AV RECEIVER RX-V367/HTR-3063 SERVICE MANUAL When the following parts are replaced, the model name and the destination MUST be written to the back-up IC (EEPROM: IC222 of the DIGITAL P.C.B.) to have proper operation. (See No. 22 SOFT SWITCH menu of the selfdiagnostic function.) • • EEPROM (IC222) of DIGITAL P.C.B. DIGITAL P.C.B. T F IMPORTANT NOTICE A R This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
RX-V367/HTR-3063 ■ TO SERVICE PERSONNEL WALL OUTLET 1. Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits.
RX-V367/HTR-3063 ■ FRONT PANELS Top view RX-V367 / HTR-3063 Front view RX-V367 (U, C, T models) A R RX-V367/HTR-3063 D RX-V367 (R, K, A, B, G, F, L models) T F 3
RX-V367/HTR-3063 HTR-3063 (U, C, T models) T F HTR-3063 (R, K, A, G, F, L models) A R RX-V367/HTR-3063 D 4
RX-V367/HTR-3063 ■ REAR PANELS RX-V367 (U model) T F RX-V367 (C model) A R RX-V367/HTR-3063 D RX-V367 (R model) 5
RX-V367/HTR-3063 RX-V367 (T model) T F RX-V367 (K model) A R RX-V367/HTR-3063 D RX-V367 (A model) 6
RX-V367/HTR-3063 RX-V367 (B, G, F models) T F RX-V367 (L model) A R RX-V367/HTR-3063 D HTR-3063 (U model) 7
RX-V367/HTR-3063 HTR-3063 (C model) T F HTR-3063 (R model) A R RX-V367/HTR-3063 D HTR-3063 (T model) 8
RX-V367/HTR-3063 HTR-3063 (K model) T F HTR-3063 (A model) A R RX-V367/HTR-3063 D HTR-3063 (G, E, F models) 9
RX-V367/HTR-3063 HTR-3063 (L model) A R T F RX-V367/HTR-3063 D 10
RX-V367/HTR-3063 ■ REMOTE CONTROL PANELS RAV331 (U, C models) RAV332 (R, T, K, A, L models) RAV333 (B, G, E, F models) Sheet (T model) T F RX-V367/HTR-3063 D A R 11
RX-V367/HTR-3063 ■ SPECIFICATIONS ■ Audio Section Minimum RMS Output Power (Power Amp. Section) (1 kHz, 0.9 % THD) U, C models (8 ohms) FRONT L/R .......................................................... 100 W/ch CENTER ................................................................... 100 W SURROUND L/R ................................................. 100 W/ch R, T, K, A, B, G, F, L models (6 ohms) FRONT L/R .......................................................... 100 W/ch CENTER ....................
RX-V367/HTR-3063 ■ AM Section Tuning Range U, C models .............................................. 530 to 1,710 kHz R, L models ........................ 530 to 1,710 / 531 to 1,611 kHz T, K, A, B, G, F models .............................. 531 to 1,611 kHz U ........................U.S.A. model C ..................Canadian model R .....................General model T..................... Chinese model K ...................... Korean model A .................Australian model B .......................
RX-V367/HTR-3063 • SELECT MENU MUSIC STEREO MUSIC ENHANCER SUR. DECODE STRAIGHT Surround Decoder ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● D *1 ● ● ● ● ● △ ● RX-V367/HTR-3063 △ : Setting is possible only when Pro Logic II Music is selected using decode type.
RX-V367/HTR-3063 • SET MENU TABLE MAIN MENU 1 Speaker Setup SUB-MENU 1 Config 2 Level 3 Distance PARAMETER VALUE [INITIAL VALUE] Subwoofer Front speaker Center speaker Surround speaker L/R Crossover Subwoofer Phase Extra Bass FL (Front speaker L) FR (Front speaker R) C (Center speaker) SL (Surround speaker L) SR (Surround speaker R) SWFR (Subwoofer) Unit Front L Front R Center [Yes] / None Small / [Large] None / [Small] / Large 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz [NRM] / REV On / [O
RX-V367/HTR-3063 MAIN MENU 4 DSP Parameter SUB-MENU MOVIE Standard Spectacle Sci-Fi Adventure Drama Mono Movie Sports Action Game Roleplaying Game MUSIC Hall in Munich Hall in Vienna Chamber Cellar Club The Roxy Theatre The Bottom Line Music Video STEREO 2ch Stereo 5ch Stereo MUSIC ENHANCER Straight Enhancer 5ch Enhancer SUR. DECODE Sur.
RX-V367/HTR-3063 ■ INTERNAL VIEW 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 T F 16 12 13 16 11 10 14 9 OPERATION (3) P.C.B. MAIN (3) P.C.B. (R model) MAIN (1) P.C.B. AM/FM TUNER DIGITAL P.C.B. MAIN (2) P.C.B. OPERATION (4) P.C.B. MAIN (4) P.C.B. OPERATION (9) P.C.B. OPERATION (2) P.C.B. OPERATION (8) P.C.B. POWER TRANSFORMER OPERATION (7) P.C.B. OPERATION (1) P.C.B. OPERATION (6) P.C.B. OPERATION (5) P.C.B.
RX-V367/HTR-3063 ■ DISASSEMBLY PROCEDURES (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Top Cover a. Remove 5 screws (①) and 4 screws (②). (Fig. 1) b. Slide the top cover rearward to remove it. (Fig. 1) 2. Removal of Front Panel Unit a. b. c. d. Remove 7 screws (③). (Fig. 1) Remove CB166, CB193 and CB221. (Fig. 1) Unlock and remove CB136. (Fig. 1) Release hook and then remove the front panel unit. (Fig.
