User’s Manual/English/ Version1.0/ Hypersound128 Navigating the User’s Manual This User’s Guide is in Adobe Acrobat (.PDF) file format. Important: We recommend that you use Adobe Acrobat Reader version 4.0 or higher to view and print the User’s Manual. Acrobat Reader 4.0 is available on this CD. Click blue, underlined text links to jump to another location in the document or to a location on the Internet. Click the Index link at the bottom of any page to go to the index of the User’s Manual.
User’s Manual/English/ Version1.0/ Hypersound128 INDEX Chapter 1 Introduction 1-1 Your Hypersound MP3 Player………. ………………………………………………….…….…………..1 1-1.1 Features ……………………………………………………………………………….……………………………..1 1-1.2 System Requirements…………………………………………………………………..…………………….1 1-1.3 In the Package…………………………………………………………………………………………………….1 1-1.4 Location of Controls………………………………………………………………………………………….…2 1-1.5 Battery……………………………………………………………………………………………………………….…3 1-1.5.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 1-1 1 Introduction Your Hypersound MP3 Player 1-1.1 Features Slim & Portable Full Function Integrated Plays WMA/MP3 Digital Music Digital Voice Recording Built-in Flash Memory Dot Matrix LCD Display Blue EL Type Back Light USB Disk Function, Upload and Download, No Limit By The File Type USB V1.
User’s Manual/English/ Version 1.0/ Hypersound 128 1-1.4 Location of Controls 9 11 10 5 3 1 8 2 6 12 4 7 1 Power ON/Play/Pause Press the button to power ON, playback music or voice file. 2 Stop/Power OFF Press to Stop the playback or Recording; Press and holding for some seconds to turn off the player. 3/4Volume +/ Press these two buttons to adjust the earphone output volume level. 5 Menu (Operation Button) The 3-way Operation button is one special button of the player.
User’s Manual/English/ Version 1.0/ Hypersound 128 6 Hold Switch Hold:When you need to lock the player buttons, slide the Hold Switch Upwards. If the player is on at this moment, the LCD will display as following when any key touch: 1 VOL A-B ROCK Song 01 / 21 m I LOVE NAPA,I’M I AM HERE HERE WAITING WAITING Richard Marx 1:3101:31 / 4:42/ 04:23 Release:You can re-operate the player only when the Hold Switch is Released. Slide the Hold Switch back to Release.
User’s Manual/English/ Version 1.0/ Hypersound 128 1-1.5 Battery The player uses built-in rechargeable battery. There is battery power capacity indicator appears on the LCD display. There are two ways to charge the battery. 1-1.5.1 Checking out the remaining power capacity Power Capacity Indicator Symbols Full Power Not Full Power Low Power Need to charge If not use the player for a long time, you may find the battery capacity becomes low.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 2 Install Software If you are using Windows Me/XP/2000, it is no need to install driver. Just connect the player to your PC, the player will be detected and install one general driver. The built-in flash memory of the player will appear in “My Computer” as one Removable Disk. After it is finished, you can upload, download and manage the files in the player.
User’s Manual/English/ Version 1.0/ Hypersound 128 Step 9. 2-2 Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Step 7. When prompted to restart your system, take out the CD from the CD-ROM drive and select the Yes, I want to restart my computer now option and then click the Finish button。 For Macintosh OS Insert the bundled CD into the CD-ROM drive. Double click on the CD-ROM icon on desktop. When the CD-ROM file list window appears, double click the MAC_OS icon.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 3 Connect to PC You need not switch off your computer when you connect the player to the PC since USB is Plug-and-Play. Before USB connecting with computer,disconnect the earphone from the player. Setup Connection (1) Position the PC so that its USB ports can be easily accessed. (Note: The USB port(s) on you PC may be found on the front panel instead of the back panel.
User’s Manual/English/ Version 1.0/ Hypersound 128 3-2 For Macintosh OS Step 8. Step 9. System detects the new hardware and one new Untitled Disk icon appears on desktop. Now you can download your WMA/MP3 music to the player by copying the files to the new Untitled Disk.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 4 Download Music The player can be used as one mobile data storage device. It needs no special software to upload, download and manage the music and files. Just using the copy, paste, delete and etc. commands of your Operation System such as Windows and Macintosh OS, it is very easy and fast by clicking the mouse. To Download Music to the Player, connect the player with PC, then: 4-1 For Windows Step 1.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 5-1 5 Starts to play Getting Started Power ON Power ON:Press the Power On button to turn on the player. ROCK VOL Song: 01 / 21 m I LOVE NAPA,I I AM HERE ’M HERE WAITING WAITING Richard RichardMarx Marx 0:00 00:00 0:00 / 0:00 / 04:32 0:00 Music / Voice / Record If you like, you can switch to playback voice memos or start to record voice. Just press the Operation Button and select voice or record in the menu list.
User’s Manual/English/ Version 1.
User’s Manual/English/ Version 1.0/ Hypersound 128 3 The LCD 1. Battery indicator 10 2. Hold key indicator 3. Play Modes indicator 4. A-B Repeat indicator 9 5. ID3 Tag display 6. Track Number 7. M: Music Mode; V: Voice Mode 8. EQ indicator 9. Volume level indicator 10. Player Status indicator 11.
User’s Manual/English/ Version 1.0/ Hypersound 128 the section to end. The player starts to playback the selected section from start to end repeatedly. To cancel the A-B Repeat, press the A-B repeat button again. The A-B repeat indicator disappears from the LCD and the music continues playing from the point. File Name Display When you select one song, the file name is displayed on LCD. And the file name will scroll from left to right if the file name is longer than the display.
