Service manual

ManualsBrandsYamaha ManualsCD PlayerCDS1000 - SACD Player

■ CONTENTS

TO SERVICE PERSONNEL ...................................... 2–3

PREVENTION OF ELECTROSTATIC DISCHARGE .... 4

FRONT PANEL .............................................................. 5

REAR PANELS .......................................................... 5–7

REMOTE CONTROL PANEL ........................................ 8

SPECIFICATIONS /

参考仕様...................................... 8–9

INTERNAL VIEW ........................................................... 9

DISASSEMBLY PROCEDURES / 分解手順 ........... 10–16

TEST MODE /

テストモード .......................................... 17

UPDATING FIRMWARE /

ファームウェアの書き込み

............................................................................ 18–24

DISPLAY DATA ........................................................... 25

IC DATA ................................................................. 26–28

PIN CONNECTION DIAGRAMS ............................ 29–30

BLOCK DIAGRAM ....................................................... 31

PRINTED CIRCUIT BOARDS................................ 32–40

SCHEMATIC DIAGRAMS ...................................... 41–45

REPLACEMENT PARTS LIST .............................. 47–56

REMOTE CONTROL.................................................... 57

101092

SERVICE MANUAL

SUPER AUDIO CD PLAYER

This manual is copyrighted by YAMAHA and may not be copied or

redistributed either in print or electronically without permission.

P.O.Box 1, Hamamatsu, Japan

'08.05

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.

It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already

known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal

injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,

we advise all YAMAHA product owners that any service required should be performed by an authorized

YAMAHA Retailer or the appointed service representative.

IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and

service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable

and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please

contact the distributor's Service Division.

WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

CD-S1000

Summary of content (57 pages)

