DIGITAL MIXING ENGINE Owner’s Manual EN
Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device.
Connections Handling caution • Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Do not insert your fingers or hand in any gaps or openings on the device (vents, ports, etc.). • Be sure to connect to a properly grounded power source. A ground screw terminal is provided on the rear panel for safely grounding the device and preventing electrical shock.
Foreword Foreword Thank you for choosing a Yamaha DME64N/24N Digital Mixing Engine. Using the supplied DME Designer software, the DME64N and DME24N can be easily configured to handle a wide range of audio processing applications – institutional audio installations, sub-mixing, speaker system control, matrix and routing, multi-effect processing, and much more.
Contents Contents About the Documentation . . . . . . . . . . . . . . . . . 8 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . 8 DME64N and DME24N I/O Configuration . . 8 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DME64N/24N Audio System Overview 9 The DME64N/24N Configurable Digital Mixing Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System Examples . . . . . . . . . . . . . . . . . . . . . . . 10 DME64N/24N Audio System Network . . .
Introduction About the Documentation The following manuals are provided with the DME64N/24N. DME64N/24N Owner’s Manual (This document) This document covers the specifications, installation, and operation of the DME64N/24N. DME Designer Installation Guide This document covers the installation of the DME Designer software application and related drivers (USBMIDI driver, DME-N Network driver) on a computer, computer setup, and connection of the computer to the DME64N/24N.
The DME64N/24N Configurable Digital Mixing Engine DME64N/24N Audio System Overview The DME64N/24N Configurable Digital Mixing Engine In addition to basic mixing and matrix output functions, the DME64N/24N includes a full range of processing modules – equalizers, compressors, reverb and delay, effects, etc. – that can be patched together using the DME Designer software to support just about any audio system you need.
System Examples System Examples Single DME24N: A Meeting Room Installation Here’s an example of a single DME24N used to control the sound in four partitionable regions. The built-in microphone preamplifiers and A/D converters allow direct connection of up to 8 microphone inputs, while the 8 analog outputs can directly feed four stereo power amplifiers.
System Examples Multiple DME64N: Large Stadium Or Multi-purpose Hall System In this system live audio from microphones is mixed with background music and other sources in the central control room using a Yamaha DM1000 digital mixing console. A DM1000 equipped with an MY16-AE digital I/O card and an NHB32-C network hub bridge can feed the control room output to the system’s DME64N units over distances of up to 2 kilometers via multimode optical fiber cables.
System Examples Single DME64N: Sound Reinforcement For live sound reinforcement applications a DME64N can be connected to a Yamaha PM5D digital mixing console, for example, to provide significantly expanded processing power. In this type of application the DME64N could be used to provide up to an additional 64 matrix outs as well as output processing such as GEQs, level controls, crossovers, delays, and more. The DME-to-console connection can be made either the cascade connector.
DME64N/24N Audio System Network DME64N/24N Audio System Network To facilitate understanding and conceptualizing an overall DME64N/24N system, the terms “area” and “zone” are applied. The entire area serviced by the system is the “area,” while audio processing divisions within the area are “zones.” A single computer can be used to control the entire area as well as individual zones in a DME64N/24N audio system. Up to 16 DME64N/24N units can operate in any one zone.
DME64N/24N Audio System Control DME64N/24N Audio System Control To facilitate understanding and controlling an overall DME64N/24N system, the terms “component,” “parameter,” “scene,” and “user-defined parameter” are applied. Components & Parameters The individual audio modules (equalizers, compressors, etc.) are called “components.” Head amplifier modules are also prepared as components. Changing the parameters of components enables control over the operation of the components.
DME Designer DME Designer The DME Designer software application, supplied with the DME64N/24N, can be used to create configurations as well as control the entire area. DME64N/24N Audio System Overview A DME64N/24N network system cannot be set up entirely from the DME64N/24N alone. Configurations and scene data must be created on a computer running the DME Designer application, and then transferred from the computer to the DME64N/24N.
