VHF/UHF DUAL BAND TRANSCEIVER FT-60R/E OPERATING MANUAL YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A. YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. YAESU HK LTD. Unit 1306-1308, 13F.
Contents General Description .......................................... 1 Accessories & Options ...................................... 2 Controls & Connections ................................... 3 Top & Front Panel .......................................... 3 LCD ................................................................ 4 Side Panel ....................................................... 5 Keypad ........................................................... 6 Installation of Accessories ..............
GENERAL DESCRIPTION The FT-60R/E is a dual band FM transceiver with extensive receive frequency coverage, providing local-area two-way amateur communications along with unmatched monitoring capability. The FT-60R/E’s small size allows you to take it anywhere - hiking, skiing, or while walking around town - and its operating flexibility brings the user many avenues of operating enjoyment.
ACCESSORIES & OPTIONS SUPPLIED ACCESSORIES FNB-83 NC-88B PA-44C/U Belt Clip Antenna Operating Manual Warranty Card 7.2 V, 1,400 mAh Rechargeable Nickel-Metal Hydride Battery Pack Overnight Battery Charger (10-Hour, for USA model) Overnight Battery Charger (10-Hour, for European model) AVAILABLE OPTIONS FNB-83 FBA-25A VAC-370B/C/U NC-88B PA-44C/U CN-3 CT-27 CT-44 E-DC-5B E-DC-6 MH-34B4B MH-37A4B VC-25 7.
CONTROL & CONNECTIONS (TOP & FRONT PANEL) Antenna Jack Connect the supplied rubber flex antenna (or another antenna presenting a 50-Ohm impedance) here. VOL/PWR Knob Turn this control clockwise to turn the radio on and to increase the volume. Counter-clockwise rotation into the click-stop will turn the radio off. TX/BUSY Indicator Lamp This indicator glows green when the squelch opens, and turns red during transmit.
CONTROL & CONNECTIONS Memory Channel Number Skip Memory Channel or Preferential Memory Channel Repeater Shift Direction Dual Watch Active CTCSS/DSC Operation Automatic Power-Off Active Internet Connection Feature Active Priority Channel Memory Bank Active Bell Alerm Active Operating Mode Operating Frequency Secondary Keypad Active Key Lock Active (LCD) Battery Indicator S- & PO Meter Battery Saver Active Low TX Power Selected 4 FT-60R/E OPERATING MANUAL
CONTROL & CONNECTIONS (SIDE PANEL) PTT (Push To Talk) Switch Press this switch to transmit, and release it (to receive) after your transmission is completed. MONI/T.CALL Switch USA/EXP Version: Pressing this switch disables the noise squelching action, allowing you to hear very weak signals near the background noise level temporarily. Press the [F/W] key on the keypad first, then press this switch to “open” the squelch continuously. Press this switch again to resume normal (quiet) monitoring.
CONTROL & CONNECTIONS (KEYPAD) Primary Function (PRESS KEY) Frequency entry digit “1” Frequency entry digit “2” Secondary Function (PRESS [F/W] + KEY) Activates the CTCSS or DCS Operation Selects the CTCSS tone or DCS code number Third Function (PRESS & HOLD KEY) Recalls the “Weather” broadcast channel bank Activates the ARTS feature Primary Function (PRESS KEY) Frequency entry digit “4” Frequency entry digit “5” Secondary Function (PRESS [F/W] + KEY) Selects the direction of the uplink frequ
CONTROL & CONNECTIONS (KEYPAD) Primary Function (PRESS KEY) Frequency entry digit “3” Increases the VFO frequency by one step or moves the memory channel to the next-highest channel Secondary Function (PRESS [F/W] + KEY) Selects the desired transmit power output level Tunes the VFO frequency upward in 1 MHz steps Third Function (PRESS & HOLD KEY) Activates the Smart Search feature Starts the scanner upward (toward a higher frequency or a higher channel number) Primary Function (PRESS KEY) Freque
INSTALLATION OF ACCESSORIES ANTENNA INSTALLATION The supplied antenna provides good results over the entire frequency range of the transceiver. However, for enhanced reception on certain non-Amateur frequencies, you may wish to connect an antenna designed specifically for that frequency range, as the supplied antenna is necessarily a compromise outside the Amateur bands, and cannot be expected to provide high performance at all frequencies.
