English SERIES User Guide Guide de l’utilisateur Bedienungsanleitung ON/ DISC READ/ WRITE Deutsch Français CRW4416S
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recorder CRW4416S CRW4416S-NB This device complies with Part 15 of the FCC Rules.
Laser Diode Properties Material : GaAlAs Wavelength : 783-789 nm Emission Duration : Continuous Laser Output Power : Less than 44.6 µW* * This output is value measured at a distance 200mm from the objective lens surface on the optical pick-up block. ANSI Class : Class 1 CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING WARNING ❢ WARNING ❢ • The temperature where CRW4416S is located should be between 5ºC and 40ºC (41ºF – 104ºF), when used in a fan-cooled system. • Do not disassemble the CRW4416S cover to reduce the risk of electric shock. • Always remove the disc before transporting CRW4416S.
Important Precautions Important Precautions Please read the following precautions before attempting to operate the CRW4416S. • Before recording a disc, be sure to clean the disc and tray using an air aerosol-type dust remover. A dust particle on the disc may cause recording to fail, producing an unusable disc. • Always record in a dust-free environment. If the disc must be removed from the CRW4416S before recording is finished, store the disc in a clean, dustfree environment.
Table of Contents Table of Contents Introduction ...............................................................................1 CRW4416S Features .......................................................1 Orange Book Compatible Recording ..............................2 Chapter 1 - System Configuration ......................................3 Computer .........................................................................3 Software ...........................................................................
Introduction Introduction Thank you for purchasing a Yamaha CRW4416S drive. Please read this manual before using the drive in order to make the best use of the superior CRW4416S functions. After reading, please retain this manual for future reference. CRW4416S Features ■ 4xS Recording (Rewritable) - 4xS Recording (Recordable) 16xS Reading The CRW4416S is able to write (overwrite) CD-RW discs at quad speed, double speed, and is able to write CD-R discs at quad speed, double speed, or normal speed.
Introduction Orange Book Compatible Recording Track at Once In this mode, data can be recorded to disc one track at a time. Discs recorded in this mode cannot be played in CD players or CDROM drives other than a CD-RW or a CD-R drive until the session is closed. Multisession In this mode, data can be recorded to disc in stages (one session at a time). Additional data can be written later. Disc at Once In this mode, data can be recorded to an entire disc in one pass.
Chapter 1 - System Configuration Chapter 1 - System Configuration Before using the CRW4416S, make sure that you have all of the items on the list of included items. In order to use the CRW4416S, you will require the following.
Chapter 1 - System Configuration Tools Phillips screwdriver This is used to remove the cover of your computer, and to install the Yamaha CRW4416S drive. Phillips Screwdriver Long nose pliers These are used to insert or remove the jumper pin when setting the SCSI ID and parity settings etc.of the Yamaha CRW4416S drive. Long nose pliers Discs ■ CD-R discs Please use discs that are compliant with Orange Book Part 2.
Chapter 2 - Installing the Yamaha CRW4416S Drive Chapter 2 - Installing the Yamaha CRW4416S Drive CRW4416S drive settings Before installing the CRW4416S in your computer, you will need to set the following jumpers. • SCSI ID settings • Parity setting • Terminator setting • Block size setting This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the CRW4416S drive. Important: Use long-nose pliers to remove or insert jumper connectors.
Chapter 2 - Installing the Yamaha CRW4416S Drive Note: When you are using Windows 95 or Windows 98, and if the SCSI ID setting on the rear panel is the same as the number assigned to another SCSI device, the Plug and Play component of Windows 95 or Windows 98 will automatically assign an unused number to the CRW4416S (SCAM protocol level 1).
Chapter 2 - Installing the Yamaha CRW4416S Drive ■ Terminator setting The terminator setting indicates whether or not this device is the last connected SCSI device. Terminator ON (with a jumper) — Use this setting if the CRW4416S is the last device in the internal SCSI daisy-chain. Terminator OFF (without a jumper) — Use this setting if devices other than the CRW4416S are in the internal SCSI daisy-chain and the CRW4416S is not the last device.
Chapter 2 - Installing the Yamaha CRW4416S Drive Installing the CRW4416S drive The following steps will differ slightly depending on the type of computer you are using. For details on removing the cover from your computer, and installing or removing internal devices, refer to the manual for your computer. (This user guide assumes that a SCSI card has already been installed.) 1. Switch off your computer, and unplug it from the AC outlet.
