English Español Pre-Amplifier Owner´s Manual Manual de instrucciones
English Thank you and congratulations on your purchase of this Yamaha product. ¡¡ You can enjoy the high-quality stereo sound of this preamplifier at home. ¡¡ This Owner’s Manual describes the unit’s features, connection procedures, and operations. ¡¡ To use the product properly and safely, we suggest that you read this manual and Safety Brochure (separate booklet) thoroughly. Keep the manual in a safe, accessible place for future reference.
Table of contents Features . . . . . . . . . . . . . . . . . . . . . . . . 2 Operations Supplied accessories . . . . . . . . . . . . . . . . 4 Turning the power on . . . . . . . . . . . . . . 28 Maintenance . . . . . . . . . . . . . . . . . . . . . 4 Selecting the input and output . . . . . . . . 28 Mirror-finish side panels . . . . . . . . . . . . 4 Selecting the input from the EXT.IN jacks . .
Supplied accessories Please make sure that the following accessories are included in the package. • • • • • Remote control Batteries (AAA, R03, UM-4) (x2) Power cord Owner’s Manual (this book) Safety Brochure (separate booklet) WARNING Do not use the supplied power cord for other devices. Maintenance To use this product for an extended period of time, we recommend that you maintain it regularly. WARNING • Check the power cord regularly to see if it is dusty. If so, wipe off the dust completely.
English Part Names and Functions This section lists the names and describes the function of various parts on the front and rear panels, and the remote control.
Front panel A. STANDBY/ON/OFF (Power) switch/ indicator Turns the power to the unit on (standby) or off. STANDBY/ON: Switches between standby and on using the A AMP key on the remote control. OFF: Turns the power to the unit off.
English D. TRIM selector Switches the headphone amp gain. The unit will adjust the volume level when headphones are plugged in to avoid sudden changes in volume by modifying the level balance between the audio output from the PHONES jack and from the speakers. Choices: −6 dB, 0 dB, +6 dB, +12 dB E. GAIN selector Switches the preamp gain. The unit will smoothly adapt to the power amp gain and speaker sensitivity, enabling you to make fine volume adjustments.
Front panel H. BASS control K. EXT. DIRECT switch/indicator Adjusts the low-frequency response in the range from −10 dB to +10 dB (in 0.5 dB steps). The center position produces a flat response. If you press the EXT. DIRECT switch once, the EXT. DIRECT indicator will light up, and the audio source input at the EXT. IN jacks will be output at the connected output jacks. For more information, refer to “Connecting another preamplifier” (page 23) and “Selecting the input and output” (page 28).
English L. INPUT selector/indicator N. AUDIO MUTE switch/indicator Enables you to select the input source to play back. Options are: PHONO, PHONO BAL, TUNER, CD, BAL 1, BAL 2, LINE 1, and LINE 2. The indicator for the selected input source lights up. Press this switch to reduce the current volume level by approximately 20 dB. The indicator will light up. Press again to restore the audio output to the previous volume level. The indicator will turn off.
Rear panel Note For information regarding the connection procedure, refer to “Connections” (page 19). A. PHONO jacks RCA and XLR-type jacks. If the INPUT selector is set to PHONO, the signals at the RCA-type PHONO jacks will be the input source. If the INPUT selector is set to PHONO BAL, the signals at the XLR-type PHONO jacks will be the input source. Your preamplifier comes with a shorting plug installed on each RCA-type PHONO input jack.
English C. BAL 1/BAL 2 jacks E. PHASE selector These are two sets of XLR-type balanced input jacks. If the INPUT selector is set to BAL 1 or BAL 2, signals at the corresponding XLR jacks will be the input source. Specifies the HOT pin position for the XLR-type balanced input jacks (BAL 1 and BAL 2 jacks). NORMAL: Pin #2 is specified as HOT. INV.: Pin #3 is specified as HOT. For more information, refer to “Balanced and unbalanced connections” (page 14).
Rear panel G. CD jacks Note These are RCA input jacks. If the INPUT selector is set to CD, signals at these jacks will be the input source. Connect your CD player here. • Connect the LINE 2 IN jacks and LINE 2 OUT (recording) jacks to the same component. • The LINE 2 OUT (recording) jacks will not output any signals if the INPUT selector is set to LINE 2 or the EXT. DIRECT switch is pressed. H. LINE 1 jacks These are RCA input jacks.
