HiFi Began with Yalllaha Yamaha's involvement with and passion for music goes back more than a century, to when we built our first reed organ in 1887. Now we are the world's leading producer of pianos and other musical instruments, and are involved with music in many other ways as well. We manufacture professional recording equipment, we design concert halls and we assist artists at concerts with set up and sound tuning. This knowledge and experience benefits our production of audio components in many ways.
Excellence in Audio Achievement 1920- j First HiFi System introduced in 1920 We introduced numerous HiFi components (turntables, FM/AM tuners, integrated amplifiers, preamplifiers, power amplifiers and speakers) in 1955 - 1965. NS-2D CA·10DO NS-69D NS-l0DOM Natural Sound Speaker Series introduced in 1967 NS-20 Monitor Speaker 1970s t CA-1000 Integrated Amplifier i Featuring A-Class operation, the CA-l 000 set the standard for integrated amplifiers.
A-52000 • Fullfloating and balanced circuit design achieves for the first time the fullpo~ntialofanawgueamplij1cation An entirely new floating and balanced power amp achieves complete symmetry and permits full balanced transmission (amplification) from the input jack to just before the speaker jack • Full-stage balanced signal transmission The world's first integrated amp to offer full stage balanced transmission, combining high power output with good sound texture and outstanding SIN performance • Floati
• Front panel (left side) @YAMAHA o POWER ~ SPEAKERS PHONES - - - TRIM rO ~." 71- . O~A+B 'lJ,LV"~"' '~' I I '---11---r--11y-11--1---I~I~ I I cb 0 c1 I ® @ G) POWER ® Press upward or downward to turn on or off this unit. Receives signals from the remote control. The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit during operation.
., @ PHONES jack Outputs audio for private listening with headphones. Note When headphones are plugged in: - Both speaker sets connected to the SPEAKERS LlR CH A and B terminals are turned off. No signals are output at the PRE OUT jacks, while signals are output at the REC jacks. You cannot select MAIN DIRECT as the input source. If headphones are plugged into the PHONES jack while MAl DIRECT is selected as the input source, no audio is output at the PHONES jack.
• Front panel (right side) @YAMAHA BASS o + .i-i-7., 'J,- , ,~, _.f' '---or-------r------------I--- 1 ® BASS Increases or decreases the low frequency response. The 0 position produces a flat response. Control range: -10 dB to + 10 dB (J) TREBLE Increases or decreases the high frequency response. The 0 position produces a flat response. Control range: -10 dB to + I0 dB Notes • When both the BASS and TREBLE controls are set to the 0 position, audio signal bypasses the tone control circuitry.
INPUT TREBLE BALANCE VOLUME CDBAl o MAIN DIRECT 0 0 + 0 OPHONO 0 l R 0 PHONO AUDIO MUTE MM MC 7 8 9 10 @ INPUT selector Selects the input source you want to listen to. The audio signals of the selected input source are also output at the REC jacks. Notes • Switch to the CD SAL position to select the CD player connected to the CD SAL jacks (balanced XLR jacks). • Switch to the CD position to select the CD player connected to the CD jacks (unbalanced RCA jacks).
A-52000 Controls andfunctions • Rear panel ep ® I I II I I I ~ I SPEAKERS R CH I±J CD SAL EJ TUNER CD LINE 1 PB REC @)@) @)@ ®® ®® ®@) ®@) @ lID I±J LINE2 III III lID lID--III EJ GND PHONO See page 14 for connection information. CD SPEAKERS LlR CH terminals ® INPUT jacks @ L1NE2 jacks @ MAIN IN jacks Note Adjust the volume level using the volume control on the external amplifier connected to the MAIN DIRECT jacks when you select MAIN DIRECT as the input source.
4 5 SPEAKERS L CH MAIN IN VOLTAGE SELECTOR I±I PRE OUT ~®@) 7 6 2~V CD EJ un®@) ACIN I±I ~ EJ r--------(8 ® ACIN Use this inlet to plug in the supplied power cable. (j) VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging the AC power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard.
A-S2000 Controls andfunctions • Remote control CDI--------. G) Amplifier control buttons INPUT Selects the input source you want to listen to. Notes • When MAIN 01 RECT is selected as the input source, no signals are output at the PRE OUT and REC jacks. • If headphones are plugged into the PHONES jack while MAl DIRECT is selected as the input source, no audio is output at the PHONES jack. I VOL +/- Controls the volume level.