PAGE 1
SUPER AUDIO CD PLAYER SERVICE MANUAL IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.
PAGE 2
CD-S1000 ■ TO SERVICE PERSONNEL WALL OUTLET CD-S1000 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. ● Meter impedance should be equivalent to 1500 ohms shunted by 0.15µF.
PAGE 3
CD-S1000 Laser Diode Properties Semiconductor laser (AlGaInP) Semiconductor laser (AlGaAs) • Laser Output: SA-CD CD CD-S1000 • Material: SA-CD CD • Wavelength: SA-CD CD 5 mW (max.) 7 mW (max.) 650 nm 780 nm CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG. VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
PAGE 4
CD-S1000 ■ PREVENTION OF ELECTROSTATIC DISCHARGE CD-S1000 Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1.
PAGE 5
CD-S1000 ■ FRONT PANEL CD-S1000 (U, C, R, T, K, A, B, G, L, J models) CD-S1000 ■ REAR PANELS CD-S1000 (U, C models) CD-S1000 (R model) 5
PAGE 6
CD-S1000 CD-S1000 CD-S1000 (T model) CD-S1000 (K model) CD-S1000 (A model) 6
PAGE 7
CD-S1000 CD-S1000 (B, G models) CD-S1000 CD-S1000 (L model) CD-S1000 (J model) 7
PAGE 8
CD-S1000 ■ REMOTE CONTROL PANEL CDX5 ■ SPECIFICATIONS / 参考仕様 ■ Audio Section / オーディオ部 CD-S1000 Frequency Response / 周波数特性 SA-CD .......................................................... 2 Hz to 50 kHz (-3 dB) CD ............................................................................. 2 Hz to 20 kHz Total Harmonic Distortion (1 kHz) / 高調波歪率（1 kHz） ................................................................................. 0.002 % or less Signal to Noise Ratio / 信号対雑音比 (IHF-A Network) ........
PAGE 9
14 440 (17-5/16") 418 (16-7/16") 137 (5-3/8") (11/16") 435 (17-1/8") 17 120 (4-3/4") (9/16") 362 (14-1/4") 371 (14-5/8") CD-S1000 8 • DIMENSIONS / 寸法図 (5/16") CD-S1000 Unit: mm (inch) 単位：mm（インチ） ■ INTERNAL VIEW 1 2 8 9 3 4 5 6 1 POWER TRANSFORMER 2 POWER (2) P.C.B. (R, L models) 3 POWER (1) P.C.B. 4 LOADER UNIT 5 AUDIO P.C.B. 6 DIGITAL (1) P.C.B. 7 DIGITAL (5) P.C.B. 8 POWER (3) P.C.B. 9 DIGITAL (4) P.C.B. 0 DIGITAL (3) P.C.B. A DIGITAL (2) P.C.B.
PAGE 10
CD-S1000 ■ DISASSEMBLY PROCEDURES / 分解手順（番号順に部品を取り外してください。） AC電源コンセントから、電源コードを抜いてください。 CD-S1000 (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Panel Side L/R 1. パネルサイド L/Rの外し方 a. Remove 2 screws (1), coned disc spring L and washer side. (Fig. 1) b. Lift the panel side L a little, release hooks at 3 locations and then remove the panel side L. (Fig. 1) c. Remove 2 screws (2) and then remove 2 washers. (Fig. 1) d.
PAGE 11
CD-S1000 3. フロントパネルの外し方 a. Using a flatblade screwdriver, move the slider at the bottom in the direction of the arrow shown below. (Fig. 2) a. マイナスドライバーで底面のスライダーを下図の矢印の方向に動かします。（Fig. 2） * CD-S1000 3. Removal of Front Panel ※ このとき、トレーは押し出されません。 Tray lock will be released but will not come out. b. トレイの後方を押し、トレイを押し出します。（Fig. 3） c. プラスドライバーで6のネジ2本を外し、リッドを取り外します。（Fig. 1） d. トレイの前方を押し、トレイを閉じます。 e. 7のネジ8本を外します。（Fig. 1） f. “POWER ON/OFF”スイッチをONにします。 g.