RX-V367/HTR-3063 3. Removal of DIGITAL P.C.B. a. Remove CB222–223 and CB262. (Fig. 2) b. Remove 2 screws (U, C models)/1 screw (R, T, K, A, B, G, L models) (④) and 5 screws (⑤). (Fig. 3) c. Remove the DIGITAL P.C.B. which is connected directly to the OPERATION (4) P.C.B. with board-to-board connectors. (Fig. 2) 4. Removal of OPERATION (4) P.C.B. a. Remove CB194. (Fig. 2) b. Remove screw (⑥) and 2 screws (⑦). (Fig. 3) c. Remove the OPERATION (4) P.C.B. which is connected directly to the MAIN (1) P.C.B.
RX-V367/HTR-3063 When checking the P.C.B. a. b. c. d. e. Remove the top cover. (Fig. 1) Remove 3 screws (⑧). (Fig. 3) Remove 5 screws (⑨) and 4 screws (⑩). (Fig. 4) Place the P.C.B.s (with rear panel) upright. (Fig. 5) Connect the ground of heat sink, rear panel and MAIN (1) P.C.B. (G3) to the chassis with a ground lead or the like. (Fig. 5) ⑨ ⑩ T F A R ⑨ RX-V367/HTR-3063 D ⑨ Fig. 4 Rear panel Ground lead G3 Chassis MAIN (1) P.C.B. Ground lead Heat sink Fig.
RX-V367/HTR-3063 ■ UPDATING FIRMWARE Note) Updating the firmware restores all the set up information (soundfield parameters, system memory and tuner presetting, etc.) to the original factory settings. When the following parts are replaced, the firmware must be updated to the latest version. DIGITAL P.C.B. Microprocessor (IC221, DIGITAL P.C.B.
RX-V367/HTR-3063 ● Connection Connect this unit and DVD/CD player as shown below. (Fig. 1) Example of connection between digital OPTICAL jacks This unit DVD/CD player Optical cable T F Example of connection between digital COAXIAL jacks A R This unit RX-V367/HTR-3063 D Digital audio pin cable Fig.
RX-V367/HTR-3063 ● Operation Procedures 1. While pressing the “INFO” key of this unit, connect the power cable of this unit to the AC outlet. (Fig. 2) The FIRMWARE UPDATE mode is activated and “CDDA Upgrader” is displayed. (Fig. 2) "INFO" key Display CDDA Upgrader T F Fig. 2 2. Eject the disc tray of the DVD/CD player, load the firmware CD on it and press the “PLAY” key. Writing of the firmware starts automatically. (Fig. 3) A R 3.
RX-V367/HTR-3063 ■ SELF-DIAGNOSTIC FUNCTION This unit has self-diagnostic functions that are intended for inspection, measurement and location of faulty point. There are 26 main menu items, each of which has sub-menu items. Listed in the table below are main menu items and sub-menu items. Note that not all menu items listed will apply to the models covered in this service manual. No.
RX-V367/HTR-3063 No.
RX-V367/HTR-3063 ● Starting Self-Diagnostic Function While pressing the “TONE CONTROL” and “STRAIGHT” keys of this unit as shown in the figure below, press the “ ” (Power) key of this unit to turn on the power. The self-diagnostic function mode is activated. Keys of this unit T F While pressing these keys, turn on the power.
RX-V367/HTR-3063 ● Display provided when Self-Diagnostic Function started The display is as described below depending on the situation when the last time the power to this unit is turned off. 1. When the power is turned off by usual operation: The FL display of this unit displays “NO PROTECT” then the main menu (sub-menu “1. ANALOG BYPAS” of main menu 1 BYPASS) a few seconds later. Opening message Main menu display After a few seconds NO PROTECT 1.ANALOG BYPAS 2.
RX-V367/HTR-3063 2-2. When the protection function worked due to a short between speaker terminals. I PROTECT:xxx AD value when the protection function is working Cause: The line between speaker terminals is shorted. Supplementary information: As the excess current is detected after operation of the speaker relay, the shorted speaker terminal and the connected speaker can be identified.
RX-V367/HTR-3063 2-5. When the protection function worked due to excessive heatsink temperature. THM PRT:xxx AD value when the protection function is working Cause: The temperature of the heatsink is excessive. Supplementary information: The protection function worked due to the temperature limit being exceeded. Causes could be poor ventilation or a defect related to the thermal sensor.
RX-V367/HTR-3063 ● Operation procedure of Main menu and Sub-menu There are 26 main menu items, each of having sub-menu items. Main menu selection Select the menu using “SCENE TV” (forward) and “SCENE BD/DVD” (reverse) keys. Sub-menu selection Select the sub-menu using “SCENE RADIO” (forward) and “SCENE CD” (reverse) keys.
RX-V367/HTR-3063 ● Details of Self-Diagnostic Function menu 1. BYPASS Using the sub-menu, it is possible to select ANALOG BYPASS output. 1-1. ANALOG BYPASS The analog input audio signal is output to FRONT L/R in DIRECT mode. 1.ANALOG BYPAS INPUT: AV5 ANALOG SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz SPEAKER OUTPUT Input level Both ch, -20 dBm FRONT CENTER SURROUND SUBWOOFER OUTPUT +11.5 dBm -∞ -∞ -∞ Volume +6.
