2009 WaveRunner FX SHO FX Cruiser SHO OWNER’S/OPERATOR’S MANUAL U.S.A. Edition Read this manual carefully before operating this watercraft.
UF1W11E0.book Page 1 Tuesday, May 27, 2008 8:50 AM Read this manual carefully before operating this watercraft. This manual should stay with the WaveRunner if it is sold.
UF1W11E0.book Page 1 Tuesday, May 27, 2008 8:50 AM Important manual information EJU30181 EJU30221 To the owner/operator Thank you for choosing a Yamaha watercraft. This owner’s/operator’s manual contains information you will need for proper operation, maintenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or maintenance of your watercraft, please consult a Yamaha dealer.
UF1W11E0.book Page 1 Tuesday, May 27, 2008 8:50 AM Table of contents General and important labels........... 1 Identification numbers .................... 1 Primary Identification (PRI-ID) number ........................................... 1 Hull Identification Number (HIN) ........ 1 Engine serial number ........................ 1 Emission control information .......... 2 Approval label of emission control certificate ........................................ 2 Manufactured date label ....................
UF1W11E0.book Page 2 Tuesday, May 27, 2008 8:50 AM Table of contents Stopping the watercraft ................... Beaching the watercraft ................... Docking the watercraft ..................... Reverse on waterways .................... Operating in weeded areas ............. 79 80 80 80 81 Post-operation care ...................... 81 Transporting ................................. 82 Maintenance and care..................... 83 Storage .........................................
UF1W11E0.book Page 1 Tuesday, May 27, 2008 8:50 AM General and important labels EJU30261 EJU30300 Identification numbers Record the Primary Identification (PRI-ID) number, Hull Identification Number (HIN), and engine serial number in the spaces provided for assistance when ordering genuine parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen. Hull Identification Number (HIN) The HIN is stamped on a plate attached to the aft deck.
UF1W11E0.book Page 2 Tuesday, May 27, 2008 8:50 AM General and important labels EJU30350 Emission control information This engine conforms to 2009 U.S. Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB) regulations for marine SI engines. This engine is certified to operate on regular unleaded gasoline. EJU30400 Approval label of emission control certificate This label is attached to the top of the cylinder head and to the inside of the engine compartment.
UF1W11E0.book Page 3 Tuesday, May 27, 2008 8:50 AM General and important labels EJU30430 Manufactured date label This label is attached to the top of the cylinder head. One Star - Low Emission The one-star label identifies engines that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine 2001 exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted twostroke engines. These engines are equivalent to the U.S.
UF1W11E0.book Page 4 Tuesday, May 27, 2008 8:50 AM General and important labels exhaust emission standards or the Sterndrive and Inboard marine engine 2003-2008 exhaust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low Emission engines. Four Stars - Super Ultra Low Emission The four-star label identifies engines that meet the Air Resources Board’s Sterndrive and Inboard marine engine 2009 exhaust emission standards.
UF1W11E0.book Page 5 Tuesday, May 27, 2008 8:50 AM General and important labels EJU30451 Important labels Read the following labels before operating this watercraft. If you need any additional information, contact a Yamaha dealer.
UF1W11E0.book Page 6 Tuesday, May 27, 2008 8:50 AM General and important labels EJU35911 Warning labels If any of these labels are damaged or missing, contact a Yamaha dealer for replacements.
UF1W11E0.
UF1W11E0.
UF1W11E0.book Page 9 Tuesday, May 27, 2008 8:50 AM General and important labels The following label indicates the correct direction to upright a capsized watercraft.
UF1W11E0.book Page 10 Tuesday, May 27, 2008 8:50 AM Safety information EJU30671 The safe use and operation of this watercraft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and expertise of the operator. Every operator should know the following requirements before riding the watercraft. ● Before operating the watercraft, read this owner’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all labels on the watercraft.
UF1W11E0.book Page 11 Tuesday, May 27, 2008 8:50 AM Safety information teristics of the watercraft before trying any difficult maneuvers. EJU30761 Cruising limitations ● Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others. ● Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. Do not follow directly behind watercraft or other boats.
UF1W11E0.book Page 12 Tuesday, May 27, 2008 8:50 AM Safety information ● ● ● ● kles, and other bones. Do not jump wakes or waves. Do not operate the watercraft in rough water, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of adverse weather. Take note of weather forecasts and the prevailing weather conditions before setting out on your watercraft.
UF1W11E0.book Page 13 Tuesday, May 27, 2008 8:50 AM Safety information EJU30812 Operation requirements ● ● All riders must wear a U.S. Coast Guard (USCG) approved personal flotation device (PFD) that is suitable for personal watercraft use. Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into the water or being near the jet thrust nozzle.
UF1W11E0.book Page 14 Tuesday, May 27, 2008 8:50 AM Safety information ● ● tercraft to avoid accidental starting or unauthorized use by children or others. The operator and passengers should always keep their feet on the floor of the footwell when the watercraft is in motion. Lifting your feet increases the chances of losing your balance, or hitting objects outside the watercraft with your feet. Do not give a ride to children if their feet cannot reach the floor of the footwell.
