UAB CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER APPART PRODUIT LASER DE CLASSE 1 ACHTUNG Die Verwendung von Bedienungselementen oder Einstellungen oder die Durchführung von Bedienungsvorgängen, die nicht in dieser Anleitung aufgeführt sind, kann zu einem Kontakt mit gefährlichen Laserstrahlen führen.
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical Symbols 1 2 3 4 5 6 7 Read these instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
FCC INFORMATION (for US customers) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT • To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. • Install this unit in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/ or cold. Avoid ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 10 cm on the back of this unit.
Hard Disk Drive (HDD) ■ Before using • If you purchase CDR-HD1300; this model is not equipped with a hard disk drive (HDD). Please purchase a commercially available HDD for internal use and install it on this unit correctly, following the attached instruction. • It is necessary to format a new HDD after installation. Also refer the attached instruction for formatting. • If you purchase CDR-HD1300E; this model is equipped with an HDD.
About This Manual ■ Structure ■ About this manual This owner’s manual is composed of following sections. • This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement in operativity ability, and others. In this case, the product has priority. • Some of the illustrations and names of the package contents etc written in this manual may differ from the actual products and the names written on the package etc.
Contents GETTING STARTED DUPLICATION OF A CD SUPPLIED ACCESSORIES ............................................ 2 CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT ........ 3 RULES OF DIGITAL RECORDING AND NOTES ON SYSTEM ...................................................................... 5 Rules of Digital Recording .................................................... 5 Notes on System .................................................................... 5 Data on the HDD .........................................
SUPPLIED ACCESSORIES Make sure the following items are included in your package. • Remote Control • Batteries (size AA, UM-3, or R6) (2) OPEN/CLOSE COPY TIMER REC A.M.Q.R. FINALIZE TEXT/TIME INPUT MODE REC ERASE • Audio Pin Cables (2) TRACK NO. WRITE MENU COMPLETE CLEAR ENTER 1 ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO • Optical Cable GROUP SKIP HDD CDR • Video Pin Cable • Power Cable (for U.S.A.
CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT ■ Discs that can be used for recording on this unit FOR CONSUMER FOR CONSUMER USE FOR MUSIC USE ONLY ■ Discs that can be used for recording • CD-R discs can only be recorded on once, and the recorded material cannot be erased. • CD-RW discs can be recorded on, have the recorded material erased, and then recorded on again any number of times. ■ Discs that cannot be used for recording on this unit • Discs bearing marks other than those shown above.
CD/CD-R/CD-RW COMPATIBLE WITH THIS UNIT ■ Handling of discs ■ To prevent a malfunction of this unit Heed the following notes on handling of discs not to create any cause for a recording failure, a loss of the recorded data, or a malfunction of this unit. • Do not use any non-standard shaped CDs (heart, flower shaped, etc.) available on the market, because they are off-balance in their weight.
RULES OF DIGITAL RECORDING AND NOTES ON SYSTEM Notes on System ■ SCMS—Serial Copy Management System ■ Number of recordable discs and tracks and their length As a digital audio component, this unit conforms with the Serial Copy Management System (SCMS) standards. The Serial Copy Management System restricts copies made by recording digital signals to first-generation copies only. The digital program sources that have been recorded cannot be digitally recorded again.
RULES OF DIGITAL RECORDING AND NOTES ON SYSTEM Data on the HDD The data recorded onto the built-in HDD of this unit will be numbered and organized based on the following concept: Disc One consequent recording is counted and numbered as one unit of disc. The HDD of this unit can record 999 discs at maximum. (However, the number of discs to be created may be less than 999 for the space availability on the HDD.) The maximum length of one disc on the HDD is 99minutes 59 seconds.
NAMES OF BUTTONS AND CONTROLS Front Panel 4 5 6 789 0 q GETTING STARTED 2 3 1 w er MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE TRACK NO. COMPLETE MENU POWER CLEAR BOOKMARK DIGITAL REC LEVEL HDD PHONES CDR COPY LEVEL INPUT REC FINALIZE ERASE A.M.Q.R. ANALOG REC LEVEL OPTICAL COAXIAL ANALOG MIN t MIN MAX u y MAX i o p as d f g h 1 POWER r CLEAR 2 HDD t PHONES jack 3 CDR y PHONES LEVEL control 4 COPY u A.M.Q.R.
NAMES OF BUTTONS AND CONTROLS Remote Control 1 2 3 4 5 6 COPY TIMER REC A.M.Q.R. FINALIZE TEXT/TIME INPUT MODE REC ERASE TRACK NO. WRITE MENU COMPLETE q w e CLEAR 1 ABC ENTER 2 DEF 3 COPY 3 TIMER REC i 4 A.M.Q.R.
NAMES OF BUTTONS AND CONTROLS ■ Loading the batteries in the remote control ■ Remote control operation range 1. Remove the battery compartment cover on the back of the remote control. MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE TRACK NO. COMPLETE MENU POWER CLEAR GETTING STARTED BOOKMARK DIGITAL REC LEVEL 2. Insert 2 batteries (AA, UM-3 or R6 type) according to HDD PHONES CDR COPY LEVEL INPUT REC A.M.Q.R.