English Note O. REMOTE IN/REMOTE OUT jacks The volume level is fixed. Operating the VOLUME control or GAIN selector on this unit will not change the volume level of the signal from the EXT. IN jacks. Adjust the volume level using the volume control on the component connected to the EXT. IN jacks. These are monaural mini jacks. Connect external components that support the remote function here. For more information, refer to “Remote connections” (page 25). L.
Balanced and unbalanced connections XLR jack (male) Lever This unit features XLR-type balanced jacks and RCAtype unbalanced input jacks. 2 Note Do not use balanced and unbalanced connections between two components simultaneously. Doing so would create a ground loop that could generate static and noise. Balanced connection XLR connector (female) 2 1 1 3 3 A balanced connection is designed to cancel and prevent unwanted noise.
If you are connecting an audio component that features only standard RCA jacks, use the RCA jacks on this unit for unbalanced connections. For unbalanced connections, unbalanced cables with RCA connectors should be used. These jacks and connectors do not feature a male or female design nor polarity differences. If the PHASE selector is set to NORMAL, pin #2 becomes Hot.
Remote control A. Infrared signal transmitter Outputs infrared control signals toward the unit. B. A AMP key AMP OPEN/CLOSE CD 1 2 Turns on the power to the unit or switches it to standby mode. For more information regarding standby mode, refer to “Front panel” (page 6). BAL BAL C. Input select keys UNBAL PHONO 1 2 LINE CD EXT.DIRECT TUNER BAND PRESET SOURCE LAYER VOLUME Enable you to select the input source to be played back.
E. A CD key H. VOLUME +/− keys Turns on the power to a connected Yamaha CD player, or switches it to standby mode. Adjust the volume level. OPEN/CLOSE key Opens or closes the disc tray of a connected Yamaha CD player. For more information, refer to the owner’s manual for your CD player. The VOLUME +/− keys on the remote control will not affect the volume level if EXT. DIRECT is selected as the input source.
Installing batteries in the remote control 1 2 Remove the battery compartment cover. Insert two batteries (AAA, R03, UM-4) according to the polarity markings (+ and −) on the inside of the battery compartment. 1 2 3 CAUTION • Do not use a new and old batteries at the same time. Otherwise, fire, burns, or irritation due to leaking battery liquid might be caused. • Do not use two different types of batteries at the same time.
English Connections This section explains how to connect the unit to an audio source, such as a tuner or CD player, and a power amplifier. CAUTION Turn off the power to all components before making any connections. NOTICE • Do not use balanced and unbalanced connections between two components simultaneously. Doing so would create a ground loop that could generate static and noise. • If you are planning to connect external components, read and follow the instruction manuals for those components.
Connecting an external component Turntable Turntable Network audio player 20 CD player CD player Tuner BD player Hard disk recorder, etc.
Power amplifier AV amplifier, etc. Power amplifier Active subwoofer English Other preamplifier NOTICE Do not use balanced and unbalanced connections between two components simultaneously. Doing so would create a ground loop that could generate static and noise.
Connecting a turntable Connect your turntable to the PHONO jacks on this unit. The unit provides XLR-type balanced jacks and RCAtype unbalanced input jacks. Balanced connection Turntable Connecting a recording component You can connect a recording device, such as a hard disk recorder to the unit, and record audio input from the unit. Connect the recording component to both LINE 2 IN jacks and LINE 2 OUT (recording) jacks.
Connecting a power amplifier and an active subwoofer If you connect the output of another preamplifier to the EXT. IN jacks on this unit and press the EXT. DIRECT switch, the source signal will pass through the unit and will be output to the connected power amplifier. The source signal input at the balanced EXT. IN jacks will be output at the balanced BAL jacks. The source signal input at the unbalanced EXT. IN jacks will be output at the LINE 1 and LINE 2 jacks.
Trigger connections Controlling the power on-andoff operation of a connected component, such as a power amplifier, in sync with this unit Controlling the unit’s power onand-off operation in sync with a connected component, such as an AV receiver You can control the power on-and-off operation of a connected component, such as a Yamaha CD player or power amplifier, in sync with this unit. Use a system cable to connect the unit’s TRIGGER OUT jack to the connected component’s TRIGGER IN jack.
