CD-R/RW Drive CRW6416S SERIES OWNER’S OWNER’S MANUAL MANUAL BEDIENUNGSANLEITUNG BEDIENUNGSANLEITUNG MODE MODE D’EMPLOI D'EMPLOI MANUAL MANUAL DE DE INSTRUCCIONES INSTRUCCIONES
6416S_e15.qx 7/26/99 3:38 PM Page 2 FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
6/29/99 6:00 PM Page 3 CD-R/RW Drive CRW6416S SERIES OWNER’S MANUAL i English 6416S_e15.
6416S_e15.qx 6/29/99 6:00 PM Page 4 SAFETY PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING These precautions explain how to use the device correctly and safely, thereby preventing injury to yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION section, according to the likelihood and nature of any potential injuries or damage inflicted. They relate to your personal safety, and also help you minimize the risk of damaging the device.
6416S_e15.qx 6/29/99 6:00 PM Page 5 CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: ● Always unplug the computer from the electrical outlet if it will not be used for a prolonged period of time or if there is a risk of lightning. Otherwise, there is an increased risk of electrical shock, short-circuiting or fire.
416S_e15.qx 6/29/99 6:00 PM Page 6 ■ About CD-R/RW discs Please read the following regarding the handling of CD-R/RW discs. 1. Do not expose discs to excessive heat or vibrations or extreme cold or heat (such as in direct sunlight or near a heater). 2. Do not touch disc surfaces. When handling a disc, hold it by its edges. 3. Remove dust and dirt from disc surfaces. Use air-based dust removers. The surfaces may be scratched if wiped with a dry cloth. 4.
6416S_e15.qx 6/29/99 6:00 PM Page 7 Table of Contents Setup Flowchart ..........................................................................................................................1 Introduction ..................................................................................................................................2 Features of the CRW6416S Drive ....................................................2 System Configuration ...............................................................
6416S_e15.qx 6/29/99 6:00 PM Page 8 Setup Flowchart This flowchart shows the procedure for setting up the CRW6416S drive. For easy cross-referencing, the relevant pages in this manual are also given. STEP 1 Do you have a SCSI adapter card? STEP 1-1 NO Obtain a SCSI adapter card Recommended models: Adaptec AHA2940-series (PCI) YES STEP Check that the SCSI adapter 2 card is installed correctly SCSI card into the appropriate PCI slot on the computer.
6416S_e15.qx 6/29/99 6:00 PM Page 9 Introduction Features of the CRW6416S Drive 6X Speed Writing to CD-R, 4X Speed Writing to CD-RW and 16X Speed Reading The CRW6416S drive can write to CD-R at 6X, 4X or 1X speed and write/overwrite to CD-RW at 4X or 2X speed. It can also read from CD-R and CD-ROM media at up to 16X speed. Supports a Wide Range of CD Formats The CRW6416S drive can read from and write to CD-ROM in standard ISO9660 format and to audio CD in CD-DA format.
6416S_e15.qx 6/29/99 6:00 PM Page 10 System Configuration In order to use the CRW6416S drive, your computer system will need to meet the following set of requirements. Computer The minimum system requirements for using the CRW6416S drive are as follows: ● Any fully PC/AT-compatible computer. ● A Pentium-class or higher CPU running at 133MHz or faster. (200MHz or faster recommended.) ● OS: Windows 95, Windows 98, or Windows NT4.0 with Service Pack 3/4/5. ● A 5.25-inch drive bay for mounting the drive.
6416S_e15.qx 6/29/99 6:00 PM Page 11 System Configuration Media The CRW6416S drive is compatible with discs which meet the following specifications: ● CD-R discs: Use discs that conform to the Orange Book Part 2 standards. When writing to CD-R at 4X or 6X speed, you should use discs that have been designed for high-speed recording. ● CD-RW discs: Use discs that conform to the Orange Book Part 3 standards.
