○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ MIDI Data Format
Effect Data Value Assign Table Table#1 LFO Frequency Table#5 Delay Time(200.0ms) Table#8 Compressor Attack Time Table#9 Compressor Release Time Data Data Data Data 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Value Data Value Data Value Data Value 0.00 32 1.35 64 2.69 96 8.41 0.04 33 1.39 65 2.78 97 8.75 0.08 34 1.43 66 2.86 98 9.08 0.YAMAHA [ Clavinova ] Model CVP-103/105/107/109/700 Date:01-MAR-1999 MIDI Implementation Chart Version : 1.0 Transmitted Recognized Remarks Function ...
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ Notes: *1: The send channel for the RIGHT1, RIGHT2, and LEFT parts can be set using the Send Channel (Keyboard) function. The transmission of accompaniment, harmony, and song data can be turned on or off using the Send Channel (Accompaniment/Harmony) and Song Transmission functions. *2: Messages received on the channel set by the Remote Keyboard function are handled as operations performed directly on the keyboard or panel.
1 A • Cardboard packing cushions • Phone jacks B • Bundled pedal cord inside C D • AC power cord CVP-103: Assembly ○○○○○○○○○○○○○○○○○○○○○○○○○ CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated above. Use of incorrect screws can cause damage.
2 • 6 x 20 mm round-head screws x4 1 • 4 x 12 mm round-head screws x2 2 • 4 x 20 mm tapping screws x4 3 • 6 x 20 mm round-head screws 1 C • 6 x 16 mm flat-head screws x4 3 X Attach the side panels (D) to the pedal box (C). Before installing the pedal box, untie and straighten out the bundled cord attached to the bottom of the pedal box. Don’t discard the vinyl tie, you’ll need it later in step B.
3 4 • 4 x 12 mm round-head screws 2 15 cm D A 15 cm D B • Be sure to place your hands at least 15 centimeters from either end of the main unit when positioning it. • 4 x 20 mm tapping screws 3 C Attach the rear panel (B). With the rear panel slightly angled as shown in the illustration, lower it onto the feet’s protruding edge at the rear of the pedal box.
5 • Cord holder • Kabelhalter • Serre-câble • Soporte del cable • 6 x 16 mm flat-head screws 4 • Use the vinyl tie that was removed from the bundled pedal cord in step X to tie up any slack in the pedal cord. A D B Connect the pedal cord. The pedal cord from the pedal box must be plugged into the PEDAL connector on the rear of the main unit. Once connected, attach the cord holders to the rear panel as shown, then clip the cord into the holders.
6 7 C 220 240 110 127 • A voltage selector is provided in some areas. N Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped.
CAUTION • Models without keyboard cover • When moving the instrument after assembly, always hold the lower surface of the main unit, NEVER the top portion or keyboard cover. Improper handling can result in damage to the instrument or personal injury. • Models with keyboard cover ■ After completing the assembly, please check the following. • Are there any parts left over? ➔ Review the assembly procedure and correct any errors.
1 • AC power cord • Phone jacks • Cardboard packing cushions • 5 x 12 mm screws x 30 CVP-105: Assembly ○○○○○○○○○○○○○○○○○○○○○○○○○ CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated above. Use of incorrect screws can cause damage.
2 3 • Blanket, etc. • Three screws on each side X Carefully lean the main unit against a wall. To make it easier to install the legs, place a soft blanket or similar material on the floor near a wall, close the Clavinova keyboard cover, place the front panel of the Clavinova (the side with the keyboard) on the blanket and gently lean the unit against the wall — MAKING SURE THAT IT CAN NOT FALL — as shown in the illustration. CAUTION • Do not lay the main unit upside-down on the floor.
4 5 • Four screws on each side • Cord holder • Vinyl tie V Attach the speaker box. Gently rest the speaker box onto the corresponding brackets on the front legs. Make sure the speaker cord is extending out from the rear of the speaker box. Loosely secure the speaker box to the main keyboard unit using four screws on both the front and back. (The speaker will be secured in step B.
6 • Six screws on each side • Two screws on each side N Secure the speaker box. Stand the main unit on its legs and securely attach the speaker box to the bracket on the front legs using two screws for each bracket. If it is impossible to align the bracket holes with the speaker box holes, slightly loosen the three screws on each of the front legs, align the holes, and secure the speaker box. After the speaker box is firmly attached, retighten the screws on the front legs firmly.
7 8 240 220 110 127 • A voltage selector is provided in some areas. M Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped.
CAUTION • When moving the instrument after assembly, always hold the lower surface of the main unit, NEVER the top portion or keyboard cover. Improper handling can result in damage to the instrument or personal injury. ■ After completing the assembly, please check the following. • Are there any parts left over? ➔ Review the assembly procedure and correct any errors. • Is the Clavinova clear of doors and other movable fixtures? ➔ Move the Clavinova to an appropriate location.
1 5 x 20 mm long screws x 20 ● Cord holders x 2 ● AC power cord A D C B ● Front leg A ● Front leg B ● Rear leg C ● Pedal box D CVP-700: Assembly ○○○○○○○○○○○○○○○○○○○○○○○○○ CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. Attempting to assemble alone is dangerous. • Be sure to use the correct screw size, as indicated above.
