AV RECEIVER RX-V596/HTR-5250 RX-V596RDS SERVICE MANUAL IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.
RX-V596/HTR-5250/RX-V596RDS ■ TO SERVICE PERSONNEL 1. Critical Components information Components having special characteristics are marked ! and must be replaced with parts having specifications equal to those originally installed. WALL 2. Leakage Current Measurement (For 120V Model only) OUTLET When service has been completed, it is imperative that you verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohm shunted by 0.
RX-V596/HTR-5250/RX-V596RDS ■ SPECIFICATIONS ■AUDIO SECTION Minimum RMS Output Power Per Channel (Power Amp. Section) U, C models MAIN L/R, REAR L/R 20Hz to 20kHz, 0.06% THD, 8Ω 100W+100W 1kHz, 0.09% THD, 8Ω 110W+110W CENTER 20Hz to 20kHz, 0.06% THD, 8Ω 100W 1kHz, 0.09% THD, 8Ω 110W R,T,A,B,G,L models MAIN L/R, REAR L/R 20Hz to 20kHz, 0.06% THD, 8Ω 70W+70W 1kHz, 0.09% THD, 8Ω 80W+80W CENTER 20Hz to 20kHz, 0.06% THD, 8Ω 70W 1kHz, 0.
349.5(13-3/4") 530 to 1710kHz 530 to 1710kHz 531 to 1611kHz 531 to 1611kHz 300µV/m 52dB 150mV Loop antenna BL........Black model TI.........Titan model GD.........Gold model 435(17-1/8") 151(5-15/16") 130(5-3/32") ■GENERAL Power Supply U, C models AC120V, 60Hz R model AC110/120/220/240V, 50/60Hz T model AC220V, 50Hz A model AC240V, 50Hz B, G, L models AC230V, 50Hz Power Consumption U model 280W C model 310W/410VA R, T models 310W A, B, G, L models 300W Standby Power Consumption U, C, models 0.
RX-V596/HTR-5250/RX-V596RDS ■ INTERNAL VIEW 12 3 4 5 67 890 AB CD E F 1 2 3 4 5 6 7 G H I J ■ DISASSEMBLY PROCEDURES (Remove parts in disassembly order as numbered.) K LM N 8 9 0 A B C D E F G H I J K L M N POWER TRANSFORMER P.C.B. POWER (2) P.C.B. POWER (7) (U,C,A,B,G,L models only) P.C.B. MAIN (3) P.C.B. POWER (6) (R,T models only) P.C.B. MAIN (4) P.C.B. POWER (4) (R,T models only) P.C.B. MAIN (2) P.C.B. MAIN (1) P.C.B. POWER (3) P.C.B. INPUT (1) P.C.B. INPUT (4) P.C.B. INPUT (3) P.C.B.
RX-V596/HTR-5250/RX-V596RDS ■ SELF DIAGNOSIS FUNCTION 1. PURPOSE AND OPERATION The RX-V596/HTR-5250/RX-V596RDS has a Self Diagnosis Function to locate a faulty part, if any, by inspecting and taking measurements. There are 12 main items in the diagnostic menu and sub-menu items as listed below. No. MAIN MENU 1 ANALOG THROUGH 1. MAIN BYPASS 2. DSP 0dB 7A–88 ("1" [DSP mode]) ––– 2 DSP THROUGH 1. YSS+SRAM M 2. YSS M 3. DSP FULL BIT 7A–89 ("2" [DSP mode]) ––– ––– 3 AC–3/DTS THROUGH 1.
RX-V596/HTR-5250/RX-V596RDS 2. BEGINNING AND CANCELLATION (1) Starting up the function and the display After starting up, main-menu No.1 is selected. A. How to start diagnostic program Using the front panel keys of the main unit. Plug in the AC power cord. With the Power OFF, hold down the "PRESET/TUNING simultaneously (Step 1), then press the "STANDBY/ON" key (Step 2). Sub menu No. 1 of the diagnosis main menu No. 1 will start.