Operating the unit from another room Remote connection between Yamaha components If you connect an infrared receiver and transmitter to the unit’s REMOTE IN/OUT jacks, you will be able to operate the unit and/or external component from another room, using the supplied remote control. If you have another Yamaha component that supports remote connections, as this unit does, an infrared transmitter is not necessary.
Connecting the power cord After all connections are complete, make sure that the STANDBY/ON/OFF (Power) switch is turned off, then plug the power cord into the AC IN connector of the unit, and then plug the power cord into the AC outlet. Supplied power cord C-5000 Rear panel CAUTION • Do not use an AC outlet that is so loose that the plug does not stay firmly in place. Otherwise, fire, electric shock, or burning might be caused.
English Operations This section explains basic operating procedures. You can follow these procedures to take advantage of the unit’s functions. These procedures are intended only as examples.
Turning the power on CAUTION Be sure to lower the volume level to minimum before turning the power on. Selecting the input and output Select a pair of output jacks using the OUTPUT selector. Turn the power on by setting the STANDBY/ON/OFF (Power) switch on the front panel to STANDBY/ON. All jacks Off Only BAL jacks Only LINE 1 jacks Only LINE 2 jacks Select the audio source using the INPUT selector. If the unit is in standby mode, you can also turn the power on using the remote control.
Adjusting the turntable input setting Selecting the input from the EXT.IN jacks English PHONO selector Set the PHONO selector according to the turntable cartridge. Options for turntable cartridge Press the EXT. DIRECT switch. The EXT. DIRECT indicator will light up. The INPUT selector setting will be disabled, and the audio source input from the EXT. IN jacks will be output at a pair of the output jacks.
Adjusting the volume level Subsonic filter Turn on the SUBSONIC FILTER switch to apply the subsonic filter, as needed. A resonating turntable tone arm or a warped vinyl record could cause a very low frequency rumble (subsonic noise) that might apply load and damage to the speakers. A subsonic filter will cut such noise to protect the speakers. Set the gain using the GAIN selector so that you can make fine volume adjustments. Gain Adjust the volume level using the VOLUME control.
Adjusting the tone Lowering the volume level momentarily Adjust the volume level balance between the left and right speakers using the BALANCE control. English Press the AUDIO MUTE switch to reduce the current volume level by approximately 20 dB. Press the switch again to restore the previous volume level. Adjust the volume level of the high and low ranges using the BASS and TREBLE control.
Connecting headphones If headphones are connected to the PHONES jack, no signal will be output at the output jacks (BAL, LINE 1, and LINE 2 output jacks) on the rear panel. Use the TRIM selector to switch the headphone amp gain so you can adjust the level balance between the audio output from the PHONES jack and the speakers to avoid sudden changes in volume. Note If EXT. DIRECT is selected, no signal will be output from the PHONES jack.
English Reference Materials 33
General specifications Rated output voltage/output impedance (Input 200 mV, 20 Hz to 20 kHz, THD 0.01%) BAL (BYPASS). . . . . . . . . . . . . . . . . . . 2 Vrms/150Ω BAL (ATT. −6dB). . . . . . . . . . . . . . . . . 1 Vrms/150Ω LINE 1/LINE 2. . . . . . . . . . . . . . . . . . . 1 Vrms/150Ω LINE 2 OUT (recording). . . . . . . 200 mVrms/1.2 kΩ Total harmonic distortion plus noise (JEITA, input 0.5 V, 20 Hz to 20 kHz) BAL 1/BAL 2/TUNER/CD/LINE 1/LINE 2 IN → BAL/LINE 1/LINE 2 . . . . . . . . . . . . . . . . .
Headphone jack rated output power (1 kHz, 32Ω, 0.2% THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mW + 35 mW English RIAA equalization deviation MC/MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.5 dB Subsonic filter characteristics MC/MM . . . . . . . . . . . . . . . . . . . . . . . . . 15 Hz/−3 dB Power supply [Models for U.S.A. and Canada]. . . AC 120 V, 60 Hz [Model for China]. . . . . . . . . . . . . . AC 220 V, 50 Hz [Model for Korea]. . . . . . . . . . . . . .
