubricate chain with a special O-ring chain lubricant thoroughly. 11 * Steering bearings • Check bearing assemblies for looseness.
U4C811E0.book Page 6 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. 6 ITEM ROUTINE 17 Sidestand pivot • Check operation. • Apply lithium-soap-based grease (all-purpose grease) lightly. 18 * Sidestand switch • Check operation and replace if necessary.
U4C811E0.book Page 7 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR INITIAL No. ITEM ROUTINE Control cables • Apply Yamaha chain and cable lube or engine oil SAE 10W-30 thoroughly. 28 * Throttle grip housing and cable • Check operation and free play. • Adjust the throttle cable free play if necessary. • Lubricate the throttle grip housing and cable. 29 * Lights, signals and switches • Check operation. • Adjust headlight beam.
U4C811E0.book Page 8 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR • Every two years replace the internal components of the brake master cylinders and calipers, and change the brake fluid. • Replace the brake hoses every four years and if cracked or damaged.
U4C811E0.book Page 9 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU18712 Removing and installing cowlings and panels The cowlings and panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a cowling or panel needs to be removed and installed. 1. Panel B 2. Panel D 3. Cowling B 1. Quick fastener screw EAU42970 Cowlings A and B 6 1. 2. 3. 4.
U4C811E0.book Page 10 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 2. Fit the projections on the cowling into the slots and slide it forward. 1. Cowling B 2. Quick fastener 2. Disconnect the turn signal light lead coupler. 1. Bolt 2. Quick fastener screw 3. Cowling C 1. Slot 2. Projection 3. Install the quick fasteners and the quick fastener screws. 6 3. Slide the cowling backward to unhook its projections from the slots, and then pull the cowling off.
U4C811E0.book Page 11 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR To install the cowling 1. Insert the projections into the slots, and then slide the cowling forward. EAU36630 Panels C and D To remove one of the panels Remove the screw and the quick fastener, and then pull the panel off as shown. 1. Panel A 2. Screw 1. Slot 2. Projection 2. Place the cowling in its original position, and then install the quick fastener screws and the bolts. 3. Install cowling A.
U4C811E0.book Page 12 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU19652 Checking the spark plugs 6 The spark plugs are important engine components, which should be checked periodically, preferably by a Yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine.
U4C811E0.book Page 13 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU19681 NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. Canister (for California only) EAU19912 Engine oil and oil filter cartridge The engine oil level should be checked before each ride.
U4C811E0.book Page 14 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The engine oil should be between the minimum and maximum level marks. 2. Start the engine, warm it up for several minutes, and then turn it off. 3. Place an oil pan under the engine to collect the used oil. 4. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 1. Oil filter wrench 2. Engine oil filter cartridge 6 1. 2. 3. 4.
U4C811E0.book Page 15 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR Recommended engine oil: See page 8-1. Oil quantity: Without oil filter cartridge replacement: 2.90 L (3.07 US qt) (2.55 Imp.qt) With oil filter cartridge replacement: 3.10 L (3.28 US qt) (2.73 Imp.qt) 1. O-ring NOTE: Make sure that the O-ring is properly seated. 7. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. 1.
U4C811E0.book Page 16 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. NOTE: After the engine is started, the engine oil level warning light should go off if the oil level is sufficient.
U4C811E0.book Page 17 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● If water has been added to the coolant, have a Yamaha dealer check the antifreeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced. EWA10380 3. Place a container under the engine to collect the used coolant. 4. Remove the radiator cap. EWA10380 WARNING Never attempt to remove the radiator cap when the engine is hot.
U4C811E0.book Page 18 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 8. After the coolant is completely drained, thoroughly flush the cooling system with clean tap water. 9. Install the coolant reservoir by installing the bolts. 10. Install the coolant drain bolt, and then tighten it to the specified torque. 1. Coolant drain bolt 6 6. Remove the coolant reservoir cap. 7. Remove the coolant reservoir by removing the bolts, and then turn the reservoir upside down to empty it.
U4C811E0.book Page 19 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced. 13. Install the radiator cap, start the engine, let it idle for several minutes, and then turn it off. 14. Remove the radiator cap to check the coolant level in the radiator. If necessary, add sufficient coolant until it reaches the top of the radiator, and then install the radiator cap. 15.