Front Panel The Controls and Connectors Front Panel DME64N ! 1 @ SCENE # HOME 2 ^ ) 9 $ UTILITY * % LEVEL º ¡ ™ ( CANCEL MUTE & £ ENTER 4 5 6 3 The Controls and Connectors DME24N ^ ) 9 & 1 ! @ SCENE 2 3 4 5 6 # HOME $ UTILITY * % LEVEL MUTE ™ ( CANCEL º ¡ £ ENTER 7 8 7 8 1 [USB] Connector A computer can be connected here when it is necessary to program or control the device. When a USB connection is to be used, the USB-MIDI driver must be installed on the computer.
Front Panel 5 [MIDI] Indicator # [UTILITY] Button Lights while data communication is occurring via the [MIDI] connector. Received data causes the indicator to light green, while transmitted data causes the indicator to light orange. The indicator will light green when reception and transmission occur simultaneously. If a problem occurs the indicator will light red. Calls the output level display.
Rear Panel Rear Panel 4 DME64N 1 2 6 7 ) 9 3 DME24N 5 4 3 The Controls and Connectors 1 2 9 1 [AC IN] Connector This is the device’s three-pronged AC power connector. Connect to the AC mains using the supplied AC power cord. See “Preparation” on page 20 for details. 6 7 5 8 NOTE Connect the device to only one ground point. Connecting the device to more than ground point can result in ground loops that can cause increased hum and noise.
Rear Panel 4 [MIDI IN] [MIDI OUT] [MIDI THRU] Connectors These are standard MIDI connectors that handle reception and transmission of MIDI data: [MIDI IN] receives MIDI data, [MIDI OUT] transmits MIDI data, and [MIDI THRU] re-transmits MIDI data received at the [MIDI IN] connector. See “MIDI Connection” on page 30 for connection details. 5 [WORD CLOCK IN] [WORD CLOCK OUT] Connectors These BNC connector receive and transmit word clock from and to external equipment.
Setup Procedure Preparation Setup Procedure Follow the steps outlined below to prepare the DME64N/24N for operation. 1. Install any required I/O cards. Refer to “I/O Card Installation” on page 22 for details. 2. Connect the AC power cord. CAUTION Be sure to turn all devices OFF before connecting AC mains power. Attach the cable clamp to prevent accidental disconnection. Attaching the cable clamp. Preparation Be sure to properly ground the device to prevent possible electrical shock.
Setup Procedure 3. Install the DME Designer software and necessary drivers on the computer to be used for zone control. See the separate “DME Designer Installation Guide” for details. 4. Connect the device to the computer and/or other equipment. Refer to “Connection” on page 24 for details. 5. Turn power to the computer, DME64N/24N, and related devices on. Press the DME64N/24N [POWER] switch to turn it on.
I/O Card Installation I/O Card Installation The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available card slot(s). Compatible I/O Cards As of July 2004, Yamaha mini-YGDAI cards that can be used with the DME64N/24N are as follows: Card Name Function Input Output No.
I/O Card Installation I/O Card Installation Procedure 1. Make sure that the DME64N/24N power is OFF. If the power is on, turn it off. 2. Loosen the two card slot screws and remove the slot cover, as shown in the diagram. N OT E Preparation The slot cover and screws will need to be re-attached if the I/O card is later removed from the slot, so keep them in a safe place. 3. Slide the I/O card into the slots in the guide rails, as shown in the diagram, and push the card into the slot.
Connection Connection The DME64N/24N must be connected to other DME64N/24N units as well as other audio equipment, according to the audio system design. Signal Types DME64N/24N audio system signals can be broadly categorized as follows. 1. Audio The DME64N/24N will be required to send and receive audio signals to and from other DME64N/24N units as well as other audio equipment. Audio signal transmission and reception will occur primarily via I/O cards installed in the unit’s I/O card slot(s).
Connection Other Zone Other Zone Zone ICP1 Switching Hub Router Computer GPI Controller (CP4SW/CP4SF/CP1SF) DME64N/24N DME64N/24N Matrix Output Processor Preparation Audio Signals (Power Amp, Recorder, etc.) Audio Signals (Microphone, CD Player, etc.) Audio Signals (Power Amp, Recorder, etc.
Connection USB Connection Connect the DME64N/24N [USB] connector to the computer’s USB connector using a USB cable. USB connections can be used in the following two ways: (1) Connect the computer to, and control the zone master DME64N/24N using the DME Designer. (2) Connect to any individual DME64N/24N and control that DME64N/24N unit using MIDI commands from a MIDI sequencer or similar software.