RX-V367/HTR-3063 2. RAM THROUGH Using the sub-menu, it is possible to select MARGIN output or FULL BIT output. 2-1. RAM MARGIN The audio signal is output including the head margin. 2.RAM MARGIN INPUT: AV5 ANALOG SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz SPEAKER OUTPUT Input level Both ch, -20 dBm FRONT CENTER SURROUND SUBWOOFER OUTPUT +11.5 dBm +11.5 dBm +11.5 dBm -6.5 dBm Volume +6.5 dB T F 2-2.
RX-V367/HTR-3063 2-4. RAM FULL SURROUND The audio signal is output to only SURROUND L/R channels in digital full bit without including the head margin. 2.RAM FULL SUR INPUT: AV5 ANALOG SPEAKER OUT: 1 kHz, SUBWOOFER OUTPUT: 50 Hz SPEAKER OUTPUT Input level Both ch, -20 dBm FRONT CENTER SURROUND SUBWOOFER OUTPUT -∞ -∞ +11.5 dBm -∞ Volume +6.5 dB 2-5. RAM FULL SURROUND BACK Not for service. T F 2.
RX-V367/HTR-3063 3. HDMI AUDIO Using the sub-menu, the audio signals input to HDMI IN are selected and output. * When selecting “DSD”, be sure to connect an HDMI unit equipped with DSD output function to this unit. 3.SPDIF 3-1. SPDIF SPDIF signal is output. 3.Multi 3-2. Multi (DVD-Audio) Multi signal is output. 3.DSD 3-3. DSD (Direct stream digital) DSD signal is output. T F A R 4. SPEAKER SET D The analog switch settings for each sub-menu are as shown in the table below.
RX-V367/HTR-3063 4.FRNT:SML 0dB 4-1. FRONT: SML 0dB The FRONT L/R signal, when 90 Hz or lower, is mixed to the channel specified by LFE/BASS. 4.CENTER:NONE 4-2. CENTER: NONE The CENTER signal is distributed to FRONT L/R. 4.LFE/B:FRNT 4-3. LFE / BASS: FRONT The LFE/BASS signal is distributed to FRONT L/R. 4.TONE:MAX 4-4. TONE: MAX The audio signal is output with the tone control “BASS +10 dB”, “TREBLE +10 dB”. 4.TONE:MIN T F 4-5.
RX-V367/HTR-3063 5. LIMITER CONTROL Not for service. * When “5-3. LIM/PLDET/THM” sub-menu is selected, keys become non-operable. However, it is possible to advance to the next main menu by pressing the “SCENE TV” (forward) or “SCENE BD/DVD” (reverse) keys of this unit. 5.AC_B:Hi 5-1. AC-B: Hi 5.AC_B:Lo 5-2. AC-B: Lo 255255230000__ 5-3. LIM / PLDET / THM * Do not change the setting value because this item is only for the use of development staff. A R D 6.
RX-V367/HTR-3063 7. FL/MONITOR CHECK This menu is used to check the FL display and video monitor output. When checking the video monitor output, connect a TV monitor to this unit with a component video cable and video pin cable. Using the sub-menu, the FL display and video monitor output change together as shown below. Checking FL display section Check of the Video control section. (Monitor out) 7-1. INITIAL DISPLAY MONITOR output ON 7-2. ALL SEGMENT OFF MONITOR (VIDEO) output mute T F 7-3.
RX-V367/HTR-3063 8. MANUAL TEST The built-in noise generator of DSP outputs the test noise through the channels specified by using the sub-menu. The noise frequency for subwoofer is 30 to 80 Hz. Other than that, the noise frequency is 500 to 2 kHz. 8-1. TEST ALL Noise is output from all channels. 8.TEST ALL 9. A/D DATA CHECK T F This menu is used to display the A/D conversion value of the microprocessor which detects panel keys of this unit and protection functions in using the sub-menu.
RX-V367/HTR-3063 9-3. AMP/DK AMP: Power amplifier output is detected. Normal value: DK: 128 to 255 (Reference voltage: 3.3 V=255) DOCK type detection (U, C models) (Reference voltage: 3.3 V=255) AMP:255 DK:255 DOCK detection for AD port Pull-up resistance 10 k-ohms DOCK type (DKID 141 pin) Bluetooth iPod A/D value (3.3 V=255) 5 – 25 120 – 140 Wireless iPod No connected 255 T F 9-4. K1/K2 Panel key of this unit is detected.
RX-V367/HTR-3063 10. VIDEO CHECK This menu is used to check the video control section. 10-1. I2C check The I2C (Inter integrated circuit) bus line connection is checked. 0 : No error detected I2C: 00000000 1 : An error is detected 0 bit : – 1 bit : – 2 bit : – 3 bit : HDMI TRANSMITTER (IC202,DIGITAL P.C.B.) 4 bit : HDMI RECEIVER (IC201, DIGITAL P.C.B.) 5 bit : – 6 bit : – T F 7 bit : – 10-2. Digital component A R Not for service. DIGITAL COMP 10-3.
RX-V367/HTR-3063 11. NO MENU 11.Invalidity 12. NO MENU 12.Invalidity 13. NO MENU T F 13.
RX-V367/HTR-3063 14. DOCK 14-1. DOCK This menu is used to check the DOCK connector without the iPod itself. With the power to this unit turned off, short between pins No. 14 (TX) and No. 18 (RX), between pins No. 4 (iPDET) and No. 8 (DGND). Also, connect a 10 k-ohms, 1/4 W resistor between pins No. 21 (DKID) and No. 8 (DGND). (Make sure that the power is turned off.) Start up the self-diagnostic function and select this menu. The check result is displayed according to the following display specifications.