INSTALLATION OF ACCESSORIES BATTERY CHARGING If the battery has never been used, or its charge is depleted, it may be charged by connecting the NC-88/PA-44 Overnight Battery Charger, as shown in the illustration, to the EXT DC jack. If only 12 ~ 16 Volt DC power is available, the optional E-DC-5B DC Adapter (with its cigarette lighter plug) may also be used for charging the battery. A fully-discharged pack will be charged completely in 10 hours.
INSTALLATION OF ACCESSORIES LOW BATTERY INDICATION As your battery discharges during use, the voltage will gradually become lower. When the battery voltage is becoming too low for reliable operation, ” icon will blink on the LCD display, indicating that the “ the battery pack must be recharged before further use. Avoid recharging Ni-MH batteries before the “ ” indicator is observed, as this can degrade the charge capacity of your Ni-MH battery pack.
INTERFACE OF PACKET TNCS The FT-60R/E may be used for Packet operation, using the optional CT-44 microphone adapter (available from your Yaesu dealer) for easy interconnection to commonly-available connectors wired to your TNC. You may also build your own cable, using a fourconductor miniature phone plug, per the diagram below. The audio level from the receiver to the TNC may be adjusted by using the VOL knob, as with voice operation.
OPERATION Hi! I’m R. F. Radio, and I’ll be helping you along as you learn the many features of the FT-60R/E. I know you’re anxious to get on the air, but I encourage you to read the “Operation” section of this manual as thoroughly as possible, so you’ll get the most out of this fantastic new transceiver. Now. . .let’s get operating! SWITCHING POWER ON AND OFF Be sure the Battery Pack is installed, and that the battery is fully charged. Connect the antenna to the top panel Antenna jack.
OPERATION SELECTING THE OPERATING BAND [ ( Press the BAND BAND DN)] key repetitively. You will see the LCD indication move toward a higher frequency band each time you press the [BAND(BAND DN)] key. 850 MHz 144 MHz 250 MHz 350 MHz 430 MHz 850 MHz …… If you wish to move the operating band selection downward (toward a lower frequency band), press the [F/W] key first, then press the [BAND(BAND DN)] key.
OPERATION FREQUENCY NAVIGATION 2) Direct Keypad Frequency Entry The desired operating frequency may be entered directly from the keypad. To enter a frequency from the keypad, just press the numbered digits on the keypad in the proper sequence. Examples: To enter 145.560 MHz, press [1] [4] [5] [5] [6] [0] To enter 145.5625 MHz (in 12.
OPERATION TRANSMISSION Once you have set up an appropriate frequency inside one of the 144 MHz or 430 MHz Amateur bands on which the FT-60R/E can transmit, you’re ready to go on the air! These are the most basic steps; more advanced aspects of transmitter operation will be discussed later. To transmit, press the PTT switch, and speak into the front panel microphone (located in the lower left-hand corner of the speaker grille) in a normal voice level.
ADVANCED OPERATION Now that you’re mastered the basics of FT-60R/E operation, let’s learn more about some of the really neat features. KEYBOARD LOCKING In order to prevent accidental frequency change or inadvertent transmission, various aspects of the FT-60R/E’s DIAL and keypad may be locked out.
ADVANCED OPERATION KEYPAD/LCD ILLUMINATION Your FT-60R/E includes a reddish illumination lamp which aids in nighttime operation. The reddish illumination yields clear viewing of the display in a dark environment, with minimal degradation of your night vision. Three options for activating the lamp are provided: KEY Mode: Illuminates the Keypad/LCD lamp for five seconds when you rotate the DIAL knob or press the keypad or any switch (except PTT switch). This is the factory-programmed default setting.
ADVANCED OPERATION RF SQUELCH A special RF Squelch feature is provided on this radio. This feature allows you to set the squelch so that only signals exceeding a certain S-meter level will open the squelch. To set up the RF squelch circuit for operation, use the following procedure: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 37: RF SQL. 3. Press the [F/W] key momentarily to enable adjustment of this Item. 4.
REPEATER OPERATION Repeater stations, usually located on mountaintops or other high locations, provide a dramatic extension of the communication range for low-powered hand-held or mobile transceivers. The FT-60R/E includes a number of features which make repeater operation simple and enjoyable. REPEATER SHIFTS Your FT-60R/E has been configured, at the factory, for the repeater shifts customary in your country. For the 144 MHz band shift will be 600 kHz; on the 430 MHz band, the shift may be 1.6 MHz, 7.
REPEATER OPERATION MANUAL REPEATER SHIFT ACTIVATION If the ARS feature has been disabled, or if you need to set a repeater shift direction other than that established by the ARS, you may set the direction of the repeater shift manually. To do this: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 38: RPT.MOD. 3. Press the [F/W] key momentarily to enable adjustment of this Item. 4.