6416S_e15.qx 6/29/99 6:00 PM Page 12 System Configuration Tools You will need the following tools at hand when installing the CRW6416S drive. Philips Screwdriver You will need to use this when removing the cover of your computer and when mounting the drive. You may also need to temporarily remove the sound card to gain access to the CD audio connectors. In which case a small screw retaining the sound card’s face plate has to be removed.
6416S_e15.qx 6/29/99 6:00 PM Page 13 Front and Rear of Unit Front Panel The CRW6416S drive’s front panel features the following: Manual eject hole Only use this if no other method is available for unloading a disc. Disc tray The tray is used to hold the disc. It slides out from the drive unit when a disc needs to be loaded or unloaded. Headphone jack You can connect stereo headphones to this stereo mini jack and listen to audio CDs loaded in the drive.
6416S_e15.qx 6/29/99 6:00 PM Page 14 Front and Rear of Unit Rear Panel The CRW6416S drive’s rear panel features the following: SCSI connector Insert the connector of the SCSI ribbon cable here. Make sure you align the red line of the ribbon cable with pin 1 of the drive’s connector, marked “SCSI INTERFACE CONNECTOR 1.
6416S_e15.qx 6/29/99 6:00 PM Page 15 Installation This section gives a step-by-step guide to installing the CRW6416S drive. Make sure you have all the necessary tools. First Steps Once you have taken the CRW6416S drive out of its packaging, you should immediately note down the serial number shown on the top of the drive together with a barcode. You may need to refer to this number when requesting User Support services.
6416S_e15.qx 6/29/99 6:00 PM Page 16 Installation To set each jumper switch, you have to bridge the two pins in the respective column of the grid with a plastic shunt. Shunts are already attached to the jumper switches in their default configurations.
6416S_e15.qx 6/29/99 6:00 PM Page 17 Installation 1 SCSI ID number Each of the SCSI devices connected to the computer is identified by its SCSI ID number. You need to assign a number from “0” to “7” for each SCSI device. Commonly, ID number “7” is reserved for the computer’s SCSI adapter card itself. Therefore, the CRW6416S can actually be assigned an ID number from “0” to “6.” If it’s the first device in the chain, you should assign it ID number “0.
6416S_e15.qx 6/29/99 6:00 PM Page 18 Installation 2 Parity Check The parity check is used for error correction during data transmissions. If parity-checking has to be disabled, the shunt on the Parity jumper switch should be removed. Parity on (Default) 1 24 Parity off ID SELECT PARITY TERMINATOR BLOCK SIZE 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE n By factory default, the Parity switch is set to “on” and should normally be left in this state.
6416S_e15.qx 6/29/99 6:00 PM Page 19 Installation Termination on (Default) 1 24 Termination off ID SELECT PARITY TERMINATOR BLOCK SIZE 1 24 ID SELECT PARITY TERMINATOR BLOCK SIZE Set to “on” if CRW6416S drive is last device on SCSI chain 4 Block Size The data block size of the CRW6416S can be set to 512 bytes per sector by setting the Block Size jumper switch to “on.” This is necessary when installing the CRW6416S on a UNIX-based workstation. It is not necessary for Windows 95/98/NT computers.
6416S_e15.qx 6/29/99 6:00 PM Page 20 Installation Installing the CRW6416S Drive You can install the CRW6416S drive in one of two possible ways: ● As an additional drive If the casing of your computer has a spare 5.25-inch drive bay available, such as with many tower-type designs, you can fit the CRW6416S drive in addition to the computer’s existing CD-ROM drive. CRW6416S ● As a replacement drive If the casing of your computer does not have a spare 5.
6416S_e15.qx 6/29/99 6:00 PM Page 21 Installation Fitting the CRW6416S as an Additional Drive 1 Power down your computer and unplug it from the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CRW6416S drive. 2 Remove the outer casing of the computer. If you need to remove screws in the process, make sure you don’t lose them.