Connection Ethernet Connection ([NETWORK] Connector) Connect the [NETWORK] connector on the rear panel of the DME64N/24N to the network switching hub via a straight Ethernet cable. Ethernet connections can be used in the following two ways: • Connect the computer to the zone master DME64N/24N. • Connect the zone master DME64N/24N to zone slave DME64N/24N units. Appropriate IP addresses must be assigned to all devices connected to an Ethernet network.
Connection Control from a Computer Having the Same Network Address Zone Zone Master DME64N/24N (IP Address: 192.168.0.2) Ethernet Straight Cable Ethernet Straight Cable Switching Hub Ethernet Straight Cable Ethernet Straight Cable Computer (IP Address: 192.168.0.100) DME64N/24N DME64N/24N (IP Address: 192.168.0.3) (IP Address: 192.168.0.250) N OT E The IP addresses in the diagram are examples. Preparation N OT E Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds.
Connection Connecting Multiple Zones Port Settings Port Settings • Destination network address: 192.168.0.0 • Subnet mask: 255.255.255.0 • Gateway: 192.168.0.1 • Destination network address: 192.168.1.0 • Subnet mask: 255.255.255.0 • Gateway: 192.168.1.1 Zone Zone Zone Master Zone Master DME64N/24N (IP Address: 192.168.0.2) DME64N/24N (IP Address: 192.168.1.2) Ethernet Straight Cable Switching Hub Ethernet Straight Cable Ethernet Straight Cable DME64N/24N DME64N/24N (IP Address: 192.168.0.
Connection MIDI Connection In this case connection is made to the rear-panel [MIDI] connectors. MIDI commands are sent to the DME64N/24N from a MIDI device. N OT E Refer to “MIDI Page” on page 52 for MIDI setup details. N OT E The DME Designer can be used to set up the system so that scene recall operations and user parameter control can be carried out from connected MIDI devices. Refer to the DME Designer manual for details.
Connection GPI Connection GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear-panel [GPI] connectors. Using GPI a variety of control signals can be transferred between the DME64N/24N and external controllers or other devices. The optional CP4SW, CP4SF, and CP1SF control panels are also connected via GPI. N OT E For more information on the CP4SW, CP4SF, and CP1SF control panels refer to “CP4SW, CP4SF, and CP1SF” in the Appendix of this manual (page 59).
Connection CASCADE Connection (DME64N only) The rear-panel [CASCADE] connector can be connected to the [CASCADE] connector on another DME64N/24N or other compatible device via a dedicated cascade cable for bidirectional transfer of control, audio, and word clock signals. The communication direction automatically switches to unidirectional when connecting to a mixer such as the PM5D, or bidirectional when connecting to another DME64N/24N unit.
Connection WORD CLOCK Connection Word clock signals are transferred to and from external devices via the [WORD CLOCK IN] and [WORD CLOCK OUT] connectors. The [WORD CLOCK OUT] connector can be used to supply the DME64N/ 24N word clock to external equipment. Word clock is continuously output by the DME64N/24N during normal operation. The word clock signal from an external device can be received via the [WORD CLOCK IN] connector.
Connection REMOTE Connection The [REMOTE] connector can be connected to remotely-controllable Yamaha AD8HR or AD824 head amplifiers (preamplifiers), or RS-232C compatible controllers. Up to 8 head AD8HR/AD824 head amplifiers can be connected. Control can be handled either from the Utility display HA page (described on page 54 of this manual), or from the DME Designer application.
Connection Analog Audio Connection ([IN] and [OUT] Connectors) (DME24N only) The DME24N includes [IN] and [OUT] connectors for 8 channels of analog audio input and output. Wire the supplied Euroblock plugs as shown below. Head amplifier gain and phantom power settings can be made via the Utility display HA page described on page 54 of this manual, or via the DME Designer application. Cable Preparation Prepare cables to be attached to a Euroblock plug as shown below.