PAGE 12
CD-S1000 CD-S1000 4. Removal of Front Frame ass’y 4. フロントフレームASSYの外し方 a. Remove 4 screws (8), 2 screws (9) (B, G models) and then remove the frame top. (Fig. 4) b. Remove 9 screws (0). (Fig. 4) c. Remove CB601 and CB902. (Fig. 4) d. Remove the front frame ass’y. (Fig. 4) a. 8のネジ4本、9のネジ2本を外し、フレームトップを取り外します。（Fig. 4） b. 0のネジ9本を外します。（Fig. 4） c. CB601、CB902を外します。（Fig. 4） d. フロントフレームASSYを取り外します。（Fig. 4） 5. Removal of AUDIO P.C.B. 5. AUDIO P.C.B.の外し方 a. Remove 6 screws (A). (Fig. 4) b.
PAGE 13
CD-S1000 B Fig. 5 When checking the AUDIO P.C.B.: AUDIO P.C.B.をチェックをする場合には： • ・本機の上にゴムシートと布を敷き、その上にP.C.B.を裏返しに置いてチェックします。（Fig. 6）・外したケーブル（コネクター）をすべて接続します。ただし次の区間は、サービス用延長ケーブルを使用してください。 AUDIO P.C.B.：CB2ーDIGITAL P.C.B.：CB303 12P、450mm P=1.25（MF112450）・フラットケーブルを接続する際、極性に注意してください。・本機ではP.C.B.のアースがリアパネルおよびシャーシに接続されています。これらのP.C.B.をリアパネルより取り外した場合は、アース線等でアースポイントをリアパネルまたはシャーシに接続してください。（Fig. 6） • • • Put the rubber sheet and cloth over this unit. Then place the P.C.B.
PAGE 14
CD-S1000 7. Removal of DIGITAL P.C.B. 7. DIGITAL P.C.B.の外し方 a. Remove 3 screws (J). (Fig. 8) b. Remove 4 screws (K). (Fig. 9) c. Remove CB610-611 and CB901. (Fig. 8) a. b. c. d. d. Remove the DIGITAL P.C.B.. (Fig. 8) L R, L models Jのネジ3本を外します。（Fig. 8） Kのネジ4本を外します。（Fig. 9） CB610-611、CB901を外します。（Fig. 8） DIGITAL P.C.B.を取り外します。（Fig. 8） 8. POWER（1）P.C.B.の外し方 8. Removal of POWER (2) P.C.B. (R and L models) a. b. c. d. a. Remove 2 screws (L). (Fig. 9) b. Remove the POWER (2) P.C.B.. (Fig.
PAGE 15
CD-S1000 2. DVDトラバースメカおよびステッピングモーターの外し方 When installing a new DVD traverse mechanism, remove the solder from the shorted point of pick up unit using an electrostatic shielding soldering iron. ※ 新しいDVDトラバースメカに交換する場合、ピックアップユニットのショート箇所のハンダを静電気対策ハンダごてで取り除いてください。 a. Remove 6 screws (Q) and then remove the clamp ass’y. (Fig. 11) b. Push out the tray by pushing its rear. (Fig. 11) c. Remove 2 screws (R). (Fig. 11) d. Remove the DVD traverse mechanism together with the holder PU/SA-CD. (Fig. 11) e.
PAGE 16
CD-S1000 CD-S1000 • When installing a new Stepping Motor: Before installing a new stepping motor, apply grease to its screw. Recommended grease: PN-397 (Part No.: AAX89650) a. Apply grease to the screw at 3 points as shown below. (Fig. 12) * Amount of grease to be applied: 3mg ± 1mg at 3 points b. After applying grease, spread it evenly between A and B of the screw of the stepping motor. (Fig. 13) * While spreading grease evenly, use full care not to cause damage to the screw.
PAGE 17
CD-S1000 ■ TEST MODE / テストモード ● Starting Test Mode ● テストモード起動 "POWER ON/OFF" switch “POWER ON/OFF”スイッチ CD-S1000 To activate the TEST mode, set the “POWER ON/ OFF” switch to the ON position while pressing the keys of this unit as shown below at the same time. 本機の下図に示すキーを同時に押しながら“POWER ON/OFF”スイッチをONにすると、テストモードが起動します。 "PLAY" key “PLAY”キー "STOP" key “STOP”キー When the power is ON 電源オン時 Starting TEST mode テストモード起動 T E S T X0012 Release the “PLAY” and “STOP keys.