6416S_e15.qx 6/29/99 6:00 PM Page 22 Installation 3 Touch a metal part of the computer’s chassis or power supply unit to drain any static charge that may have built up inside your body. Drain any static charge You can permanently damage equipment if you touch it while there is any static charge in your body. 4 Remove the front cover of a vacant 5.25-inch drive bay slot in the computer and slide the drive backwards into the slot.
6416S_e15.qx 6/29/99 6:00 PM Page 23 Installation 5 Leave enough room behind the drive for connecting the power, SCSI and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place. 6 Remove the SCSI adapter card from the computer and turn its termination OFF so that internal SCSI devices may be connected. Refer to the documentation that came with your SCSI adapter card for further details.
6416S_e15.qx 6/29/99 6:00 PM Page 24 Installation 7 Connect one end of the 50-pin SCSI flat cable to the computer’s SCSI adapter card. Align the red line of the cable with Pin 1 of the card’s SCSI connector. Next, connect a free 50-pin connector on the SCSI flat cable to the back of the CRW6416S drive such that the red line on the cable is aligned with pin 1, marked “SCSI INTERFACE CONNECTOR 1.” Then place the SCSI card back in its original PCI slot and secure its mounting bracket using a screw.
6416S_e15.qx 6/29/99 6:00 PM Page 25 Installation 8 Connect the audio cable between the CRW6416S drive and the computer’s sound card, or the motherboard’s audio connector if it has built-in audio. One end of the audio cable has two connectors: a smaller type and a larger type. Choose one that matches your sound card’s connector. The connector at other end of the cable is connected to “AUDIO OUT” of the CRW6416S drive. Make sure connector’s lug is at the top.
6416S_e15.qx 6/29/99 6:00 PM Page 26 Installation 9 Connect a 4-pin power cable to the power supply connector of the CRW6416S marked “DC INPUT.” AUDI O OU T R G L 1 24 ID SE PARI LECT TY TERM BLOCIN ATOR K SIZ E SCSI INTE RF CONN ACE ECTO R DC 1 INPU +5V T G + 12V Top Top 4-pin power cable Bottom n There may be more than one 4-pin power cable available. Any may be used. n These connectors are D-shaped so it is only possible to connect the power cables the correct way round.
6416S_e15.qx 6/29/99 6:00 PM Page 27 Installation ! Attach the outer casing of the computer and any screws that were removed. @ Reconnect the computer to the AC outlet and power it up. n When you power up the computer, make sure both LEDs on the front panel of the CRW6416S drive are lit.
6416S_e15.qx 6/29/99 6:00 PM Page 28 Installation # After the computer’s operating system has loaded, open the Control Panel and double-click on the System icon. Select the Device Manager tab and double-click on CDROM. If the drive has been correctly installed, it should be listed as shown below. Similarly, double-click on SCSI controllers and the SCSI adapter card should be listed as shown below if it has been properly installed.
6416S_e15.qx 6/29/99 6:00 PM Page 29 Installation Replacing an Existing CD-ROM Drive with the CRW6416S n The existing CD-ROM drive in the computer is assumed to be an IDE-type. 1 Power down your computer and unplug it from the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CRW6416S drive. 2 Remove the outer casing of the computer.
6416S_e15.qx 6/29/99 6:00 PM Page 30 Installation 3 Touch a metal part of the computer’s chassis or power supply unit to drain any static charge that may have built up inside your body. Drain any static charge You can permanently damage equipment if you touch it while there is any static charge in your body. 4 Disconnect all the cables connected to the rear of the existing CD-ROM drive, and also disconnect the audio cable from the sound card or motherboard’s audio connector.
6416S_e15.qx 6/29/99 6:00 PM Page 31 Installation 5 Remove the four screws holding the CD-ROM drive in place, then slide the drive forward and out from the drive bay. Slide the CRW6416S drive backwards into the now-vacant bay without applying excessive force. CD-ROM drive CRW6416S 6 Leave enough room behind the drive for connecting the power, SCSI and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place.
