manual

ManualsBrandsYamaha ManualsMusical InstrumentsDTX750K

DTX750K Assembly Manual

This pamphlet describes the standard procedure for DTX750K assembly.

After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.

• For assembly, you will require four individual packages – an RS700

Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a

DTX700 Drum Trigger Module.

• This pamphlet describes how to attach the pads and drum trigger

module to the RS700 Rack System. Before carrying out the proce-

dures described below, ensure that you have correctly assembled

the rack system as described in its assembly manual.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, before setting up the HS650A Hi-hat Stand and KP65

Kick Pad, you can place the packages' cardboard boxes on the floor to

protect it from damage.

Before using, please read this assembly manual, and use this product in a safe and proper manner.

* Please keep this manual in a safe place for future reference.

* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

NOTICE

• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,

never place any heavy or sharp objects on the cable. Applying excessive force to the cable may

result in damage to the cable, such as the wires being severed, etc.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,

close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).

Doing so may result in deformation, discoloration, damage or deterioration.

• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or

deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the

product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has

been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to

let the water and detergent come into contact with the cushions used in the product; doing so may

result in deterioration.

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

PRECAUTIONS

Standard Assembly Example

PCY135

(Cymbal Pad)

PCY155

(Cymbal Pad)

CH750

(Cymbal Holder)

PCY135

(Cymbal Pad)

CH755

(Cymbal Holder)

XP80

(Tom Pad)

XP80

(Tom Pad)

KP65

(Kick Pad)

XP100SD

(Snare Pad)

SS662

(Snare Stand)

HS650A

(Hi-hat Stand)

DTX700 Drum

Trigger Module

RHH135

(Real Hi-hat Pad)

CH750

(Cymbal Holder)

RS700

(Rack System)

IMPORTANT

NOTICE

If this symbol is ignored and the equipment is used improperly,

fatal injury to persons or serious damage could occur.

• Do not let small children assemble or set up this product by themselves, or they may be injured.

Always assemble this product with adult supervision.

• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends

may result in injury.

• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends

may result in injury.

• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened

firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may

result in the rack overturning or parts dropping, causing injury.

• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on

steps may result in the product being unstable and subject to overturning.

• When setting up the product, please pay close attention to the handling and setting of cables.

Carelessly placed cables may cause the user and others to trip and fall.

• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

If this symbol is ignored and the equipment is used improperly,

there is a danger or injury to persons handling the equipment, and

material damage could occur.

• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your

fingers.

• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting

in injury.

• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums

may drop, causing injury.

Digital Musical Instruments DivisionDigital Musical Instruments Division

WW60710 110PO***.*01C0

WARNING

CAUTION

Assemble the RS700 Rack System.

For details, refer to the assembly manual that came with the rack system.

Check the contents of each package.

Mount the pads and the drum trigger module on the rack system.

As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.

 PCY135

Cymbal Pad (x2)

 PCY155

Cymbal Pad (x1)

 RHH135

Real Hi-hat Pad (x1)

Package 1: DTP750C

Package 2: DTP750P

Package 3: DTX700

 Stand base for the

RHH135 (x1)

 CH750

Cymbal Holder (x2)

 CH755

Cymbal Holder (x1)

 HS650A

Hi-hat Stand (x1)

 Hi-hat clutch for the

RHH135 (x1)

 Cable band for the

RHH135 (x1)

 Stoppers for the

PCY135 and

PCY155 (x3)

 Felts for the

PCY135 and

PCY155 (x3)

 10-channel snake cable (x1)

 PCY100, PCY135, and PCY155 Owner’s Manual (x1)

 RHH135 Owner’s Manual (x1)

 Assembly Manual (this pamphlet)

 Tuning key (x1)

 Cable bands (x10)

 DTX700 Owner’s Manual (x1)

 DTX700 Data List (x1)

 DVD (containing software)

 DTX700 Drum Trigger

Module (x1)

 AC power adaptor*

(x1)

 Module stand (x1)

 Module stand

fastening screws (x4)

 XP100SD

Snare Pad (x1)

 XP80

Tom Pad (x3)

 SS662

Snare Stand (x1)

 Clamp bolts (x4)

 Clamp bolt S (x1)

 KP65

Kick Pad (x1)

 XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1)

 XP70 and XP80 Owner’s Manual (x1)

 KP65 Owner’s Manual (x1)

* May not be included de-

pending on your particular

area. Please check with

your Yamaha dealer.

Mounting the cymbal holders

Mounting the tom pad

1. Mount the cymbal holders (CH750 x 2, CH755 x 1) on

the rack system as shown below.

CH750

CH755

1. Attach the clamp bolt to each of the tom pads

and provisionally tighten (by 5 or 6 turns).

2. Mount the tom pads on the rack’s clamp rods.

As shown below, ensure that the rod section

is fully inserted into each pad’s mounting hole,

and then fully tighten the clamp bolt.

3. If necessary, use clamp bolts A to E to adjust

the height and angle of any of the pads. When

doing so, be sure to adjust one bolt at a time

(i.e., loosen a bolt, adjust the pad, and then

retighten before loosening another).

XP80

Clamp bolt (to be tight-

ened in the direction

shown)

Tom pad (rear side)

Tom pad

Rod

section

Clamp bolt

Insert

Clamp rod

Clamp bolt B

Clamp bolt D

Clamp bolt E

Clamp bolt A

Clamp bolt C

Continued on other side

Summary of content (2 pages)

PAGE 1
Digital Musical Instruments Division ©2011 Yamaha Corporation WW60710 110PO***.*01C0 DTX750K Assembly Manual EN This pamphlet describes the standard procedure for DTX750K assembly. After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module. 1 2 Assemble the RS700 Rack System. For details, refer to the assembly manual that came with the rack system. Check the contents of each package.
PAGE 2
Mounting the drum trigger module and cymbal pads Assembling the kick pad 1.  Mounting the cymbal pads PCY135 PCY155 PCY135 1. Using a tuning key, loosen the stopper’s key bolt. 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using a tuning key. Stopper Drum trigger module Mounting the snare stand and pad 1. Open up the snare stand’s legs and stand it up on the floor. 2.