Chapter 2 - Installing the Yamaha CRW4416S Drive 3. Your hands or body may be holding a charge of static electricity. Touch a metallic portion of the chassis or power supply to release any such charge. 4. Remove the front cover of a vacant half-height drive bay. For details refer to the manual of your computer. 5. Remove the SCSI card, and set the terminator setting of the SCSI internal circuit to the position for internal connected devices. For details refer to the manual of your SCSI card. 6.
Chapter 2 - Installing the Yamaha CRW4416S Drive 7. Connect the SCSI flat cable. Connect the 50-pin SCSI flat cable to the SCSI card and to the SCSI interface located on the rear panel of the CRW4416S drive. Position the connector so that the colored line is at pin 1 (your lower right). PUT SCSI ACE DC IN RF INTE ECTOR +12V CONN G CT AUD IO O UT L RG 1 +5V ELE ID S Y IT PAR INATOR M TER K SIZE C BLO 124 8. Connect the AUDIO cable.
Chapter 2 - Installing the Yamaha CRW4416S Drive AUDIO cable To the CRW4416S 4-pin connector (large) To the Sound Card (Sound Blaster compatible) 4-pin connector (small) 9. Connect the power supply cable. Connect the +12V and +5V 4-pin power cable to the power supply interface located on the rear panel of the CRW4416S drive. The shape of the connector makes it impossible to reverse the connections.
Chapter 2 - Installing the Yamaha CRW4416S Drive 10. Tighten the four fastening screws securely. VOL ON/ DISC REA D/ WRITE 11. Attach the cover of your computer. 12. Connect the power cable to an AC outlet, and switch on your computer. Make sure that the LED located on the panel of the CRW4416S drive is lit. 13. Start up your operating system, and verify that the CRW4416S is recognized by the operating system. For the procedure, refer to the manual for your operation system. 14.
Chapter 3 - Operation Chapter 3 - Operation Front Panel 1 7 ON/ DISC 6 READ/ WRITE VOL 2 3 4 5 1 Disc tray The disc is inserted and ejected here. Pressing the eject button will open the tray. 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio. 3 Headphone volume control This control adjusts the volume level of the headphone output. Rotating the control clockwise will increase the volume level.
Chapter 3 - Operation 6 Eject button This button is used to open or close the tray. 7 Manual Eject hole This is used to manually eject a disc that cannot be ejected in the normal way. It is for emergency use only. Loading a Disc 1. Press the eject button to open the tray. 2. Carefully place the disc, label-side up, on the disc tray. 3. Press the eject button again to close the disc tray.
Chapter 3 - Operation Ejecting the Disc If the CRW4416S is powered on: Press the eject button to eject the disc. Note: You cannot eject the disc if the SCSI command prohibits the eject operation while the CRW4416S is reading data. Caution: Be sure to remove the disc after it is completely ejected. (Trying to remove the disc before it is completely ejected may cause the drive to malfunction.
Chapter 3 - Operation Manual Eject (emergency use) Here we explain how to eject the disc when it cannot be ejected in the normal way; for example, the power is shut off inadvertently or the loading mechanism fails. This technique should be used only as a last resort. Frequent use may lead to malfunction. You’ll need a pin-like object of 2 mm or less in diameter to do this. A straightened paper clip makes an ideal tool. 1. Insert the pin-like tool into the manual eject hole and push gently.
Troubleshooting Troubleshooting If CRW4416S is not performing as expected, look up the symptoms in the following table, and take the appropriate corrective action. Symptoms Corrective action The power to the CRW4416S is off • Check the DC power cable connection. The CRW4416S is not recognized by the computer • Check the SCSI cable connection. • Make sure that SCSI ID numbers are assigned exclusively. • Make sure that the last device in the SCSI daisy chain is terminated correctly.
Appendix Appendix Specifications Interface SCSI 2 Data Capacity 650MB (74 minutes disc) 550MB (63 minutes disc) Record/Read Speed Writing (CD-RW): 2X speed, 4X speed (when 4X compatible discs are used) Writing (CD-R): 1X speed (real-time), 2X speed, 4X speed playback: 9 - 16X speed [Max] (partial CAV) Note) Read CD-DA: 10X speed [Max] Read Video CD: 6X speed [Max] CD-DA output is 1X speed playback only Finalized Disc CD-R: 16X speed [Max] (packet writing is 10X speed [Max]) CD-RW: 6X speed [Max] (pack
Appendix Specifications are subject to change without prior notice.
English: If you have any questions, please contact your dealer or one of the following companies. French: Pour plus de détails sur les produits, veuillez vous adresser à Yamaha ou au distributeur le plus proche figurant dans la liste suivante : German: Bei weiteren Fragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden Firmen.