U4C811E0.book Page 20 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ECA10480 CAUTION: ● ● 1. Screw 2. Air filter case cover 1. Air filter element 2. Air intake manifold ECA12880 CAUTION: 6 When removing the air filter case cover, be careful not to allow foreign objects to drop into the air intake manifold. 7. Check the condition of the air filter element and replace it if it is damaged or excessively dusty. 8.
U4C811E0.book Page 21 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● Be sure to place the fuel tank breather/overflow hose in its original position. EAU44730 Checking the engine idling speed EAU21382 Checking the throttle cable free play The engine idling speed must be checked as follows and, if necessary, adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U4C811E0.book Page 22 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU21401 EAU21750 Valve clearance Tires The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
U4C811E0.book Page 23 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR evenly from side to side. Properly adjust the suspension for your load, and check the condition and pressure of your tires. NEVER OVERLOAD YOUR VEHICLE. Make sure that the total weight of the cargo, rider, passenger, and accessories (cowling, saddlebags, etc. if approved for this model) does not exceed the maximum load of the vehicle.
U4C811E0.book Page 24 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● ● 6 Always make sure that the valve caps are securely installed to prevent air pressure leakage. Use only the tire valves and valve cores listed below to avoid tire deflation during a high-speed ride.
U4C811E0.book Page 25 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22011 Accessories and replacement parts any consequences caused by the use of items which have not been approved by Yamaha. EAU33890 Adjusting the clutch lever free play EWA10621 WARNING This vehicle is not designed to pull a trailer or to be attached to a sidecar.
U4C811E0.book Page 26 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU22270 NOTE: If the specified clutch lever free play cannot be obtained as described above, proceed as follows. 6 1. Fully turn the adjusting bolt at the clutch lever in direction (a) to loosen the clutch cable. 2. Loosen the locknut at the crankcase. 3. To increase the clutch lever free play, turn the adjusting nut in direction (a).
U4C811E0.book Page 27 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR wear indicator groove almost appears, have a Yamaha dealer replace the brake pads as a set. EAU22580 Checking the brake fluid level Front brake EAU22500 Rear brake pads 1. Minimum level mark Rear brake 1. Lining thickness Check each rear brake pad for damage and measure the lining thickness. If a brake pad is damaged or if the lining thickness is less than 1.0 mm (0.
U4C811E0.book Page 28 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● ● ● 6 Be careful that water does not enter the brake fluid reservoir when refilling. Water will significantly lower the boiling point of the fluid and may result in vapor lock. Brake fluid may deteriorate painted surfaces or plastic parts. Always clean up spilled fluid immediately. As the brake pads wear, it is normal for the brake fluid level to gradually go down.
U4C811E0.book Page 29 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Using the alignment marks on each side of the swingarm, make sure that both chain pullers are in the same position for proper wheel alignment. 3. Tighten the locknuts, then the axle nut to their specified torques. Tightening torques: Locknut: 16 Nm (1.6 m·kgf, 11 ft·lbf) Axle nut: 150 Nm (15.0 m·kgf, 110 ft·lbf) 1. Drive chain slack 4. If the drive chain slack is incorrect, adjust it as follows.
U4C811E0.book Page 30 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23022 Cleaning and lubricating the drive chain The drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrication chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas. Service the drive chain as follows.
U4C811E0.book Page 31 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23111 Checking and lubricating the throttle grip and cable The operation of the throttle grip should be checked before each ride. In addition, the cable should be lubricated at the intervals specified in the periodic maintenance chart.
U4C811E0.book Page 32 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU43070 Checking and lubricating the shift pedal EAU23200 Checking and lubricating the sidestand EAUM1650 Lubricating the swingarm pivots The swingarm pivots must be lubricated at the intervals specified in the periodic maintenance and lubrication chart.
U4C811E0.book Page 33 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23271 EAU23280 Checking the front fork Checking the steering The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart. 1.
U4C811E0.book Page 34 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU23290 Checking the wheel bearings EAU23441 Battery The front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrication chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a Yamaha dealer check the wheel bearings. 1. Positive battery lead (red) 2. Battery 3.
U4C811E0.book Page 35 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EWA10760 WARNING ● ● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID. • EXTERNAL: Flush with plenty of water. • INTERNAL: Drink large quantities of water or milk and immediately call a physician.
U4C811E0.book Page 36 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU42921 Replacing the fuses To access the main fuse The main fuse is located under the rider seat and can be accessed as follows: 1. Remove the rider seat. (See page 3-15.) 2. Move the ECU (Electronic Control Unit) away from the fuse. 6 1. ECU (Electronic Control Unit) 1. Main fuse 1.