A-52000 Connections Speakers A (R channel) @) CD player with RCA jacks CD player with XLR jacks Tuner e e e ===c:::=::J o 0 00U 00 fl- 0 0 a = 0000000 © + :=:::=-;'=;;;;;7,:-=:I:---:======I=~=;;:;;;;;==I==~~I\'----- ~+~SPEAK®EARSRCH_E!L~------==--'NPUT_:1. Im~5= ®®I. ~t, ~--- ·((2l@@8 ~-~-~-NO-@)' '_0 ------;·;;;;;;;~I~~~-PHONo-t-r---I--CI~F Speakers B (R channel) .I I 10 L . -_ _- ' Turntable ~o . . oo I DVD player, etc.
Preamplifier, AV receiver, etc. External amplifier or active subwoofer @ a o o @ '-,,-----.-----J Speakers A (L channel) + ------------1"L- 1- - - - 1- - - - - - - - - - - 1- - - /. /: ..... ~~rn@@ 8~~ @@Jw@@ ~®~ffi B~ AC IN [8] + Speakers B '-----_ _-----' (L channel) CD recorder, tape deck, etc. Caution • Because the power amplifier of A-S2000 is of the floating balanced type, the following types of connections are not possible.
A-S2000 Connections • Connecting the speakers • Connecting the banana plug (Except for Europe models) 1 Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and twist the exposed wires of the cable together to prevent short circuits. 10 mm 2 3 (0'4In)I~ .. First, tighten the knob and then insert the banana plug into the end of the corresponding terminal. ~ Unscrew the knob and then insert the bare wire into the hole.
• Bi-wire connection The bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. This split connects the mid and high frequency drivers to one set of terminals and the low frequency driver to the other pair. • Connecting to the CD BAL jacks Connect your CD player with the XLR balanced output jacks.
A-52000 Connections • VOLTAGE SELECTOR (Asia and General models only) Caution The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. Rotate the VOLTAGE SELECTOR clockwise or counterclockwise to the correct position using a straight slot screwdriver. Voltages are as follows: ........................
A-52000 Specifications POWER SECTION CONTROL SECTION • Minimum RMS Output Power (S 0,20 Hz to 20 kHz, 0.02% THO) (40,20 Hz to 20 kHz, 0.02% THO) .. • Dynamic Power (IHF) (S/6/4/2 Q) 90 W + 90 W 150 W + 150 W 105/135/190/220 W • Maximum Output PO\\'er (I kHz, 0.7% THO, 4 Q) [U.K. and Europe models only] 160 W • Maximum Useful Output Power (.IEITA) (I kHz, 10% THO, S/4 Q) [Asia, General, China and Korea models only] ....... 120/190 W • Dynamic Headroom SO .. .. 0.67 dB • IEC Output Power [U.K.
E ~ ~ C) ... '0 e.> .:l:- .2 m • m : h 0 0\ ~ EQAMP ' : BUFFER AMP . ;]1....... O. I I TONE CONTROL DEViCES VOLUME & TONE CONTROL ¢ ~ / J> TONE CONTROL DEVICES 1/ I ~ ~I/ TT.4 ~ k:---l~1 T ~ ~ ~I/ / [Ip ~ ~I/ I, I I I I ~ HOT BALANCE ",. UNBALANCE CONVERTER r-q f? w o z o izO o ~ 1 kc-1~I, M± ~ [tll>TI ~~ [tll> m ,~, :~ : '--'<''''''-''''''-'-'- '.. .I.. · : BUFFER AMP '"~, ~""'"'''-W r---::: ~ .I ",.~ C>- '''MMiM'C' , Q-,ro","".. CD i~ @O\,
A-52000 Specifications • Tone control characteristics +15 +12.5 +10 +7.5 CD _ __. +5 ~ :-s.U---... Y~-- +2.5 OJ Ul C ~. 0 0 Q. --~ ... .. -2.5 Ul OJ 0: -5 -7.5 -10 -12.5 -15 10 20 50 100 200 lk 500 2k 5k 10k 20k 50k 100k Frequency (Hz) • Total harmonic distortion __ -__ ---0- _.• • . •.••.•... .••• --- .... --_.- -_. ----~ .~ .......:. 0.5 f···············;············;·······+·····,·····,·..-;·· .., 0.2 ~ .~ 0.