UF1W11E0.book Page 15 Tuesday, May 27, 2008 8:50 AM Safety information boating laws also require that the fire extinguisher be approved by the USCG. 15 EJU30830 Recommended equipment The following items should be carried on board your watercraft: ● Sound-signaling device You should carry a whistle or other soundsignaling device that can be used to signal other boats. See “Rules of the Road” for more information. ● Visual distress signals It is recommended that a U.S.
UF1W11E0.book Page 16 Tuesday, May 27, 2008 8:50 AM Safety information EJU36850 EJU30920 Hazard information ● ● Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area. Do not touch the hot muffler or engine during or immediately after engine operation; they can cause serious burns.
UF1W11E0.book Page 17 Tuesday, May 27, 2008 8:50 AM Safety information ● ● ● Reverse can be used to slow down or stop during slow-speed maneuvering, such as when docking. Once the engine is idling, shift into reverse and gradually increase engine speed. Make sure that there are no obstacles or people behind you before shifting into reverse. Keep away from the intake grate while the engine is on.
UF1W11E0.book Page 18 Tuesday, May 27, 2008 8:50 AM Safety information EJU30941 Water-skiing You can use the watercraft for water-skiing if it has the seating capacity to carry the operator, a rearward-facing spotter, and the waterskier when he or she is not skiing. The watercraft must also have a cleat designed to pull a ski rope; do not attach the rope to any other location. is required by law. Let the skier direct the operator’s control of speed and direction with hand signals.
UF1W11E0.book Page 19 Tuesday, May 27, 2008 8:50 AM Safety information watch the skier’s hand signals and condition. ● 1 Handgrip FX SHO ● ● 1 Handgrip FX Cruiser SHO 1 1 Handgrip ● ● Your control while pulling a water-skier is affected by the skier’s ability, as well as water and weather conditions. When preparing to pull a skier, operate the watercraft at the slowest possible speed 19 until the watercraft is well away from the skier and slack in the ski rope is taken up.
UF1W11E0.book Page 20 Tuesday, May 27, 2008 8:50 AM Safety information EJU30961 Rules of the Road Your Yamaha watercraft is legally considered a powerboat. Operation of the watercraft must be in accordance with the rules and regulations governing the waterway on which it is used. Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are operating your watercraft.
UF1W11E0.book Page 21 Tuesday, May 27, 2008 8:50 AM Safety information give-way vessels). Both you and the meeting vessel must alter course to avoid each other. provided the other vessel gives you the rightof-way as it should. Meeting If you are meeting another power-driven vessel head on, and are close enough to run the risk of collision, neither of you has the right-ofway. Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side.
UF1W11E0.book Page 22 Tuesday, May 27, 2008 8:50 AM Safety information Fishing vessel right-of-way All vessels fishing with nets, lines, or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fishing vessels have the right-of-way regardless of position. Fishing vessels cannot, however, impede the passage of other vessels in narrow channels.
UF1W11E0.book Page 23 Tuesday, May 27, 2008 8:50 AM Safety information They signify speed zones, restricted areas, danger areas, and general information. Remember, markings may vary by geographic location. Always consult local boating authorities before riding your watercraft in unfamiliar waters.
UF1W11E0.book Page 24 Tuesday, May 27, 2008 8:50 AM Safety information EJU30980 To get more boating safety information The Online Boating Safety Course: http://www.boatus.com/onlinecourse/ Be informed about boating safety. Additional publications and information can be obtained from many organizations, including the following. United States Coast Guard Consumer Affairs Staff (G-BC) Office of Boating, Public, and Consumer Affairs U.S. Coast Guard Headquarters Washington, D.C.
UF1W11E0.book Page 25 Tuesday, May 27, 2008 8:50 AM Safety information EJU30991 Enjoy your watercraft responsibly You share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy. Whenever and wherever you ride, think of yourself as the guest of those around you.
UF1W11E0.
UF1W11E0.
UF1W11E0.
UF1W11E0.
UF1W11E0.book Page 30 Tuesday, May 27, 2008 8:50 AM Features and functions EJU31021 Operation of controls and other functions sure that the seat is securely installed before operating the watercraft. EJU31041 Seats To remove the rear seat: Pull the rear seat latch up, and then pull the seat off. 1 Seat latch To install the rear seat: Insert the projections on the front of the seat into the stays on the deck, and then push the rear of the seat down to lock it in place.
UF1W11E0.book Page 31 Tuesday, May 27, 2008 8:50 AM Features and functions push the rear of the seat down to lock it in place. To close the hood, push down on the center of the hood until it latches securely. Make sure that the hood is securely closed before operating the watercraft. EJU36691 Fuel tank filler cap The fuel tank filler cap is located under the hood. To remove the fuel tank filler cap, open the hood, and then turn the cap counterclockwise.