EXT. IN LINE 2 OUT (recording) TUNER /CD LINE 1/ LINE 2 PHONO PHONO BAL 2 BAL 1 INPUT SUB TRANSFORMER POWER RELAY Relay BAL→UNBAL ±32V ±81V INDEPENDENT CONSTANT BASS MIDDLE TREBLE VOLUME TONE CONTROL +99V +12V CURRENT POWER SUPPLY TOROIDAL TRANSFORMER SUBSONIC ON / THROUGH TONE CONTROL ON / THROUGH INDEPENDENT REGULATED POWER SUPPLY (for AUDIO) MOTOR VOL/ RELAY BAL Normal / UNBAL: 18.6dB BAL ATT: 12.
Audio characteristics Frequency response (tone control) 14 Response (dB) 10 +10dB 8 +8dB 6 +6dB 4 +4dB 2 +2dB 0 ±0dB English 12 –2dB –2 –4dB –4 –6dB –6 –8dB –8 –10dB –10 –12 –14 10 20 30 50 100 200 300 500 1k 2k 3k 5k 10k 20k 30k 50k 100k Frequency (Hz) Total harmonic distortion (PHONO) 10 5 2 1 0.5 THD + N Ratio (%) 0.2 0.1 20 Hz 0.05 1 kHz 20 kHz 0.02 0.01 0.005 0.002 0.001 0.0005 0.0002 0.
Frequency response (subsonic filter) 10 5 THROUGH Response (dB) 0 –5 ON –10 –15 –20 –25 5 10 20 30 50 100 200 300 500 1k 2k 3k 5k 10k 20k 30k 50k 100k Frequency (Hz) Volume curve 10 0 GAIN selector: –6 dB –20 Volume Level (dB) GAIN selector: 0 dB –40 GAIN selector: –12 dB –60 –80 –100 –110 0.00 50.00 100.00 150.00 Volume control (degree) 38 200.00 250.00 300.
Troubleshooting Refer to the table below if this unit does not function properly. If the instructions below do not help, or if the problem you are experiencing is not listed below, turn off the unit, disconnect the power cord, and contact the nearest authorized Yamaha dealer or service center. Cause Remedy See page The power cord is not connected to the AC IN connector on the rear panel or is not plugged into an AC outlet. Connect the power cord firmly.
Remedy See page Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables might be defective. 20 The turntable is not grounded to the GND terminal. Connect the turntable to the GND terminal of this unit. 22 Both balanced and line cables are being used simultaneously between two components. Do not use both balanced and line cables simultaneously between two components. Doing so would create a ground loop that could generate static and noise.
Index O AC IN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusting the turntable input . . . . . . . . . . . . . . . . . ATTENUATOR selector . . . . . . . . . . . . . . . . . . . . . AUDIO MUTE switch . . . . . . . . . . . . . . . . . . . . . . AUTO POWER STANDBY switch . . . . . . . . . . . . 26 29 30 31 13 BAL 1 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BAL 2 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BALANCE control . . .
Español Gracias y enhorabuena por la compra de este producto Yamaha. ¡¡ Puede disfrutar del sonido estéreo de calidad alta de este preamplificador en casa. ¡¡ En este Manual del propietario se describen las funciones, los procedimientos de conexión y las operaciones de la unidad. ¡¡ Para utilizar el producto de forma adecuada y segura, le sugerimos que lea detenidamente este manual y el Folleto de seguridad (folleto independiente).
Contenido Acerca de este manual . . . . . . . . . . . . . . 42 Accesorios suministrados . . . . . . . . . . . . 44 Mantenimiento . . . . . . . . . . . . . . . . . . 44 Paneles laterales con acabado de espejo . . 44 Superficies distintas de los paneles laterales con acabado de espejo . . . . . . . 44 Nombres y funciones de las piezas Panel delantero . . . . . . . . . . . . . . . . . . 46 Panel trasero . . . . . . . . . . . . . .
Accesorios suministrados Asegúrese de que el embalaje incluye los accesorios siguientes. • • • • • Mando a distancia Pilas (AAA, R03, UM-4) (x2) Cable de alimentación Manual de instrucciones (este libro) Folleto de seguridad (folleto independiente) ADVERTENCIA No utilice el cable de alimentación suministrado para otros dispositivos. Mantenimiento Para utilizar este producto durante un periodo prolongado, se recomienda realizar un mantenimiento periódico.