NAMES OF BUTTONS AND CONTROLS Display 1 2 3 4 5 6 8888888888888 ALBM TOTAL DUPLCT A.M.Q.R. AUTO PRD DIG M MARK S G A REP RNDM MULT ALL SYNC ANLG 8 9 0 q L dB –30 –10 w q –6 –2 0 R e 1 HDD mark 2 TOTAL indicator 3 DUPLCT indicator 4 A.M.Q.R.
NAMES OF BUTTONS AND CONTROLS Display Information ■ Display while playing the data on the HDD ■ Display while playing a CD Group number, track number and elapsed time of the track being played Track number and elapsed time of the track being played 1 Dsc001 1 004 004 L dB G –30 –10 –6 –2 0 L dB –30 –10 –6 –2 0 R TOC GROUP CD GROUP R Group number, track number and remaining time of the track being played GETTING STARTED The display located in the center of this unit provides the info
NAMES OF BUTTONS AND CONTROLS Rear Panel 1 2 3 VIDEO OUT S VIDEO VIDEO L L R R 4 REC PLAY 3 COAXIAL LINE IN — LINE OUT OPTICAL COAXIAL IN ANALOG OPTICAL OUT RS–232C DIGITAL 4 5 6 (U.S.A.
CONNECTIONS ■ Connecting a monitor • Arrow marks (➞) in the illustration below indicate the direction of the audio signal. Monitor DVD player, cable TV tuner, etc Coaxial cable (optional) DIGITAL OUTPUT GETTING STARTED • You can display the list of groups or tracks to be played, copying/recording settings or the list of setting items on the monitor by connecting the monitor to this unit. Connect the S VIDEO jack or the VIDEO jack whichever available on your monitor.
COPYING FROM A CD ONTO THE HDD Copying All Tracks on a CD You can copy all tracks on a CD onto the HDD. 2,4 5 3 2,4 5 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ OPEN/CLOSE COPY TIMER REC A.M.Q.R. FINALIZE +10 0 SPACE SYMBOL BOOKMARK REPEAT RANDOM INTRO REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT TRACK NO.
COPYING FROM A CD ONTO THE HDD 5. Press COPY once. The following message appears on the display, and this unit enters the copy standby mode. Copying has not been started yet at this stage. HDD π CD-RW DIG dB –30 –10 –6 –2 0 R 003 1π 1 DIG ALL SYNC 000 L dB –30 –10 –6 –2 0 R REC TOC GROUP CD REC TOC GROUP CD 6. Start copying.
COPYING FROM A CD ONTO THE HDD Copying Favorite Tracks on the CD You can copy your favorite tracks on a CD onto the HDD. 1 5 1 1 3,6 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ OPEN/CLOSE COPY 5 TIMER REC A.M.Q.R. FINALIZE +10 0 SPACE SYMBOL BOOKMARK REPEAT RANDOM INTRO REC 3,6 ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT TRACK NO.
COPYING FROM A CD ONTO THE HDD Advanced Operations ■ Making an additional copying onto an already recorded disc MULTI JOG ■ Setting the copying mode This unit provides various copying modes. Choose the one that suits your needs. PUSH ENTER TEXT/TIME MODE TRACK NO. COMPLETE MENU MODE MULTI JOG CLEAR BOOKMARK MULTI JOG ER DIGITAL REC LEVEL PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR COPY INPUT FINALIZE REC ERASE ANALOG REC LEVEL OPTICAL A.M.Q.R.
COPYING FROM A CD ONTO THE HDD 3. Press the MULTI JOG knob (ENTER on the remote control) to confirm the copying mode selected. If “All Synchro” is confirmed, this unit returns to the copy standby mode. If “Multi Synchro” is confirmed, the following message appears on the display. Go to step 4. How many ? DIG MULT SYNC 1 L dB R –30 –10 –6 –2 0 ■ Copying menu setting You can make detailed settings on the menu for your copying. Follow the steps described below for menu setting.