RX-V367/HTR-3063 15. HDMI INFORMATION The HDMI informations are displayed. MN:RX-V367 15-1. HDMI model name The model name of this unit written in HDMI module is displayed. RX-V367/HTR-3063 15-2. HDMI product ID PI: 3145 The product ID of this unit written in HDMI module is displayed. RX-V367: 3145 HTR-3063: 3146 VN: YAMAHA T F 15-3. HDMI vendor name The vendor name “YAMAHA” of this unit written in HDMI module is displayed. 16.
RX-V367/HTR-3063 17. NO MENU 17.Invalidity 18. IF STATUS (Input function status) Not for service. DST:710E0F2390 T F 19. BUS CHECK Communication and bus line connection between devices on the DIGITAL P.C.B. are checked. 19-1. TI (DSP) BUS check A R Communication and bus line connection between microprocessor (IC221) and TI (DSP, IC241) are checked. TI BUS:NoEr No error detected.
RX-V367/HTR-3063 21. PROTECTION HISTORY This menu is used to display the history of protection function. All history of protection function will be erased by pressing the “STRAIGHT” key. Example 21-1.PS1 078L 21-1. History 1 H: When the upper limit of the protection function is exceeded. L: When the lower limit of the protection function is exceeded. A/D value when the protection function is activated. (Reference voltage: 3.3 V=255) Example 21-2.NoPRT 21-2. History 2 T F Example 21-3.
RX-V367/HTR-3063 22. SOFT SWITCH When the following parts are replaced, the model name and the destination MUST be written to the back-up IC (EEPROM: IC222 of the DIGITAL P.C.B.) to have proper operation. • EEPROM (IC222) of DIGITAL P.C.B. • DIGITAL P.C.B. Note) When the DIGITAL P.C.B. is replaced, the firmware also must be updated to the latest version. (See “UPDATING FIRMWARE”) 22-1. SWITCH MODE Press the “STRAIGHT” key to select the “22. SW: MODEL”.
RX-V367/HTR-3063 23. UPDATE TI Not for service. 23.UPDATE TI 24. FACTORY PRESET This menu is used to reserve/inhibit initialization of the back-up IC (EEPROM: IC222 of the DIGITAL P.C.B.). 24.PRESET INHI 24-1. PRESET INHIBIT (Initialization inhibited) T F Initialization of the back-up IC is not executed. Select this sub-menu to protect the values set by the user. 24.PRESET RSRV A R 24-2. PRESET RESERVED (Initialization reserved) Initialization of the back-up IC is reserved.
RX-V367/HTR-3063 25. ROM VER/SUM/PORT The firmware version, checksum values, model name and destination are displayed. The checksum is obtained by adding the data at every 8-bits for each program area and expressing the result as a 4-figure hexadecimal notation. * Numeric values in the figure are given as reference only. VER. A017 25-1. Firmware version The firmware version of microprocessor (IC221 DIGITAL P.C.B.) is displayed. Sum: 7740 25-2.
RX-V367/HTR-3063 ■ DISPLAY DATA ● V1001 : 18-MT-09GNK (OPERATION P.C.B.) 69 1 PATTERN AREA ● PIN CONNECTION Pin No. 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 Connection F2 NX NP NP P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Pin No.
RX-V367/HTR-3063 RX-V367/HTR-3063 ● ANODE CONNECTION 18G 17G 16G 15G 1G-14G P1 1a 1a 1a S5 1-1 P2 1h 1h 1h S7 2-1 P3 1j 1j 1j 1d 3-1 P4 1k 1k 1k 2d 4-1 P5 1b 1b 1b S2 5-1 P6 1f 1f 1f 1e 1-2 P7 1m 1m 1m 2e 2-2 P8 1g 1g 1g S3 3-2 P9 1c 1c 1c 1c 4-2 P10 1e 1e 1e 2c 5-2 P11 1r 1r 1r S4 1-3 P12 1p 1p 1p 1g 2-3 P13 1n 1n 1n 2g P14 1d 1d 1d 1f P15 2a 2a 2a 2f P16 2h 2h 2h 1b P17 2j 2j 2j 2b P18 2k 2k 2k 1a
RX-V367/HTR-3063 ■ IC DATA MUTE 51 DATA CLOCK DGND SUBR1 SUBL1 SBLCIN SBRCIN FRIN2 FLIN2 SRIN2 SLIN2 SWIN2 CIN2 SBRIN2 SBLIN2 SLCIN SRCIN SUBR2 SUBL2 AVCC R2A15220FP (MAIN P.C.B.
RX-V367/HTR-3063 RX-V367/HTR-3063 Pin No.
RX-V367/HTR-3063 Pin No.
RX-V367/HTR-3063 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 SPI0_CLK/I2C0_SCL SPI0_SCS/I2C1_SCL Vss SPI0_ENA/I2C1_SDA EM_OE DVDD EM_RW CVDD EM_CS[2] Vss EM_RAS EM_CS[0] EM_BA[0] Vss EM_BA[1] EM_A[10] DVDD EM_A[0] CVDD EM_A[1] EM_A[2] Vss EM_A[3] CVDD EM_A[4] EM_A[5] Vss DVDD EM_A[6] EM_A[7] Vss CVDD EM_A[8] EM_A[9] EM_A[11] DVDD IC241: D70YE101BRFP266 (DIGITAL P.C.B.) Decoder/Post processor * No replacement part available.
RX-V367/HTR-3063 Function Name (P.C.B.) No.
RX-V367/HTR-3063 Function Name (P.C.B.) RX-V367/HTR-3063 No.