Español Nombres y funciones de las piezas En esta sección se enumeran los nombres y se describen las funciones de las distintas piezas de los paneles delantero y trasero, así como del mando a distancia.
Panel delantero A. Interruptor/indicador STANDBY/ON/ OFF (alimentación) Activa (espera) o desactiva la alimentación de la unidad. STANDBY/ON: cambia entre el modo de espera y el activado usando la tecla A AMP del mando a distancia. OFF: desactiva la alimentación de la unidad.
Español D. Selector TRIM Cambia la ganancia del amplificador de auriculares. La unidad ajustará el nivel de volumen cuando los auriculares estén conectados para evitar cambios repentinos de volumen modificando el balance de nivel entre la salida de audio procedente del jack PHONES y de los altavoces. Opciones: −6 dB, 0 dB, +6 dB, +12 dB E. Selector GAIN Cambia la ganancia del preamplificador.
Panel delantero H. Control BASS K. Interruptor/indicador EXT. DIRECT Ajusta la respuesta de frecuencia baja en la gama de −10 dB a +10 dB (en pasos de 0,5 dB). La posición central produce una respuesta plana. Si pulsa el interruptor EXT. DIRECT una vez, el indicador EXT. DIRECT se iluminará, y la entrada de fuente de audio en los jacks EXT. IN se emitirá por los jacks de salida conectados.
Español L. Selector/indicador INPUT N. Interruptor/indicador AUDIO MUTE Permite seleccionar la fuente de entrada que se va a reproducir. Las opciones son: PHONO, PHONO BAL, TUNER, CD, BAL 1, BAL 2, LINE 1 y LINE 2. El indicador para la fuente de entrada seleccionada se ilumina. Pulse este interruptor para reducir el nivel de volumen actual 20 dB aproximadamente. El indicador se iluminará. Púlselo de nuevo para reponer la salida de audio al nivel de volumen anterior.
Panel trasero Nota Para obtener información acerca del procedimiento de conexión, consulte “Conexiones” (página 59). A. Jacks PHONO Jacks de tipo RCA y XLR. Si el selector INPUT se ha establecido en PHONO, las señales en los jacks PHONO de tipo RCA serán la fuente de entrada. Si el selector INPUT se ha establecido en PHONO BAL, las señales en los jacks PHONO de tipo XLR serán la fuente de entrada.
Español C. Jacks BAL 1/BAL 2 E. Selector PHASE Se trata de dos juegos de jacks de entrada balanceada de tipo XLR. Si el selector INPUT se ha establecido en BAL 1 o BAL 2, las señales en los jacks XLR correspondientes serán la fuente de entrada. Especifica la posición del contacto con corriente para los jacks de entrada balanceada de tipo XLR (jacks BAL 1 y BAL 2). NORMAL: se especifica que el contacto n.º 2 tiene corriente. INV.: se especifica que el contacto n.º 3 tiene corriente.
Panel trasero G. Jacks CD Nota Se trata de jacks de entrada RCA. Si el selector INPUT se ha establecido en CD, las señales en estos jacks serán la fuente de entrada. Conecte el reproductor de CD aquí. • Conecte los jacks LINE 2 IN y los jacks LINE 2 OUT (grabación) al mismo componente. • Los jacks LINE 2 OUT (grabación) no emitirán señales si el selector INPUT se ha establecido en LINE 2 o el interruptor EXT. DIRECT está pulsado. H. Jacks LINE 1 Se trata de jacks de entrada RCA.
Español Nota O. Jacks REMOTE IN/REMOTE OUT El nivel de volumen es fijo. Al manipular el control VOLUME o el selector GAIN en esta unidad no cambiará el nivel de volumen de la señal procedente de los jacks EXT. IN. Ajuste el nivel de volumen con el control de volumen del componente conectado a los jacks EXT. IN. Se trata de mini jacks monaurales. Conecte componentes externos compatibles con la función remota aquí.
