Owner`s manual

ManualsBrandsYamaha ManualsHousehold AppliancesDKC-850

Disklavier Control Unit DKC-850

Connection Guide

DisklavierTV service is available for U.S. customers only.

The DKC-850 Disklavier control unit can be connected to several models of Yamaha Disklavier pianos,

however, connections and setup procedures vary depending on the piano model. Check the model number

on the existing control unit and find your piano model following the descriptions below before connecting.

Note:

The model number of the control unit is on the upper part of the display.

■ Compatible Models when Equipped with DKC-850

If you are using the piano listed below, replace the existing control unit with DKC-850.

For details on connections and setup, see “Replacing the Existing Control Unit with DKC-850” on page 2.

Important:

Please keep your existing control unit for future maintenance.

Checking the Type of Your Piano

Models Model Number on the Control Unit

Upright pianos Disklavier Mark II XG Series DKC500R, DKC500RXG, DKC500RW,

DKC500RWXG

Disklavier Mark II XG Series (MX116, MX22, MX500) DKC50R

Disklavier Mark III Series (DU1A) DKC55RCD

Grand pianos Disklavier Mark II XG Series DKC500R, DKC500RXG, DKC500RW,

DKC500RWXG

Disklavier Mark III Series Full-Function Models DKC55RCD

Disklavier Mark III Series Standard Models DKC60RCD

Disklavier Mark III Series PRO Models DKC55RCD

Disklavier Mark III Series Playback Models DKC55, DKC55CD

Summary of content (6 pages)

PAGE 1
powered by RemoteLive™ Disklavier Control Unit DKC-850 Connection Guide DisklavierTV service is available for U.S. customers only. Checking the Type of Your Piano The DKC-850 Disklavier control unit can be connected to several models of Yamaha Disklavier pianos, however, connections and setup procedures vary depending on the piano model. Check the model number on the existing control unit and find your piano model following the descriptions below before connecting.
PAGE 2
Replacing the Existing Control Unit with DKC-850 Connect DKC-850 to your piano, replacing with the existing control unit. 8 7 5 Tighten DKC-850 6 Conversion cable (supplied) AC adaptor (PJP-PS02/PJP-PS04) (supplied) Connect monitor speakers. See page 4. Power cable (supplied) Control cable Your piano 4 3 Tighten 9 Loosen Cautions • Use the Yamaha PJP-PS02/PJP-PS04 adaptor, or an equivalent recommended by Yamaha. Use of other AC adaptors may result in damage, overheating, or fire.
PAGE 3
Important • Be sure to backup the data on your existing control unit to a floppy disk before connecting. • Please keep your original control unit for future maintenance. 1 Turn on your piano, and reset settings on your control unit to its factory default. For details on setting, refer to your piano’s owner’s manual. 2 Turn off your piano, and disconnect the power cable from the AC wall outlet.
PAGE 4
Connecting Monitor Speakers To listen to the internal XG tone generator voices, you have to connect monitor speakers. Connection methods vary depending on whether your piano is equipped with the Silent Piano™ function or not. ■ For Pianos Equipped with the Silent Piano™ Function Connect the AUX IN jacks of your piano to the OUTPUT jacks on the rear of DKC-850 with the supplied audio cable. For models with the control box Connect with the supplied audio cable (pin plugs – stereo mini plug).
PAGE 5
Setting the Type of Your Piano [SYSTEM] “PianoType” After you have connected DKC-850 to your piano, you must set the type of your piano. 1 Press [SYSTEM] on the remote control. The system menu screen appears. !"#$%{ 2 Select “PianoType” with the cursor buttons ([ [ ]), then press [ENTER]. ][ ][ ] =SYSTEM MENU= _(2/2) *Language *PianoType *Display The piano type setup screen appears.
PAGE 6
P.O.