COPYING FROM A CD ONTO THE HDD ■ Copy Method 2. Press the MULTI JOG knob (ENTER on the remote Setting of the copying method. Copying may fail if the setting for “Copy Method” is not correctly made. Copy Method REC L DIG dB ALL SYNC –30 –10 –6 –2 0 R TOC CD Digital Copy This method always makes digital copies. Copying is not possible if the tracks are copy protected by the SCMS standard (see page 5). Auto Dig/Anlg Digital and analog copying are automatically switched depending on the track.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD Recording from the Digital Components You can make recordings from the component such as a cable TV tuner and a DVD player digitally connected to this unit. Note • Recording onto the HDD is made in the unit called “disc”. The maximum length of one disc on the HDD is 99 minutes 59 seconds. If the recording has been made exceeding the maximum length, the recording will be made continuously to the next available disc.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD Recording from the Analog Components You can make recordings from the component such as a cassette deck and a turntable connected to this unit. 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE 6 COPY 3 TIMER REC A.M.Q.R. FINALIZE REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR POWER TEXT/TIME 4 INPUT MODE TRACK NO.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD Recording Using an External Timer ■ Notes on recording time setting • This unit is not equipped with the clock function. Use an external timer when making a timer recording. • It may take 30 seconds to 1 minute after the power of this unit is turned on by an external timer until an actual recording starts. (This length of time is subject to change depending on the condition.) During this time, no recording is made.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD ■ Setting for a timer recording 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR POWER BOOKMARK DIGITAL REC LEVEL PHONES CDR COPY LEVEL INPUT REC FINALIZE ERASE A.M.Q.R. ANALOG REC LEVEL OPTICAL COAXIAL ANALOG MIN MIN MAX 1 TIMER REC REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER HDD COPY A.M.Q.R.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD Adjusting the Recording Level There is an adjusting procedure for each input source to be recorded as explained below. Choose the one for your input source and follow the steps. OPEN/CLOSE COPY MULTI JOG TIMER REC REC MENU A.M.Q.R. FINALIZE ERASE MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT MODE TRACK NO.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD Advanced Operations ■ Making an additional recording onto an already recorded disc MULTI JOG ■ Setting the recording mode This unit provides various recording modes. Choose the one that suits your needs. PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR MODE MULTI JOG MULTI JOG ER BOOKMARK PUSH ENTER DIGITAL REC LEVEL TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR COPY INPUT FINALIZE REC ERASE ANALOG REC LEVEL OPTICAL A.M.Q.R.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD 3. Press the MULTI JOG knob (ENTER on the remote control) to confirm the recording mode selected. If “Manual”, “Track Synchro” or “All Synchro” is confirmed, this unit returns the recording pause mode. If “Multi Synchro” is confirmed, following message appears on the display. Make a setting following steps 4 and 5. How many ? 1 SYNC dB –30 –10 –6 –2 0 R If “Auto Period” is confirmed, following message appears on the display.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD ■ Setting a condition for synchronized recording MULTI JOG MENU control) to adjust the level. Level can be set by 1dB step. Example: To set “ANLG TH Level” MULTI JOG ER 6. Rotate the MULTI JOG knob (press +/– on the remote PUSH ENTER TEXT/TIME MODE TRACK NO. COMPLETE MENU CLEAR ANLG TH -40dB LEVEL DIGITAL REC LEVEL dB –30 –10 –6 –2 0 R COPY INPUT FINALIZE REC ERASE ANALOG REC LEVEL OPTICAL A.M.Q.R. COAXIAL ANALOG MIN MAX 7.
RECORDING FROM AN EXTERNAL COMPONENT ONTO THE HDD ■ Manual track marking OPEN/CLOSE TRACK NO./BOOKMARK COPY TIMER REC REC MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU A.M.Q.R. FINALIZE TRACK NO. COMPLETE ERASE CLEAR TEXT/TIME BOOKMARK INPUT TRACK NO. WRITE DIGITAL REC LEVEL COPY MODE INPUT REC A.M.Q.R. FINALIZE ERASE MENU ANALOG REC LEVEL COAXIAL ANALOG MIN MAX COMPLETE CLEAR 1 This unit can automatically place track markers.
EDITING MENU ITEMS You can make various editing operations on the albums, tracks and discs on the HDD. The editing menu is listed below. Menu item Album Edit Disc Edit Album New Edit Stored Album Copy Album Rename Album Delete Album Pack Album Title Track Shuffle Track Level Tr.
ALBUM EDITING You can select the desired tracks from among the ones recorded on the HDD and store them as an album in this unit’s memory. You can also edit the album afterwards. Album Editing Operation 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE MULTI JOG COPY MENU TIMER REC A.M.Q.R. FINALIZE REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT TRACK NO.
ALBUM EDITING Album New Edit Stored You can create a new album by selecting the desired tracks from among the ones recorded on the HDD. You can add tracks to or delete tracks from an already created album. 1. Select and confirm “Album New” in step 4 of “Editing 1. Select and confirm “Edit Stored” in step 4 of “Editing during the stop mode” on page 30. The following message appears on the display. Source disc during the stop mode” on page 30. The following message appears on the display.
ALBUM EDITING 7. Select the track to be added by rotating the MULTI JOG knob (pressing +/– on the remote control). 8. Press the MULTI JOG knob (ENTER on the remote control) to confirm the track to be added. When continuing to add tracks to the album, repeat steps 4—8. 9. Press COMPLETE. The selected tracks are added to the album. This unit returns to the editing menu item selection. Album Copy You can copy the entire disc, album, or bookmark to a new album. 1.
ALBUM EDITING Album Rename Album Delete You can move the album and assign a new number. You can delete an existing album. 1. Select and confirm “Album Rename” in step 4 of ■ Editing during the stop mode “Editing during the stop mode” on page 30. The following message appears on the display. Rename “Editing during the stop mode” on page 30. The following message appears on the display. 001? L dB –30 –10 –6 –2 0 1.
ALBUM EDITING 3. Press the MULTI JOG knob (ENTER on the remote Album Pack You can re-organize the album numbers by eliminating unused album numbers that have been created by changing album numbers or deleting albums. control) to confirm the album to assign a title to. The following message appears on the display. L dB 1. Select and confirm “Album Pack” in step 4 of “Editing during the stop mode” on page 30. The following message appears on the display. –6 –2 2. Press COMPLETE.
ALBUM EDITING ■ Entering the title characters by using the MULTI JOG knob Track Shuffle 1. Rotate the MULTI JOG knob clockwise. You can change the order of tracks in an album. When the MULTI JOG knob is rotated clockwise, characters appear in the order of alphabetical capital letters, alphabetical lower case letters, numbers, and symbols. Select the character you wish to use for the title. 2.