Conexiones balanceadas y no balanceadas Jack XLR (macho) Palanca Esta unidad presenta jacks balanceados de tipo XLR y jacks de entrada no balanceada de tipo RCA. 2 Nota No utilice conexiones balanceadas y no balanceadas entre dos componentes simultáneamente. Si lo hace se creará un bucle a tierra que podría generar estática y ruido. Conexión balanceada Una conexión balanceada está diseñada para cancelar y evitar el ruido no deseado.
Conexión no balanceada Si va a conectar un componente de audio que solo incluye jacks RCA estándar, utilice los jacks RCA de esta unidad para conexiones no balanceadas. Para conexiones no balanceadas, se deben utilizar cables no balanceados con conectores RCA. Estos jacks y conectores no presentan un diseño de tipo macho o hembra ni diferencias de polaridad. Español Si el selector PHASE se establece en NORMAL, el contacto n.º 2 recibe corriente.
Mando a distancia A. Transmisor de señales infrarrojas Emite señales infrarrojas de control hacia la unidad. B. Tecla A AMP AMP OPEN/CLOSE CD 1 2 Enciende la alimentación de la unidad o cambia al modo de espera. Para obtener más información sobre el modo de espera, consulte “Panel delantero” (página 46). BAL BAL C. Teclas de selección de entrada UNBAL PHONO 1 2 LINE CD EXT.
E. Tecla A CD H. Teclas VOLUME +/− Enciende la alimentación de un reproductor de CD Yamaha conectado o lo cambia al modo de espera. Ajuste el nivel del volumen. OPEN/CLOSE Abre o cierra la bandeja del disco de un reproductor de CD Yamaha conectado. Para obtener más información, consulte el manual del propietario de su reproductor de CD. Las teclas VOLUME +/− en el mando a distancia no afectarán al nivel de volumen si EXT. DIRECT está seleccionado como la fuente de entrada.
Instalación de las pilas en el mando a distancia 1 2 Retire la tapa del compartimento de las pilas. Introduzca las dos pilas (AAA, R03, UM-4) teniendo en cuenta las marcas de polaridad (+ y −) del interior del compartimento de las pilas. 1 2 3 Vuelva a colocar la tapa del compartimento de las pilas. ATENCIÓN • No utilice nuevas y antiguas al mismo tiempo. De lo contrario, podrían producirse incendios, quemaduras o irritaciones debido a la fuga de líquido de las pilas.
Español Conexiones En esta sección se describe cómo conectar la unidad a una fuente de audio, como un sintonizador o un reproductor de CD, y a un amplificador de potencia. ATENCIÓN Desactive la alimentación de todos los componentes antes de realizar conexiones. AVISO • No utilice conexiones balanceadas y no balanceadas entre dos componentes simultáneamente. Si lo hace se creará un bucle a tierra que podría generar estática y ruido.
Conexión de un componente externo Giradiscos Giradiscos Reproductor de CD Reproductor de audio de red 60 Reproductor de CD Sintonizador Reproductor de BD Grabador de disco duro, etc.
Amplificador de potencia Altavoz de subgraves activo Español Otro preamplificador Amplificador AV, etc. Amplificador de potencia AVISO No utilice conexiones balanceadas y no balanceadas entre dos componentes simultáneamente. Si lo hace se creará un bucle a tierra que podría generar estática y ruido.
Conexión de un giradiscos Conecte el giradiscos a los jack PHONO de esta unidad. La unidad proporciona jacks balanceados de tipo XLR y jacks de entrada no balanceada de tipo RCA. Conexión balanceada Giradiscos Conexión de un componente de grabación Puede conectar un dispositivo de grabación, como un grabador de disco duro, a la unidad y grabar la entrada de audio procedente de la unidad. Conecte el componente de grabación a los jacks LINE 2 IN y los jacks LINE 2 OUT (grabación).
Conexión de otro preamplificador Si conecta la salida de otro preamplificador a los jacks EXT. IN de esa unidad y pulsa el interruptor EXT. DIRECT, la señal de fuente atravesará la unidad y se emitirá por el amplificador de potencia conectado. La entrada de señal de fuente en los jacks EXT. IN balanceados se emitirá por los jacks BAL balanceados. La entrada de señal de fuente en los jacks EXT. IN no balanceados se emitirá por los jacks LINE 1 y LINE 2.