RX-V367/HTR-3063 Function Name (P.C.B.) TYPE(1) PULL(2) GPIO(3) O – N Asynchronous memory read/not write 104 EM_OE O – N SDRAM output enable 105 SPI0_ENA/I2C1_SDA IO – Y SPI0 enable (ready) or I2c1 serial data 107 SPI0_ENA/I2C1_SCL IO – Y SPI0 enable (ready) or I2c1 serial clock 108 SPI0_CLK/I2C0_SCL IO – Y SPI0 serial clock or I2c0 serial clock No.
RX-V367/HTR-3063 IC221: R5F364AMNBF (DIGITAL P.C.B.
RX-V367/HTR-3063 Pin No. Port Name Function Name (P.C.B.) Detail of Function RDS READY input / Open drain output (Imax=8 mZ) on LC72725 side O Low Fix O Low Fix O Low Fix IO Low Fix MCU MCU MCU MCU E8A_CNVSS MCU MCU MCU MCU VOL_RB VOL_RA N_CPU_RST XOUT DGND XIN +3.
RX-V367/HTR-3063 RX-V367/HTR-3063 Pin No. 60 Port Name Function Name (P.C.B.
RX-V367/HTR-3063 Pin No. Port Name Function Name (P.C.B.
RX-V367/HTR-3063 Pin No. Function Name (P.C.B.
A B C D E F G H I J RX-V367/HTR-3063 1 ■ BLOCK DIAGRAM DIGITAL r 4FF QBHF → SCHEMATIC DIAGRAM I2C2 29-32 HDMI IN 1 Port0 33-36 HDMI IN 2 2 21 22 107 IC201 Port1 N_HRX_RST HDM_INT HDM_MUT 25 N_HTX_RST IC202 Digital Video Data HDMI RX 37-40 HDMI IN 3 Port2 HDMI OUT HDMI Tx SiI9233 SiI9134 I2S 41-44 HDMI IN 4 Port3 I2S SPDIF 4 5 HDMI SPDIF XL201 27MHz MAIN (Component) IC41 (Optical) 2,4 AV2 N_CPNT_PS IC42 (Composite) Composite Selector TC74HC4051 (Composit
A B C D E F G H I J RX-V367/HTR-3063 ■ PRINTED CIRCUIT BOARDS 1 POINT A XL201 (Pin 5 of IC201) POINT C 1 / IC221 (97 pin, +3.3M), 2 / IC221 (10 pin, N_RESET) POINT B XL221 (Pin 11 of IC221) POINT D XL261 (Pin 29 of IC261) DIGITAL P.C.B. (Side A) 2 No replacement part available. DOCK HDMI 1 (BD/DVD) HDMI OUT D IC221 2 (N_RESET) IC221 2 (N_RESET) AC POWER ON (Connect the power cable) HDMI 2 HDMI 3 CB202 CB201 CB205 3 IC221 1 (+3.3M) No replacement part available.
A B C D E F G H I J RX-V367/HTR-3063 1 DIGITAL P.C.B. (Side B) 2 U, C models 3 A R 4 D T F 5 • Semiconductor Location 1 27 4 IC266 5 4 IC203 1 IC242 28 4 54 3 1 3 3 IC268 5 6 B, G, F models 5 1 Ref no.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (1) P.C.B. (Side A) 2 DIGITAL (CB221) OPERATION (7) (CB171) CB104 SW116 A R SW113 TUNING OPERATION (4) (CB193) CB106 4 MG VRB VRA +3.3S D OPERATION (6) SW111 SW109 AM FM T F SW107 CB102 AXR E AXL VE AUX-V +12 MIC E -12 CB103 CB101 3 DGND N_MIC_DET VOL_RB VOL_RA REM_IN PSW_DET N_FLD_RST FLD_SCK FLD_MOSI N_FLD_CS KEY2 KEY1 +3.3S DGND +3.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (1) P.C.B. (Side B) 2 33 32 D 10 1 A R 4 T F IC 48 49 3 17 16 64 1 5 6 • Semiconductor Location 7 Ref no. Location Ref no.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (2) P.C.B. (Side A) U, C models C model OUT COM IN IC132 OUT COM IN IC135 OUT COM IN IC133 OUT COM IN IC134 4 1 IC131 2 U, C models 13 6 CB AC6 VP AC6 OPERATION (1) (CB102) CB131 4 POWER TRANSFORMER -VP PS_PRT -12A AGND +12A NC AC5 AC5 AC4 AC4 AC3 AC3 AC2 E AC2 3 MG ACDET PRY S9 T F N_PDET PWR_RY N_CPU_RST +3.3M MG 9T AG +5A +5I IGND +7D DGND THM1_PRT THM2_PRT A R CB132 DIGITAL (CB262) D MAIN (1) (CB2) OPERATION (3) P.C.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (2) P.C.B. (Side B) U, C models R, T, K, A, B, G, L models 2 U, C models 3 A R 4 D 5 6 T F U, C models OPERATION (3) P.C.B. (Side B) • Semiconductor Location Ref no.