U4C811E0.book Page 37 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR To replace a fuse If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuse box 1. 2. 3. 4. 5. Headlight fuse Ignition fuse Signaling system fuse ETV (Electric Throttle Valve) fuse Backup fuse (for odometer, clock and immobilizer system) 6. Right radiator fan fuse 7.
U4C811E0.book Page 38 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU42930 EWA10790 Replacing a headlight bulb WARNING Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 1. Headlight bulb cover 2. Headlight coupler 1. High beam headlight bulb 2. Low beam headlight bulb 6 This model is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows.
U4C811E0.book Page 39 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● Headlight lens Do not affix any type of tinted film or stickers to the headlight lens. Do not use a headlight bulb of a wattage higher than specified. 1. Headlight bulb cover 1. Headlight bulb holder 2. Disconnect the headlight coupler. EWA10790 WARNING Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 1.
U4C811E0.book Page 40 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR ● ● 6 Headlight bulb Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. Headlight lens Do not affix any type of tinted film or stickers to the headlight lens.
U4C811E0.book Page 41 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU24202 Replacing a turn signal light bulb 1. Remove the turn signal light lens by removing the screw. 1. Screw 2. Remove the defective bulb by pushing it in and turning it counterclockwise. 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screw. EAU24310 Replacing the license plate light bulb 1.
U4C811E0.book Page 42 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU33910 Replacing an auxiliary light bulb This model is equipped with two auxiliary lights. If an auxiliary light bulb burns out, replace it as follows. 1. Remove panel C (if replacing the left auxiliary light bulb) or panel D (if replacing the right auxiliary light bulb). (See page 6-9.) 2. Remove the auxiliary light bulb cover by removing the quick fastener.
U4C811E0.book Page 43 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU24350 Supporting the motorcycle Since this model is not equipped with a centerstand, follow these precautions when removing the front and rear wheel or performing other maintenance requiring the motorcycle to stand upright. Check that the motorcycle is in a stable and level position before starting any maintenance. A strong wooden box can be placed under the engine for added stability.
U4C811E0.book Page 44 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 3. Remove the brake hose holder and reflector on each side by removing the bolt and nut. 4. Remove the brake caliper on each side by removing the bolts. NOTE: Make sure that there is enough space between the brake pads before installing the brake calipers onto the brake discs. Tightening torque: Brake caliper bolt: 35 Nm (3.5 m·kgf, 25 ft·lbf) 1. Wheel axle ECA11050 CAUTION: 6 1. 2. 3. 4. 5. 6.
U4C811E0.book Page 45 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 7. Tighten wheel axle pinch bolt B, and then tighten pinch bolt A to the specified torque. 11. Retighten pinch bolt D to the specified torque. Tightening torque: Wheel axle pinch bolt: 21 Nm (2.1 m·kgf, 15 ft·lbf) EAU25080 Rear wheel EAU25311 To remove the rear wheel EWA10820 WARNING ● 12. While applying the front brake, push down hard on the handlebar several times to check for proper fork operation.
U4C811E0.book Page 46 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR 2. Lift the rear wheel off the ground according to the procedure on page 6-43. 3. Remove the axle nut. 4. Loosen the locknut on each side of the swingarm. 5. Turn the drive chain slack adjusting bolts fully in direction (a) and push the wheel forward. 6. Remove the drive chain from the rear sprocket. ● Make sure that there is enough space between the brake pads before installing the wheel. 1.
U4C811E0.book Page 47 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU25870 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power. The following troubleshooting charts represent quick and easy procedures for checking these vital systems yourself.
U4C811E0.book Page 48 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR EAU42500 Troubleshooting charts Starting problems or poor engine performance EWA10840 WARNING Keep away open flames and do not smoke while checking or working on the fuel system. 1. Fuel There is enough fuel. Check the compression. There is no fuel. Supply fuel. There is compression. Check the ignition. There is no compression. Have a Yamaha dealer check the vehicle. Check the fuel level in the fuel tank.