REPEATER OPERATION MANUAL REPEATER SHIFT ACTIVATION Checking the Repeater Uplink (Input) Frequency It often is helpful to be able to check the uplink (input) frequency of a repeater, to see if the calling station is within direct (“Simplex”) range. To do this, just press the [HM/RV] key. You’ll notice that the display has shifted to the repeater uplink frequency. Press the [HM/RV] key again to cause operation to revert to normal monitoring of the repeater downlink (output) frequency.
CTCSS/DCS OPERATION CTCSS OPERATION Many repeater systems require that a very-low-frequency audio tone be superimposed on your FM carrier in order to activate the repeater. This helps prevent false activation of the repeater by radar or spurious signals from other transmitters. This tone system, called “CTCSS” (Continuous Tone Coded Squelch System), is included in your FT-60R/E, and is very easy to activate. CTCSS setup involves two actions: setting the Tone Mode and then setting of the Tone Frequency.
CTCSS/DCS OPERATION CTCSS OPERATION 7. When you have made your selection, press the [F/W] key momentarily to save the new settings and exit to normal operation. This is different than the usual method of restoring normal operation, and it applies only to the configuration of the CTCSS/DCS frequencies. Your repeater may or may not re-transmit a CTCSS tone - some systems just use CTCSS to control access to the repeater, but don’t pass it along when transmitting.
CTCSS/DCS OPERATION DCS OPERATION Remember that the DCS is an Encode/Decode system, so your receiver will remain muted until a matching DCS code is received on an incoming transmission. Switch the DCS off when you’re just tuning around the band! TONE SEARCH SCANNING In operating situations where you don’t know the CTCSS or DCS tone being used by another station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used.
CTCSS/DCS OPERATION CTCSS/DCS BELL OPERATION During CTCSS Decode or DCS operation, you may set up the FT-60R/E such that a ringing “bell” sound alerts you to the fact that a call is coming in. Here is the procedure for activating the CTCSS/DCS Bell: 1. Set the transceiver up for CTCSS Decode (“Tone Squelch”) or DCS operation, as described previously. 2. Adjust the operating frequency to the desired channel. 3. Press the [F/W] key, then press the [5(BELL)] key. 4.
CTCSS/DCS OPERATION TONE CALLING (1750 HZ) If the repeaters in your country require a 1750-Hz burst tone for access (typically in Europe), you can set the MONI switch to serve as a “Tone Call” switch instead. To change the configuration of this switch, we again use the Set Mode to help us. 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 26: M/T-CL. 3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item. 4.
MEMORY MODE The FT-60R/E provides a wide variety of memory system resources. These include: 1000 “Standard” memory channels, numbered “000” through “999.” 5 “Home” channels, providing storage and quick recall of one prime frequency on each operating band. 50 sets of band-edge memories, also known as “Programmable Memory Scan” channels, labeled “L01/U01” through “L50/U50.” 10 Memory Banks, labeled “BANK 1” through “BANK10.
MEMORY MODE MEMORY STORAGE 1. Select the desired frequency, while operating in the VFO mode. Be sure to set up any desired CTCSS or DCS tones, as well as any desired repeater offset. The power level may also be set at this time, if you wish to store it. 2. Press and hold in the [F/W] key for one second. 3. Within ten seconds of releasing the [F/W] key, you need to make a decision regarding channel storage.
MEMORY MODE MEMORY RECALL 1. While operating in the VFO mode, press the [V/M(PRI)] key to enter the Memory mode. 2. Rotate the DIAL knob to select the desired channel. 3. To return to the VFO mode, press the [V/M(PRI)] key. When the radio is already set to the Memory mode, an easy way to recall memories is to key in the memory channel number, then press the [F/W] key. For example, to recall memory channel #14, press [1] [4] [F/W].
MEMORY MODE LABELING MEMORIES You may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to aid in recollection of the channel’s use (such as a club name, etc.). This is easily accomplished using the Set Mode. 1. Recall the memory channel on which you wish to append a label. 2. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 3. Rotate the DIAL knob to select Set Mode Item 28: NM WRT. 4.
MEMORY MODE LABELING MEMORIES To disable the alpha-numeric Tag (enabling the frequency display), just repeat the above procedure, rotating the DIAL knob to select “FREQ” in step 5 above. You may set up some memory channels to have their frequencies displayed, while others may be set to have their Name Tag displayed; the selection within Set Mode Item 27 is not applied to all memory channels at once (just the channel on which you currently are operating).