Connection Condenser Microphone Condenser Microphone 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 Connection Box (XLR → Euroblock conversion) THRU IN MIDI OUT WORD CLOCK REMOTE IN 8 7 6 5 4 3 2 IN OUT +V AC IN 1 75Ω TERMINATED OUT GND IN IN SLOT 8 7 6 5 8 7 6 5 4 3 2 1 4 3 2 1 OUT OUT DME24N N OT E Preparation Analog audio input and output can also be connected via an I/O Card installed in a DME64N/24N I/O card slot.
Connection I/O Slots The DME64N has four I/O card slots, and the DME24N has one I/O card slot. The number of audio input channels available on the DME64N/24N can be increased by plugging the appropriate mini-YGDAI I/O card(s) into the available card slot(s). Some types of cards also provide control and/or word clock transmission and reception functionality. Refer to “I/O Card Installation” on page 22 of this manual for card installation instructions.
The Panel Buttons and Displays Panel Operation and Displays The Panel Buttons and Displays By pressing the panel buttons it is possible to select the DME64N/24N Main display, Utility display, and Parameter Edit displays that allow individual settings to be edited and changed. refer to the pages listed below for more detailed information about each display.
Main Display Main Display The Main display will appear in a few seconds after the power is turned on. The Main display shows information about the current scene. NO T E Nothing will appear on the display if no scene data is stored in the DME64N/24N scene memory (this is the case when the unit is initially shipped, for example). Up to 24 parameters can be accessed from the DME64N/ 24N or ICP1 control panel for each scene. Six parameters are shown on the Main display at a time.
Parameter Edit Displays Parameter Edit Displays Parameter Edit displays will appear when the [SCENE], [MUTE], [MONITOR] or other button is pressed to allow scene changes, level adjustment, and other settings to be edited as required. Parameter Edit displays are also used to edit utility parameters.
Parameter Edit Displays 2. Rotate the dial to edit the value as required. List Parameters List parameters allow you to make one selection from a list of possibilities. Rotate the dial to scroll up or down the list. In some cases the centermost item on the display will be always highlighted as the list is scrolled, and in others the same item will remain highlight as the list is scrolled up or down. List Parameter with Center Item Always Highlighted 3.
Parameter Edit Displays ON/OFF Parameters Mute Switching Parameters that are either ON or OFF are edited via this type of display (e.g., Mute Parameter Edit display in “Mute Switching” on page 42). Turns the DME64N/24N output mute function ON or OFF. 1. Rotate the dial clockwise to select ON, or 1. Press the [MUTE] button. counterclockwise to select OFF. The Mute Parameter Edit display will appear. 2. Press enter to confirm the selection and close the window.
Parameter Edit Displays Scene Recall This procedure recalls a new scene (refer to page 14). NOTE If head amplifier parameters are included in the recalled scene data, the head amplifier settings will be changed accordingly. NO T E The same procedure is used for scene recall from an ICP1 control panel. Scene Store 1. Press the [SCENE] button. The Scene Recall display will appear. Stores the current scene data for later recall. NOTE This function can be accessed in the same way from the ICP1. 1.
Parameter Edit Displays Monitoring The monitor functions allow you to monitor the audio signal at the inputs or outputs of I/O slots, points between components, and other critical monitoring points. NO T E User-defined monitoring functions, such as monitoring at points between components, must specified via the DME Designer application. NO T E These functions cannot be accessed from the ICP1. 1. Press the [MONITOR] button. The slots available for monitoring will be shown in the parameter list. 2.
Spectrum Display Spectrum Display The monitor functions also provide spectrum analyzer type level display of the signal at the selected monitor point. NO T E Spectrum display is not available on the ICP1 control panel. Procedure 1. Select the monitor point for which you want to see a spectrum display from the list. 4 L/R Select Indicates when the spectrum display is for the left or right channel.
Level Meter Display 4 Peak Hold When the peak hold function is set to ON, peak levels are held indefinitely. Peak levels are cleared after one second when peak hold is set to OFF. Level Meter Display Individually displays the input/output level for each channel. NO T E Level display is not available on the ICP1 control panel. 1. Make sure that the Main display is showing. If the Main display is not showing, press the [CANCEL] to return. 2. Press the [UTILITY] button. The level meter display will appear.
Utility Displays Utility Displays Most basic DME64N/24N functions can be accessed via the Utility Display. Items accessible via the Utility display Item Name Version Date Battery Net Zone IP Adr. Link Mode MAC Adr.