UF1W11E0.book Page 32 Tuesday, May 27, 2008 8:50 AM Features and functions System” on page 39 for information on using the remote control transmitter.) ● ● ● ● The Yamaha Security System and low-RPM mode settings can only be selected using the remote control transmitter. Store the remote control transmitter carefully so it will not be lost. When operating the watercraft, store the transmitter in the transmitter holder provided in the watertight compartment.
UF1W11E0.book Page 33 Tuesday, May 27, 2008 8:50 AM Features and functions EJU31150 Engine stop switch Push the engine stop switch (red button) to stop the engine normally. is not running to prevent unauthorized use by children or others.
UF1W11E0.book Page 34 Tuesday, May 27, 2008 8:50 AM Features and functions ● ● ● Lock mode of the Yamaha Security System has been selected. (See page 40 for Yamaha Security System lock and unlock mode selection procedures.) Clip is removed from the engine shut-off switch. Throttle lever is squeezed. EJU31210 Throttle lever Squeeze the throttle lever to increase engine speed.
UF1W11E0.book Page 35 Tuesday, May 27, 2008 8:50 AM Features and functions for the cause. (See pages 50 and 101 for more information.) TIP: ● ● If the cooling water passages are dry, it will take about 60 seconds for the water to reach the outlets after the engine is started. Water discharge may not be constant at idle, therefore, open the throttle a little to check that water discharges properly.
UF1W11E0.book Page 36 Tuesday, May 27, 2008 8:50 AM Features and functions To adjust the tilt, pull the tilt lever up, and then move the handlebars up or down to the desired position. EJU31312 Quick Shift Trim System (QSTS) selector The QSTS selector is located at the left handlebar grip and is used to adjust the trim angle of the watercraft. Make sure that the tilt lever returns to its original position and that the handlebars are locked in place after adjusting them.
UF1W11E0.book Page 37 Tuesday, May 27, 2008 8:50 AM Features and functions There are 5 positions: 2 bow-down positions (a) and (b), neutral “N”, and 2 bow-up positions (c) and (d). To enhance particular types of performance, select bow down or bow up. EJU31330 To change the trim angle: (1) Reduce engine speed to less than 3000 r/min. (2) Squeeze the QSTS selector lock lever, and then turn the QSTS selector to the desired position.
UF1W11E0.book Page 38 Tuesday, May 27, 2008 8:50 AM Features and functions ahead acceleration when on plane and top speed are enhanced. In some conditions, however, the watercraft may tend to “porpoise” (hop in the water). If the watercraft is porpoising, select neutral or bow down. EJU31361 Handgrip The handgrip provides a handhold for boarding the watercraft and for a spotter when facing rearward. WARNING! Do not use the handgrip to lift the watercraft.
UF1W11E0.book Page 39 Tuesday, May 27, 2008 8:50 AM Features and functions The bow eye is used to attach a rope to the watercraft when transporting, mooring, or towing it in an emergency. could fall, which could result in severe injury. [EWJ00821] 1 1 Pull-up cleat 1 Bow eye EJU34880 Stern eyes The stern eyes are located at the stern of the watercraft. The stern eyes are used to attach a rope to the watercraft when transporting or mooring it.
UF1W11E0.book Page 40 Tuesday, May 27, 2008 8:50 AM Features and functions (See page 31 for information on using the remote control transmitter.) Depending on the selected Yamaha Security System setting, the “UNLOCK” indicator light will come on or go off. 1 Remote control transmitter EJU36771 Yamaha Security System settings The Yamaha Security System settings are selected by pressing the lock or unlock button on the remote control transmitter briefly.
UF1W11E0.book Page 41 Tuesday, May 27, 2008 8:50 AM Features and functions unlock mode is selected and the engine can be started. TIP: The beeper sounds two times for the normal mode or three times for the low-RPM mode. (See the items in “Selecting the operation mode” for operation mode information.
UF1W11E0.book Page 42 Tuesday, May 27, 2008 8:50 AM Features and functions To activate the no-wake mode: TIP: TIP: The digital speedometer display flashes continually while the no-wake mode is activated. The no-wake mode cannot be activated immediately after starting the engine. After starting the engine, wait for 5 seconds or more before activating the mode. (1) Release the throttle lever. (2) Check that the shift lever is in the forward position.
UF1W11E0.book Page 43 Tuesday, May 27, 2008 8:50 AM Features and functions Activating and deactivating the cruise assist Activation of the cruise assist will be confirmed by the beeper and the digital speedometer display.
UF1W11E0.book Page 44 Tuesday, May 27, 2008 8:50 AM Features and functions and the engine will respond normally to the throttle. 1 2 engine speed will change. However, the adjustment is limited to a maximum of five increments above or below the initial cruise assist setting. To deactivate the cruise assist: Relax your grip on the throttle lever. The beeper sounds two times quickly and the digital speedometer display stops flashing when the cruise assist is deactivated.
UF1W11E0.book Page 45 Tuesday, May 27, 2008 8:50 AM Features and functions ponents for help and convenience in operating the watercraft. 1 Analog speedometer/tachometer and indicator lights 2 Left multifunction display and operation buttons 3 Right multifunction display and operation buttons (for FX Cruiser SHO) When the multifunction information center starts operating, the analog speedometer/tachometer makes one sweep, all displays light up for 2 seconds, and then the meter starts to operate normally.