RX-V596/HTR-5250/RX-V596RDS ● FL display at start-up of diagnostic program When the diagnostic program has started, the check sum of the main microcomputer or the protection history (*1) is displayed. If the protection function has been activated in the past, the type and voltage value are displayed. After a few seconds the diagnosis function menu will appear.
RX-V596/HTR-5250/RX-V596RDS 3. OPERATION AND DISPLAY WHEN STARTING DIAGNOSIS FUNCTION (1) Selection of diagnostic menu The diagnostic menu and the sub-menu can be selected by using the front panel keys of the main unit or the remote control unit. ● Selection by using the front panel keys of the main unit The main menu can be changed cyclically by using the "PROGRAM / " keys, and the sub-menu, by using the "PRESET/TUNING / " keys. The " " key will increase the main or sub-menu number.
RX-V596/HTR-5250/RX-V596RDS 4. CONTENTS OF DIAGNOSIS FUNCTION This section describes the contents of the Self Diagnosis Function in detail. No.1 ANALOG THROUGH The input is fixed to analog (A/D). There are two sub-menus. 1. MAIN BYPASS 1 MA I N B Y P A S S The L/R signals bypass the digital circuit, and are output to the MAIN L/R. The L/R signals are output without being processed to the CENTER/SUBWOOFER, FRONT L/R and REAR L/R through the DSP. (Remote control code 7A-88: "1" key [DSP mode]) CODEC.
RX-V596/HTR-5250/RX-V596RDS No.2 DSP THROUGH The input is automatically discriminated by signal detection and switched with priorities Coaxial>Optical>Analog. There are the following three sub-menus. 1. YSS+SRAM 2 Y S S + S R AM M The L/R signals are output without being processed to the MAIN L/R through the AC3D2av. The L/R signals are output without being processed to the CENTER/SUBWOOFER through the DSP. The (L+R)/2 signals are output to the FRONT L/R and REAR L/R through the DSP and the SRAM.
RX-V596/HTR-5250/RX-V596RDS No.3 AC-3/DTS THROUGH The input is digital signal only. AC-3 (DOLBY DIGITAL) or DTS Digital Surround decoding operation is executed, according to the input source. bit 1 bit 7 1. STATUS(BINARY FORM) 3 ST : 1 0 0 0 1 0 0 1 AC-3 (DOLBY DIGITAL) decoded signals are output to each channel via AC3D2av. The AC-3 (DOLBY DIGITAL) signal status data will be displayed in the FL display using a binary number. CODEC.
RX-V596/HTR-5250/RX-V596RDS No.5 SPEAKERS SET The input is automatically discriminated by signal detection and switched with priorities Coaxial>Optical>Analog. The L/R signals are output to channels specified by the sub-menu without being processed. There are the following nine sub-menus items. Signal routes of the sub-menu 1-4 are the same as EFFECT OFF. But MAIN L/R are signals through the digital circuit. Signal routes of the sub-menu 5-9 are the same as "2. YSS M" of "No. 2 DSP THROUGH".
RX-V596/HTR-5250/RX-V596RDS No.6 DISPLAY CHECK Check program for FL display. The display status will change as follows with sub-menu operation. signal route is the same as "2. EFFECT OFF" of "No. 4 PRO LOGIC". 6 V FD CHCK Initial display All segments turn off All segments turn on (see page 35) Software Release date display (lattice form) Alternate segments turn on A defect of the FL drive port and FL display segments can be detected by using "All segments turn off" and "All segments turn on".
RX-V596/HTR-5250/RX-V596RDS No.9 AD DATA CHECK The A/D conversion values of the microcomputer which detects key scan port, protection detection port, etc. are displayed in % (100%:5V). Signal route is the same as "2. EFFECT OFF" of "No. 4 PRO LOGIC". The keys on the main unit cannot be operated to detect the values of all keys in the K1/K2 and SI. Operating the "PROGRAM , "key and turning the rotary encoder ("INPUT SELECTOR" on the main unit) will switch the sub-menu. Initial display.
