Integrated Amplifier Owner´s Manual
Thank you and congratulations on your purchase of this Yamaha product. • You can enjoy the high-quality stereo sound of this integrated amplifier at home. • To use the product properly and safely, we suggest that you read this manual and the “Safety Brochure” thoroughly. Keep the manual in a safe, accessible place for future reference.
Things to know before using this product About this manual • This manual describes the unit’s features and connection procedures. • The illustrations as shown in this manual are for instructional purposes only. • Specifications and appearance are subject to change without notice. • “ WARNING” describes precautions to be followed to avoid the possibility of serious injury or even death. • “ CAUTION” describes precautions to be followed to avoid injury.
Part Names and Functions This section lists the names and describes the function of various parts on the front and rear panels, and the remote control.
Part Names and Functions Front panel 123 4 5 6 1 A (Power) switch/indicator A (Power) switch NOTICE Power status On Indicator Lit brightly Up position Down position 7 Standby Lit dimly Off Off If you plan not to use the unit for an extended period of time, be sure to unplug the power plug from the AC outlet. Even when the power is turned off, a minimal amount of electric current is still flowing to the unit.
5 SPEAKERS selector Switches sets of speakers connected to the SPEAKERS L/R CH A and B terminals on the rear panel as follows: OFF: No audio signals will be output from the speakers. A: Audio signals will be output from the set of speakers connected to the A terminals. B: Audio signals will be output from the set of speakers connected to the B terminals. A+B BI-WIRING: Audio signals will be output from the sets of speakers connected to the A and B terminals.
Part Names and Functions Front panel 8 8 BASS control Adjusts the volume level of the bass range. Adjustable range: −10 dB – 0 – +10 dB 9 TREBLE control Adjusts the volume level of the treble range. Adjustable range: −10 dB – 0 – +10 dB 0 BALANCE control Adjusts the audio output balance between the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions.
B C D E Note • If MAIN DIRECT is selected as the input source, audio signals will not be output at the PRE OUT, LINE 2 OUT or PHONES jacks. • If LINE 2 is selected, audio signals will not be output at the LINE 2 OUT jacks. B PHONO switch Set this switch to the MM or MC position according to the type of magnetic cartridge of the turntable connected to the PHONO input jacks on the rear panel. C Feet If the unit is unstable, adjust the height of the feet as needed by rotating them.
Part Names and Functions Rear panel 1 7 8 1 BAL (balanced) input jacks Note Set the ATTENUATOR selector and PHASE selector appropriately for the playback component that is connected to these jacks. (➔ page 20) 2 PRE OUT jacks Note • Audio signals output at the PRE OUT jacks are the same channel signals that are output at the SPEAKERS L/R CH terminals. • The following parameter settings are effective for audio signals output at the PRE OUT jacks.
3 4 5 7 6 E 9 PHONO input jacks 0 CD input jacks A GND (Ground) terminal If you connect your turntable to this unit, ground it to the GND terminal. Doing so may reduce noise. CAUTION Do not loosen the GND terminal knob excessively. Otherwise, the knob may come off and a child may swallow it accidentally. D MAIN IN jacks Connect external components that feature a volume control function so that you can use this unit as a power amplifier.
Part Names and Functions Remote control 1 Infrared signal transmitter 1 Outputs infrared control signals toward the unit. (➔ page 14) 2 A AMP key Turns on the power to the unit or switches it to standby mode. (➔ page 6) 2 3 Input select keys Select the input source. Audio signals of the selected input source will be output at the LINE 2 OUT jacks. 3 BAL: Selects the component connected to the BAL input jacks as the input source.
6 Tuner control keys Control the functions of a connected Yamaha tuner. For more information, refer to the owner’s manual for your tuner. 7 CD player control keys Control the functions of a connected Yamaha CD player. For more information, refer to the owner’s manual for your CD player. OPEN/CLOSE key: Opens or closes the disc tray of a connected CD player. A CD key: Turns on the power to a connected CD player, or switches it to standby mode. (Play): Starts playback of the CD player.
Part Names and Functions ■ Installing batteries in the remote control 1 Remove the battery compartment cover. ■ Operating the remote control Operate the remote control in the range shown below by pointing it toward the remote control sensor on the front panel of the unit. 2 Insert two batteries (AAA, R03, UM-4) according to the polarity markings (+ and −) on the inside of the battery compartment. Within 6 m 30 1 2 3 Reinstall the battery compartment cover.
Connections This section explains how to connect the unit to speakers and audio source components.
Connections Connection diagram CAUTION Be sure to complete all connections before plugging in the power cable to an AC outlet. (➔ page 22) CD player or network player featuring XLR jacks (➔ page 20) CD player featuring RCA jacks Tuner Speaker A (R channel) (➔ page 18) + - + - Speaker B (R channel) (➔ page 18) Turntable 16 BD player, etc.