UF1W11E0.book Page 46 Tuesday, May 27, 2008 8:50 AM Features and functions “RPM” indicator light comes on when the analog tachometer is selected. 1 “Speed/RPM” button 2 “SPEED” indicator light 3 “RPM” indicator light The “SPEED” indicator light blinks three times, then comes on, if miles are selected as the display units when the analog speedometer/tachometer is switched to the speedometer function. Analog speedometer The analog speedometer shows the watercraft speed against water.
UF1W11E0.book Page 47 Tuesday, May 27, 2008 8:50 AM Features and functions EJU34980 EJU35010 “WARNING” indicator light The “WARNING” indicator light blinks or comes on, together with a warning indicator, when a malfunction has occurred. “L-MODE” indicator light The “L-MODE” indicator light comes on when the low-RPM mode is selected. (See page 41 for more information.
UF1W11E0.book Page 48 Tuesday, May 27, 2008 8:50 AM Features and functions The following operation buttons are on the left side of the multifunction information center. 1 “Speed/RPM” button 2 “Volt/Hour” button TIP: Kilometers are selected as the display units at the Yamaha factory. 1 “Volt/Hour” button EJU37081 Digital speedometer The digital speedometer shows the watercraft speed against water.
UF1W11E0.book Page 49 Tuesday, May 27, 2008 8:50 AM Features and functions level meter disappear two at a time as the fuel level decreases. 1 1 Fuel level meter TIP: The fuel level is most accurate when the watercraft is sitting level on a trailer or in the water. EJU35061 Hour meter/voltmeter To switch the display between the hour meter and the voltmeter, push the “Volt/Hour” button for at least 1 second after the meter is displayed for more than 10 seconds.
UF1W11E0.book Page 50 Tuesday, May 27, 2008 8:50 AM Features and functions pressure warning indicator begin to blink, and the buzzer sounds intermittently. At the same time, the engine speed is limited to help prevent damage. If this occurs, reduce the engine speed, return to shore, and then check the engine oil level. (See page 61 for engine oil level checking procedures.) If the oil level is low, add enough engine oil to raise it to the proper level.
UF1W11E0.book Page 51 Tuesday, May 27, 2008 8:50 AM Features and functions check engine warning indicator begin to blink, and the buzzer sounds intermittently. If this occurs, reduce the engine speed, return to shore, and have a Yamaha dealer check the engine. TIP: Press any button on the multifunction information center to stop the buzzer. EJU35034 Right multifunction display and operation buttons (for FX Cruiser SHO) The right multifunction display shows the following information.
UF1W11E0.book Page 52 Tuesday, May 27, 2008 8:50 AM Features and functions the display units are switched to miles/gallons/degrees Fahrenheit. Average speed This display shows the average speed in miles per hour “AV MPH” or kilometers per hour “AV KMH” since it was reset. 1 “Volt/Hour” button 2 “SPEED” indicator light Compass This display shows the current direction of the watercraft using the 8 major compass points.
UF1W11E0.book Page 53 Tuesday, May 27, 2008 8:50 AM Features and functions Fuel consumption per hour This display shows the current fuel consumption in gallons per hour “G/HR” or liters per hour “L/HR”. Fuel consumption per kilometer/mile This display shows the current fuel consumption in gallons per mile “G/MILE” or liters per kilometer “L/KM”. TIP: The actual fuel consumption varies depending on the operating conditions. Use this function as a reference only.
UF1W11E0.book Page 54 Tuesday, May 27, 2008 8:50 AM Features and functions surements are stopped. The beeper sounds twice. To open the front storage compartment, pull the visor up, and then lift up the hood. 1 1 “Mode/Reset” button 2 “Start/Stop” button 1 Visor The displays can be reset only when the measurements are stopped. The measurements are not saved if the engine is stopped. The displays are reset automatically when they go off 25 seconds after the engine stops.
UF1W11E0.book Page 55 Tuesday, May 27, 2008 8:50 AM Features and functions To close the front storage compartment, push down on the center of the hood until it latches securely. Glove compartment: Capacity: 5.9 L (1.6 US gal, 1.3 Imp.gal) Load limit: 1.0 kg (2 lb) To close the glove compartment, lower the lid, and then turn the glove compartment knob to lock the lid in place. EJU31760 EJU35161 Glove compartment The glove compartment is located in front of the seat.
UF1W11E0.book Page 56 Tuesday, May 27, 2008 8:50 AM Features and functions EJU35171 Beverage holder The beverage holder is located on the starboard (right) side of the watercraft. 1 1 Beverage holder Do not place beverages in the beverage holder when operating the watercraft. EJU35184 Watertight compartment The watertight compartment is located on the port (left) side of the watercraft. To open the watertight compartment, turn the cap counterclockwise.