Utility Displays Utility Display Operation The general procedure for operating the Utility displays is outlined below. 1. Press the [UTILITY] button for longer than 2 seconds from the Main display to go to the Utility display. 2. Press the [UTILITY] button as many times as 3 Date Shows the currently set date and time. The internal clock and calendar can be set here. Edit using the “Numeric Parameters” editing procedure described on page 40. NOTE “Zone slave” cannot be used to set this parameter.
Utility Displays 2 IP Adr. This is the device’s IP address. Edit using the “Numeric Parameters” editing procedure described on page 40. Display Setup (Disp) Page Provides access to a number of display parameters. NOTE The meter fall time (3) is not shown on the ICP1 control panel display. 1 2 Network Address Host Address 3 NO T E 3 Link Mode Shows the status of the [NETWORK] connector. The [NETWORK] connector can be set to operate in “10BaseT” or “100Base-TX” mode.
Utility Displays Security Setup (Lock) Page Panel lock and related settings. 1 2 3 4 1 Utility The lock status for the Utility display settings. This parameter can be set to “Unlock” or “Lock.” Unlock: The Utility display can be accessed without a password. Lock: A password must be entered to access the Utility display. 2 Panel Lock Boot Determines whether or not panel lock will be on when power to the device is turned on. This parameter can be set to “Unlock” or “Lock.
Utility Displays Miscellaneous Setup (Misc) Page Word Clock Setup (WCLK) Page This page includes parameters not available in any other page. Shows the status of incoming word clock signals, and allows setup of the DME64N/24N master word clock. NO T E NOTE The Remote setting (2) will not appear on the ICP1 control panel display. This page will not be displayed on the ICP1. 2 1 Scene Store Determines whether or not scene store operations are allowed.
Utility Displays The Status Icons A word clock signal is present, and this signal can be selected as the DME64N/24N word clock. MIDI Setup (MIDI) Page 3 No word clock signal (cannot be selected as the master clock). A word clock signal is present, but is not in sync with the master word clock. Currently selected as the DME64N/24N word clock. Currently selected as the DME64N/24N word clock, but the clock signal is not useable. Inactive slot channel, or no I/O card is present in the slot.
Utility Displays NO T E “DAW” stands for “Digital Audio Workstation.” ProTools, Logic, and Cubase are DAW applications, and this parameter provides direct compatibility with a number of physical controls surfaces that are available for use with these DAW software packages. GPI Setup (GPI) Page Input calibration parameters for the [GPI] connector. NOTE This page will not appear on the ICP1 display. The following parameters are available when the DAW parameter is set to OFF.
Utility Displays Head Amplifier Setup (HA) Page Provides access to the head amplifier settings. Refer to “REMOTE Connection” on page 34 for head amplifier control signal connection. NO T E Available settings of the AD8HR are “D OUT A,” “WCLK IN,” “INT44.1K,” “INT48K,” “INT88.2K,” and “INT96K.” This page will not appear on the ICP1 display. D OUT A: Sets the word clock signal at the digital input as the master clock of the AD8HR.
Utility Displays 4 Gain Individually sets the gain of each head amplifier channel. Edit using the “Numeric Parameters” editing procedure described on page 40. NO T E The gain of the DME24N internal head amplifiers can be adjusted from +10 dB to –60 dB in 1-dB increments. The internal circuitry switches at about the –45-dB point, and the signal is automatically muted at that point to prevent noise.
Options Appendix Options The ICP1, CP4SW, CP1SF, and CP4SF controllers are optionally available for remote external control of the DME64N/ 24N. The ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. ICP1 This controller connects to the DME64N/24N via Ethernet. Like the DME64N/24N, each ICP1 unit has it’s own IP address. With a display that replicates the display on the DME64N/24N, the ICP1 allows comprehensive, familiar control from remote locations.
Options 5 [F5] Button When the Main display is showing this button calls the Parameter Edit display for the middle user-defined parameter in the lower part of the display. When the Utility display is showing it has the same function as the [ ▼ ] cursor button on the DME64N/24N. 6 [F6/MUTE] Button When the Main display is showing this button calls the Parameter Edit display for the user-defined parameter in the lower right corner of the display.