NOTICE If a component is connected to the MAIN IN jacks, the unit’s volume level will be fixed. Therefore, do not connect a CD player or other components that do not feature volume adjustment to the MAIN IN jacks. Otherwise, a loud sound may be emitted, resulting in malfunction of the unit or damage to the speakers. External amplifier or active subwoofer Speaker A (L channel) - + – + Speaker B (L channel) CD recorder, tape deck, etc. Preamplifier, AV amplifier, etc.
Connections Connecting speakers ■ Using speaker cables Note • Because this power amplifier is of the floating balanced type, the following connections are not possible. - Connecting between two “+” (or two “−”) terminals of the left and right channels (Fig. 1). - Connecting each “−” terminal of the unit’s left and right channels to the opposite channel speakers (cross connection, Fig. 2).
Bi-wired connection Note All connections must be correct: L (left) to L, R (right) to R, “+” to “+”, and “−” to “−”. For information regarding the connection procedure, refer to the owner’s manual for your speakers. ■ Using banana plug cables (Models for U.S.A., Canada, Australia, China, and Taiwan) First tighten the knob on the SPEAKERS terminal, and then insert the banana plug into the head of the knob. A bi-wired connection separates the woofer from the mid and high ranges.
Connections Balanced connection Trigger connection You can connect a CD player or network player that features XLR-type balanced output jacks to the BAL input jacks of this unit. Use XLR-type balanced cables for this connection. ATTENUATOR selector: Enables you to set the allowable input level at the balanced input jacks. Select ATT. (−6 dB) if the audio output from the connected component sounds distorted.
Remote connection ■ Operating the unit from another room If you connect a commercially-available infrared receiver and transmitter to the unit’s REMOTE IN/OUT jacks, you will be able to operate the unit and/or external component from another room, using the supplied remote control. Rear panel of this unit ■ Remote connection between Yamaha components If you have another Yamaha component that supports remote connections, an infrared transmitter is not necessary.
Connections Connecting the power cable After all connections are complete, plug the power cable into the AC IN connector of the unit, and then plug the power plug into the AC outlet.
Appendix This section lists technical specifications for this unit.
Appendix Specifications Rated output power (20 Hz to 20 kHz, 0.07% THD) 2-channel driven [Model for Asia] 8Ω ............................................................ 90 W + 90 W 6Ω .........................................................110 W + 110 W [Other models] 8Ω ............................................................ 90 W + 90 W 4Ω ........................................................ 150 W + 150 W Maximum input / signal voltage (1 kHz, 0.5% THD) PHONO (MC)...............................
Channel separation (JEITA, 1 kHz/10 kHz) PHONO (MC)..................................66/77 dB or higher PHONO (MM).................................90/77 dB or higher CD (or similar)/BAL........................74/54 dB or higher * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website and download the manual file. Tone control characteristics BASS Boost/cut .................................................
SUB TRANSFORMER LINE AMP POWER RELAY POWER SUPPLY FOR CONTROL CONSTANT CURRENT POWER SUPPLY FOR AUDIO PREOUT AMP LINE2 OUT AMP INPUT SELECTOR MM EQ AMP MC HEAD AMP PHASE CHANGE (normal/inv.
Acoustic characteristics ■ Tone control characteristics 14 12 10 8 6 Response (dB) 4 2 0 –2 –4 –6 –8 –10 –12 –14 10 20 30 50 100 200 300 500 1k 2k 3k 5k 10k 20k 30k 50k 100k Frequency (Hz) ■ Total harmonic distortion 1.000 0.500 0.200 THD + N Ratio (%) 0.100 0.050 20kHz 0.020 20Hz 0.010 0.005 1kHz 0.002 0.
Appendix ■ Total harmonic distortion (PHONO) 10 5 3 2 1 THD + N Ratio (%) 0.5 0.3 0.2 0.1 0.05 20Hz 0.03 0.02 1kHz 20kHz 0.01 0.005 0.003 0.002 0.001 0.0005 0.0003 0.0002 0.
Troubleshooting Refer to the table below if this unit does not function properly. If the instructions below do not help, or if the problem you are experiencing is not listed below, turn off the unit, disconnect the power plug, and contact the nearest authorized Yamaha dealer or service center. Problem Cause Remedy See page The power cable is not connected to the AC IN connector on the rear panel or is not plugged into an AC outlet. Connect the power cable firmly.
Appendix Problem Cause Remedy See page The + and − wires are connected in reverse at the amplifier or the speakers. Connect the speaker wires to the correct + and − phase. 18 Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables might be defective. 16 The turntable is not grounded to the GND terminal. Connect the turntable to the GND terminal of this unit.
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads https://download.yamaha.