RX-V596/HTR-5250/RX-V596RDS No.10 STATUS INFORMATION FROM DSP The status data from the DSP block is sequentially displayed in a hexadecimal number. Signal route is the same as "2. EFFECT OFF" of "No. 4 PRO LOGIC".
RX-V596/HTR-5250/RX-V596RDS No.11 EEPROM WRITING FUNCTION The check sum value confirmation of EEPROM and data writing. Signal route is the same as "2. EFFECT OFF" of "No. 4 PRO LOGIC". M : XXXX E : XXXX M:XXXX: The check sum value is displayed when the microcomputer has ROM modification data. 0000 is displayed when there is no data. E:XXXX: The check sum value is displayed when the EEPROM is installed on and it has the ROM data . 000 is displayed when EEPROM is not mounted on or data is unusual.
RX-V596/HTR-5250/RX-V596RDS ■ FACTORY PRESET All of the system settings are initially set from the factory as follows. ● INPUT SELECTOR ● EFFECT LEVEL INPUT ROTARY ENCODER MONITOR EXTERNAL PHONO CD TUNER DVD/LD D-TV VCR V-AUX CBL/SAT TAPE/MD EXT. DECODER FACTORY PRESET PROGRAM CONCERT HALL DISCO ROCK CONCERT SCI-FI TV SPORTS DOLBY NORMAL DOLBY ENHANCED ROCK CONCERT EFFECT OFF NONE EFFECT CHANNEL CENTER RIGHT SURROUND LEFT SURROUND SUBWOOFER PRESET VALUE 0 dB 0 dB 0 dB 0 dB ● DSP PROGRAM No. 1. 2.
RX-V596/HTR-5250/RX-V596RDS ■ AMP ADJUSTMENT Confirmation of Idling Current of Main Amplifier • Right after power is turned on, confirm that the voltage across the terminals of R688(Main Lch),R690(Main Rch), R692(Center), R694(Rear Lch), R696(Rear Rch) are between 0.1mV and 10.0mV. • If it exceeds 10.0mV, open (cut off) R571 (Main Lch), R577 (Main Rch), R583 (Center), R589 (Rear Lch), R595 (Rear Rch) and • reconfirm the voltage. Confirm that the voltage is 0.20mV ~ 15.0mV after 60 minutes. 0.1mV ~ 10.
RX-V596/HTR-5250/RX-V596RDS ■ TUNER ADJUSTMENT ● Measuring Instruments ● Dummy antenna 1) FM signal generator (FM SG) 2) Stereo signal generator (SSG) FM dummy antenna 3) AM signal generator (AM SG) 4) Distortion meter (DIST.
RX-V596/HTR-5250/RX-V596RDS FM Adjustment ● Before Adjustment 4) Set each switch to the following position unless otherwise 1) For dBµ, 1µV=0dBµ applies. Example : 60dBµ=1mV 2) 100% modulation means that the frequency deviation is specified. INPUT SELECTOR ....... TUNER TUNING MODE ............. AUTO ±75kHz. 3) Install the Matching Transformer and connect FM SG. ● Connection diagram (Measuring instruments) 1) Discriminator balance adjustment. FM SG TP1 FM ANT GND TUNER P. C. B.
RX-V596/HTR-5250/RX-V596RDS See page 22 for TP locations & adjustment points. Step Adjustment item FM ANT (75Ω) 98.1MHz 30dBµ MONO 1kHz 100% modulation 98.1MHz ✽(A-4) Verification of monaural distortion FM ANT (75Ω) 98.1MHz 70dBµ MONO 1kHz 100% modulation Verification of stereo distortion Adjustment point Rating Adjust so that the meter is maximum. CAUTION: Over-adjustment of the IFT core will reduce the sensitivity. (Maximum±90°) 98.1MHz ✽(A-4) REC OUT L, R 0.
RX-V596/HTR-5250/RX-V596RDS AM Adjustment (This should be done after FM adjustment.) ● Connection diagram (Measuring instruments) 1) Adjustment of sensitivity. AM loop antenna L AM ANT AM SG AM dummy antenna TUNER P.C.B ACVM R REC OUT GND DIST. M Oscilloscope See page 22 for TP locations & adjustment points.