7 70 5VSEL_3 IPV AUXV +5A 5VSEL_1 DIGITAL (CB263) N_VO_MT IPVE AUXE -12A 5VSEL_2 +5D AV1_D AV2_D DG AV3_D AV4_D DG AGND ADL ADR IPE IPR IPL AGND MIC AGND AUXR AUXL AUXE DAFL DAFR AGND DAC DASW AGND DASL DASR AGND (DASBL) (DASBR) AGND F_MT C_MT S_MT +12A -12A D CB196 E MAIN (1) (CB21) CB194 F CB192 CB191 4 A R D CB195 DIGITAL (CB264) G (Side A) T F AGND +12V VAUXE AUXE -12V MIC +3.3S VRA VRB MG MAIN (2) OPERATION (1) (CB41) (CB106) CB145 AG CPNT_N_PS OPERATION (4) P.C.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (4) P.C.B. (Side B) OPERATION (5) P.C.B. (Side B) OPERATION (6) P.C.B. (Side B) 2 3 A R 4 D T F 5 6 • Semiconductor Location 7 Ref no.
A B C D E F G H I RX-V367/HTR-3063 1 OPERATION (7) P.C.B. OPERATION (8) P.C.B. (Side A) R, K, A, B, G, L models FG PSW MG N_MIC_DET -12 E MIC +12 3 CB171 2 OPERATION (1) (CB103) JK171 SW171 YPAO MIC A R 4 OPERATION (9) P.C.B.
A B C D E F G H I J RX-V367/HTR-3063 1 OPERATION (7) P.C.B. OPERATION (8) P.C.B. (Side B) (Side B) R, K, A, B, G, L models 2 4 6 IC102 1 5 3 A R 4 OPERATION (9) P.C.B. (Side B) D T F • Semiconductor Location Ref no.
A B C D E F G H I J RX-V367/HTR-3063 1 SPEAKERS R +/- MAIN (1) P.C.B.
A B C D E F G H I J RX-V367/HTR-3063 1 MAIN (1) P.C.B. (Side B) 2 1 7 IC22 8 3 4 5 14 1 IC23 8 4 81 80 1 IC25 8 100 1 21 5 IC 4 5 A R 51 50 1 IC24 8 30 31 4 5 8 IC27 1 4 D T F 5 • Semiconductor Location 6 7 Ref no. Location Ref no.
A B C D E F G H I J RX-V367/HTR-3063 1 MAIN (2) P.C.B. MAIN (3) P.C.B. (Side A) (Side A) R model 2 MONITOR OUT AV1 COMPONENT VIDEO PR/PB/Y COMPONENT VIDEO PR/PB/Y PJ41 AV2 AV3 AV 4 AV 5 AV OUT MONITOR OUT VIDEO PR/PB/Y PJ44 PJ43 PJ45 PJ42 SW51 3 CB41 A R 4 AG AG N_CPNT_MT 5V_SEL1 5V_SEL2 +5A -12A AUXV AUXE IPV IPVE 5V_SEL3 N_VO_MT OPERATION (4) (CB194) 5 6 7 76 MAIN (4) P.C.B. (Side A) D • Semiconductor Location Ref no.
A B C D E F G H I J RX-V367/HTR-3063 1 MAIN (2) P.C.B. MAIN (3) P.C.B. (Side B) (Side B) R model 2 16 3 9 36 IC42 24 13 1 19 IC43 8 1 1 12 A R 4 MAIN (4) P.C.B. (Side B) D T F 18 IC41 • Semiconductor Location Ref no.
RX-V367/HTR-3063 ■ PIN CONNECTION DIAGRAMS • ICs • Diodes BD9325FJ D70YE101BRFP266 SiI9233ACTU KIA7805API 108 KIA7812API KIA7912PI 1N4003S 1SS133 1SS176 1SS270A 73 72 109 1SS355 COM 144 OUT COM OUT IN LA73050-TLM-E OUT Anode LC89058WD-E – AC AC M12L64164A-5TG 24 16 25 12 36 1 1 1 37 54 28 1 27 RS203M-B-C-J80 MX29LV160DBTI-70G NJM2388F33 NJM2586AM (TE2) 24 25 D 12 17 1 48 16 1 1 4 NJM2830U1-05 (TE1) NJM2884U1-18 (TE1) 2 A R 48 33 64 NJM2867F3-05 NJM4565M
B A C D E F G H I J K L M N RX-V367/HTR-3063 SCHEMATIC DIAGRAMS DIGITAL 1/4 1 HDMI 4 HDMI 3 CB204 HDMI 2 CB203 HDMI 1 (BD/DVD) CB202 HDMI OUT CB201 CB205 2 0 0 0 0 3 0 0 0 0 0 0.6 0 0 0 0 0 0 0 0 0.6 0 0 0.6 0 0.6 IC204 IC204 IC204 IC204 4 4.9 5.1 T F 0 A 1.3 0 0 0 3.0 0 HDMI RX 0 1.3 3.6 3.4 0 3.4 0 2.2 0 2.2 3.4 0 2.2 0 2.2 0 2.2 IC201 3.3 3.4 3.3 1.9 0 0 0 1.9 0 0 0 0 0 1.9 0 0 0 0 1.9 4.9 0 0 1.
B A C D E F G H I J K L M N RX-V367/HTR-3063 DIGITAL 2/4 1 Page 85 CB222 3.4 3.4 0.3 0 9.0 0 0 0 0 0 3.0 0 -11.7 0 0 0 0.8 3.4 0 3.3 0 3.3 3.3 3.3 3.3 1.7 0 3.3 0 3.3 3.3 0 0 CB223 (B, G, F models) 3.4 3.4 3.4 3.3 3.4 3.4 3.4 3.4 0 CB221 3.4 To AM/FM TUNER to MAIN (1)_CB1 0 to OPERATION (1)_CB101 B2 3.3 C9 0 Page 83 2 RDS IC223 3 4 3.4 3.4 To DIGITAL 4/4 -11.7 3.4 3.4 5 3.4 3.4 0 3.4 0 0 0 0 0 3.4 3.3 0 3.3 3.4 0 3.