6416S_e15.qx 6/29/99 6:00 PM Page 32 Installation 7 Remove the SCSI adapter card from the computer and turn its termination OFF so that internal SCSI devices may be connected. Refer to the documentation that came with your SCSI adapter card for further details. SCSI adapter card n Some SCSI adapter cards are capable of auto-termination. If your card is of this type, you will not need to remove it from its slot since you will not need to set any of its switches or jumpers.
6416S_e15.qx 6/29/99 6:00 PM Page 33 Installation 8 Connect one end of the 50-pin SCSI flat cable to the computer’s SCSI adapter card. Align the red line of the cable with Pin 1 of the card’s SCSI connector. Next, connect a free 50-pin connector on the SCSI flat cable to the back of the CRW6416S drive such that the red line on the cable is aligned with pin 1, marked “SCSI INTERFACE CONNECTOR 1.” Then place the SCSI card back in its original PCI slot and secure its mounting bracket using a screw.
6416S_e15.qx 6/29/99 6:00 PM Page 34 Installation 9 Connect the audio cable between the CRW6416S drive and the computer’s sound card, or the motherboard’s audio connector if it has built-in audio. One end of the audio cable has two connectors: a smaller type and a larger type. Choose one that matches your sound card’s connector. The connector at other end of the cable is connected to “AUDIO OUT” of the CRW6416S drive. Make sure connector’s lug is at the top.
6416S_e15.qx 6/29/99 6:00 PM Page 35 Installation ) Connect the 4-pin power cable to the power supply connector of the CRW6416S marked “DC INPUT.” AUDI O OU T R G L 1 24 ID SE PARI LECT TY TERM BLOCIN ATOR K SIZ E SCSI INTE RF CONN ACE ECTO R DC 1 INPU +5V T G + 12V Top Top 4-pin power cable Bottom n There may be more than one 4-pin power cable available. Any may be used. n These connectors are D-shaped so it is only possible to connect the power cables the correct way round.
6416S_e15.qx 6/29/99 6:00 PM Page 36 Installation @ Attach the outer casing of the computer and any screws that were removed. # Reconnect the computer to the AC outlet and power it up. n When you power up the computer, make sure both LEDs on the front panel of the CRW6416S drive are lit.
6416S_e15.qx 6/29/99 6:00 PM Page 37 Installation $ After the computer’s operating system has loaded, open the Control Panel and double-click on the System icon. Select the Device Manager tab and double-click on CDROM. If the drive has been correctly installed, it should be listed as shown below. Similarly, double-click on SCSI controllers and the SCSI adapter card should be listed as shown below if it has been properly installed.
6416S_e15.qx 6/29/99 6:00 PM Page 38 Operation This section explains how to operate the CRW6416S drive after you have installed it. Loading a Disc 1 2 1 Press the Eject button on the CRW6416S drive’s front panel. 2 Place the disc onto the tray with its label or printing facing upward. 3 Press the Eject button to close the tray. n When a disc is loaded, the ON/DISC LED is lit up in orange first, then changes to green. For more details, refer to page 38.
6416S_e15.qx 6/29/99 6:00 PM Page 39 Operation n The disc tray will not open if the computer is not switched on. Also, depending on the SCSI adapter card settings, it may not open if the drive is busy reading a disc. n Only remove the disc after the disc tray has opened fully. Otherwise, you risk damaging the drive or the disc. Manually Ejecting a Disc If the disc tray fails to open for some reason, such as a power outage, the it can be opened manually.
6416S_e15.qx 6/29/99 6:00 PM Page 40 Troubleshooting Please also refer to the Yamaha web site for more information. Yamaha web site URL: http://www.yamaha.co.jp/english/product/computer/ The drive does not power up. ● Is the 4-pin power cable from the computer’s power supply attached correctly? The computer does not start up. ● Is the SCSI card installed correctly? Please read the instructions that came with your SCSI card for details. The CRW6416S drive is not recognized.