RX-V596/HTR-5250/RX-V596RDS ■ IC DATA P50/FL08 P51/FL09 P52/FL10 P53/FL11 P54/FL12 P55/FL13 P56/FL14 P57/FL15 P00/FL16 P01/FL17 P02/FL18 P03/FL19 P04/FL20 P05/FL21 P06/FL22 VSS P07/FL23 VCC P10/FL24 P11/FL25 P12/FL26 P13/FL27 P14/FL28 P15/FL29 P16/FL30 P17/FL31 P20/FL32 P21/FL33 P22/FL34 P23/FL35 IC501 : M30217MA-A203FP 16-bit Microcomputer 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P67/FL07 P66/FL06 P65/FL05 P64/FL04 P63/FL03 P62/FL02 P61/FL01 P60/FL00 VEE
RX-V596/HTR-5250/RX-V596RDS IC501 : M30217MA-A203FP 16-bit Microcomputer Pin No. 1 P97 Pin Name SCK 2 3 P96 P95 SDT RCK O Serial Data output O Clock output for model type 32 P46/FL54 33 P45/FL53 4 /CK2 P94 RDT distinction (*1) O Data output for destination distinction 5 /SO2 P93 DEST 6 /SI2 P92 7 Port I/O Function For Input selector Tuner, etc. Pin Port No.
RX-V596/HTR-5250/RX-V596RDS IC501 : M30217MA-A203FP 16-bit Microcomputer Pin Port No. 67 P05/FL21 Pin Name P1 O Segment 1 for FL display Pin Port No.
RX-V596/HTR-5250/RX-V596RDS PCO 2 27 SI AVSS 3 26 SO M/S 4 25 /CS DDIN 5 24 VDD TEST 6 23 INT /IC 7 22 /LOCK 21 ERR XO 9 20 DBL XI 10 19 FS128 TOP VIEW VSS 8 MCK 11 18 SYNC VDD 12 17 VSS SDO 13 16 SDMCK SDBCK 14 15 SDWCK Pin No.
RX-V596/HTR-5250/RX-V596RDS IC4 : YSS918D-F (AC3D2av) VSS RAMD7 RAMD6 RAMD5 RAMD4 RAMD3 RAMD2 RAMD1 RAMD0 VDD1 RAMA2 SCK SI SO /CS /CSB RAMA3 TEST /IC RAMA4 VSS RAMA5 RAMA6 /SDBCK0 SURENC KARAOKE MUTE CRC NONPCM VDD2 DSP + AC-3(Dolby Digital)/ Pro Logic/ DTS Digital Surround Decoder 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 VDD SDWCK0 SDBCK0 SDIA0 SDIA1 RAMA1 RAMA0 RAMWEN RAMOEN VSS VDD IPORT7 IPORT6 IPORT5 IPORT4 IPORT3 IPORT2 IPORT1 IPORT0 VSS 81 50
RX-V596/HTR-5250/RX-V596RDS IC4 : YSS918D-F (AC3D2av) DSP + AC-3(Dolby Digital)/ Pro Logic/ DTS Digital Surround Decoder No.
RX-V596/HTR-5250/RX-V596RDS IC4 : YSS918D-F (AC3D2av) DSP + AC-3(Dolby Digital)/ Pro Logic/ DTS Digital Surround Decoder No.