ALBUM EDITING 6. Rotate the MULTI JOG knob (press +/– on the remote control) to select the new track number. 7. Press the MULTI JOG knob (ENTER on the remote control) to confirm the new track number. Press CLEAR to cancel the confirmed selection. Track Level You can adjust the sound level of track in an album. ■ Editing during the stop mode 1. Select and confirm “Track Level” in step 4 of “Editing 8. Press COMPLETE. The selected track has been moved and assigned a new number.
ALBUM EDITING 6. Rotate the MULTI JOG knob (press +/– on the remote control) to adjust the level. Adjustment is possible in the –12dB to +12dB range by 0.4dB steps. You can compare the level with the previous or next tracks’ level by pressing t/e or r/y (t or y on the remote control). You can also search the passage in the selected track by pressing and holding t/e or r/y (e or r on the remote control). The level of the selected track is confirmed. This unit returns to the editing menu item selection.
ALBUM EDITING 6. Rotate the MULTI JOG knob (press +/– on the remote Tr. Interval control) to adjust the interval. Adjustment is possible in the 0 to 9.9 seconds range by 0.1second steps. You can adjust each track interval in an album. ■ Editing during the stop mode 1. Select and confirm “Tr. Interval” in step 4 of “Editing during the stop mode” on page 30. The following message appears on the display. Track to adjust its interval between the previous track Int.
TRACK EDITING You can do various editing operations on the tracks that have been recorded on the HDD. Track Editing Operation 4 JKL 5 MNO 7 6 PQR 9 YZ STU 8 VWX 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE MULTI JOG COPY MENU TIMER REC A.M.Q.R. FINALIZE REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER MODE MENU COMPLETE CLEAR TEXT/TIME INPUT TRACK NO.
TRACK EDITING 7. Press the MULTI JOG knob (ENTER on the remote Track Rename control) to confirm the new track number. Press CLEAR to cancel the confirmed selection. You can move a track and assign a new number. 8. Press COMPLETE. ■ Editing during the stop mode 1. Select and confirm “Track Rename” in step 5 of “Editing during the stop mode” on page 39. The following message appears on the display.
TRACK EDITING 6. Adjust the time length to change the beginning of the Track Adjust You can change the beginning of the track to either earlier or later. ■ Editing during the stop mode 1. Select and confirm “Track Adjust” in step 5 of “Editing during the stop mode” on page 39. The following message appears on the display. Disc that contains the track to be adjusted L dB –30 –10 –6 –2 0 GROUP R Press CLEAR to cancel the adjustment. 7. Press COMPLETE.
TRACK EDITING 3. Press COMPLETE. 5. Press the MULTI JOG knob (ENTER on the remote The new track beginning point is set. Playback resumes from the beginning of the adjusted track. Before “Track Adjust” is performed 1 control) to confirm the track to be erased. Press CLEAR to cancel the confirmed selection. To check the track to be erased, press w/d (w on the remote control). This unit starts to play the track to be erased repeatedly. 2 6. Press COMPLETE. 1 The selected track is erased.
TRACK EDITING 7. Press MULTI JOG knob (ENTER on the remote Part Erase You can erase part of a selected track. ■ Editing during the stop mode 1. Select and confirm “Part Erase” in step 5 of the “Editing during the stop mode” on page 39. The following message appears on the display. Disc that contains the track to be partially erased control) to confirm the beginning point of the partial erase.
TRACK EDITING ■ Editing during playback 5. Press MULTI JOG knob (ENTER on the remote 1. Select and confirm “Part Erase” in step 2 of “Editing during playback” on page 39. The track being played is confirmed to be partially erased. The passage between the point that is 5 seconds before the beginning point of the partial erase and the beginning point (the timing you press MENU) is repeatedly played. The following message appears on the display. control) to confirm the ending point of the partial erase.
TRACK EDITING 6. Select the track to be the last in the combination by Track Combine rotating the MULTI JOG knob (pressing +/– on the remote control). You can combine a series of tracks into one. 7. Press the MULTI JOG knob (ENTER on the remote ■ Editing during the stop mode 1. Select and confirm “Track Combine” in step 5 of “Editing during the stop mode” on page 39. The following message appears on the display.
TRACK EDITING 6. Set the dividing point by rotating the MULTI JOG Track Divide knob (pressing +/– on the remote control). The dividing point can be set by “minute: second: frame”. The unit to be set is flashing. Move the flash to the unit to be set by pressing t/e or r/y. You can divide a track into two at the selected point. ■ Editing during the stop mode 1. Select and confirm “Track Divide” in step 5 of “Editing during the stop mode” on page 39. The following message appears on the display.
TRACK EDITING 3. Press COMPLETE. The track being played is divided into two at the set dividing point. Playback resumes from the beginning of the second track of the two divided tracks. You can re-organize the track numbers by eliminating unused track numbers, that have been created by changing track numbers or erasing tracks. 1. Select and confirm “Track Pack” in step 5 of “Editing during the stop mode” on page 39. The following message appears on the display.
TRACK EDITING 6. Rotate MULTI JOG knob (+/– on the remote control) Add Fade In You can add fade-in at the beginning of a track. The beginning of the track is played with gradually rising level when fade-in has been added. ■ Editing during the stop mode 1. Select and confirm “Add Fade In” in step 5 of “Editing 7. Press COMPLETE. Disc that contains the track to add fade-in The fade-in is added to the beginning of the selected track for the selected length.
