Operating Manual

ManualsBrandsYaesu Musen ManualsElectronicsULTRA LOW POWER WIFI MODULE

SCU-30

Wireless Access Point

The SCU-30 is wireless access point supplied with 5 feet of cable that plugs into your compatible Stan-

dard Horizon VHF radio to wireless connect with the SSM-71H Wireless Remote Access Microphone

RAM4W. Please refer to the STANDARD HORIZON products catalog or web site for compatibility.

Owner’s Manual

The details of the installation and operation of the SCU-30 are included in the owner’s manual of

the compatible xed mount radio, or can be downloaded at www.standardhorizon.com.

Supplied Accessories

Antenna Unit (5 feet cable) .................................................................................................................... 1

Antenna Base (Socket, Part number: RA6054200) .............................................................................. 1

Screws (M3X8 SUS, Part number: U20308020) .................................................................................. 3

Installing

The SCU-30 is designed to be mounted on a base, installed on an extension pole or ush mounted.

Choose a location for the antenna unit that has not located within 3 feet of radar or other transmitting

antenna. Ensure there are no major obstructions or xtures in the immediate proximity to the anten-

na unit. If you are unsure of the location, temporarily mount the antenna to verify correct operation. If

mounted close to a radar, turn on the radar and check the to verify correct operation.

Compass Safe Distance

This antenna unit at least 0.2m (0.66 feet) from magnet-

ic compass.

Base Mounting the antenna

The thread used on the base of antenna (1 inch, 14 TPI)

is an industry standard used on a wide range of commer-

cially available mounting brackets or extension poles.

Due to the manufacturing process of the mounting brack-

ets, the antenna may not tighten all the way down onto all

the threads. This is of no concern however as the anten-

na must be tightened until the antenna stops rotating.

1. When passing the antenna cable through a mounting

bracket or extension pole, make sure to pass the ca-

ble through the antenna base.

NOTES:

・

When routing the antenna cable along the outside of

the extension pole, pass the cable through the groove

as shown by the dotted lines in the gure on the right.

(Please cut the blank panel with a long-nose pliers.)

・

The antenna cable can be cut and spliced to ease installation. Care must be taken when reconnecting

the antenna cable to protect from water and corrosion.

2. Mount the antenna base to the antenna using the supplied three screws.

3. Screw the antenna base to the mounting bracket or extension pole.

4. Install the mounting bracket or extension pole.

Flush Mounting the antenna

NOTE: Before drilling the mounting holes, it is

recommended to verify correct opera-

tion in the desired location.

1. To ease installation use the supplied flush

mount template.

2. Apply the ush mounting template sticker.

3. Drill the 0.78” (20 mm) and 0.13” (3.2 mm)

holes, and remove the template.

4. Insert the cable into the 0.78” (20 mm) hole

and route to the transceiver.

5. Apply a small amount or RTV to the under-

side of the antenna.

6. Place the antenna and screw into place us-

ing the supplied screws.

Template

Use this template to mark the

location where the hole for

the ush mount is to be cut.

cut here

TEMPLATE for the SCU-30

Antenna Base

Pole

Antenna Cable

Antenna Unit

φ3.2 mm [0.13 inch]

φ20 mm [0.78 inch] or greater

φ3.2 mm [0.13 inch]

Safety Precautions (Be Sure to Read)

Be sure to read the safety precautions of Operating Manual of the compatible xed mount VHF

radio to use this product safely.

Summary of content (4 pages)

PAGE 1
・The antenna cable can be cut and spliced to ease installation. Care must be taken when reconnecting the antenna cable to protect from water and corrosion. 2. Mount the antenna base to the antenna using the supplied three screws. 3. Screw the antenna base to the mounting bracket or extension pole. 4. Install the mounting bracket or extension pole.
PAGE 2
Dimensions Yaesu Musen Co. Ltd is responsible for ensuring that the end-user has no manual instructions to remove or install module. 85 mm 60 mm The Wireless Networking Module is limited to SCU-30 installation ONLY. This equipment is defined as a transmitting device designed to be used in other than fixed locations. In this context, the term “fixed location” means that the device is physically secured at one location and is not able to be easily moved to another location.
PAGE 3
Statements and Requirements This module has been approved as single modular approval. The module is limited to installation in mobile or fixed applications according to FCC Rules Part 2.1091(b). Separate approval is required for all other operating configurations, including portable configurations with respect to FCC Rules Part 2.1093 and different antenna configurations. The frequency range of the module is 2412 to 2462 MHz. The radiated RF power output of the module is 0.095 Watts.
PAGE 4
The user manual for the host must contain the following regulatory wording. The wording below satisfies both the FCC and ISED Canada requirements. This device complies with part 15 of the FCC and Canadian Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.