2 C 5 x 20 mm long screws B A 5 x 20 mm long screws Minimum space between the leg flanges and the metal frame. X Attach the three legs (A, B, C). Use scissors or a cutter to remove the packing material in which the main unit is wrapped. Then attach the legs to the bottom of the main unit using four 5 x 20 mm long screws per leg. Please refer to the illustration carefully when attaching the legs, to ensure that the positions of the (A) and (B) legs are not reversed.
3 D 5 x 20 mm long screws Keyboard Side Rear Side C Attach the pedal box (D). Before attaching the pedal box, connect the pedal cord. Pull the pedal plug out from the hole in the base plate and plug it into the socket in the bottom of the main unit with the lug on the plug facing the rear of the main unit (refer to the illustration). If the plug won’t go in properly, don’t force it … check the plug orientation and try again.
4 B A V Turn over the instrument and packing. Make sure that the three legs are firmly attached, then using the front legs (A) and (B) for support, turn over the instrument and packing so that the carton is on top of the instrument. CAUTION • Make sure that two persons are used to turn the instrument over. Holding the sides carefully turn over the instrument.
5 B Remove the carton and packing material. Lift and remove the carton, then remove the remaining packing material from the main unit.
6 7 5 x 20 mm long screws 5 x 20 mm long screws ● A voltage selector is provided in some areas. A 220 240 110 B 127 N Attach the front leg/frame screws. Firmly attach the front legs (A) and (B) to the frame on the bottom of the main unit using two 5 x 20 mm long screws for each leg. M Voltage Selector Check the setting of the voltage selector which is provided in some areas.
9 8 D D ● Cord holders < Attach the cord holders and plug in the AC cord. Remove the protective backing from the adhesive surface of the cord holders, and attach at approximately the locations shown in the illustration. Plug the main-unit end of the AC cord into the corresponding socket on the bottom of the main unit, then secure the cord with the cord holders. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area. > Set the adjuster.
CAUTION • When moving the instrument after assembly, always hold the lower surface of the main unit, NEVER the lid or keyboard cover. Improper handling can result in damage to the instrument or personal injury. ■ After completing the assembly, please check the following. ● Are there any parts left over? m Review the assembly procedure and correct any errors. ● Is the Clavinova clear of doors and other movable fixtures? m Move the Clavinova to an appropriate location.
1 • Depending upon the unit type, the unit may be packed with the cardboard packing cushions shown in the illustration. In this case, refold the cushions as shown in the illustration. Rest the main unit in a stable manner on the cushions as shown in the illustration. • Cardboard packing cushions • Phone jacks CVP109/107: Assembly ○○○○○○○○○○○○○○○○○○○○○○○○○ CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction.
• AC power cord 2 3 B A • 4 x 12 mm small screws x 4 • Blanket, etc. • 5 x 12 mm large screws x 30 C • Right leg • Left leg X Carefully lean the main unit against a wall.
4 5 CVP-109 • Three screws on each side • Four screws on each side V Attach the front legs. Securely attach the two front legs using three 5 x 12 millimeter large screws for each leg (use a Philips “+” screwdriver) as shown in the illustration. Make sure that the screws are firmly tightened. B Attach the speaker box. Remove the speaker box cover (attached to the speaker box in 6 places with plastic plugs) from the speaker box.
6 • Six screws on each side N Attach the pedal box assembly. CAUTION • When you lift the pedal box assembly, make sure that you lift by both legs. Before attaching the rear leg and pedal box assembly, insert the pedal cord plug extending from the left leg into the corresponding socket in the main unit. Make sure that the protruding clip on the connector is on the right.
7 CVP-109 • Make sure the plugs are fully inserted and there is no space left around the plugs and holes. • Two screws on each side M Secure the speaker box. Stand the main unit on its legs and securely attach the speaker box to the bracket on the front legs using two 5 x 12 millimeter large screws for each bracket. If it is impossible to align the bracket holes with the speaker box holes, slightly loosen the three screws on each of the front legs, align the holes, and secure the speaker box.
8 9 240 220 110 127 • A voltage selector is provided in some areas. < Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped.
CAUTION • When moving the instrument after assembly, always hold the lower surface of the main unit, NEVER the top portion or keyboard cover. Improper handling can result in damage to the instrument or personal injury. ■ After completing the assembly, please check the following. • Are there any parts left over? ➔ Review the assembly procedure and correct any errors. • Is the Clavinova clear of doors and other movable fixtures? ➔ Move the Clavinova to an appropriate location.
Specifications ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ KEYBOARD 88 keys (A–1 — C7) TONE GENERATOR AWM (Advanced Wave Memory) MAXIMUM SIMULTANEOUS POLYPHONY 128 (CVP-109), 64 (CVP-107/700), 64 (CVP-105), 64 (CVP-103) VOICES Clavinova voices: 224 (CVP-109/107/700), 195 (CVP-105/103) Organ Flutes voices: 6 (CVP-109/107/700) XG voices: 480 Drum Kits: 13 sets (CVP-109/107/700), 12 sets (CVP-105/103) Voice Groups: Piano, Electric Piano, Guitar, Synthesizer, Organ, Strings/Choir, Brass, Sax/Flute, Bass, Percuss
M.D.G., EMI Division, Yamaha Corporation © 1999 Yamaha Corporation V335380 909POCP6.