• Total harmonic distortion (PHONO) 10 5 ----_.-:.::::-:- :::::::::::::::::: : :::;:: ~::;::::: ::::::: ::::: :::::::f:·:::I:::: •••• .-----.- -------',' •-•-, ::: :: :.: : : ~ : ::: : f: ::~:: :::: ~: :;:: :::-_: :::::: ::::::::': ----'," - .-------'," 1- 2 1 --_._-------- -----_ 0.5 _-_ -_.'- .. --_. ...... ------_..... _ "'" . . . ::: ::::::: -- - - -. --- --..... ... .. - ::: -_. - --- --- -~- .. :::::~:~:::: -~ . ~. -~ ~ ::t:j:.:.( ~ ~ 0 ~ a: z 0.2 0.1 0.05 + 0.
A-S2000 Troubleshooting Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, tum off this unit. disconnect the AC power cable, and contact the nearest authorized Yamaha dealer or service center. Problem This unit fails to turn on. Cause Remedy See page The AC power cable is not connected to theAC I inlet on the rear panel or not plugged in the AC wall outlet.
Problem Cause Remedy The volume level is low while playing a record. Incorrect setting for the PHONO switch on the front panel. Switch the PHONO switch to the MM or Me position according to the type of magnetic cartridge of the turntable. The sound is degraded when listening with the headphones connected to the CD player connected to this unit. The power of this unit is turned off. Turn on the power of this unit. The remote control does not work or function properly. Wrong distance or angle.
_YAMAHA A-S2000 Nederlands Supplement to the specifications (Page 20 in OWNER'S MANUAL) • Maximum Input Signal CD BAL Aanvulling op de technische gegevens (Bladzijde 20 in de GEBRUIKSAANWIJZING) 2.8 V • Maximum ingangssignaal CD BAL 2,8 V Supplement aux caracteristiques techniques (Page 20 du MODE D'EMPLOI) npMnO>KeHMe K TeXHM"IeCKMM XapaKTepMCTMKaM (CTp.
_YAMAHA I Note on transport tape A-S2000/CD-S2000 English Opmerking over het plakband voor het vervoer Nederlands Upon shipment from the factory, magnet feet are fixed with transport tape to this unit's feet. Remove the transport tape before placing this unit. I Remarque sur Ie ruban adhesif In de fabriek zijn de magnetische voetjes met plakband vastgezet aan de voetjes van het toestel. Verwijder dit plakband voor u het toestel neerzet.
SAFETY BROCHURE BROCHURE SUR LA SECURITE
IMPORTANT SAFETY INSTRUCTIONS & CAUTION l- RISK OF ELECTRIC SHOCK DO NOT OPEN ----' CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION (for US customers) IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirelllents. Moditications not expressly approved hy Yamaha Illay void your authority. granted hy the FCC. to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST he used. Follow all installation instructions.
Caution: Read this before operating your unit. 2 J ~ S 6 7 8 9 10 II 12 IJ 14 15 16 17 18 To assure the finest performance. please read this manual carefully, Keep it in a safe place 1'01' future reference. Install this sound system in a well \'entilated. cool, dry. clean place - away from direct sunlight. heat sources. vibration. dust. moisture. andlor cold. Allow ventilation space of at least 30 cm on the top. 20 cm on the len and right. and 20 Clll on the back of this unit.
• Notes on batteries Change all of the batteries if you notice that the operation range of the remote control decreases. Use AA, R6, UM-3 batteries. Make sure that the polarities are correct. See the illustration inside the baltery compartment. Rcmove the batteries if the n:mote control is not used for an extended period of time. • Do not use old batteries together \\'ith ncw ones. Do not use diflerent types of batteries (such as alkaline and manganese batteries) together.
_YAMAHA © 2008 YAMAHA CORPORATION All rights reserved. YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE .. BUENA PARK. CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE .. SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G,m.b.H. SIEMENSSTR 22-34. 25462 RELLINGEN BEl HAMBURG, GERMANY ELECTRONIOUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD.
YAMAHA Homc Audio products are designed and manufactured to provide a high level of trouble-free performance. YAMAHA Electronics Corporation, USA, is proud of the experienced craftsmanship Ihal goes into each and every YAMAHA Home Audio product. YAMAHA sells ils Home Audio producls only through a nelwork of high quality, specially authorized dealers and is pleased to offer the following Limited Warranty, which applies only 10 products purchased from our authorized dealers.