UF1W11E0.book Page 57 Tuesday, May 27, 2008 8:50 AM Operation EJU31821 Fuel and oil EJU37222 Fuel EWJ00282 WARNING ● ● Gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. Gasoline is poisonous and can cause injury or death. Handle gasoline with care. Never siphon gasoline by mouth.
UF1W11E0.book Page 58 Tuesday, May 27, 2008 8:50 AM Operation Make sure that the engine oil is at the specified level. Add oil as necessary. (See page 61 for engine oil level checking procedures.) Use a combination of the recommended SAE and API engine oil classifications shown in the chart below. Fuel tank capacity: 70 L (18.5 US gal, 15.4 Imp.gal) 1 1 Approximately 50 mm (2 in) from top of the fuel tank (6) Wipe up any spilled fuel immediately.
UF1W11E0.book Page 59 Tuesday, May 27, 2008 8:50 AM Operation EJU31980 Pre-operation checks EJU31991 Pre-operation check list Before operating this watercraft, perform the checks in the following check list. EWJ00411 WARNING Failure to inspect or maintain the watercraft properly increases the possibility of an accident or damage to the watercraft. Do not operate the watercraft if you find any problem.
UF1W11E0.book Page 60 Tuesday, May 27, 2008 8:50 AM Operation TIP: Pre-operation checks should be made each time the watercraft is used. These checks can be completed in a short time. It is worth the time spent to ensure safety and reliability.
UF1W11E0.book Page 61 Tuesday, May 27, 2008 8:50 AM Operation EJU32280 Pre-operation check points EJU32331 Engine compartment EWJ00460 WARNING Failure to ventilate the engine compartment could result in a fire or explosion. Do not start the engine if there is a fuel leak or a loose electrical connection. Ventilate the engine compartment before each use. To ventilate the engine compartment, remove the seats. (See page 30 for seat removal and installation procedures.
UF1W11E0.book Page 62 Tuesday, May 27, 2008 8:50 AM Operation tween the minimum and maximum level marks. (5) Remove the engine oil filler cap. 1 1 1 Engine oil filler cap 1 Dipstick 2 (6) Pour engine oil into the filler hole. Wait approximately 5 minutes until the engine oil settles.
UF1W11E0.book Page 63 Tuesday, May 27, 2008 8:50 AM Operation If water remains in the water separator, drain it by removing the drain screw. Place a drain pan under the water separator to catch the draining water or use a dry cloth to soak up any water that could spill into the watercraft. If any water spills into the watercraft, be sure to wipe it up with a dry cloth. Also, be sure to install the drain screw after draining the water separator. EJU32452 Bilge Check the bilge for moisture and fuel residue.
UF1W11E0.book Page 64 Tuesday, May 27, 2008 8:50 AM Operation Recharge the battery or replace it if it is not in good condition. (See page 95 for battery recharging procedures.) Also, check that the battery leads are tightened securely and that there is no corrosion on the battery terminals. Check that the breather hose is securely connected to the battery and that it is not pinched. WARNING! Fire or explosion could result if the breather hose is damaged, obstructed, or not connected properly.
UF1W11E0.book Page 65 Tuesday, May 27, 2008 8:50 AM Operation plete range and spring back to the idle position when released. EJU32611 Steering system Check the handlebars for looseness. Turn the handlebars as far as possible to the right and left to make sure that operation is smooth and unrestricted throughout the whole range. Also, make sure that the jet thrust nozzle moves as the handlebars are turned, and that there is no free play between the handlebars and the jet thrust nozzle.
UF1W11E0.book Page 66 Tuesday, May 27, 2008 8:50 AM Operation Also, make sure that the reverse gate goes up completely when the shift lever is pushed down. (2) Check that the QSTS selector turns smoothly when the lever is squeezed and check that the selector locks in place at each position when the lever is released. (3) Check that the angle of the jet thrust nozzle changes when the QSTS selector is shifted from neutral to bow up or bow down.
UF1W11E0.book Page 67 Tuesday, May 27, 2008 8:50 AM Operation EJU32651 Jet intake Carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the jet intake is clogged, clean it. (See page 101 for jet intake cleaning procedures.) If the watercraft is operated while the jet intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump.
UF1W11E0.book Page 68 Tuesday, May 27, 2008 8:50 AM Operation gine stop switch, and the engine shut-off switch.) 3 4 operation of the multifunction information center.) 1 5 2 1 2 3 4 5 Start switch Engine stop switch Engine shut-off switch Clip Engine shut-off cord (lanyard) EJU36890 Cooling water pilot outlets Check that water comes out from the port (left) cooling water pilot outlets while the engine is running and the watercraft is in the water. (See page 34 for more information.
UF1W11E0.book Page 69 Tuesday, May 27, 2008 8:50 AM Operation EJU32742 Operation EWJ00510 WARNING Before operating your watercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or function that you do not fully understand. Failure to understand how the controls work could cause an accident or prevent you from avoiding an accident. ECJ00460 NOTICE Make sure that the stern drain plugs are tightened securely before launching the watercraft.