TRACK EDITING 3. Press COMPLETE. 4. Select the track to add fade-out by rotating the MULTI The fade-in is added to the beginning of the track being played for the selected length. Playback resumes from the beginning of the track the fade-in has been added to. Add Fade Out 5. Press the MULTI JOG knob (ENTER on the remote control) to confirm the track to add fade-out. The ending of the track for 8 seconds is repeatedly played with a 3-second (initial setting) fade-out.
TRACK EDITING ■ Editing during playback 1. Select and confirm “Add Fade Out” in step 2 of “Editing during playback” on page 39. The ending of the track for 8 seconds is repeatedly played with a 3-second (initial setting) fade-out. The following message appears on the display. Fade-out length –30 –10 R –6 –2 0 ■ Editing during the stop mode 1. Select and confirm “Track Title” in step 5 of “Editing Disc that contains the track to assign a title to L dB You can assign a title to a track.
TRACK EDITING 6. Enter the title characters by using the MULTI JOG knob or the alphabetical/numeric buttons on the remote control. See description on right for entering procedure. 7. Press COMPLETE when all the characters have been entered. The title is assigned to the selected track. This unit returns to the editing menu item selection. 1. Select and confirm “Track Title” in step 2 of “Editing during playback” on page 39. The track being played is confirmed for assigning the title to.
DISC EDITING You can do various editing operations on the discs that have been recorded on the HDD. Disc Editing Operation 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE MULTI JOG COPY MENU TIMER REC A.M.Q.R. FINALIZE REC ERASE MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT TRACK NO.
DISC EDITING ■ Editing during playback Disc Rename 1. Select and confirm “Disc Rename” in step 2 of You can move a disc and assign a new number. ■ Editing during the stop mode 1. Select and confirm “Disc Rename” in step 5 of “Editing during the stop mode” on page 52. The following message appears on the display. L 001? L dB –30 –10 –6 –2 0 Dsc001≥002 dB G –30 –10 –6 –2 0 GROUP R Disc being played Disc to be moved The disc number to be moved flashes. New disc number 2.
DISC EDITING Disc Erase Disc Combine You can erase a selected disc. You can combine a series of discs into one. ■ Editing during the stop mode ■ Editing during the stop mode 1. Select and confirm “Disc Erase” in step 5 of “Editing 1. Select and confirm “Disc Combine” in step 5 of during the stop mode” on page 52. The following message appears on the display. Erase “Editing during the stop mode” on page 52. The following message appears on the display.
DISC EDITING ■ Editing during playback 1. Select and confirm “Disc Combine” in step 2 of “Editing during playback” on page 52. The disc being played is confirmed to be the first disc in the combination. The number of the disc being played and the number of the disc to be the last in the combination appear on the display. 001 -002 L dB –30 –10 –6 –2 0 GROUP R You can divide a disc into two at the selected point. ■ Editing during the stop mode 1.
DISC EDITING ■ Editing during playback 1. Select and confirm “Disc Divide” in step 2 of “Editing during playback” on page 52. The disc being played is confirmed to be divided. “Div.from” and the dividing point (the number of the track to be the first after dividing) appear on the display. Div. from TRACK dB –30 –10 –6 –2 You can re-organize the disc numbers by eliminating unused disc numbers that have been created by changing disc numbers or erasing discs. 1.
DISC EDITING 2. Enter the title characters by using the MULTI JOG Disc Title knob or the alphabetical/numeric buttons on the remote control. See description below for entering procedure. You can assign a title to a recorded disc. ■ Editing during the stop mode 3. Press COMPLETE when all the characters have been 1. Select and confirm “Disc Title” in step 5 of “Editing during the stop mode” on page 52. The following message appears on the display.
UNDO FUNCTION You can cancel an operation and the result of a previous editing step on this unit (Undo function). OPEN/CLOSE COPY MULTI JOG TIMER REC REC MENU A.M.Q.R. FINALIZE MULTI JOG ER PUSH ENTER TEXT/TIME TEXT/TIME MODE TRACK NO. COMPLETE INPUT ERASE TRACK NO. WRITE MENU CLEAR MODE MENU MENU BOOKMARK DIGITAL REC LEVEL COMPLETE COPY INPUT REC FINALIZE ERASE ANALOG REC LEVEL COMPLETE CLEAR OPTICAL A.M.Q.R.