RX-V596/HTR-5250/RX-V596RDS IC5 : IS61C1024-20J (1M SRAM) 131072-word x 8-bit High Speed Static RAM NC 1 32 VCC A3 2 31 A2 A4 3 30 CE2 A5 4 29 /WE A6 5 28 A1 A7 6 27 A0 A8 7 A9 8 A10 TOP VIEW 27,28 31, A0-A16 2-12, 23,25 26 DECODER 131072-word x 8-bit MEMORY ARRAY (512-row x 2048-column) 13-15, 17-21 I/O DATA CONTROL COLUMN I/O 26 A16 D1-D8 25 A15 9 24 /OE A11 10 23 A14 /CE1 22 A12 11 22 /CE1 CE2 30 A13 12 21 D8 /WE 29 D1 13 20 D7 /OE 24 D2 14 19 D6 D3 15 1
RX-V596/HTR-5250/RX-V596RDS SDOS 1 33 VREFL OCKS 2 32 RIN+ M/S 3 31 RIN– BICK 4 30 LIN+ 5 LRCK 29 TOP VIEW LIN– SDTI1 6 28 ROUT1 SDTI2 7 27 LOUT1 SDTI3 8 26 ROUT2 SDTO 9 25 LOUT2 DAUX 10 24 ROUT3 LOUT3 CAD0 22 CAD1 21 ICKS0 20 ICKS1 19 XTS 18 /PD 17 DVSS 16 DVDD 15 MCKO 14 23 DEM0 13 11 DEM1 12 DFS Pin No.
RX-V596/HTR-5250/RX-V596RDS ■ DISPLAY DATA ● V501 : 16-BT-71GK (V4193300) y 1 PATTERN AREA • PIN CONNECTION Pin No. 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 9 CONNECTION F1 F1 NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP Fd Fd NP NP P22 P21 P20 P19 Pin No. 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CONNECTION P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 NP NP 16G 15G 14G 13G 12G Pin No. NOTE 1) F1, F2.........
RX-V596/HTR-5250/RX-V596RDS ■ BLOCK DIAGRAM (1/2) INPUT SELECTOR CONTROL COAXIAL SIGNAL DETECTOR IC371 6-CH SELECTOR IC102 DIA DIB 8 OPTICAL 1M SRAM STATIC RAM IC5 OPTICAL 16 4 10 R+ R- IC10B 30 3 1 29 2 27 INPUT SELECTOR CONTROL 2 29 IC8,9 5 7 6 26 FR 9 32 24 85 7 5 3 1 3 LFE 7 6 5 CENTER 6 7 5 IC402A 14 7 5 IC402B 3 1 3 C 1 3 3 IC403B 23 22 INPUT SELECTOR IC101 L 2 30 29 TAPE MONITOR IC102 1 L L Q107 Q522 Q530,Q533 Q531A/C RY501 Q120 15 7
RX-V596/HTR-5250/RX-V596RDS ■ BLOCK DIAGRAM (2/2) PK1 FM ANT RF AMP AM/FM IF DET. IC1 LA1266 CERAMIC CERAMIC FILTER FILTER IF AMP Fi 1 Fi 2 MIX 1 7 IF U,C,R,T models FM DET COIL J41 56 FM IF FM IF LOCAL OSC T3 QUADRATURE DET 0 2 1 LEVEL DET AM IF AM COIL PACK PK2 CONTROL AM IF AM DET E H AM IF COIL OSC VT Fi 3 T2 J 5 L 7 R TUNER DECODER VCO STOP A BUFFER 58 FM/AM MUTING G S.CURVE AM ANT T5 L.P.F.
RX-V596/HTR-5250/RX-V596RDS PARTS LIST ■ ELECTRICAL PARTS ■ WARNING Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. ● Carbon resistors (1/6W or 1/4W) are not included in the ELECTRICAL PARTS List. For the part Nos. of the carbon resistors,refer to page 86. ● Chip resistors are listed on page 81. ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS: C. A. EL. CHP C. CE C. CE. ARRAY C. CE. CHP C. CE. ML C. CE. M. CHP C.