UF1W11E0.book Page 70 Tuesday, May 27, 2008 8:50 AM Operation pebbles or sand could be sucked into the jet intake, causing impeller damage and engine overheating. [ECJ00471] (3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. It is not possible to start the engine with the clip removed from the engine shut-off switch. WARNING! Check that the engine shut-off cord (lanyard) is attached correctly.
UF1W11E0.book Page 71 Tuesday, May 27, 2008 8:50 AM Operation EJU37181 Shifting (2) Push the shift lever away from you. EWJ01230 WARNING ● ● ● Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars. Make sure that there are no obstacles or people behind you before shifting into reverse. Do not touch the reverse gate while the shift lever is being operated, otherwise you could be pinched.
UF1W11E0.book Page 72 Tuesday, May 27, 2008 8:50 AM Operation EJU32901 Operating your watercraft EJU32952 Getting to know your watercraft Operating your watercraft requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneuvers. Operating your new watercraft can be a very enjoyable activity, providing you with hours of pleasure.
UF1W11E0.book Page 73 Tuesday, May 27, 2008 8:50 AM Operation fabrics, like those used in bicycle shorts. A full wetsuit can also protect against hypothermia (subnormal body temperature) and abrasions. Footwear and gloves are recommended. Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your watercraft. Restraining straps for eyewear are made which are designed to float should your eyewear fall in the water.
UF1W11E0.book Page 74 Tuesday, May 27, 2008 8:50 AM Operation throttle lever when trying to steer away from objects—you need throttle to steer. start the engine, and then look in all directions before starting off. EJU33111 Boarding and starting from a dock (1) Board the watercraft from the side. (2) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.
UF1W11E0.book Page 75 Tuesday, May 27, 2008 8:50 AM Operation EJU36351 Boarding alone (1) Swim to the rear of the watercraft and place both hands on the boarding platform, pull yourself up, and then grasp the handgrip with one hand. start the engine, and then look in all directions before starting off. TIP: (2) Pull yourself up to a kneeling position on the platform, and then move to the seat and sit astride.
UF1W11E0.book Page 76 Tuesday, May 27, 2008 8:50 AM Operation (1) Climb on board as noted in the previous section, and sit astride the seat. both the passengers and the operator should try to balance the watercraft. (2) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (3) Have the passengers move to the rear of the watercraft.
UF1W11E0.book Page 77 Tuesday, May 27, 2008 8:50 AM Operation tion, and then move to the seat and sit astride to balance the watercraft. (2) Have a passenger pull him or herself up onto the boarding platform into a kneeling position, then move to the seat and sit astride to balance the watercraft. (3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (4) Start the engine and keep it at idle.
UF1W11E0.book Page 78 Tuesday, May 27, 2008 8:50 AM Operation which can result in severe damage. [ECJ00541] ● (3) Start the engine and operate the watercraft as straight as possible and above planing speed for at least 2 minutes to discharge any water remaining in the engine compartment. (If the engine does not start, see “Towing the watercraft” on page 104 or “Submerged watercraft” on page 104.) NOTICE: Do not operate the engine at full throttle for at least 1 minute after the engine has been restarted.
UF1W11E0.book Page 79 Tuesday, May 27, 2008 8:50 AM Operation B. Less throttle produces lower thrust, so the watercraft will turn more gradually. C. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle.
UF1W11E0.book Page 80 Tuesday, May 27, 2008 8:50 AM Operation soon as the throttle lever is released, but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction. (2) Approach the beach slowly and stop the engine before reaching land. Remember, you need throttle to steer. (3) Get off the watercraft and pull it up on the beach.
UF1W11E0.book Page 81 Tuesday, May 27, 2008 8:50 AM Operation EJU37190 EJU37141 Post-operation care Operating in weeded areas Always avoid operating your watercraft in areas where weed growth is thick. If traveling in weeded areas is unavoidable, operate the engine alternately at partial throttle and full throttle. Weeds tend to accumulate more at a steady speed and at trolling speed. If weeds clog the intake area and cause cavitation, clean the jet intake and impeller.
UF1W11E0.book Page 82 Tuesday, May 27, 2008 8:50 AM Operation (5) Flush the cooling system to prevent it from clogging with salt, sand, or dirt. (See page 83 for flushing procedures.) (6) Rinse the engine and engine compartment with a small amount of water. NOTICE: Do not use high-pressure water when rinsing the engine or engine compartment as severe engine damage could result. [ECJ00571] (7) Wipe the engine and engine compartment dry with a clean cloth (repeat step 3, if necessary).
UF1W11E0.book Page 83 Thursday, June 12, 2008 4:23 PM Maintenance and care (4) Connect the garden hose adapter to a water tap using a garden hose. EJU33490 Storage EWJ00330 TIP: WARNING Always place the watercraft upright in a horizontal position when storing it, otherwise fuel could leak out into the engine or engine compartment, which could create a fire hazard. Storage for long periods of time, such as winter storage, requires preventive maintenance to ensure against deterioration.