U4C811E0.book Page 49 Thursday, June 7, 2007 2:38 PM PERIODIC MAINTENANCE AND MINOR REPAIR Engine overheating EWAT1040 WARNING ● ● Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled. Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM MOTORCYCLE CARE AND STORAGE EAU37833 Matte color caution ECA15192 CAUTION: Some models are equipped with matte colored finished parts. Be sure to consult a Yamaha dealer for advice on what products to use before cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds when cleaning these parts will scratch or damage their surface. Wax also should not be applied to any matte colored finished parts.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM MOTORCYCLE CARE AND STORAGE ● ● ● with mild detergent, alkaline products and a soft brush may be used. Do not use any harsh chemical products on plastic parts or the mufflers. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM MOTORCYCLE CARE AND STORAGE ● ● ● 7 not be thoroughly cleaned with mild detergent, alkaline products and a soft brush may be used. Never use compounds or other special treatments to clean the titanium mufflers, as they will remove the finish on the outer surface of the mufflers. Even the smallest amounts of oil, such as from oily towels or fingerprints, will leave stains on the titanium mufflers, which can be removed with a mild detergent.
U4C811E0.book Page 4 Thursday, June 7, 2007 2:38 PM MOTORCYCLE CARE AND STORAGE EAU26201 Storage Short-term Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. ECA10810 CAUTION: ● ● Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM SPECIFICATIONS Dimensions: Overall length: 2060 mm (81.1 in) Overall width: 720 mm (28.3 in) Overall height: 1110 mm (43.7 in) Seat height: 835 mm (32.9 in) Wheelbase: 1415 mm (55.7 in) Ground clearance: 135 mm (5.31 in) Minimum turning radius: 3400 mm (133.9 in) Weight: With oil and fuel: 200.0 kg (441 lb) Engine: 8 Engine type: Liquid cooled 4-stroke, DOHC Cylinder arrangement: Forward-inclined parallel 4-cylinder Displacement: 998.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM SPECIFICATIONS Gear ratio: 1st: 38/15 (2.533) 2nd: 33/16 (2.063) 3rd: 37/21 (1.762) 4th: 35/23 (1.522) 5th: 30/22 (1.364) 6th: 33/26 (1.269) Chassis: Frame type: Diamond Caster angle: 24.00 ° Trail: 102.0 mm (4.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM SPECIFICATIONS Electrical system: Ignition system: Transistorized coil ignition (digital) Charging system: AC magneto Battery: Model: YTZ10S Voltage, capacity: 12 V, 8.6 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage × quantity: 8 Headlight: 12 V, 55.0 W × 4 Tail/brake light: LED Front turn signal/position light: 12 V, 21 W/5.0 W × 2 Rear turn signal light: 12 V, 21.0 W × 2 Auxiliary light: 12 V, 5.0 W × 2 License plate light: 12 V, 5.
U4C811E0.book Page 1 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU26351 Identification numbers EAU26381 EAU26400 Key identification number Vehicle identification number 1. Key identification number 1. Vehicle identification number The key identification number is stamped into the key tag. Record this number in the space provided and use it for reference when ordering a new key. The vehicle identification number is stamped into the steering head pipe.
U4C811E0.book Page 2 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU33941 Model label 1. Muffler bracket cover 2. Muffler bracket 1. Model label The model label is affixed to the frame under the passenger seat. (See page 3-15.) Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
U4C811E0.book Page 3 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU26551 Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A.
U4C811E0.
U4C811E0.book Page 5 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
U4C811E0.
U4C811E0.book Page 7 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha motorcycles will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.
U4C811E0.book Page 8 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION WARRANTY QUESTIONS AND ANSWERS CUSTOMER SERVICE Q. What costs are my responsibility during the warranty period? A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plugs, and brake shoes.
U4C811E0.book Page 9 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION EAU26750 YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.). In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.
U4C811E0.book Page 10 Thursday, June 7, 2007 2:38 PM CONSUMER INFORMATION We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need. Yamaha Service Marketing P.O.
U4C811E0.book Page 1 Thursday, June 7, 2007 3:09 PM INDEX A Accessories and replacement parts ..... 6-25 Air filter element, checking and replacing............................................. 6-19 Auxiliary light bulb, replacing ................ 6-42 EXUP system ........................................3-21 Front and rear brake pads, checking ....6-26 Front fork, adjusting ..............................3-17 Front fork, checking...............................6-33 Fuel ......................................
U4C811E0.book Page 2 Thursday, June 7, 2007 3:09 PM INDEX Throttle grip and cable, checking and lubricating ........................................... 6-31 Tires ...................................................... 6-22 Tool kit .................................................... 6-1 Troubleshooting .................................... 6-47 Troubleshooting charts ......................... 6-48 Turn signal indicator lights ...................... 3-2 Turn signal light bulb, replacing ............
U4C811E0.
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2007.06-3.