BOOKMARK While playing a track, you can place a bookmark temporarily on the track. Bookmark is convenient for immediate playback of the desired track and for creating a new album since the tracks with bookmarks are stored as a playlist. 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ +10 0 SPACE SYMBOL BOOKMARK REPEAT RANDOM INTRO BOOKMARK TRACK NO./BOOKMARK CLEAR MULTI JOG ER PUSH ENTER GROUP SKIP TEXT/TIME MODE MENU TRACK NO.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC Copying a Whole Group (Disc, Album or Bookmark) You can copy all tracks in a whole group of discs, albums or a bookmark. 1,3 4 2 1,3 5 MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR 4 7 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE COPY TIMER REC A.M.Q.R. FINALIZE TEXT/TIME INPUT REC ERASE TRACK NO.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC 4. Press COPY twice. 6. Start copying. The following message appears on the display, and this unit enters in the copy standby mode. Copying has not been started yet at this stage. Press w/d (w on the remote control) to start copying.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC Copying Favorite Tracks on the HDD 1 2 6 1 1 4 7 COPY 6 9 MULTI JOG PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE TIMER REC A.M.Q.R. FINALIZE NATURAL SOUND HDD/CD RECORDER 4 TEXT/TIME INPUT REC 4 ERASE TRACK NO.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC High Quality Copying You can make your own CD with high quality sound with the Audio Master Quality Recording mode. Cautions • Audio Master Quality Recording mode can be used only for copying from the HDD on a new CD-R disc. • Recordable time is 63 minutes for a 74-minute CD-R disc, and 68 minutes for a 79-minute CD-R disc. • Audio Master Quality Recording mode cannot be used for recording from an external component directly to a CD-R disc.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC Advanced Operations ■ Setting the copying mode This unit provides various copying modes. Choose the one that suits your needs. Initial setting: All Synchro MODE OPEN/CLOSE MULTI JOG COPY TIMER REC REC MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU A.M.Q.R. FINALIZE TRACK NO. COMPLETE ERASE CLEAR TEXT/TIME BOOKMARK INPUT TRACK NO. WRITE DIGITAL REC LEVEL COPY MODE INPUT REC FINALIZE ERASE A.M.Q.R.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC ■ Copying menu setting ■ Copy Method You can make detailed settings on the menu for your copying. Follow the steps described below for menu setting. Setting of the copying method. Copying may fail if the setting for “Copy Method” is not correctly made. MULTI JOG MENU Copy Method REC MULTI JOG ER PUSH ENTER L TEXT/TIME MODE MENU TRACK NO.
COPYING FROM THE HDD ONTO A CD-R OR CD-RW DISC ■ Copy Level ■ Copy Speed Setting of the sound level for copying. Sound level adjustment is not normally necessary. However it is possible to adjust the copying sound level to suit you needs. Setting of the copying speed.
RECORDING FROM AN EXTERNAL COMPONENT ONTO A CD-R OR CD-RW DISC You can record from an external component directly to a CD-R or CD-RW disc. Following is an explanation for digital recording from an external CD player connected to the DIGITAL IN (OPTICAL) or DIGITAL IN (COAXIAL) jacks on this unit. Note • Before starting to record, check the remaining time available for recording on the CD-R or CD-RW disc (see page 11). 1 1 1 4 4 MULTI JOG PUSH ENTER TEXT/TIME MODE MENU TRACK NO.
RECORDING FROM AN EXTERNAL COMPONENT ONTO A CD-R OR CD-RW DISC 6. Start recording. 9. When all recordings are completed, press FINALIZE Press w/d (w or d on the remote control) to start recording. 1 001 REC L dB –30 –10 –6 –2 0 R CDR Note • In the multi-synchronized, all-synchronized, or full autosynchronized recording mode, this unit automatically starts recording when the source component starts playback. 7. Start playback on an external CD player.
RECORDING FROM AN EXTERNAL COMPONENT ONTO A CD-R OR CD-RW DISC Advanced Operations ■ Setting the recording mode This unit provides various recording modes. Choose the one that suits your needs. Initial setting: Track Synchro MODE MULTI JOG 3. Press the MULTI JOG knob (ENTER on the remote MULTI JOG ER PUSH ENTER TEXT/TIME MODE TRACK NO.
FINALIZATION Finalization is the process that concludes recording, and allows a CD-R disc to be played on a standard CD player or a CD-RW disc to be played on a CD-RW-compatible player. 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE COPY MULTI JOG ER TEXT/TIME MODE TRACK NO. COMPLETE TIMER REC A.M.Q.R. FINALIZE PUSH ENTER MENU 2 CLEAR TEXT/TIME INPUT REC ERASE TRACK NO.
ERASING A CD-RW DISC You can erase the data recorded on a CD-RW disc. New recordings can be made in the space created by erasing. The following 4 types of erasing are possible with this unit. ■ Last Track Erase ■ TOC Erase This operation erases the last track on a disc. “Last Track Erase” cannot be performed if a CD-RW disc has been finalized, or only one track has been recorded on the disc. This operation is only available on a CD-RW disc that has been finalized.
DUPLICATION OF A CD You can quickly duplicate a commercially available CD using this unit. Caution • Duplication may not correctly made on a CD-R or CD-RW disc that does not support high speed writing. In this case, copy a CD onto the HDD first, then perform “Digital Move” on a CD-R or CD-RW disc at 2x or 1x speed. 1,3,6 4 1,3,6 2,6 4 5 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ OPEN/CLOSE COPY TIMER REC A.M.Q.R.
DUPLICATION OF A CD 5. Start copying from the CD onto the HDD. Press w/d (w on the remote control) to start copying. The copying conditions are as follows: • Copy Method: “Digital Copy” • Copy Level: 0dB • Copy Speed: “Best Effort” Cautions • If copying is canceled by a being pressed, even the data that has been copied before cancellation does not remain on the HDD. • If a track is copy protected by the SCMS standard, that track cannot be copied onto the HDD.
DUPLICATION OF A CD High Quality Duplication You can duplicate a CD with high quality sound with the Audio Master Quality Recording mode. Cautions • Audio Master Quality Recording mode can be used only for duplicating on a new CD-R disc. • Recordable time is 63 minutes for a 74-minute CD-R disc, and 68 minutes for an 79-minute CD-R disc. 1,5 2 1,5 1,5 4 2 3 MULTI JOG NATURAL SOUND HDD/CD RECORDER PUSH ENTER TEXT/TIME MODE MENU TRACK NO.