UF1W11E0.book Page 84 Thursday, June 12, 2008 4:23 PM Maintenance and care water passages by alternately squeezing and releasing the throttle lever for 10 to 15 seconds. (8) Stop the engine. (9) Remove the garden hose adapter and install the flushing hose connector cap. (10) Install the seat storage compartment and the rear seat. EJU36902 Lubrication (1) Lubricate all cables such as the throttle and steering cables.
UF1W11E0.book Page 85 Tuesday, May 27, 2008 8:50 AM Maintenance and care EJU33752 Maintenance and adjustments Periodic inspection, adjustment, and lubrication will keep your watercraft in the safest and most efficient condition possible. Safety is an obligation of the watercraft owner. Proper maintenance must be carried out to keep the exhaust emission and sound levels within the regulated limits.
UF1W11E0.book Page 86 Tuesday, May 27, 2008 8:50 AM Maintenance and care wrench may also be necessary to tighten nuts and bolts.
UF1W11E0.book Page 87 Tuesday, May 27, 2008 8:50 AM Maintenance and care EJU37060 Periodic maintenance chart The following chart gives general guidelines for periodic maintenance. However, maintenance may need to be performed more frequently depending on your operating conditions. This “ ” mark indicates maintenance that you may do yourself. This “ ” mark indicates work to be done by a Yamaha dealer.
UF1W11E0.book Page 88 Tuesday, May 27, 2008 8:50 AM Maintenance and care Initial Item Operation 10 hours 50 hours Thereafter every 100 hours 100 hours 200 hours Page 6 12 12 24 months months months months Battery Check, charge 95 Rubber coupling Check — Engine mount Check — Nuts and bolts Check — Air filter element Check 89 Engine oil Replace Oil filter Replace 89 Valve clearance Check, adjust — 50 hours or 12 months 89 *1 This operation should be performed after every use.
UF1W11E0.book Page 89 Tuesday, May 27, 2008 8:50 AM Maintenance and care EJU34212 EJU36941 Checking the fuel system Engine oil and oil filter EWJ00381 EWJ00340 WARNING WARNING Leaking fuel can result in fire or explosion. ● Check for fuel leakage regularly. ● If any fuel leakage is found, the fuel system must be repaired by a qualified mechanic. Improper repairs can make the watercraft unsafe to operate. Engine oil is extremely hot immediately after the engine is turned off.
UF1W11E0.book Page 90 Tuesday, May 27, 2008 8:50 AM Maintenance and care Difference of A and B: Maximum 5 mm (0.20 in) If the reverse gate does not make contact with the stopper, have a Yamaha dealer service it. EJU37030 Checking and adjusting the throttle cable Face the handlebars straight ahead, and then check that the throttle cable moves back to the set position smoothly and that the throttle lever free play is within specification. Squeeze and release the throttle lever.
UF1W11E0.book Page 91 Tuesday, May 27, 2008 8:50 AM Maintenance and care (3) Make sure that the handlebars are facing straight ahead, and then adjust the free play by turning the adjuster. 1 2 3 4 Rubber cover Locknut Adjuster Throttle lever free play Throttle lever free play: 2.0–5.0 mm (0.08–0.20 in) (4) Hold the adjuster with one wrench while tightening the locknut with another wrench. Slide the rubber cover to its original position.
UF1W11E0.book Page 92 Tuesday, May 27, 2008 8:50 AM Maintenance and care (5) Install the front and rear handlebar covers as shown in the illustration, and then install the ten screws. Remove and inspect the spark plugs periodically; heat and deposits will cause the spark plugs to slowly break down and erode. If electrode erosion becomes excessive, or if carbon and other deposits are excessive, replace the spark plug with the specified plug.
UF1W11E0.book Page 93 Tuesday, May 27, 2008 8:50 AM Maintenance and care TIP: If removing the spark plug cap nearest the stern, remove the plastic tie that is securing the wiring harness before removing the cap. 1 2 (3) Install the spark plug, and then tighten it to the specified torque. Spark plug tightening torque: 24.5 Nm (2.50 kgf-m, 18.1 ft-lb) TIP: 3 1 Spark plug cap bolt 2 Spark plug cap 3 Plastic tie (4) Remove the spark plug. Measure the spark plug gap with a wire thickness gauge.
UF1W11E0.book Page 94 Tuesday, May 27, 2008 8:50 AM Maintenance and care outer cable, and then adjust the throttle cable free play. (See page 90 for adjustment procedures.) ● Shift cable (shift lever end) ● Shift cable (reverse gate end) ● Intermediate housing Fill the intermediate housing with water-resistant grease through the grease nipple using a grease gun.
UF1W11E0.book Page 95 Tuesday, May 27, 2008 8:50 AM Maintenance and care Grease quantity: Initial 10 hours or 1 month: 33.0–35.0 cm³ (1.12–1.18 US oz, 1.16–1.23 Imp.oz) Every 100 hours or 12 months: 6.0–8.0 cm³ (0.20–0.27 US oz, 0.21–0.28 Imp.oz) tilated. Always shield your eyes when working near batteries. Keep out of the reach of children.