PAGE 18
CD-S1000 ■ UPDATING FIRMWARE / ファームウェアの書き込み CD-S1000 Writing to the microprocessor After replacing the following parts update the latest firmware according to the following procedure. DIGITAL P.C.B. Microprocessor (IC302) of DIGITAL P.C.B. ● Required tools 下記の部品を交換した場合、下記の手順により最新のファームウェアの書き込みを行ってください。 DIGITAL P.C.B. DIGITAL P.C.B.のマイコン（IC302） ● 必要なツール • Program downloader programs ................................................... FlashSta.exe ・プログラム書き込み用プログラム ...................................
PAGE 19
CD-S1000 ● 操作手順 1. Turn off the power of this unit and disconnect the power cable from the AC outlet. 1. 本機の電源を切り、電源コードをACコンセントから抜きます。 2. Remove 2 screws (1). (Fig. 1) 2. 1のネジ2本を外します。（Fig. 1） 3. Lift the panel side R a little, release hooks at 3 locations and then remove the panel side R. (Fig. 1) 3. パネルサイドRを少し持ち上げ、フック3ヶ所を外し、パネルサイドRを取り外します。（Fig. 1） 4.
PAGE 20
CD-S1000 CD-S1000 7. 7. Start up FlashSta.exe, the screen will appear as shown below. (Fig. 2) FlashSta.exeを立ち上げます。すると下記の画面が表示されます。（Fig. 2） Select Internal flash memory Internal flash memoryを選択します Select the port of RS-232C 接続しているRS-232Cポートを選択します Fig. 2 8. 9. 8. Select the port and data to be transmitted. (Fig.
PAGE 21
CD-S1000 CD-S1000 10.［E.P.R］をクリックすると、下記の画面が表示されます。（Fig. 4） 10. Click [E.P.R.], the screen appears as shown below. (Fig. 4) ［OK］をクリックし、書き込みを開始します。 Click [OK] to start writing. (Fig. 4) （Fig. 4） Writing being executed. 書き込み中 Fig. 4 11. プログラムの送信が終了すると、下記の画面が表示されます。（Fig. 5）［OK］をクリックして完了します。（Fig. 5） 11. When the program transmission is completed, the screen appears as shown below. (Fig. 5) Click [OK] to end the procedure. (Fig. 5) Fig.
PAGE 22
CD-S1000 CD-S1000 12. Set the “POWER ON/OFF” switch of this unit to the OFF position. 13. Disconnect the power cable of this unit from the AC outlet. 14. End “FlashSta. exe.” 15. Disconnect the RS232C cross cable, RS232C conversion jig and flexible flat cable. 12. 本機の “POWER ON/OFF” スイッチをOFFにします。 13. 本機の電源コードをACコンセントから抜きます。 14.“FlashSta.exe”を終了します。 15. RS232Cクロスケーブル、RS232C変換アダプターカード電線を取り外します。 • Confirmation of firmware version Confirm the firmware is updated successfully from the test mode.
PAGE 23
CD-S1000 モジュール基板への書き込み Writing to the Module Board モジュール基板をサービス部品に交換した場合、最新のファームウェアの書き込みを行ってください。 ● Required Tools ● 必要なツール CD-S1000 After replacing the Module board with the replacement part, be sure to write the latest firmware. ファームウェアCD ※ ファームウェアCDは、PCへ最新のファームウェアを指定のダウンロード先からダウンロードして制作してください。 Firmware CD * To make the firmware CD, download the latest firmware from the specified download source to PC. Firmware: S5JAxxx6.BIN ファームウェア：S5JAxxx6.
PAGE 24