Conexiones de activación Control de la operación de encendido y apagado de un componente conectado, como un amplificador de potencia, de manera sincronizada con esta unidad Puede controlar la operación de encendido y apagado de un componente conectado, como un reproductor de CD Yamaha o un amplificador de potencia, de manera sincronizada con esta unidad. Utilice un cable del sistema para conectar el jack TRIGGER OUT de la unidad al jack TRIGGER IN del componente conectado.
Control de la unidad desde otra habitación Conexión remota entre componentes Yamaha Si conecta un receptor y un transmisor de señales infrarrojas a los jacks REMOTE IN/OUT de la unidad, podrá controlar la unidad o un componente externo desde otra habitación con el mando a distancia suministrado. Si dispone de otro componente Yamaha compatible con conexiones remotas, como es el caso de esta unidad, no es necesario un transmisor de infrarrojos.
Conexión del cable de alimentación Una vez realizadas todas las conexiones, asegúrese de que el interruptor STANDBY/ON/OFF (alimentación) está desactivado y, a continuación, enchufe el cable de alimentación al conector AC IN de la unidad y luego enchúfelo a la toma de CA.
Español Operaciones En esta sección se describen los procedimientos básicos de funcionamiento. Puede seguir estos procedimientos para aprovechar las funciones de la unidad. Estos procedimientos se proporcionan simplemente como ejemplos.
Encendido de la unidad Selección de la entrada y la salida Seleccione una pareja de jacks de salida con el selector OUTPUT. ATENCIÓN Asegúrese de bajar el nivel de volumen al mínimo antes de activar la alimentación. Active la alimentación estableciendo el interruptor STANDBY/ON/OFF (alimentación) en el panel delantero en STANDBY/ON. Todos los jacks Apagado Solo los jacks BAL Solo los jacks LINE 1 Solo los jacks LINE 2 Seleccione la fuente de audio con el selector INPUT.
Selección de la entrada desde los jacks EXT.IN Selección del ajuste de entrada del giradiscos Selector PHONO Ajuste el selector PHONO en función del cartucho del giradiscos. Español Opciones para cartucho del giradiscos Pulse el interruptor EXT. DIRECT. El indicador EXT. DIRECT se iluminará. El ajuste del selector INPUT se desactivará, y la entrada de fuente de audio desde los jacks EXT. IN se emitirá por una pareja de los jacks de salida.
Filtro subsónico Active el interruptor SUBSONIC FILTER para aplicar el filtro subsónico, en caso necesario. Un brazo fonocaptor de giradiscos resonante o un disco de vinilo combado pueden provocar una reverberación de frecuencia muy baja (ruido subsónico) que podría aplicar carga y daños a los altavoces. Un filtro subsónico cortará dicho ruido para proteger los altavoces. Ajuste del nivel de volumen Ajuste la ganancia usando el selector GAIN para poder realizar ajustes precisos del volumen.
Ajuste del tono Bajada momentánea del nivel de volumen Ajuste el balance de nivel de volumen entre los altavoces izquierdo y derecho usando el control BALANCE. Español Pulse el interruptor AUDIO MUTE para reducir el nivel de volumen actual 20 dB aproximadamente. Pulse el interruptor de nuevo para reponer el nivel de volumen anterior. Ajuste el nivel de volumen de las gamas altas y bajas usando los controles BASS y TREBLE.
Conexión de auriculares Si hay auriculares conectados al jack PHONES, no se emitirá ninguna señal por los jacks de salida (jacks de salida BAL, LINE 1 y LINE 2) en el panel trasero. Utilice el selector TRIM para cambiar la ganancia del amplificador de auriculares de modo que pueda ajustar el balance de nivel entre la salida de audio del jack PHONES y los altavoces para evitar cambios repentinos de volumen. Nota Si se selecciona EXT. DIRECT, no se emitirá ninguna señal por el jack PHONES.
Español Materiales de referencia 73
Especificaciones generales Tensión de salida nominal/impedancia de salida (entrada a 200 mV, de 20 Hz a 20 kHz, THD 0,01%) BAL (BYPASS). . . . . . . . . . . . . . . . . . . 2 Vrms/150 Ω BAL (ATT. −6dB). . . . . . . . . . . . . . . . . 1 Vrms/150 Ω LINE 1/LINE 2. . . . . . . . . . . . . . . . . . . 1 Vrms/150 Ω LINE 2 OUT (grabación) . . . . . . 200 mVrms/1,2 kΩ Distorsión armónica total más ruido (JEITA, entrada 0,5 V, de 20 Hz a 20 kHz) BAL 1/BAL 2/TUNER/CD/LINE 1/LINE 2 IN → BAL/LINE 1/LINE 2 . . . . .