MEMORY MODE DELETING MEMORIES You may desire to delete the memories (except the Memory Channel “1” and Home Channel). The procedure for deleting a channel is quite simple. 1. Press the [V/M(PRI)] key, if needed, to enter the MR mode. 2. Press and hold in the [F/W] key for one second, then rotate the DIAL knob to select the memory channel to be “deleted.” 3. Press the [HM/RV] key momentarily. The display will revert to memory channel #1. The previously-selected memory will be deleted.
MEMORY MODE MEMORY BANK OPERATION The large number of memories available in the FT-60R/E could be difficult to utilize without some means of organizing them. Fortunately, the FT-60R/E includes provision for dividing the memories into as many as ten Memory Groups, so you can categorize the memories in a manner convenient to you. You may enter and exit the “Memory Group” mode by a single press of the [BAND(BAND DN)] key, as we shall see below. Assigning Memories to a Memory Bank 1.
MEMORY MODE MEMORY BANK OPERATION Removing Memories from a Memory Bank 1. Recall the memory channel to be removed from a Memory Bank. 2. Press and hold in the [BAND(BAND DN)] key for one second, then press and hold in the [F/W] key for one second to remove the memory channel data from the Memory Bank. MEMORY ONLY MODE Once memory channel programming has been completed, you may place the radio in a “Memory Only” mode, whereby VFO operation is impossible.
SCANNING The FT-60R/E allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station(s) on that frequency, if you like. Scanning operation is basically the same in each of the above modes. Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal.
SCANNING VFO SCANNING 4. The scanner will then resume according to the Scan-Resume mode selected in the previous section. 5. To cancel scanning, press the PTT switch or [V/M(PRI)] key. Programmed VFO Scan 1. Select the VFO mode by pressing the [V/M(PRI)] key, if necessary. 2. Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL knob to select the bandwidth for the Programmed VFO scanner. Available selections are ±1 MHz, ±2 MHz, ±5 MHz, ALL, PMS-X, and BAND.
SCANNING MEMORY SCANNING Memory scanning is similarly easy to initiate: 1. Select the Memory mode by pressing the [V/M(PRI)] key, if necessary. 2. Press and hold in either the [ (MHz)] or [ (MHz)] key for one second to initiate upward or downward scanning, respectively. 3. If and when the scanner encounters a signal strong enough to open the squelch, the scanner will halt temporarily; the decimal point of the frequency display will blink during this “Pause” condition. 4.
SCANNING MEMORY SCANNING Preferential Memory Scan The FT-60R/E also allows you to set up a “Preferential Scan List” of channels which you can “flag” within the memory system. These channels are designated by a blinking “ ” icon when you have selected them, one by one, for the Preferential Scan List. Here is the procedure for setting up and using the Preferential Scan List: 1. Recall the Memory Channel which you wish to add to the Preferential Scan List. 2.
SCANNING MEMORY SCANNING Memory Bank Scan When the Memory Bank feature is engaged, the scanner sweeps only memory channels in the current Memory Bank. However, if the Memory Bank Link Scan feature is enabled, you may sweep the memory channels in several Memory Banks which you have selected. To enable the Memory Bank Link Scan feature: 1. Set the radio to the Memory mode by pressing the [V/M(PRI)] key, if necessary. 2.
SCANNING WEATHER ALERT SCAN 1) When the Weather Alert Scan feature is engaged, the Scan-Resume mode is fixed to “TIME.” 2) If you are just scanning the Weather Broadcast Channels, the FT-60R/E's receiver will remain muted indefinitely unless the Alert Tone is received. This yields a long period of monitoring time, as no power will be consumed via audio output while scanning for the Alert Tone is in progress.
SCANNING “PRIORITY CHANNEL” SCANNING (DUAL WATCH) The FT-60R/E’s scanning features include a two-channel scanning capability which allows you to operate on a VFO or Memory channel, while periodically checking a userdefined Memory Channel for activity. If a station is received on the Memory Channel which is strong enough to open the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode set via Set Mode Item 35: RESUME. See page 35.
SCANNING “PRIORITY CHANNEL” SCANNING (DUAL WATCH) WX Channel Priority 1. Recall the memory channel you wish to use as the “Priority” frequency. 2. Now, set the radio for operation on a WX channel by pressing and holding in the [1(SQ TYP)] key for one second. 3. Press the [F/W] key, then press the [V/M(PRI)] key to activate the WX Priority mode. The display will remain on the WX channel frequency, but every five seconds the radio will check the Priority Channel (memory channel) for activity. 4.