B A C D E F G H I J K L M N RX-V367/HTR-3063 DIGITAL 3/4 1 DIGITAL IN To DIGITAL 4/4 2 0.2 To DIGITAL 4/4 0.3 To DIGITAL 1/4 0 3.4 3.4 3.3 1.3 0 0 0 0 0 0 3.4 1.3 0 1.4 1.3 0 0 1.3 0 3.4 1.3 0 1.3 0 3.4 0 1.7 1.7 1.7 1.7 0 0 0 3 0 0 3.4 1.7 FL/FR C/SW 3.4 0 0 SL/SR 0 0 4 3.4 0 3.4 0 1.3 1.3 3.4 0 0 3.4 3.3 AUDIO DSP 0 0 0 0 3.3 3.4 0 0 0.3 0.5 3.4 3.4 1.7 IC246 1.3 0 0 A R 0 1.3 To DIGITAL 2/4 0 3.4 3.4 D 3.
B A C D E F G H I J K L M N RX-V367/HTR-3063 DIGITAL 4/4 1 IC261: LC89058WD-E Digital audio interface receiver No replacement part available. DOCK DIGITAL IN サービス部品供給なし MOUT 32 CB261 INT 35 AUDIO 33 41 XMODE Fs calculator GPIO0 GPIO1 GPIO2 GPIO3 44 45 46 47 Microprocessor I/F 40 39 38 37 Cbit, Pc CL CE DI DO 4.6 0 0 0 3.4 0 0 RX0 RX1 RX2 RX3 RX4 RX5 RX6 3.4 0 0 0 0 0 3.4 0 0 0 0 2 3.3 0 4.
B A C D E F G H I J K L M N RX-V367/HTR-3063 OPERATION 1/2 -29.1 -29.1 -31.8 -34.0 -31.9 -34.0 -31.9 -34.0 -36.2 -36.2 -34.0 -34.0 -31.9 -34.0 -34.0 -34.0 -34.0 -34.0 -36.2 -36.2 -36.0 -31.9 -31.8 -36.2 -34.0 -34.0 -29.8 -31.9 -34.0 -36.2 -38.3 -34.0 -34.0 -36.0 -34.0 -36.2 -36.2 -38.3 -36.1 -36.1 -36.1 -36.2 -36.1 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -36.2 -29.1 -29.1 1 2 OPERATION (5) -34.0 3.
B A C D E F G H I J K L M N RX-V367/HTR-3063 OPERATION 2/2 1 Page 83 J9 to OPERATION (1)_CB104 CB191 0 0 0 0 0 -11.8 2 Page 86 0 12.1 -11.8 0 CB193 F1 to MAIN (1)_CB22 5.1 12.1 -11.7 -11.7 -11.7 -11.7 -11.7 -11.7 0 0 0 0 0 0 2.5 0 2.5 2.5 2.5 2.5 SURROUND L SUBWOOFER CENTER Page 82 L7 to DIGITAL_CB264 0 0 2.5 2.5 2.5 2.5 2.5 0 0 2.5 0 2.5 0 0 CB195 FRONT L 3 CB192 Page 86 0 0 E1 to MAIN (1)_CB21 0 0 0 3.3 0 0 0 0 0 5.
B A C D E F G H I J K L M N RX-V367/HTR-3063 MAIN 1/3 1 MAIN (1) 0 IC2 54.2 1.7 54.1 0 0 0 0 0 0 0 0.7 0 53.7 0 3.3 0 0 -54.2 52.8 3.3 -54.0 3.3 0 0 0 3.3 Page 80 F2 SPEAKERS 0 3.3 2 FRONT 0 0 FRONT L 53.8 3.4 0 0 to DIGITAL_CB222 0.8 0 0 0 0 IC1: STK433-330Y-E 3-channel AF power amplifier, stand-by circuit built-in 0 -11.
B A C D E F G H I J K L M N RX-V367/HTR-3063 MAIN 2/3 1 C4 Page 84 C2 CB22 to OPERATION (4)_CB191 2 MUTE 51 DGND SUBR1 SUBL1 SBLCIN SBRCIN FRIN2 FLIN2 SRIN2 SLIN2 SWIN2 CIN2 SBRIN2 SBLIN2 SLCIN SRCIN SUBR2 SUBL2 AVCC MAIN (1) CLOCK 12.1 -11.8 -11.7 -11.7 0 -11.7 0 0 2.5 0 0 2.5 2.5 0 2.5 2.5 0 2.5 0 0 0 0 0 0 0 0 0 0 0 8-channel electronic volume with 11 input selector and tone control 0.3 0 0 0.4 0.4 0.2 5.
B A C D E F G H I J K L M N RX-V367/HTR-3063 MAIN 3/3 1 Page 84 E5 MAIN (2) 0 0 0 0 0 0 5.1 0 -11.8 0 5.1 MONITOR OUT 0 2 0 CB41 to OPERATION (4)_CB194 COMPONENT VIDEO 3 IC41: NJM2586AM (TE2) Wide band 3-input 1-output 3-circuit video amplifier CH1 IN1 1 Bias SW 1 75 Driver 6dB Amp 75 Driver Cont1 2 Cont2 CH1 IN2 6dB Amp 24 CH1 OUT 23 PS 22 CH2 OUT 21 V+2 20 CH3 OUT Cont1 3 Bias SW 2 4 Cont1 CH1 IN3 75 Driver 6dB Amp 5 Bias 4 0 0 5.