RX-V596/HTR-5250/RX-V596RDS P. C. B. DSP Schm Ref ✻ ✻ CB1 CB3 CB6 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C20 C21 C22 C23 C32 C33 C34 C35 C44 C45 C46 C47 C48 C50 C51 C52 C53 C54 C55 C56 C59 C61 C62 C63 C64 C65 C66 C67 C68 C69 C70 C71 C72 C73 C74 C75 C76 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. DSP & P. C. B. OPERATION Schm Ref C138 C139 C140 C141 C150 C151 C152 C153 C154 C155 C156 C157 C158 C159 C160 C161 C162 C163 C164 C165 C166 C167 ✻ C168 ✻ C169 C170 C175 D1 D2 D4 D5 D6 D7 D8 D9 D10 D11 D12 D14 D15 D16 D17 D150 D151 D152 G1 G2 G3 G4 IC1 IC2 ✻ IC3 IC4 ✻ IC5 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. OPERATION & P. C. B. INPUT Schm Ref C509 C510 C511 C512 C513 C514 C515 C516 ✻ C581 ✻ C582 C583 ✻ C584 C585 ✻ C586 C587 C588 C589 C590 C591 C592 C593 C594 C595 C596 C597 C598 C599 C600 C621 C622 C623 C624 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D511 D512 ✻ IC501 IC502 IC581 IC582 JK621 PJ621 PN501 Q501 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. INPUT Schm Ref CB303 CB331 CB351 ✻ CB371 ✻ CB372 ✻ CB373 ✻ CB374 C102 C103 C104 C105 C107 C108 C109 C112 C113 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 ✻ C128 C129 C130 C131 C132 C133 C134 C135 ✻ C136 C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. INPUT Schm Ref C302 C303 C304 C305 C306 C307 C309 C310 C331 C332 C333 C334 C335 C336 C337 C351 C352 C353 C354 C355 C356 C357 C358 C360 C362 C363 C364 C365 C366 C367 C368 C371 C372 C373 C374 C375 C376 C377 C378 C379 C380 C381 C382 C383 C384 C385 C386 C387 C388 C389 C390 C391 D101 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. INPUT & P. C. B. POWER Schm Ref Q121 Q124 Q125 R141 R154 R155 R155 R156 R156 R216 R216 R217 R217 R222 R231 R231 R232 R232 R245 R246 R386 ✻ ✻ ✻ ✻ ✻ CB401 CB451 CB721 CB722 CB801 CB802 CB803 CB804 CB805 CB806 CB851 CB852 C401 ✻ C402 ✻ C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. POWER & P. C. B. MAIN ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Schm Ref ✻ C804 ✻ C805 C806 C807 C808 D401 D451 D452 ✻ D453 D721 D722 D801 D803 D804 D805 D806 D807 F801 F802 F802 F851 HS801 IC401 IC402 IC403 IC404 IC721 IC722 IC723 IC724 IC725 Q721 Q722 Q801 Q802 R411 R412 R435 R451 R452 R725 R726 R727 R728 R729 ✻ R730 R731 R802 R803 RY801 ST801 SW851 ✻ T801 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. MAIN Schm Ref ✻ C526 C527 ✻ C528 C529 ✻ C530 C531 C532 ✻ C533 C534 C535 C536 C537 C538 C539 ✻ C540 C541 C542 ✻ C543 C544 C545 ✻ C546 ✻ C547 C548 C549 ✻ C550 C551 ✻ C552 C553 ✻ C554 ✻ C555 C556 ✻ C557 ✻ C558 ✻ C559 ✻ C560 C561 C562 C563 ✻ C564 C565 C568 C569 C570 C573 C574 C575 C576 C577 C578 C579 C580 C581 ✻ C582 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. MAIN ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Schm Ref ✻ D528 ✻ D529 ✻ D530 D531 D532 ✻ D751 ✻ D752 D759 D760 D761 D762 D763 D764 D765 D766 D767 D768 G501 JK711 ✻ PJ501 PJ701 PN501 PN502 PN503 PN504 PN505 PN506 Q506 Q507 Q508 Q509 Q510 Q511 ✻ Q512 Q513 ✻ Q514 Q515 ✻ Q516 Q517 ✻ Q518 Q519 ✻ Q520 Q521 Q522 Q523 Q524 Q525 ✻ Q526 Q526 Q527 Q528 ✻ Q529 Q529 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. MAIN ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Schm Ref ✻ R578 ✻ R579 R579 R580 R580 ✻ R581 ✻ R582 ✻ R583 ✻ R584 R585 R585 R586 R586 ✻ R587 ✻ R588 ✻ R589 ✻ R590 R591 R591 R592 R592 ✻ R593 ✻ R594 ✻ R595 ✻ R596 R597 R597 R598 ✻ R599 R600 R600 R602 R603 ✻ R605 R607 R608 R609 ✻ R610 R611 R612 ✻ R614 R615 R616 ✻ R617 R619 R624 R629 R634 R639 R644 R653 R660 R661 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. TUNER • Lead Type Schm Ref CB4 C1 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C36 C36 C37 C37 C37 C38 C39 C39 C40 C40 C41 C41 C42 C43 PART NO.