Options 2. Connect the adaptor box to a network hub or the DME64N/24N. Use a “straight” cable for connection to a hub, or a “cross” cable for direct connection to the DME64N/24N. N OT E • Use a 100Base-TX/10Base-T switching hub. • When using category 5 UTP (Unshielded Twisted Pair) cable, the total length of the cables connecting the control panel unit to the hub or DME64N/24N can be up to 100 meters.
Options CP4SW, CP4SF, and CP1SF These controllers connect to the DME64N/24N via its GPI interface. These controllers only control the DME64N/24N unit to which they are directly connected. The CP4SW is a four-switch unit with four indicator LEDs, while the CP1SF and CP4SF have one and four faders, switches, and LEDs, respectively. The parameters to be controlled by the switches and faders on these controllers can be specified via the DME Designer.
Options Control Panel Installation 1. Screw the frame plate to the terminal box. N OT E • Terminal box not included. Use a standard (US-type) wall box: 3-gang for CP4SF and 1-gang for CP4SW and CP1SF with depth 44 millimeters or more. • The screw heads should extend from the frame plate by no more than 3 millimeters. 2. Screw the control panel to the frame plate. N OT E Tighten the screws used to attach the control panel to the frame plate with a torque of less than 1.5 Nm.
Error Messages Error Messages Message Meaning Action Error messages Cannot Select No selectable items are available in the scene or monitoring point list display. Make the appropriate settings via the DME Designer application. Flash Rom Full The flash ROM is full. Reduce the number of stored scenes. Invalid Password An invalid password has been entered. Enter the correct password. If you have lost or forgotten your password, contact your Yamaha service center or representative.
Error Messages Message Meaning Info set up via the Utility display (other than head amplifier info) is being saved. (Do not turn power off.) Scene Recalling Scene recall in progress. None required. Scene Storing Scene store in progress. (Do not turn power off.) None required. SLOT1 Sync Err The DME64N/24N clock is not synchronized with the clock of the card installed in I/O slot 1. Make sure that the DME64N/24N and the card installed in I/O slot 1 are set to use the same word clock.
Troubleshooting Troubleshooting Possible Causes Possible Solutions The power cord is not plugged into an appropriate AC outlet. Make sure that the power cord is plugged into an appropriate AC outlet. Refer to “Preparation” on page 20. The POWER switch is turned OFF. Make sure that the POWER switch is turned ON. Refer to “Preparation” on page 20. There is a fault in the DME64N/24N. Contact your Yamaha service center or representative. The DME64N/24N power is not turned on.
Troubleshooting Symptom Possible Solutions Disengage the Panel Lock function. Refer to the “Panel Lock” section on page 39. No DME64N/24N is assigned as the zone master. For each zone one DME64N/24N must be assigned as the zone master. This can be accomplished via the Utility display “Net” page described on page 48 of this document. The IP address is not set properly. Set an appropriate IP address. This can be accomplished via the Utility display “Net” page described on page 48 of this document.
Specifications Specifications Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Sampling Frequency Internal 44.1kHz, 48kHz, 88.2kHz, 96kHz External Normal Rate: 39.69 – 50.88kHz Double Rate: 79.39 – 101.
Connector Pin Assign Connector Pin Assign [CASCADE IN/OUT] Connectors (DME64N only) CASCADE IN Pin No. Appendix 66 CASCADE OUT Signal Pin No. Signal Pin No. Signal Pin No.
Connector Pin Assign [NETWORK] Connector (100Base-TX Ethernet, RJ-45) Pin Connection 1 TxD+ 2 TxD– 3 RxD+ 4 Unused 5 Unused 6 RxD– 7 Unused 8 Unused Straight/Cross Cable Wiring Details Cross Cables Pins Pins 1 —— 1 1 —— 3 2 —— 2 2 —— 6 3 —— 3 3 —— 1 4 —— 4 4 —— 4 5 —— 5 5 —— 5 6 —— 6 6 —— 2 7 —— 7 7 —— 7 8 —— 8 8 —— 8 Appendix Straight Cables DME64N/24N Owner’s Manual 67
Dimensions Dimensions Unit: mm 12.5 53.5 278 388 411.5 394 405 11 DME64N 423 145 17.5 96 132 18.5 4-M3 90 30 300 90 480 11 DME24N 12.5 53.5 278 388 411.
