9000 Pro USB Interface Installation and Operating Manual 1. Installation Manual 2. Installation of the Windows Drivers 3. Operating Manual 4. Applications Important Notice: Only a qualified service technician should install the USB Interface. We cannot be held responsible or liable for direct or indirect damage caused by incorrect installation of the USB Interface board. ©2001 musitronics GmbH – Ver. 05.25.
1. Installation Congratulations on having purchased an accessory which, we believe, will change the way you use your keyboard, and will open a new world of creative possibilities and ease of use. We have done our best to produce a reliable product, which will give you many years of satisfaction. We hope you enjoy it. 1.
The process of keeping small parts in alignment will be much easier if you now place a small piece of masking tape over the head of each screw and press it in place against the cover, to prevent the screws from falling out during assembly. Turn the plate over and slip one of the short, black plastic spacers over each of the four threaded screws and down against the cover.
Figure: USB Board assembly: Metal cover HD-cable 9000PRO Flat cable Harddisk If you look into the open plug-in board/hard disk compartment, you will see a thick bundle of wires running along the forward inside edge, held in place by a black retainer band, bent around them. To assure clearance of your new parts, it might be advantageous to bend the retainer open and free the wiring bundle slightly, so it can be moved a bit, if necessary, to make room for the new components.
Remove the six retaining screws from the SIMM Cover, where optional RAM memory chips may be mounted (See illustration below.) and set the cover aside. Feed the socket end of the USB cable from the new Interface through the space between the two open compartments and out through the opening of the SIMM compartment. If your kit includes a new SIMM cover, with mounting holes for the USB plug, you may set aside or discard the old cover.
Simm cover USB connector position (See illustration above.) The best mounting position is on the angled surface along the left edge of the cover, looking at it as above (circled area). There must be adequate clearance between the socket and any mounted optional SIMMs. This should be no problem. Drill three holes in the metal cover, marking locations by printing the following illustration and using it as a template: Carefully mark and drill all three holes with a 3mm (or 1/8 inch) drill bit.
2. Driver Installation under Windows 2.1 Driver Installation under Windows XP Turn on the computer, turn off your 9000 Pro, and connect both with the included USB cable. If you need more length, take the included cable along to your neighbourhood computer store and be sure you purchase a new one with the same plug connections on each end. Now turn on the keyboard. Automatic hardware detection and driver installation will begin. Pop-up windows will appear, such as “New Hardware Found”.
2.3 Driver Installation under Windows 98 and Windows 98SE Please do not install the USB Interface under any operating system earlier than Windows 98, as we cannot guarantee proper functioning of the product. To begin the installation process, with your 9000 Pro turned off, turn on and boot your computer. Then connect the two, with the supplied USB cable. 1.) Turn on the PSR9000/ 9000PRO. In a few seconds, the following message appears: “New hardware found – Musitronics USB Interface“. Click “Next”. 2.
3. Operating the PSR9000/9000Pro USB Interface Important Notice: Musitronics can not be held responsible or liable for any data loss that is caused by use of the USB Interface Do not disconnect the USB cable if a USB transmission is in progress, or else you may loose data! It is not possible for a PC and the PSR9000/9000Pro to simultaneously access the keyboard’s hard disk. Before you change from PC to keyboard or the other way around, wait until any data transmission is complete.
If you first switch on the PSR9000/9000Pro, with a USB cable connected to your computer, and then turn on the computer, this may create conflict with your computer’s Auto Load function, depending upon the type of hard disk installed. To avoid such potential problems, it would be good practice to connect the USB cable after Auto Load has been completed, or at least be sure that the 9000 is turned off before the computer is turned on. NOTE: PSR 9000 operating system Version 3.0 and 9000 Pro Version 2.
Refresh the PSR-9000 Displays After you have transferred data from the PC to the PSR-9000, you must refresh the display of your PSR-9000 to make the new data on the hard disk visible: 1) In all file menus, changing from one partition to another, or between a partition and the floppy disk, will refresh the display. 2) In the Song menu, just switching between two song displays, such as SONGII and SONGV, will also refresh the display.
Directly download MIDI music, styles, and data from the Internet to your PSR9000 Hard Disk It’s easy with the USB Interface! After you select a MIDI file or a sample from the Internet, right click on your mouse button and select “Save Target as”. Now directly select the appropriate PSR-9000 hard disk partition and its desired target folder. By saving it to that target folder, it is possible to save a MIDI song directly from Rio De Janeiro to your PSR-9000 Pro’s hard disk for replay anytime.
folder of your choice on the PSR-9000’s hard drive, via your computer’s monitor and keyboard. Defragment a partition ; Make a Compressed Backup: With full disk management capability, you can shorten access time to your PSR9000’s hard disk files by periodically defragmenting the drive, via your computer. Simply select the desired partition, right click it, and select the “Tools” tab. Click the “Defragment Now” button. On the same tab, you can check the partition or make a compressed backup.