SCANNING AUTOMATIC LAMP ILLUMINATION ON SCAN STOP The FT-60R/E will automatically illuminate the LCD/Keypad Lamp whenever the scanner stops on a signal; this allows you to see the frequency of the incoming signal better at night. Note that this will, of course, increase the battery consumption, so be sure to switch it off during the day (the default condition for this feature is “ON”). The procedure for disabling the Scan Lamp is: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode.
EPCS (ENHANCED PAGING & CODE SQUELCH) The FT-60R/E includes an Enhanced CTCSS tone encoder/decoder and a dedicated microprocessor providing paging and selective calling feature. This allows you to place a call to a specific station (Paging), and to receive calls of your choice directed only to you (Code Squelch). The paging and code squelch systems use two pairs of (alternately switched) CTCSS tones which are stored in the pager memories.
EPCS (ENHANCED PAGING & CODE SQUELCH) Activating the Enhanced Paging & Code Squelch System 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 29: PAGER. 3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item. 4. Rotate the DIAL knob to select PAG. ON. 5. Press the PTT switch to save the new setting and activate the Enhanced Paging & Code Squelch. 6.
EMERGENCY FEATURE EMERGENCY CHANNEL OPERATION The FT-60R/E includes an “Emergency” feature which may be useful if you have someone monitoring on the same frequency as your transceiver’s UHF “Home” channel. See page 29 for details on setting the Home channel. The “Emergency” feature is activated by pressing and holding in the [4(RPT)] key for one second.
EMERGENCY FEATURE EMERGENCY AUTOMATIC ID (EAI) FEATURE frequency which is stored in Memory Channel “000” for more than five seconds, the radio will automatically transmit a brief (0.5 second) beep tone every 2.5 seconds until the EAI timer expiration at the power level stored in that memory channel; it is NOT necessary for the incapacitated person to press the PTT switch.
SMART SEARCH OPERATION The Smart Search feature allows you to load frequencies automatically according to where activity is encountered by your radio.
INTERNET CONNECTION FEATURE The FT-60R/E can be used to access a “node” (repeater or base station) which is tied into the Yaesu WiRES™ (Wide-Coverage Internet Repeater Enhancement System) network, operating in the “SRG” (Sister Radio Group) mode. Details may be found at the WiRESII Web site: http://www.yaesu.com/en/wiresinfo-en/. This feature may also be used to access other systems, as described below. 1. Press the [0( )SET] key momentarily to activate the Internet Connection feature.
INTERNET CONNECTION FEATURE 2. 3. 4. 5. 6. 7. 8. 9 10. 11. 50 H. Repeat the previous steps until you have completed the access code (“#123”). I. Press and hold in the [F/W] key for one second to save the setting. Press the PTT switch to save the setting and exit to normal operation. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode again. Rotate the DIAL knob to select Set Mode Item 21: I NET. Press the [F/W] key to enable adjustment of this Set Mode Item.
ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM) The ARTS™ feature uses DCS signaling to inform both parties when you and another ARTS™-equipped station are within communications range. This may be particularly useful during Search-and Rescue situations, where is important to stay in contact with other members of your group. Both stations must set up their DCS codes to the same code number, then activate their ARTS™ feature using the command appropriate for their radio. Alert ringers may be activated, if desired.
ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM) ARTS™ constitutes a form of “remote control” operation that may be restricted to certain frequencies. U.S. users should confirm the current status of §97.201(b) of the FCC’s rules governing the Amateur service before utilizing this feature on the 144 MHz band. ARTS™ Polling Time Options The ARTS™ feature may be programmed to poll every 25 seconds (default value) or 15 seconds.
ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM) CW Identifier Setup The ARTS™ feature includes a CW identifier, as discussed previously. Every ten minutes during ARTS™ operation, the radio can be instructed to send “DE (your callsign) K” if this feature is enabled. The callsign field may contain up to 6 characters. Here’s how to program the CW Identifier: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 11: CW WRT. 3.
DTMF OPERATION The FT-60R/E’s 16-button keypad allows easy DTMF dialing for Autopatch, repeater control, or Internet-link access purposes. Besides numerical digits [0] through [9], the keypad includes the [ ] and [#] digits, plus the [A], [B], [C], and [D] tones often used for repeater control. Manual DTMF Tone Generation You can generate DTMF tones during transmission manually. 1. Press the [F/W] key, then press the [9(DTMF)] key to disable the DTMF Autodialer, if necessary.