MIDI Data Format MIDI Data Format 1. DME64N/24N MIDI Functions 1.1 Scene Change Scene recall occurs according to the “MIDI Program Change Table” assignments when appropriate MIDI Bank Select MSB/LSB and Program Change messages are received by the DME64N/24N. Corresponding MIDI Bank Select MSB/LSB and Program Change messages are also transmitted by the DME64N/24N when a scene recall operation is carried out via the panel controls, as specified by the “MIDI Program Change Table” assignments.
MIDI Data Format 3. MIDI Setup Specifies basic MIDI operation. 3.1 Host Select Selects the input/output port to be used for MIDI communication. 3.2 DAW Controller Specifies the DAW controller type when a DAW control surface is to be used to control the DME64N/24N. When Type 1/ 2 is selected, Host Select is automatically set to MIDI. 3.3 MIDI Tx Channel Specifies the MIDI transmit channel (1 ~ 16). 3.4 MIDI Rx Channel Specified the MIDI receive channel (1 ~ 16). 3.
MIDI Data Format 4.1 Program Change (Cnh) Receive When the “Program Change Rx Switch” is on, Program Change messages are received on the MIDI channel specified by the “MIDI Rx Channel” parameter. If the “Program Change Omni Switch” is also on, however, Program Change messages will be received on all MIDI channels regardless of the “MIDI Rx Channel” setting. When a Program Change message is received, the scene assigned to the received program number in the “MIDI Program Change table” is recalled.
MIDI Data Format 4.5 Parameter Change (F0h ~ F7h) Receive When the “Parameter Change Rx Switch” is On, Parameter Change messages are received on the MIDI channel specified by the “Device ID (Rx Ch)” parameter. Transmit When the “Parameter Change Tx Switch” is On, appropriate Parameter Change data will be transmitted when a parameter is edited via the panel controls, as specified by the “MIDI Parameter Change table” and “MIDI Tx Channel” settings.
MIDI Data Format YAMAHA [Digital Mixing Engine] Model DME64N/24N MIDI Implementation Chart Function...
Glossary Glossary Terms Appendix 74 Explanations 100Base-TX A physical specification for a 100 Mbps Ethernet network connection using 2-conductor Category 5 UTP cable included in the IEEE 802.3u standard. Maximum data transfer distance is 100 meters. 10Base-T A physical specification for a 10 Mbps Ethernet network connection using 2-conductor Category 3 UTP cable included in the IEEE 802.3i standard. Maximum data transfer distance is 100 meters.
Glossary Terms Explanations An 8-conductor modular connector used for Ethernet cable and ISDN telephone connections. The appearance is similar to the RJ-11 connectors used for telephone lines, but the connector is actually somewhat larger. “RJ” stands for “Registered Jack,” and is a connector type included in the Bell System USOC (Universal Service Ordering Codes) standards. Router An equipment that relays data in network by selecting the most effective route.
Index Index +48V ...................................................................................... 55 [E] [ ▲ ] [ ▼ ] [F] Buttons ........................................... 17 100Base-TX (Glossary) .......................................................... 74 10Base-T (Glossary) ............................................................... 74 [96kHz] [88.2kHz] [48kHz] [44.1kHz] Indicator ................. 16 A [AC IN] Connector ...............................................................
Index I I/O card ................................................................................. 22 I/O card (installation procedure) ............................................ 23 I/O Slots ................................................................................ 19 ICP1 ...................................................................................... 56 [IN] [OUT] Connectors .................................................. 19, 35 Info Page ................................................
Index Scene Recall ........................................................................... 43 Scene Store (Misc Page) ......................................................... 51 Scene Store (Operation) ......................................................... 43 security cover mounting ......................................................... 20 Security Setup (Lock) Page ..................................................... 50 [SIGNAL] Indicator .......................................................
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd.
Yamaha Manual Library http://www2.yamaha.co.jp/manual/english/ This document is printed on chlorine free (ECF) paper with soy ink. U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2004 Yamaha Corporation WC32570 406MWCP22.