CD-S1000 CD-S1000 6. 7. 8. 6. 約5秒後、自動でトレイが開きます。ファームウェアCDを取り出します。 ※ このとき、本機はファームウェアの書き込みを継続しています。電源は切らないでください。 ※ 書き込み時間は、約1分間ほどかかります。 7. 書き込み終了後、トレイが自動で閉じます。 8. “NO DISC” と表示された後、 “POWER ON/OFF” スイッチをOFFにします。 After about 5 seconds, the tray opens automatically. Remove the firmware CD. * At this time, do not turn off the power as writing of the firmware is going on in this unit. * Writing takes about 1 minute. When writing is completed, the tray closes automatically.
PAGE 25
CD-S1000 ■ DISPLAY DATA ● V800 : 13-ST-81GINK (DIGITAL (2) P.C.B.) CD-S1000 43 1 ● PIN CONNECTION Pin No. 19 18 17 16 15 14 13 12 11 10 9 8 7 6 Connection NX NX NX NX NX NX NX NX NX NX NX NX NX NX Pin No. 37 36 34 33 32 Connection VDD OSC RESET CS CP DA 39 38 35 Pin No.
PAGE 26
CD-S1000 ■ IC DATA CD-S1000 IC302: M30302FAPFP (DIGITAL (1) P.C.B.
PAGE 27
CD-S1000 Port Name P9_6/ANEX1 P9_5/ANEX0 P9_4 P9_3 P9_2/TB2IN P9_1/TB1IN P9_0/TB0IN BYTE CNVSS P8_7/XCIN P8_6/XCOUT /RESET XOUT VSS XIN VCC1 P8_5/NMI P8_4/INT2 P8_3/INT1 P8_2/INT0 P8_1 P8_0 P7_7 P7_6 P7_5/TA2IN P7_4/TA2OUT P7_3/CTS2/RTS2/TA1IN P7_2/CLK2/TA1OUT P7_1/RXD2/SCL2/TA0IN P7_0/TXD2/SDA2/TA0OUT P6_7/TXD1/SDA1 P6_6/RXD1/SCL1 P6_5/CLK1 P6_4/CTS1/RTS1/CTS0/CLKS1 P6_3/TXD0/SDA0 P6_2/RXD0/SCL0 P6_1/CLK0 P6_0/CTS0/RTS0 P5_7/RDY/CLKOUT P5_6/ALE P5_5/HOLD P5_4/HLDA P5_3/BCLK P5_2/RD P5_1/WRH/BHE P5_0/WRL/W
PAGE 28
CD-S1000 CD-S1000 No.
PAGE 29
CD-S1000 ■ PIN CONNECTION DIAGRAMS • ICs BD4829G-TR CD-S1000 BA08CC0T LME49723MA LB1641 4 5 8 10 3 4 1 1 1 1 3 M30302FAPFP NJM78L12UA NJM7808FA NE5532DR 80 51 50 81 4 8 100 1 31 1 1 1 2 30 PCM1796DBR NJM78M05FA PQ033ES3MXP 3 1: INPUT 2: GND 3: OUTPUT TC74VHC08F 2 1: OUTPUT 2: GND 3: INPUT 3 TC74HCT08AF 14 7 28 14 3: OUT 1: IN 2: GND 1 1 5 4 8 3 4 16 1 1 1 TC7WU04F 5 8 1 3 TC7SH08F TS7ST00F TC74VHC157F 7 14 1 • Diodes 1SS355 MA8030 3.0V MA8047-H 4.
PAGE 30
CD-S1000 CD-S1000 • Transistors 2SA1037K 2SA2168 2SC5291 C C C E B 2SD2014 SCA1725 2SC4511 E E E B CB E 2SK208-Y CE B KTC3198 3 D B CB DTA114EKA DTC114EKA G 30 2SA1312-GR,BL 2SD1938F 2SC3324-GR,BL 2SC2878 2SC2412K S 1 2 1: GND 2: IN 3: OUT B CE
PAGE 31
A B C D E F G H I J CD-S1000 1 ■ BLOCK DIAGRAM AUDIO MODULE BOARD IC14 IC19, 20 IC1 2 6 PCM1792ADBR 7 17 5 7 6 2 • See page 44 → SCHEMATIC DIAGRAM NE5532DR AUDIO IC15 1 3 18 7 2 IC10 NE5532DR Q9, 15 PJ1 3 IC21, 22 IC4 IC16 LOADER UNIT IC304 IC303 6 PCM1792ADBR 5 6 7 NE5532DR 2 4 7 17 AUDIO IC17 1 18 3 2 7 NE5532DR Q12, 18 PJ4 MUTE POWER 2-7 +B IC302 POWER TRANSFORMER D603 5 DOUT C622 MICROPROCESSOR D602 U301 CLAMP/TRAY PJ301 M30302FAPFP 23-26
PAGE 32
A B C D E F G H I J CD-S1000 1 ■ PRINTED CIRCUIT BOARDS DIGITAL (1) P.C.B. (Side A) • Semiconductor Location Ref no. Location Ref no. Location IC303 F5 IC304 G5 Writing port 2 CB308 3 DIGITAL (5) (CB901) KEY1 KEY2 +5 LED_POWER IR KEY0 +3.
PAGE 33