DTMF OPERATION 12. If you store other numbers, repeat steps 4- 10 above, using a different DTMF memory register. 13. When all required DTMF memories are filled to your satisfaction, press the PTT switch to save the settings and exit to normal operation You may check your work by monitoring the entered DTMF string. To do this, repeat steps 1- 4 above, then press the MONI switch. To send the telephone number: 1. Press the [F/W] key, then press the [9(DTMF)] key to activate the DTMF Autodialer.
MISCELLANEOUS SETTINGS PASSWORD The FT-60R/E provides the password feature which can minimize the chance that your transceiver could be used by an unauthorized party. When the password feature is activated, the radio will ask for the four digit password to be entered when the radio is first turned on. You must enter the four digit password from the keypad. If the wrong password is entered, the microprocessor will shut down the radio automatically. To enter the password , use the following procedure: 1.
MISCELLANEOUS SETTINGS PASSWORD If you forget the password number, you may turn on the transceiver by performing the “All Reset” procedure (see page 64). However, the FT-60R/E will clear the password, as well as all memories, and will restore all other settings to factory defaults. PROGRAMMING THE KEY ASSIGNMENTS Default FT-60R/E Set Mode Items have been assigned (at the factory) to the [7(P1)] and [8(P2)] keys.
MISCELLANEOUS SETTINGS CHANGING THE RECEIVING MODE The FT-60R/E provides for automatic mode changing when the radio is tuned to different operating frequencies. However, should an unusual operating situation arise in which you need to change between the available operating modes (FM and AM), here is the procedure for doing so: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 40: RX MOD. 3.
MISCELLANEOUS SETTINGS RECEIVE BATTERY SAVER SETUP An important feature of the FT-60R/E is its Receive Battery Saver, which “puts the radio to sleep” for a time interval, periodically “waking it up” to check for activity. If somebody is talking on the channel, the FT-60R/E will remain in the “active” mode, then resume its “sleep” cycles. This feature significantly reduces quiescent battery drain, and you may change the amount of “sleep” time between activity checks using the Set Mode: 1.
MISCELLANEOUS SETTINGS DISABLING THE TX/BUSY INDICATOR Further battery conservation may be accomplished by disabling the TX indicator while transmitting and disabling the BUSY indicator while receiving a signal. Use the following procedure: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select Set Mode Item 8: BSY.LED if you wish to disable the BUSY indicator or Set Mode Item 52: TX.LED if you wish to disable the TX indicator. 3.
MISCELLANEOUS SETTINGS TRANSMITTER TIME-OUT TIMER (TOT) The TOT feature provides a safety switch which limits transmission time to a pre-programmed value. This will promote battery conservation by not allowing you to make excessively-long transmissions, and in the event of a stuck PTT switch (perhaps if the radio or a Speaker/Mic is wedged between car seats) it can prevent interference to other users as well as battery depletion.
MISCELLANEOUS SETTINGS MONO BAND OPERATION You may place the radio in a “VHF Only” or “UHF Only” mode which will cause it to function as a 144 MHz or 430 MHz Mono band transceiver. To place the radio into the Mono band operation configuration: 1. Turn the radio off. 2. Press and hold in the MONI switch (just below the PTT switch) while turning the radio on. 3. Rotate the DIAL knob to select the configuration mode menu: F6 V-ONLY: The FT-60R/E will operate on the 144 MHz band only.
MISCELLANEOUS SETTINGS DCS CODE INVERSION The DCS system was first introduced in the commercial LMR (Land Mobile Radio) service, where it is now in widespread use. DCS is sometime referred to by its different proprietary names, such as DPL® (Digital Private Line®, a registered trademark of Motorola, Inc.). DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate of 134.4 bps (bit/sec).
RESET PROCEDURES In the event of erratic operation of the transceiver, it is possible that data on the microprocessor may have become corrupted. While this is a highly unusual situation, the only path to recovery may involve resetting of the microprocessor. Here’s how to do this: 1. Turn the radio off. 2. Press and hold in the MONI switch (just below the PTT switch) while turning the radio on. 3.
CLONING The FT-60R/E includes a convenient “Clone” feature, which allows the memory and configuration data from one transceiver to be transferred to another FT-60R/E. This can be particularly useful when configuring a number of transceivers for a public service operation. Here is the procedure for Cloning one radio’s data to another: 1. Turn both radios off. 2. Connect the optional CT-27 Clone Cable between the MIC/SP jacks of the two radios. 3.