UF1W11E0.book Page 96 Tuesday, May 27, 2008 8:50 AM Maintenance and care To install the battery: (1) Place the battery in the battery compartment. Connect the red lead to the positive (+) battery terminal, and then connect the black lead to the negative (–) battery terminal. NOTICE: Reversal of the battery leads will damage the electrical parts. [ECJ00261] (2) Connect the breather hose to the battery. (3) Secure the battery in place.
UF1W11E0.book Page 97 Tuesday, May 27, 2008 8:50 AM Specifications EJU34542 Specifications Watercraft capacity: Maximum people on board: 3 person Maximum load capacity: 240 kg (530 lb) Dimensions: Length: 3370 mm (132.7 in) Width: 1230 mm (48.4 in) Height: FX SHO 1160 mm (45.7 in) FX Cruiser SHO 1240 mm (48.8 in) Dry weight: FX SHO 376 kg (829 lb) FX Cruiser SHO 381 kg (840 lb) Performance: Maximum fuel consumption: 71.3 L/h (18.8 US gal/h, 15.7 Imp.gal/h) Cruising range at full throttle: 0.
UF1W11E0.book Page 98 Tuesday, May 27, 2008 8:50 AM Trouble recovery EJU34560 Troubleshooting If you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
UF1W11E0.
UF1W11E0.
UF1W11E0.book Page 101 Tuesday, May 27, 2008 8:50 AM Trouble recovery EJU34620 Emergency procedures EJU34631 ways stop the engine before beaching the watercraft. Cleaning the jet intake and impeller EWJ00780 WARNING Before attempting to remove weeds or debris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch. Severe injury or death could result from coming in contact with the rotating parts of the jet pump.
UF1W11E0.book Page 102 Tuesday, May 27, 2008 8:50 AM Trouble recovery (2) Remove any weeds or debris from around the jet intake, drive shaft, impeller, jet pump housing, and jet thrust nozzle. If debris is difficult to remove, consult a Yamaha dealer. (3) Connect the other end of the negative (–) jumper cable to an engine hanger. 2 3 1 EJU34641 Jumping the battery If the watercraft battery has run down, the engine can be started using a 12-volt booster battery and jumper cables.
UF1W11E0.book Page 103 Tuesday, May 27, 2008 8:50 AM Trouble recovery system damage and possible fire. (2) Remove the electrical box cover. [EWJ00801] 1 1 3 4 2 1 Electrical box cover (3) Remove the cap on the electrical box. (4) Replace the blown fuse with the spare fuse of the correct amperage by using the fuse puller on the reverse side of the cap. WARNING! Do not use fuses of higher amperage than recommended.
UF1W11E0.book Page 104 Tuesday, May 27, 2008 8:50 AM Trouble recovery EJU34711 Towing the watercraft EWJ00811 WARNING ● ● The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a hazard to the operator on the watercraft. The towline should be long enough so that the watercraft will not collide with the towing boat when slowing down. If the watercraft becomes inoperative in the water, it can be towed to shore.
UF1W11E0.book Page 105 Tuesday, May 27, 2008 8:50 AM Consumer information EJU34780 Limited warranty YAMAHA MOTOR CORPORATION, U.S.A. WATERCRAFT LIMITED WARRANTY Yamaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to customer satisfaction. The Yamaha Watercraft Limited Warranty is your assurance of this commitment.
UF1W11E0.book Page 106 Tuesday, May 27, 2008 8:50 AM Consumer information THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. YAMAHA MOTOR CORPORATION, U.S.A. Post Office Box 6555 Cypress, California 90630 WARRANTY QUESTIONS AND ANSWERS Q. What costs are my responsibility during the warranty period? A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages. Q.
UF1W11E0.book Page 107 Tuesday, May 27, 2008 8:50 AM Consumer information EJU34800 YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.). • Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind. • Y.E.S. is flexible.
UF1W11E0.book Page 1 Tuesday, May 27, 2008 8:50 AM Index A Air filter element ....................................... 89 Analog speedometer/tachometer ............. 45 Analog speedometer/tachometer and indicator lights....................................... 45 Approval label of emission control certificate ................................................ 2 B Battery................................................ 63, 84 Battery, checking...................................... 95 Battery, jumping ...........
UF1W11E0.book Page 2 Tuesday, May 27, 2008 8:50 AM Index Lubrication................................................ 84 Lubrication points ..................................... 93 M Main components, location of .................. 26 Maintenance and adjustments ................. 85 Manufactured date label............................. 3 Multifunction information center ......... 44, 68 N No-wake mode ......................................... 41 “NO-WAKE MODE” switch.......................
UF1W11E0.book Page 3 Tuesday, May 27, 2008 8:50 AM Index YAMAHA EXTENDED SERVICE (Y.E.S.) ............................................... 107 Yamaha Security System......................... 39 Yamaha Security System settings ...........
A5-tate_Blank.
A5-tate_Blank.
YAMAHA MOTOR CORPORATION, USA Printed in USA June 2008–2.