A B C D E F G H I J CD-S1000 1 DIGITAL (1) P.C.B. (Side B) 2 4 1 3 IC305 5 POINT A-1 XL301 (Pin 13 of IC302) 8 7 7 8 IC306 1 IC308 14 3 1 31 30 14 1 A-2 2 51 2 30 IC 50 A-1 1 100 4 1 IC307 4 80 81 5 8 POINT A-2 1 / Pin 16, 2 / Pin 12 of IC302 5 IC302 1 16 pin IC302 2 12 pin 3 AC cable ON AC cable OFF 1 IC301 2 5 6 • Semiconductor Location IC302 1 16 pin Ref no. Location Ref no.
PAGE 34
A B C D E F G H I J CD-S1000 1 • Semiconductor Location Ref no. Location Ref no. Location C6 D6 D803 G2 KEY0 +3.3 IR +5 LED_PDIRECT +30 LED_SACD ACFL2 ACFL1 FLGND FLGND D801 D802 DIGITAL (4) P.C.B. (Side A) DIGITAL (6) P.C.B. (Side A) POWER indicator W803B LED_POWER KEY2 FL_DATA FL_CS DGND FL_CLK 2 KEY1 DGND FL_RESET DIGITAL (2) P.C.B. (Side A) CB800 LED_POWER +5 3 DIGITAL (5) P.C.B. (Side A) +3.
PAGE 35
A B C D E F G H I J CD-S1000 1 DIGITAL (2) P.C.B. (Side B) DIGITAL (4) P.C.B. (Side B) DIGITAL (6) P.C.B. (Side B) 2 3 DIGITAL (5) P.C.B. (Side B) 4 5 DIGITAL (3) P.C.B. (Side B) 6 1 3 5 IC802 4 • Semiconductor Location Ref no. Location Ref no.
PAGE 36
A B C D E F G H I J CD-S1000 1 2 DGND XCS01 SD BCLK/DSDCLK R_DATA DATA/L_DATA LRCK MCLK MODULE board DSDPCM XCS02 SCL GNDD GNDD GNDD GNDD GNDD GNDD AUDIO P.C.B.
PAGE 37
A B C D E F G H I J CD-S1000 1 • Semiconductor Location Ref no. Location 2 D1 I4 D2 D3 I4 I5 D4 Q2 I5 H6 Q3 Q9 H6 C4 Q12 Q15 C5 C4 Q18 C5 AUDIO P.C.B.
PAGE 38
A B C D E F G H I J CD-S1000 1 DIGITAL (1) (W306) POWER (1) P.C.B. (Side A) POWER TRANSFORMER DGND +8 +12 ACFL1 ACFL2 +8M 2 AC IN MGND VCC IC661 GND OUT CB613 CB610 OUT COM IC603 COM OUT CB611 3 IN IC605 DGND +5 +3.
PAGE 39
A B C D E F G H I J CD-S1000 1 POWER (1) P.C.B. (Side B) 2 3 OUT IN CON IC606 4 5 6 • Semiconductor Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no.
PAGE 40
A B C D E F G H I CD-S1000 1 POWER (2) P.C.B. (Side A) POWER (3) P.C.B. (Side A) R, L models VOLTAGE SELECTOR 2 POWER (1) (W606A, W606B) 1 2 220V 120V 230240V 110V CB601 4 3 P 3 W603B W602B W605B W604B W601B POWER ON/OFF switch CB615 POWER (1) (W601A, W602A, W603A, W604A, W605A) 4 POWER (2) P.C.B. (Side B) R, L models 5 6 7 40 POWER (3) P.C.B.
PAGE 41
A B C D E F G H I J L K M N CD-S1000 SCHEMATIC DIAGRAMS DIGITAL 1/3 1 CB301 W306 Page 45 M7 to POWER (1)_CB610 3.3 3.3 3.3 3.3 0 3.3 To MODULE board 3.3 3.3 0 0 3.3 2 0 IC308 3 12 5.0 3.3 11 13 3.3 0.5 5.0 5.0 MICROPROCESSOR 1.7 2.5 0.5 IC306 3.3 0 2 3.3 4 3.3 3.3 IC302 5 0 IC3065.0 5 3.3 9 3.3 4 3.3 3.3 0 0 A-2 0 A-1 3.3 3.3 3.3 11 13 3.3 3.3 CB302 8 3.3 IC3065.0 3.3 2 1 3.3 12 3.3 10 IC308 5.0 8 10 3.3 3.3 0 9 3.
PAGE 42
A B C D E F G H I J L K M N CD-S1000 DIGITAL 2/3 1 2 5.3 0 0 5.0 30.3 3.4 5.3 5.0 5.0 30.3 3 0 0.6 0.8 0 5.3 5.0 DIGITAL (2) 30.3 0.6 0.8 CB800 0 4 Page 43 H4 to DIGITAL (5)_CB902 CB802 W801 W803A W803B 5 5.0 5.0 3.3 3.6 1.9 0.1 SAN-PH 0 3.3 0 0 0.1 0 0 6 DIGITAL (4) 7 8 + 3.3 k + 12.0 k 0.6 – 1.0 1.6 – 2.0 PAUSE OPEN/CLOSE SEARCH+/SKIP+ SEARCH-/SKIPSA-CD/CD – 3.3 IC802 3.3 3.