DUPLICATION OF A CD Cautions • When total time of the CD to be duplicated exceeds recordable time on a CD-R disc (63 minutes for a 74-minute CD-R disc and 68 minutes for an 79-minute CD-R disc), the following message appears on the display. In this case, Audio Master Quality Recording mode cannot be used. No Enough Spc DUPLCT A.M.Q.R.
PLAYBACK This unit can play back tracks recorded on the 2 types of recording media; HDD and CD. Press HDD to play tracks recorded on the HDD, and press CDR to play tracks recorded on a CD (including a CD-R and a CD-RW disc). Playing a CD Playing Tracks on the HDD 1 MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR MULTI JOG ER PUSH ENTER BOOKMARK TEXT/TIME MODE MENU TRACK NO.
PLAYBACK 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO MULTI JOG MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR GROUP SKIP q GROUP SKIP w GROUP SKIP BOOKMARK DIGITAL REC LEVEL COPY e INPUT REC A.M.Q.R. FINALIZE ERASE r ANALOG REC LEVEL HDD OPTICAL CDR COAXIAL ANALOG MIN MAX t/e r/y Finding the Desired Passage (Search) Press and hold r/y (r on the remote control) during playback.
PLAYBACK 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE COPY TIMER REC REC MULTI JOG A.M.Q.R. FINALIZE ERASE MULTI JOG ER PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR TEXT/TIME INPUT MODE TRACK NO. WRITE MENU BOOKMARK GROUP SKIP t y DIGITAL REC LEVEL COMPLETE COPY INPUT REC FINALIZE ERASE A.M.Q.R.
PLAYBACK Selecting Tracks Using On-ScreenDisplay (OSD) ■ Select a track 1. Press the MULTI JOG knob to turn on the TRACK indicator. TRACK You can display a list of groups and tracks to be played by connecting this unit to a monitor. If you display the list on a screen, it is much easier to see than on the display. L dB –30 –10 –6 –2 0 R The following list will be displayed on a monitor. Note • When “VIDEO Output” on the system utility is set to OFF, no OSD signals will be output.
VARIOUS PLAYBACK This unit provides various playback methods according to the setting. The following steps describe the setting procedure for each setting. Notes • The setting of play style, random play, repeat play, and intro play can be set during the playback. • The setting of play style, random play, and full repeat play is memorized even after the power of this unit has been turned off. Finding the Desired Passage by Time (Time Search) You can search the desired part by setting the time. 1.
VARIOUS PLAYBACK • When random play is set, all tracks that belong to the selected group category are played in a random sequence. • When full repeat play is set, all tracks that belong to the selected group category are repeatedly played. • When intro play is set, the beginnings of all tracks that belong to the selected group category are played one after another. For example, if full repeat play is set during the playback of disc 1, all tracks recorded to discs 1 and 2 are repeatedly played.
VARIOUS PLAYBACK Full Repeat Play Random Play You can repeatedly listen to all tracks recorded in a group (or a CD) or group category. You can listen to all tracks recorded in a group on the HDD or on a CD in a random sequence. ■ To set full repeat play ■ To set random play 1. Press HDD or CDR to select the drive to be used. 2. Press MODE to start the playback mode setting. 3. Rotate the MULTI JOG knob (press +/– on the remote 1. Press HDD or CDR to select the drive to be used. 2.
VARIOUS PLAYBACK Intro Play Bookmark Play You can listen to the beginnings of the tracks for a set amount of time one after another. You can easily listen to a group of desired tracks by selecting a list of tracks with bookmarks. ■ To set intro play ■ To place a bookmark 1. Press HDD or CDR to select the drive to be used. 2. Press MODE to start the playback mode setting. 3. Rotate the MULTI JOG knob (press +/– on the remote Press TRACK NO.
DAC (DIGITAL/ANALOG CONVERTER) MODE This unit has a DAC mode function. You can switch the input signals, as an input selector, to output from both the analog and digital jacks to the amplifier connected to this unit. 4 JKL 5 MNO 6 PQR 7 STU 8 VWX 9 YZ 0 SPACE +10 SYMBOL BOOKMARK REPEAT RANDOM INTRO OPEN/CLOSE 5 2,3,4 1,5 COPY MULTI JOG ER TIMER REC A.M.Q.R. FINALIZE REC ERASE PUSH ENTER TEXT/TIME MODE MENU TRACK NO.
HDD UTILITY ■ To check the HDD utility (HDD Info.) ■ To format the HDD (HDD Format) You can check the HDD utility (capacity, usage, and available space) of this unit. You can format the HDD in this unit. 1. Press MENU while this unit is in the stop mode. The display changes for the menu item selection. 2. Select “HDD Utility” by rotating the MULTI JOG knob (pressing +/– on the remote control). 1. Press MENU while this unit is in the stop mode.
SYSTEM UTILITY ■ To check the firmware version (Firm. Version) ■ To initialize the setting for each item (Initialize) Software that is called “firmware” is built into this unit. This firmware controls the operation. The following steps describe the firmware version check procedures. You can initialize the settings that have been changed. The OPC data stored in this unit is also initialized. 1. Press MENU while this unit is in the stop mode. The display changes for the menu item selection. 2.
