AX16-AT AUDIO EXPANSION CARD Owner’s Manual Mode d’emploi Bedienungsanleitung Manual de instrucciones YAMAHA CORPORATION M Pro Audio Division, #18/3 P.O.
COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: YAMAHA CORPORATION OF AMERICA 6600 Orangethorpe Avenue, Buena Park, Calif. 90620 U.S.A. 1-714-522-9011 1-714-739-2680 AUDIO EXPANSION CARD AX16-AT This device complies with Part 15 of the FCC Rules.
Important Notices • Do not place the AX16-AT in an area subject to excessive heat, direct sunlight, excessive humidity, or dust. • Keep the AX16-AT inside its antistatic bag until you are ready to install it. • To prevent handling damage, hold the AX16-AT by the edges or bracket. • If you accidentally touch the card edge connections, remove any fingerprints using a dry tissue.
Introduction Introduction Thank you for purchasing the Yamaha AX16-AT Audio Expansion Card. The AX16-AT is an ADAT format digital interface card for the Yamaha DS2416 Digital Mixing Card.
Controls & Connections 5 Controls & Connections Rear A IN 1 OUT 2 ADAT 3 THRU 4 IN 5 A A IN Signals arriving at this ADAT MultiChannel Optical Digital input are fed through to the IO-A connector on this card. B A OUT Signals from the IO-A outputs on the DS2416 are output via this ADAT MultiChannel Optical Digital output. C A & B ADAT/THRU switches These switches are used to select the input and output signals for the IO-A and IO-B connectors on this card. IO-A and IO-B can be set individually.
Controls & Connections Internal 23 45 [ THROUGH IO-A ] THRU-A A A A HALF FULL [ THROUGH IO-B ] THRU-B B B B B [ THROUGH IO-B ] IO-B B B OFF A [ THROUGH IO-A ] IO-A A A 1 (PCI mounting) A HALF/FULL switches These switches are used to configure wordclock operation when the DS2416 is used as a wordclock slave and receives its wordclock from the AX16-AT. IOA and IO-B can be set individually.
Controls & Connections 7 C IO-B connector This connector connects to the IO-B connector on the DS2416 using the supplied 20-pin connection cable. D THRU-A connector This connector connects to the first AX44 Audio Expansion Unit using the 20-pin connection cable supplied with the AX44. E THRU-B connector This connector connects to the second AX44 Audio Expansion Unit using the 20-pin connection cable supplied with the AX44.
System Hookup Overview System Hookup Overview The following diagram shows how the AX16-AT connects to the DS2416 and AX44s. Also shown are two digital multitrack recorders with ADAT format inputs and outputs for up to 16 channels of digital audio transfer between them and the DS2416.
Installing the AX16-AT 9 Installing the AX16-AT The AX16-AT installs into a single PCI or ISA expansion slot and requires no special jumper settings or interrupt settings. If you are installing in an ISA slot, see “Fitting the ISA-bus Mounting Bracket” on page 10 before continuing with this procedure. See your computer’s manual for full details on installing cards. 1 Turn off the computer and disconnect the power cord. 2 Remove the computer’s cover.
Installing the AX16-AT 6 Connect the AX16-AT IO-A connector to the DS2416 IO-A connec- tor using the supplied 20-pin cable (connect the end with the ferrite core to the DS2416). 7 Connect the AX16-AT IO-B connector to the DS2416 IO-B connec- tor using the supplied 20-pin cable (connect the end with the ferrite core to the DS2416). 8 If you are using an AX44, connect the AX16-AT THRU-A connector to the first AX44 using the 20-pin cable supplied with the AX44.
Selecting the I/O Source for the DS2416 11 Selecting the I/O Source for the DS2416 The ADAT/THRU switches select the input and output sources for the IO-A and IO-B connectors on the DS2416. In the ADAT position, the DS2416 receives and transmits signals via the ADAT IN and OUT connectors on the AX16-AT, as shown in the following diagram. In the THRU position, the DS2416 receives and transmits signals via the AX44s. IO-A and IO-B can be switched independently.
Specifications Specifications General Sampling rate External 40.013 kHz to 50.880 kHz ADAT/THRU switches DS2416 I/O source selection WORDCLOCK HALF/FULL switches Wordclock source select PCI-bus (for power supply only) PCI Raw Variable Height Short Card (5 V, 32-bit) ISA-bus (for power supply only) ISA card (5 V, 8-bit) Power supply +5 V (250 mA max) Maximum power consumption 1.25 W Temperature Operating +10˚C to +35˚C Storage –20˚C to +60˚C Dimensions (H x L x D) 125.9 (ISA 127.
Specifications Dimensions PCI 21.6 188 A A 3.1 A [ THROUGH IO-A ] A A A HALF B B OFF ADAT FULL OUT [ THROUGH IO-A ] IO-A THRU-A A IN THRU-B B [ THROUGH IO-B ] B IN [ THROUGH IO-B ] IO-B 125.9 THRU OUT B B B ISA 188 21.6 3.1 B B B OUT B [ THROUGH IO-B ] B IO-B THRU-B [ THROUGH IO-B ] IN B B THRU OFF 127.