User's Manual

ManualsBrandsY Soft ManualsElectronicsExternal reader module ASK FSK

Table Of Contents

CONFIDENTIAL

making the MFDs think™

Network Card Reader

October 13, 2014

Summary of content (11 pages)

PAGE 1
making the MFDs think™ Network Card Reader October 13, 2014 CONFIDENTIAL
PAGE 2
October 13, 2014 TABLE OF CONTENTS 1 FCC statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Network Card Reader overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.
PAGE 3
October 13, 2014 DOCUMENT DESCRIPTION At a Glance FCC statements Network Card Reader overview System Overview Ethernet Reader specification Terminal's configuration SafeQ server configuration Ethernet Reader Service procedures Service procedures Service firmware Reader firmware Network Card Reader CONFIDENTIAL 3
PAGE 4
October 13, 2014 1 FCC STATEMENTS § 15.21 Information to user The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 5
October 13, 2014 2 NETWORK CARD READER OVERVIEW The YSoft SafeQ ® Ethernet Reader is based on YSoft SafeQ® Terminal UltraLight. YSoft SafeQ® Ethernet Reader provides compact, fast and simple user interface for authorization to printer. It has no display available; therefore user interaction is limited to status leds. User authentication (on Ethernet Reader) is possible only with card.
PAGE 6
October 13, 2014 2.1 SYSTEM OVERVIEW The purpose of Ethernet Reader is to handle user authentication and authorization to the device using card. User can use also the PIN authorization (using the MFD integrated panel). Only selected card readers are supported by Ethernet Reader. The Ethernet Reader is equipped with a 2-ports network switch and so it is not necessary to provide another Ethernet socket for connection - the copier or printer can be connected via the terminal.
PAGE 7
October 13, 2014 2.2 ETHERNET READER SPECIFICATION Parameter Value Identification Using a card reader Network 2-port 10/100 Mbit switch (auto MDI/MDIX) Processor Freescale Coldfire v2 Memory 64kB RAM, 512kB Flash Electric power supply input 12V DC Maximum current input 1.
PAGE 8
October 13, 2014 3 TERMINAL'S CONFIGURATION Ethernet Reader requires TCP/IP connection to the YSoft SafeQ server. Ethernet Reader has own IP and MAC address. For the proper network configuration you can use: SafeQ Terminal Configuration utility (terminal config) or Configuration utility for hardware terminals (termtool) There is a default network configuration used for Ethernet Reader: DHCP=0 IP=192.168.0.100 NETMASK=255.255.255.0 GATEWAY=192.168.0.254 DNS=192.168.0.254 SERVERIP=192.168.0.
PAGE 9
October 13, 2014 4 SAFEQ SERVER CONFIGURATION After the Ethernet Reader is properly configured, it must be connected to the YSoft SafeQ®. Assume that the YSoft SafeQ® server and YSoft SafeQ® Terminal Server are already installed and running. 1 Log in to the SafeQ Web administration with sufficient rights to manage devices. 2 Go to Devices > Printers selection and click the edit icon next to the device or double click on the device.
PAGE 10
October 13, 2014 3 Go to Terminal tab and insert Network Card reader serial number. This serial number equals to serial number written in SafeQ Terminal Configuration util (first column). Then press Reinstall button to apply new settings. NOTE: If you want to add Network Card reader serial number, one of the authentication method with card must be selected. 4 Since the installation is successfully finished, the Ethernet reader is successfully configured.
PAGE 11
October 13, 2014 5 ETHERNET READER SERVICE PROCEDURES 5.1 SERVICE PROCEDURES For more info about all service procedures, please visit: Performing service procedures of Terminal UltraLight and Network Card Reader 5.2 SERVICE FIRMWARE Service firmware is the most important part of the reader firmware. Right after power-up it will check the emergency button if any action is required. Then it will check the normal firmware for integrity.