RX-V596/HTR-5250/RX-V596RDS P. C. B. TUNER Schm Ref TE1 TP1 TP2 VR1 VR2 XL1 XL2 XL3 Description PART NO. VU477800 VT969000 VT969000 VJ694000 VJ694000 VY734600 GG000750 V3930900 BB071360 VR282500 TERM.ANT PIN.TEST PIN.TEST VR.TRIM VR.TRIM RSNR.CRYS RSNR.CE RSNR.CRYS SCR.TERM PLATE AJ-2038-040 IRS-2049 IRS-2049 B47KΩ B47KΩ 7.2MHz 456KHz 4.332MHz 8.3x13 ANT.
RX-V596/HTR-5250/RX-V596RDS ! ! ! ! ! ! ! ! ! ! Ref. No. 7 7 7 ✻ 8 ✻ 8 ✻ 10 ✻ 10 ✻ 10 ✻ 10 ✻ 10 ✻ 15 ✻ 15 ✻ 15 ✻ 15 ✻ 15 16 ✻ 16 16 16 16 17 23 24 25 26 27 ✻ 28 101 101 101 102 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 ✻ 103 109 110 112 120 120 120 ✻ 121 ✻ 121 121 ✻ 122 122 PART NO.
RX-V596/HTR-5250/RX-V596RDS ✻ ✻ ✻ ✻ ✻ ✻ Ref. No. 122 123 123 123 124 124 124 128 131 131 131 132 132 132 135 137 138 155 160 161 162 163 166 167 168 170 171 171 171 176 178 ✻ 200 ✻ 200 200-1 201 202 203 204 PART NO.
RX-V596/HTR-5250/RX-V596RDS Parts List for Carbon Resistors Value 1.0 Ω 1.8 Ω 2.2 Ω 3.3 Ω 4.7 Ω 5.6 Ω 10 Ω 15 Ω 22 Ω 27 Ω 33 Ω 39 Ω 47 Ω 56 Ω 68 Ω 75 Ω 82 Ω 91 Ω 100 Ω 110 Ω 120 Ω 150 Ω 160 Ω 180 Ω 200 Ω 220 Ω 270 Ω 330 Ω 390 Ω 430 Ω 470 Ω 510 Ω 560 Ω 680 Ω 820 Ω 910 Ω 1.0 kΩ 1.2 kΩ 1.5 kΩ 1.8 kΩ 2.0 kΩ 2.2 kΩ 2.4 kΩ 2.7 kΩ 3.0 kΩ 3.3 kΩ 3.6 kΩ 3.9 kΩ 4.7 kΩ 5.1 kΩ 5.6 kΩ 6.8 kΩ 8.2 kΩ 9.1 kΩ ❊: Not available 1/4W Type Part No.
RX-V596/HTR-5250/RX-V596RDS (RAV210 or RAV211) • U,C,R,T,A and L models → RAV210 • B and G models → RAV211 Key Arrangement ■ REMOTE CONTROL TRANSMITTER SCHEMATIC DIAGRAM U1 ROTARY SWITCH AMP/TUNER TAPE/MD VCR P46/KR6 5 P47/KR7 4 P00 36 Q2 2N3904 VDD 1 SW1 JRS1901 6 10 VDD P17 VBAT 5 + BATT 1.5Vx4 C2 0.1µF C1 470µF VDD R7 470kΩ R6 C7 0.1µF 1kΩ R9 220KΩ Q3 C6 0.
RX-V596/HTR-5250/RX-V596RDS List of the Yamaha Code (NEC Format) Key No.
RX-V596/HTR-5250/RX-V596RDS