Potencia de salida nominal de la toma de auriculares (1 kHz, 32 Ω, 0,2% THD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 mW + 35 mW Desviación de ecualización RIAA MC/MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0,5 dB Características del filtro subsónico Español MC/MM . . . . . . . . . . . . . . . . . . . . . . . . . 15 Hz/−3 dB Alimentación [Modelos para EE. UU. y Canadá]. . . . 120 V CA, 60 Hz [Modelo para China]. . . . . . . . . . . . 220 V CA, 50 Hz [Modelo para Corea]. .
EXT. IN LINE 2 OUT (recording) TUNER /CD LINE 1/ LINE 2 PHONO PHONO BAL 2 BAL 1 INPUT SUB TRANSFORMER POWER RELAY Relay BAL→UNBAL ±32V ±81V INDEPENDENT CONSTANT BASS MIDDLE TREBLE VOLUME TONE CONTROL +99V +12V CURRENT POWER SUPPLY TOROIDAL TRANSFORMER SUBSONIC ON / THROUGH TONE CONTROL ON / THROUGH INDEPENDENT REGULATED POWER SUPPLY (for AUDIO) MOTOR VOL/ RELAY BAL Normal / UNBAL: 18.6dB BAL ATT: 12.
Características de audio Respuesta de frecuencia (control de tono) 14 10 +10dB 8 +8dB 6 +6dB 4 +4dB 2 +2dB 0 ±0dB Español Response (dB) 12 –2dB –2 –4dB –4 –6dB –6 –8dB –8 –10dB –10 –12 –14 10 20 30 50 100 200 300 500 1k 2k 3k 5k 10k 20k 30k 50k 100k Frequency (Hz) Distorsión armónica total (PHONO) 10 5 2 1 0.5 THD + N Ratio (%) 0.2 0.1 20 Hz 0.05 1 kHz 20 kHz 0.02 0.01 0.005 0.002 0.001 0.0005 0.0002 0.
Filtro subsónico 10 5 THROUGH Response (dB) 0 –5 ON –10 –15 –20 –25 5 10 20 30 50 100 200 300 500 1k 2k 3k 5k 10k 20k 30k 50k 100k Frequency (Hz) · Curva de volumen 10 0 GAIN selector: –6 dB –20 Volume Level (dB) GAIN selector: 0 dB –40 GAIN selector: –12 dB –60 –80 –100 –110 0.00 50.00 100.00 150.00 Volume control (degree) 78 200.00 250.00 300.
Resolución de problemas Consulte la tabla siguiente si esta unidad no funciona bien. Si las instrucciones siguientes no ayudan a solucionar el problema, o si el problema no es uno de los que aparecen en la siguiente lista, apague la unidad, desconecte el cable de alimentación y póngase en contacto con el centro de servicio o distribuidor Yamaha autorizado más cercano.
Problema Causa Solución Consulte la página Conexiones incorrectas de los cables de entrada o salida. Conecte los cables correctamente. Si el problema persiste, es posible que los cables estén defectuosos. 60 El giradiscos no está conectado a tierra en el terminal GND. Conecte el giradiscos al terminal GND de esta unidad. 62 Se están utilizando simultáneamente cables balanceados y de línea entre dos componentes. No utilice cables balanceados y de línea simultáneamente entre dos componentes.
Índice L Activación, conexión . . . . . . . . . . . . . . . . . . . . . . . Ajuste de la entrada del giradiscos . . . . . . . . . . . . . Altavoz de subgraves, conexión . . . . . . . . . . . . . . . Amplificador de potencia, conexión . . . . . . . . . . . . ATTENUATOR, selector . . . . . . . . . . . . . . . . . . . . AUDIO MUTE, interruptor . . . . . . . . . . . . . . . . . . Auriculares, conexión . . . . . . . . . . . . . . . . . . . . . . . AUTO POWER STANDBY, interruptor . . . . . . . .
Español
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.