SYSTEM UTILITY ■ To change the display brightness (Dimmer Setup) ■ To set the video output (VIDEO Output) You can change the brightness of the display. You can switch the on-screen display output through the VIDEO OUT jacks on and off. 1. Press MENU while this unit is in the stop mode. 1. Press MENU while this unit is in the stop mode. The display changes for the menu item selection. 2. Select “Sys. Utility” by rotating the MULTI JOG knob The display changes for the menu item selection. 2.
SYSTEM UTILITY ■ To set auto play (Auto Play) You can set the auto play function which automatically starts playback when the power of this unit is turned on. 1. Press MENU while this unit is in the stop mode. ■ To update the firmware version (Firm. Update) This menu is prepared for the expansion of the functions in the future. The display changes for the menu item selection. 2. Select “Sys. Utility” by rotating the MULTI JOG knob (pressing +/– on the remote control). 3.
ON-SCREEN DISPLAY (OSD) You can display the list of groups or tracks to be played, copying/recording settings and the list of the setting items on the monitor by connecting the monitor to this unit. ■ List of groups or tracks ■ List of setting items The numbers and titles of groups, or the numbers and titles of tracks are displayed. Press the MULTI JOG knob to switch the list displayed. The names of items to be set are displayed. Grp Dsc 1: Dsc 2: Dsc 3: Alb 1: Alb 2: Mark : Tr.
DISPLAY MESSAGES Can’t Copy This message is displayed for approximately 3 seconds when digital recording or copying is not possible according to the SCMS standard. See “Rules of Digital Recording” on page 5. Can’t Edit This message is displayed when a prohibited editing operation has been attempted. Can’t Tr.Lev. The album with its tracks’ level adjusted is to be copied to a CD-R disc in the Audio Master Quality Recording mode. Can’t use HDD The loaded HDD has been formatted by other CDR-HD1300s.
DISPLAY MESSAGES Reading This unit reads the format of the CD, CD-R, or CD-RW disc loaded on the disc tray. Approximately 15 seconds may be required to complete this automatic adjustment. However, this time length may change according to the type of the CD, CD-R, or CD-RW disc that has been loaded. Slow Fnlz OK? This message confirms starting the slow finalization of a CD-R or CD-RW disc. If you wish to finalize, press w/d (w on the remote control).
TROUBLESHOOTING If this unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If they cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for assistance. SYMPTOM This unit does not turn on when POWER is pressed. Playback does not begin with the CD loaded. Playback is delayed, or begins at the wrong place.
TROUBLESHOOTING SYMPTOM CAUSE REMEDY This unit does not operate properly. There is rotation noise of the fan. A noise occurs at the change of the tracks that has been recorded from the analog record and edited. Remote control does not work. The internal microcomputer has been frozen. Turn off the power of this unit and then turn on again after about one minute. The fan starts to rotate to cool off the temperature inside this unit.
SPECIFICATIONS ■ Audio Performance ■ Outputs Frequency response .................................... 5 to 20,000 Hz, ±0.5 dB ANALOG LINE OUT (PLAY) Type ............................................................................... Pin jack Standard output level (1 kHz, 0 dB) ..................... 2.0±0.5 Vrms S/N ratio (EIAJ) Playback ......................................................................... 105 dB Recording .........................................................................
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER APPART PRODUIT LASER DE CLASSE 1 ATTENTION L’emploi de commandes, de réglages ou un choix de procédures différents des spécifications de cette brochure peut entraîner une exposition à d’éventuelles radiations pouvant être dangereses.
UAB CDR-HD1300/CDR-HD1300E CDR-HD1300 CDR-HD1300E HDD/CD Recorder Enregistreur CD/Disque Dur MULTI JOG PUSH ENTER TEXT/TIME MODE MENU TRACK NO. COMPLETE CLEAR BOOKMARK DIGITAL REC LEVEL INPUT REC FINALIZE ERASE ANALOG REC LEVEL OPTICAL COAXIAL ANALOG MIN YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H.
CDR-HD1300 CDR-HD1300E HDD Installation Manual Manuel d’installation du disque dur Festplattenspeicher-Installationshandbuch Hårddiskinstallationsanvisningar Manuale d’installazione dell’HDD Manual de instalación del disco duro Installatiehandleiding voor de harde schijf 999_HD1300(HDD)_GB 1 02.6.
INSTALLING THE HDD There are some models that do not have a built-in hard disk drive (HDD) depending on the sales location. Please purchase a commercially available HDD for internal use and install it on this unit correctly, referring to the instruction below. ■ Required specifications of the HDD Interface .................................................................... IDE/ATA type 1. Loosen the two fixing screws on the HDD slot door and open the HDD slot door. Data Transfer Mode ...................
■ Installation procedures (continued) ■ Formatting the HDD 5. Push the HDD tray and connect the IDE cable and the If you install a new HDD, you need to format the HDD before using with this unit. power cable. • Make sure that the terminals and connectors are in the correct direction, and connect the cables securely. • Static electricity can damage the HDD. Be careful not to touch the terminal pins and the circuit board. • Do not apply excessive force on the HDD tray. 1.
Printed in Malaysia 999_HD1300(HDD)_GB 16 02.6.