SET (MENU) MODE The FT-60R/E Set Mode, already described in parts of many previous chapters, is easy to activate and set. It may be used for configuration of a wide variety of transceiver parameters, some of which have not been detailed previously. Use the following procedure to activate the Set Mode: 1. Press the [F/W] key, then press the [0( )SET] key to enter the Set mode. 2. Rotate the DIAL knob to select the Set Mode Item to be adjusted. 3.
SET (MENU) MODE SET MODE ITEM FUNCTION 20 [EMG S] Selects the alarm(s) utilized when the Emergency function is engaged. 21 [I NET] 22 [INT CD] Selects the Internet Link Connection mode. Selects the Access Number (DTMF digit) for WIRES™ operation. Selects the memory register for an Access Number (DTMF code) for non-WIRES™ Selects the LCD/Keypad Lamp mode. Selects the Control Locking lockout combination. 23 [INT MR] 24 [LAMP] 25 [LOCK] 26 [M/T-CL] 27 [NAME] 28 [NM WRT] 29 [PAGER] 30 [PAG.ABK] 31 [PAG.
SET (MENU) MODE REPEATER SETTING SET MODE ITEM AVAILABLE VALUES (DEFAULT) Enables/Disables the Automatic Repeater Shift function. Sets the Repeater Shift Direction. Sets the magnitude of the repeater Shift. 4 [ARS] 38 [RPT.MOD] 45 [SHIFT] CTCSS/DSC/DTMF SETTING SET MODE ITEM AVAILABLE VALUES (DEFAULT) Selects the number of CTCSS/DCS Bell ringer repetitions. Setting of the DCS code. Enables/Disables “Inverted” DCS code decoding. Setting of the DTMF Autodialer Delay Time. 7 [BELL] 13 [DCS.COD] 14 [DCS.
SET (MENU) MODE EAI/EPCS SETTING SET MODE ITEM AVAILABLE VALUES (DEFAULT) Enables/Disables the Emergency Automatic ID (EAI) Feature. Enables/disables the Enhanced CTCSS Paging & Code Squelch function. Enables/disables the Answer Back function of the Enhanced CTCSS Paging & Code Squelch. Setting the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch. Setting the Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch.
SET (MENU) MODE Set Mode Item 1 [APO] Function: Setting of the Automatic Power-Off feature. Available Values: OFF/0.5H - 12.0 H in 0.5 hour multiples Default: OFF Set Mode Item 2 [AR BEP] Function: Selects the Beep option during ARTS operation. Available Values: INRANG/ALWAYS/OFF Default: INRANG INRANG: Beeps sound only when the radio first detects that you are within range. ALWAYS: Beeps sound every time a polling transmission is received from the other station (every 15 or 25 seconds when in range).
SET (MENU) MODE Set Mode Item 8 [BSY.LED] Function: Enables/Disables the BUSY LED while the Squelch is open. Available Values: LED. ON/LED.OFF Default: LED. ON Set Mode Item 9 [CLK.SFT] Function: Shifting of the CPU clock frequency. Available Values: SFT.OFF/SFT. ON Default: SFT.OFF This function is only used to move a spurious response “birdie,” should it fall on a desired frequency. Set Mode Item 10 [CWID] Function: Enables/disables the CW identifier during ARTS operation.
SET (MENU) MODE Set Mode Item 17 [DT WRT] Function: Programming of the DTMF Autodialer. See page 54 for details. Set Mode Item 18 [EAI] Function: Enables/Disables the Emergency Automatic ID (EAI) Feature. Available Values: INT. 1M - INT.10M, INT.15M, INT.20M, INT.30M, INT.40M, INT. 50M, CON. 1M - CON.10M, CON.15M, CON.20M, CON.30M, CON.40M, CON. 50M, and OFF Default: OFF Set Mode Item 19 [EDG.BEP] Function: Enables/Disables the Band-edge beeper while selecting the frequency via the DIAL knob.
SET (MENU) MODE Set Mode Item 21 [I NET] Function: Selects the Internet Link Connection mode. Available Values: INT.OFF/INT.COD/INT.MEM Default: INT.OFF INT.OFF: Disables the Internet Link Connection mode. INT.COD: Sets up the Internet Link Connection mode for WiRES™ access. INT.MEM: Sets up the Internet Link Connection mode for other (DTMF string) Internet Link System access. Set Mode Item 22 [INT CD] Function: Selects the Access Number (DTMF digit) for WiRESTM operation.
