User Manual
1
Thank you for purchasing the Yamaha DTX482K! As a high-end model of the DTX402 series, the DTX482K comes standard
with three cymbal pads (two crashes and one ride) and the DTX-series XP80 Snare Pad. We recommend that you read this
manual carefully so that you can fully take advantage of the advanced and convenient functions of the instrument. We also
recommend that you keep this manual in a safe and handy place for future reference.
Before using this product, be sure to read the “PRECAUTIONS” on pages 4 to 5 on the DTX402K, DTX432K, and DTX452K Owner’s Manual.
NOTICE
Some objects made of rubber and similar materials can easily stain the drumhead of the snare pad. Do not leave such objects in contact with the drumhead for a long period of
time. Pay special attention to avoid stacking the pads when putting them in storage, for example.
1.
Package Content
After opening up the package containing your electronic drum kit, please verify that all of the following parts are present.
DTX482K Package Content
Rack (Small)Rack (Large)
Pipe for
TOM3
Rod for the snare pad
Drum module
Hi-hat holder Cymbal holders (×2)
Stopper
No Stopper
KP65
Kick pad
Cymbal/hi-hat pads (×2) Crash cymbal pad
Sensor (bumps)
HH65 Hi-hat controller
FP6110A
Foot pedal
Nine-channel snake cable Drum key Cable bands (×3) AC adaptor
* May not be included depending on your particular area.
Please check you’re your Yamaha dealer.
DTX482K Owner’s Manual (this booklet)
DTX402K, DTX432K, and DTX452K Owner’s Manual
KP65 Owner’s Manual
XP70, XP80 Owner’s Manual
Additional Cymbal pad XP80 Snare Pad
Cymbal pad (×1)
Cymbal holder (×1) Stopper (×1)
Stereo audio cable (×1)
XP80 main unit (×1) Clamp bolt (×1)
Attaching the cymbal holder for the additional cym-
bal pad.
1. Loosen the (
1,
2) key bolts and detach the pipe for TOM3.
2. Loosen the clamp bolt of the cymbal holder.
3. Slide the holder clamp onto the TOM3 pipe, and lightly tighten the
clamp bolt of the cymbal holder.
4. Attach the TOM3 pipe back to the large rack.
5. Tighten the key bolt (
in the above figure) on the large rack and the
clamp bolt of the cymbal holder.
w
2
q
e
1
r
Pipe for TOM3
Cymbal holder
Clamp bolt
Clamp bolt
Holder clamp
Pipe for TOM3
Turn the entire large rack over and continue with the
assembly by following the instructions on pages 13 and 14
of the DTX402K, DTX432K, and DTX452K Owner’s
Manual
Step 1
Step 2
Step 3
2.
Assembly Guide (1/2)
To assemble the DTX482K, refer to this Owner’s Manual and the DTX402K, DTX432K, and DTX452K Owner’s Manual
Fully Assembled DTX482K
CAUTION
• Choose a flat, hard surface on which to
assemble your electronic drum kit.
• Take care to avoid mixing up parts or assem-
bling them in the wrong direction. In addition,
the assembly steps should be completed one
at a time in the order described.
• The assistance of at least one other person
will be required when assembling the elec-
tronic drum kit.
• Once a piece has been assembled, be sure to
tighten the corresponding key bolts.
• To disassemble your electronic drum kit, carry
out the assembly sequence in reverse.
Step 8
Step 7
Step 6
Step 4
Step 3Step 2
Step 12
Step 9
Step 10
Step 5
Step 9
Step 1
Step 12Step 11
Additional cymbal pad
Continue to the other side.
Cable band position
ELECTRONIC DRUM KIT
DTX482K
Manual Development Group
© 2018 Yamaha Corporation
Published 08/2014 POMA*.*-**A0
VAU5550
Owner’s Manual
EN