6416S_e15.qx 6/29/99 6:00 PM Page 41 Troubleshooting ● Is the terminator on the CRW6416S drive set correctly? It should be set to ON only if it is the last device on the SCSI chain. Otherwise, it should be set to OFF. (→P. 11) ● Is the termination on the SCSI card set such that internal SCSI devices can be connected? Please read the instructions that came with your SCSI card for details. ● To write to CD-R/RW discs, your CD writing software must support the CRW6416S drive.
6416S_e15.qx 6/29/99 6:00 PM Page 42 Troubleshooting The drive ejects or fails to read the disc, or the ON/DISC LED continues to blink in orange after the disc has been loaded (meaning that the disc has not been recognized). ● Disconnect the SCSI cable from the drive but leave the power cable connected, then load a disc. ● You may be trying to write to an unusable disc. If the drive fails to write to a variety of different discs, it may be faulty and you should contact your nearest Yamaha dealer.
6416S_e15.qx 6/29/99 6:00 PM Page 43 Appendix Writing Modes Disc-at-Once (DAO) This mode is used when writing a complete disc in a single pass without pausing. Data cannot be added later, even if the full capacity of the blank disc has not been used. Although the data written from start to finish is known as a “session,” no further sessions can be added later. This is why Disc-at-Once mode is sometimes referred to as Single Session.
6416S_e15.qx 6/29/99 6:00 PM Page 44 Appendix Session-at-Once (SAO) This mode is used when writing each session in a single pass without pausing. More sessions can be added later if there is enough space left on the disc. Example (CD Extra) Audio Audio Audio Data Track 1 Track 2 Track 3 Track 4 (Session 1) (Session 2) n With CD Extra, the audio is written in the first session and the data is written in the second. A maximum of 99 tracks can be written.
6416S_e15.qx 6/29/99 6:00 PM Page 45 Appendix Determining the firmware version of the CRW6416S drive (in Windows 95/98) Go to Control Panel | System | Device Manager tab, double-click on CDROM, then double-click on Yamaha CRW6416S.
6416S_e15.qx 6/29/99 6:00 PM Page 46 Appendix CRW6416S Specifications Supported Write/Read Format CD-DA CD-ROM CD-ROM XA CD-I CD-Bridge CD Extra Video CD Note) Excludes ADPCM Encode/Decode & Video Encode/Decode functions. Writing Methods Disc-at-Once (DAO) Session-at-Once (SAO) Track-at-Once (TAO) Packet writing (variable, fixed) Writing/Reading Speed Writing CD-R CD-RW 1X, 4X, 6X 2X, 4X Reading 9X-16X (max) Partial CAV Note) • CD-DA extraction: 10X (max) • Drive can play CD-DA at 1X speed only.
6416S_e15.qx 6/29/99 6:00 PM Page 47 Appendix Sector Size 2048 ~ 2352 B 512 B (read only) Interface SCSI-2 (Fast SCSI) Installing style Horizontal Disc Loading Type Tray loading Audio Out Line Out Frequency Range: 20 ~ 20,000Hz Output Level: 1 Vrms Power Consumption 11W (when writing or reading) Power Supply 5V DC ±5% 12V DC ±10% Operating Environment Temperature Humidity Dimension Width: 146.0 mm Height: 41.3 mm (excludes 0.5 mm projection at bottom) Depth: 193.
6416S_e15.qx 6/29/99 6:00 PM Page 48 Index 4-pin power cable ..................................19, 28 O ON/DISC LED................................................6 A Active Desktop ............................................35 additional drive ............................................13 audio cable ............................................18, 27 AUDIO OUT ..................................................7 B BIOS ............................................................33 block size ......
Address.qx 7/26/99 3:39 PM Page 1 Distributors and Head Offices / Bertrieb und HauptgeschŠftsstelle Distributeurs et si•ges sociaux / Distribuidores y Casas matrices If you have any questions, please contact your dealer or one of the following companies. Pour plus de détails sur les produits, veuillez vous adresser à Yamaha ou au distributeur le plus proche figurant dans la liste suivante : Bei weiteren Fragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden Firmen.
XW387B0