SET (MENU) MODE Set Mode Item 26 [M/T-CL] Function: Selects the MONI switch (just below the PTT switch) function. Available Values: MONI/T-CALL Default: Depends on the transceiver version MONI: Pressing the MONI switch causes the Noise/Tone Squelch to be over-ridden, allowing you to listen for weak (or non-encoded) signals. T-CALL: Pressing the MONI switch activates a 1750-Hz burst tone, used for repeater access in many countries (especially in Europe).
SET (MENU) MODE Set Mode Item 34 [PSWD W] Function: Stores the password. Available entries are 0-9, A, B, C, D, E (substitute for “ ”), and F (substitute for “#”) Set Mode Item 35 [RESUME] Function: Selects the Scan Resume mode. Available Values: BUSY/HOLD/TIME Default: BUSY BUSY: The scanner will hold until the signal disappears, then will resume when the carrier drops. HOLD: The scanner will stop when a signal is received, and will not restart.
SET (MENU) MODE Set Mode Item 41 [RXSAVE] Function: Selects the Receive-mode Battery Saver interval (“sleep” ratio) Available Values: 200 MS(1:1)/300 MS(1:1.5)/500 MS(1:2.5)/1 S(1:5)/2 S(1:10)/OFF Default: 200 MS Set Mode Item 42 [S SRCH] Function: Selects the Smart Search Sweep mode. Available Values: SINGLE/CONT Default: SINGLE SINGLE: The transceiver sweeps the current band once in each direction, starting on the current frequency.
SET (MENU) MODE Set Mode Item 47 [SPLIT] Function: Enables/Disables split CTCSS/DCS coding. Available Values: SPL.OFF/SPL. ON Default: SPL.OFF When this Set Mode Item is set to “SPL. ON,” you will see the following additional parameters after the “DCS” parameter while configuring Set Mode Item 48: SQL.TYP. D: DCS Encode only. T DCS: Encodes a CTCSS tone and Decodes a DCS code. D TSQL: Encodes a DCS code and Decodes a CTCSS tone. Select the desired operating mode from the selections shown above.
SET (MENU) MODE Set Mode Item 52 [TX.LED] Function: Enables/Disables the TX LED while the radio is transmitting. Available Values: LED. ON/LED.OFF Default: LED. ON Set Mode Item 53 [TXSAVE] Function: Enables/Disables the Transmitter Battery Saver. Available Values: SAV.OFF/ SAV. ON Default: SAV.OFF Set Mode Item 54 [VFO.BND] Function: Enables or disables the VFO band edge limiting for the current band.
SPECIFICATIONS General 108 - 137 MHz (Air Band), 137 - 520 MHz (AM/FM), 700 - 999.990 MHz (FM) TX 144-148 MHz or 144-146 MHz 430-450 MHz or 430-440 MHz Channel Steps: 5/10/12.5/15/20/25/50/100 kHz Frequency Stability: ±5 ppm @ 14 °F to 140 °F (–10 °C to +60 °C) Repeater Shift: ±600 kHz (144 MHz), ±1.6/(5.0)/7.6 MHz (430 MHz) (5.0 MHz: USA) Emission Type: F2D, F3E Antenna Impedance: 50 Ω Supply Voltage: Nominal: 7.2 V DC, Negative Ground (Negative Ground) Operating: 6.0 ~ 16.0 V DC (EXT DC Jack) 11.0 ~ 16.
“AUTO” MODE PRESET OPERATING PARAMETERS USA Version FREQENCY RANGE (MHZ) 108.000 - 137.000 137.000 - 144.000 144.000 - 148.000 148.000 - 156.000 156.000 - 157.450 157.450 - 160.600 160.600 - 160.975 160.975 - 161.500 161.500 - 162.900 162.900 - 174.000 MODE AM FM FM FM FM FM FM FM FM FM STEP 25 kHz 12.5 kHz 5 kHz 12.5 kHz 25 kHz 12.5 kHz 25 kHz 12.5 kHz 25 kHz 12.5 kHz FREQENCY RANGE (MHZ) 174.000 - 222.000 222.000 - 225.000 225.000 - 300.000 300.000 - 336.000 336.000 - 420.000 420.000 - 450.000 450.
Declaration of Conformity We, Yaesu UK Ltd. declare under our sole responsibility that the following equipment complies with the essential requirements of the Directive 1999/5/EC. Type of Equipment: Brand Name: Model Number: Manufacturer: Address of Manufacturer: Dual Band Transceiver YAESU FT-60E Vertex Standard Co., Ltd.
Copyright 2012 YAESU MUSEN CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD.