PAGE 43
A B C D E F G H I J K L M N CD-S1000 DIGITAL 3/3 1 2 DIGITAL (5) 3 CB901 CB902 4 Page 42 B4 to DIGITAL (2)_CB800 Page 41 5 L4 to DIGITAL (1)_CB307 6 CB903 7 To LOADER unit 8 9 10 ★ All voltages are measured with a 10MΩ/V DC electronic voltmeter. ★ Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. ★ Schematic diagram is subject to change without notice.
PAGE 44
A B C D E F G H I J L K M N CD-S1000 AUDIO 1 12.2 5.1 IC11 12.2 12.0 12.2 5.1 6.3 -0.6 3.4 0 6.3 BUFFER AMP 6.3 CB5 2 Page 45 0 0 J2 0 to POWER (1)_CB608 12.0 IC19 -5.1 11.9 IC14 -1.0 0 12.0 0 0 OUT L 0 0 0 IC15 0 0 0 IC15 -12.2 ANALOG OUT L 0 0.6 -12.2 5.1 0 -12.3 1.7 0 0 IC19 0 -5.1 0 0 1.3 0 0 0 IC1 CD IN -12.2 0 -12.3 0 0 -12.2 5.1 1.7 1.6 -12.1 2.3 0 0 2.3 2.5 3 3.4 0 3.4 0 3.4 0 3.4 1 1.3 0 IC12 5.1 1.3 3.
PAGE 45
A B C D E F G H I J L K M N CD-S1000 POWER 1 17.1 15.0 14.4 14.4 0 -17.0 12.2 5.1 17.1 5.7 0 0 CB608 2 Page 44 B2 to AUDIO_CB5 0 -5.5 -5.0 POWER (2) R, L models -14.4 -12.3 R, L models -14.4 -15.0 CB606 -17.0 3 R, L models W604B W604A W601B W601A W605B W605A W603B W603A W602B W602A CB604 17.1 14.8 AC26.9 14.4 14.4 0 11.9 5.6 -17.0 17.1 5.0 5.6 VOLTAGE SELECTOR 0 CB603 4 CB609 0 POWER TRANSFORMER Page 44 B8 to AUDIO_CB6 0 -5.5 -4.9 -5.5 -12.
PAGE 46
CD-S1000 ■ REPLACEMENT PARTS LIST • ELECTRICAL COMPONENT PARTS CD-S1000 WARNING ● Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. ● The chip resistor is not supplied as a replacement part. * When a chip resistor is necessary, use the following part.
PAGE 47
CD-S1000 CD-S1000 P.C.B. DIGITAL * Ref No. Part No.
PAGE 48
CD-S1000 P.C.B. DIGITAL and P.C.B. AUDIO Part No.
PAGE 49
CD-S1000 CD-S1000 P.C.B. AUDIO * * * * Ref No. Part No.
PAGE 50
CD-S1000 P.C.B. AUDIO Part No.
PAGE 51
CD-S1000 CD-S1000 P.C.B. AUDIO and P.C.B. POWER * * * * * * Ref No. Part No. R162-165 ST1-2 ST1-2 HL006100 R.MTL.OXD WG095100 SCR.TERM V4040500 SCR.
PAGE 52
CD-S1000 P.C.B. POWER * * Ref No. Part No.
PAGE 53
A B C D E F G H I J CD-S1000 1 • OVERALL ASS’Y 166 166 166 200 166 103 171 162 166 43 2 R, L models 10 (2) 156 166 U, C models 200-1 155 166 202 100 164 166 43 166 Loader Unit 3 164 165 203 157 158 164 4-2 4-3 163 165 40 17 170 161 165 42 163 4 165 165 164 4 (L) 166 22 154 12 43 41 103 165 160 140 166 10 (1) 151 111 165 111 164 170 15 15-6 164 10 (3) 37 11 (1) 169 5 11 (4) 24 164 15-7 165 153 166 1-12 1-13 1-15 (2) 21 11 (5) 11 (
PAGE 54
CD-S1000 * * * * * * * * * * * * * * * * * * * * * * * * * * * s s s s s s Ref No. Part No.
PAGE 55
A B C D E F G H I J CD-S1000 1 • LOADER UNIT Ref No. Part No.
PAGE 56
CD-S1000 ■ REMOTE CONTROL • SCHEMATIC DIAGRAM • PANEL • KEY LAYOUT • KEY CODE VDD No. R1 1 3.3 ohms C1 + C4 47uF/10V 0.1uF IR-LED IR1 U1 SC73P1601 1 2 GND P50 VDD P53 20 4 C2 C3 X1 3.
PAGE 57
CD-S1000