RX-V367/HTR-3063 ■ REPLACEMENT PARTS LIST • ELECTRICAL COMPONENT PARTS WARNING ● Components having special characteristics are marked equal to those originally installed. and must be replaced with parts having specifications ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : CHIP ALUMI.
RX-V367/HTR-3063 P.C.B. DIGITAL Ref No. Part No.
RX-V367/HTR-3063 P.C.B. DIGITAL and P.C.B. OPERATION Ref No. Part No.
RX-V367/HTR-3063 P.C.B. OPERATION Ref No. Part No.
RX-V367/HTR-3063 P.C.B. MAIN Ref No. Part No.
RX-V367/HTR-3063 P.C.B. MAIN Ref No. Part No. R433 RY1-4 RY5 TE1 TE1 TE2 U201-202 HV753100 WJ122400 WE648700 WK560800 WK560900 WB214000 WH169900 WE774200 R.CAR.FP RELAY RELAY TERM.SP TERM.SP TERM.SP CN.PHOTO.R SCR.BND.HD Description Markets 1Ω 1/4W 981-2A-24DS-SP7 DC DH24D2-O-Q 4P MST-204V1-01 NC 4P MST-204V1-01 WC 6P PUSH MSP-115V2 1P GP1FAV51RK0F 3x10 MFZN2W3 UCRTA KBGFL Ref No. Part No.
RX-V367/HTR-3063 Carbon Resistors Value 1.0 Ω 1.8 Ω 2.2 Ω 3.3 Ω 4.7 Ω 5.6 Ω 10 Ω 15 Ω 22 Ω 27 Ω 33 Ω 39 Ω 47 Ω 56 Ω 68 Ω 75 Ω 82 Ω 91 Ω 100 Ω 110 Ω 120 Ω 150 Ω 160 Ω 180 Ω 200 Ω 220 Ω 270 Ω 330 Ω 390 Ω 430 Ω 470 Ω 510 Ω 560 Ω 680 Ω 820 Ω 910 Ω 1.0 kΩ 1.2 kΩ 1.5 kΩ 1.8 kΩ 2.0 kΩ 2.2 kΩ 2.4 kΩ 2.7 kΩ 3.0 kΩ 3.3 kΩ 3.6 kΩ 3.9 kΩ 4.7 kΩ 5.1 kΩ 5.6 kΩ 6.8 kΩ 8.2 kΩ 9.1 kΩ 10 kΩ 1/4W Type Part No. 1/6W Type Part No.
A B C D E F G H I J RX-V367/HTR-3063 1 16 • OVERALL ASS'Y 203 L model 200 17 156 103 160 160 157 165 200-1 2 R model 204 160 103 101 165 12 160 20 202 U, C, R, T, L models 2-1 (3) ? 167 205 160 7 3 171 202 K, A, B, G, F models 206 T model A R 4 D 1-1 (7) 170 1-25 1-1 (5) 1-25 163 1-25 5 T F 1-1 (2) 2-104 2-104 22 2-1 (2) 168 171 170 15 168 21 168 1-1 (4) 1-1 (3) 167 167 2-104 167 168 1-1 (1) 2-103 1-25 1-7 1-5 (2) 1-2 1-6 2-104 109 151 2-1 (1)
RX-V367/HTR-3063 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Ref No. 1-1 1-1 1-1 1-1 1-1 1-2 1-3 1-4 1-4 1-4 1-4 1-4 1-4 1-4 1-4 1-4 1-4 1-5 1-5 1-5 1-5 1-6 1-7 1-12 1-25 2-1 2-1 2-1 2-103 2-104 7 7 7 12 12 15 15 15 15 15 16 16 16 16 16 16 16 17 20 21 22 101 101 101 101 103 103 103 103 103 ✻ New Parts Part No.
A B C D E F G H I J RX-V367/HTR-3063 ■ REMOTE CONTROL 1 ● RAV331: U, C models / RAV332: R, T, K, A, L models / RAV333: B, G, F models SCHEMATIC DIAGRAMS PANELS RAV331 (U, C models) RAV331, RAV332 VCC MODEL RAV331 RAV332 In-system programming point OPTION X X INPUT 78 R7 4.
RX-V367/HTR-3063 KEY NO. LAYOUT KEY CODE RAV331, RAV332 RAV331, RAV332 AMP MODE D2 1 SW2 2 4 3 5 8 6 9 12 16 GROUP 17 7 10 11 14 15 18 19 POWER PRE SET FUNCTION No.
RX-V367/HTR-3063 RAV331, RAV332 RAV331, RAV332 SOURCE MODE D2 1 SOURCE MODE 1 (INPUT1) SW2 2 3 Key FUNCTION No.
RX-V367/HTR-3063 RAV331, RAV332 RAV331, RAV332 SOURCE MODE D2 1 2 4 5 8 9 3 12 16 SOURCE MODE 1 (INPUT1) SW2 17 6 7 GROUP 10 11 VOLUME 14 15 18 19 Key FUNCTION No.
RX-V367/HTR-3063 KEY NO. LAYOUT KEY CODE RAV333 RAV333 CODE D2 Key No.
RX-V367/HTR-3063 ■ ADVANCED SETUP U, C models D A R T F 103
RX-V367/HTR-3063 R, T, K, A, B, G, F, L models (R, T, K, A, L models) (R, T, K, A, L models) D (R, T, K, L models) 104 A R T F (B, G, F models)
RX-V367/HTR-3063 MEMO T F RX-V367/HTR-3063 D A R 105
RX-V367/HTR-3063 D A R T F