User’s Manual/English/ Version 1.0/ Hypersound 128 5-6 Advanced Setting Setting the Menu Music m Settings Voice Eq Play Mode Backlight Contrast Settings Erase Files Press the Operation button to enter menu list. Shift the Operation button and select Setting. Press the button to enter Setting. There are several advanced setting options. 1、Equalizer Setting Select Equalizer in the Setting list and enter. The Equalizer (EQ) setting is to adjust the music playback effect.
User’s Manual/English/ Version 1.0/ Hypersound 128 4、Back Light In the Setting list, Select Back Light and enter. m Disable 1 seconds 3 min 2 seconds 5 mins seconds 5 mins 10 10 mins Shift the Operation button to select turn on or turn off the back light. Press the Operation button to confirm. 5、Power Saving In the Setting list, Select Power Savings and enter. m Disable 1 min 2 mins 5 mins 10 mins The Power Saving setting is to set how long after the player is idle to shut down the player automatically.
User’s Manual/English/ Version 1.0/ Hypersound 128 Step 4. Step 5. Step 6. Step 7. Step 8. You are asking if you are sure to erase the listed music file or voice memo. The file name is listed on the screen to help you decide. The selected answer Are you sure you want to is No by default. If it is not delete the file the one to erase, press the I Love NAPA here waiting I’m here waiting ,I’m Operation button. Another file is listed on the screen and Yes No you are asking if to erase this file again.
User’s Manual/English/ Version 1.0/ Hypersound 128 Chapter 6 Software Utility 6-1 Software Utility Upon the driver installation is completed, two software utilities will be installed in PC. Customer can use the utilities to format or upgrade the unit. Start>Program> Yakumo H.S 128 MP3 Player Connect the player to computer and click the corresponding program to run: 6-2 Player Format For Windows98: Click on Start button, you can format the player storage.
User’s Manual/English/ Version 1.0/ Hypersound 128 6-3 Player Update The firmware in the player will be able to update through Player Update utility running on your PC. To update the firmware, user needs to run the MP3 Player Update utility from: Start->Program-> Yakumo H.S 128 MP3 Player Check the Current Firmware Version and Upgrade Firmware Version. If you are sure it is the right version to update, click on Start button. The firmware is been updated to the player. Please wait until it is finished.
User’s Manual/English/ Version1.0/ Hypersound128 Appendix 1 Cautions Handle the player z z z z z No altering or remodeling. This can cause malfunctioning. No dropping or strong impacts This may damage the unit. Locations to be avoided Avoid using or storing the unit in following locations since they can cause malfunctioning. 1. Bathrooms and other moisture-prone places 2. Warehouses and other dusty place. 3. Very hot places near heating appliances, etc.
User’s Manual/English/ Version1.0/ Hypersound128 Appendix 2 Specifications Size (W x H x D) (Approximation) About 55 x 78 x 16 mm Memory Internal Memory (Built-in the main unit) 128MB No Memory Expansion Slot Interface USB Rev. 1.
User’s Manual/English/ Version1.0/ Hypersound128 Appendix 3 FAQ 1, Why am I unable to install the installation software to my operating system? Please note that Windows95 is unable to support USB interface properly. Please upgrade your system to Windows98 (Version 2.0, 4.10.2222 A), 2000, ME, or XP. Please note that there is no driver required for PC running Windows2000, ME, and XP (Plug and Play).
User’s Manual/English/ Version1.0/ Hypersound128 6, Why the LCD cannot display the details of the tracks? Please ensure the tracks are encoded with their ID3 tags being created as well. You may MP3 playback software such as Winamp to edit the ID3 tags of the tracks and the information must be recorded either in English or Traditional Chinese. 7, How long should I charge the battery before I use the player for the first time? Recharge the battery over 24 hours before the first time use the player.
User’s Manual/English/ Version1.0/ Hypersound128 Appendix 4 Make your own Opening Screen Step 1. Run LogoMaker.exe from CD or hard drive. Step 2. Then, if you are going to draw one opening screen manually, please skip to Step 5. If you are going to convert a photo to opening screen, please continue from Step 3. Step 3. Open source image (Click File-> Open image, then select one image file) LogoMaker supports 3 types of image file: BMP, GIF and ICO. Step 4.
User’s Manual/English/ Version1.0/ Hypersound128 Inverted Invert the color Resize Resize the source image Resize Options Maintain original aspect ratio Resize and maintain original aspect ratio of source image LCD aspect ratio Resize in LCD aspect ratio Best fit LCD screen Resize by program automatically Rotation 90 deg. Rotate source image by 90-degrees clockwise Left window will demo what the opening screen will be. When you have finished configure, click Convert Single or Convert All.
User’s Manual/English/ Version1.0/ Hypersound128 Step 5. Modify frame / set up display options of the opening screen frames Option Function Default Available value Clear screen before display current frame. No clear No Clear / Clear Setup current frame display time 0.1 sec. 0 ~ 3 sec.
User’s Manual/English/ Version1.0/ Hypersound128 FAQ & Troubleshooting 1) How can I make an animation type opening screen logo? Answer: It is easy if you have one GIF file which contains animation. Open one gif file, setup convert options, then convert the file into opening screen frames. Note: Some gif type files have only one frame, so they will be converted to a one-frame opening screen only.