ENG ENG Product name: 3D Printer Product Manual P.2-P.4 Advanced Maintenance Tools P.5 Print Bed adjustment P.6 Service Code Informations P.
ENG Product Manual Filament Slot Speaker Display Panel Remove the packaging supports Extruder Module Z-Axis LAN Port USB Port Front Door Print Bed Power Switch Remove the print bed fixing screws and printing module fixers Power Connector Overview This guide provides details on how to start off your da Vinci 2.1 Duo Plus 3D printer correctly. Please read the instructions before starting to print.
ENG Product Manual Open the box PRINT ING GLUE STIC K 1 Open the box and remove the accessories and the cushion. 2 Take out the printer by holding the grip holds. 3 Remove plastic bag and tapes. Packing supports x2 Cable tie x1 Tapes x2 4 Open the top door, then remove packaging supports and tapes. 6 Remove the tapes and cardboard. 5 Remove the print bed fixing tapes and cushion. 7 Remove the screw and plastic piece under print bed. A B 8 Remove the drip tray fixing tapes.
ENG Product Manual Install Cartridge 1 Remove the filament stopper. 2 Install new filament cartridge into the empty slot. 3 Place and push to fix the cartridge locker to the slot. 4 Select "Filament" > "Cartridge 1" > "Load". Do Not Touch. Cartridge 1 Guide Hole 1 Guide Hole 1 Do Not Touch. Guide Hole 2 Guide Hole 2 Cartridge 2 5 Insert filament into the guide hole until the printer starts to load filament.
ENG Product Manual Sample Print Apply glue to print bed before printing. Glued area depends on the flat measurement or object to be printed. 1 Select "Print" > "Sample" on the screen. PRINTING 2 Select a sample to print, and tap "Print". 3 After the printing is completed and the print bed became cool, use a scraper to take out the object. 4 Finally use a damp cloth to clean the print bed.
Product Manual & Maintenance Tools ENG Unload filament Note: Please always complete the procedure for "FILAMENT UNLOADING" before changing a new cartridge. Never cut off the filament from the extruder to prevent extruders from clogged. 1 Select "Filament" > "Cartridge1" (or "Cartridge 2") > "Uninstall" on the screen. 2 Filament is unloaded from extruder automatically. Pull filament out from the guide hole when prompted. 3 When filament is pulled out, press "OK".
ENG Maintenance Tools Specifications Feature da Vinci 2.1 Duo Plus 3D Printer Print Technology Fused Filament Fabrication(FFF) Print Head Dual Head Build Volume (W x D x H) 15 x 20 x 20 cm Layer Resolution Setting Standard Speed Ultra fast Custom Filament Diameter 1.75 mm Nozzle Diameter 0.4 mm AC Input 100-240V, 50~60Hz Connectivity USB 2.0 x1 WiFi LAN USB Flash Driver Display Touch Panel Indicator Speaker Indicator Buzzer Lighting LED Weight 28.
Print Bed Adjustment Instructions ENG This print bed has been calibrated by our professional technician before shipment. Do not adjust the platform yourself unless necessary, or contact our Technical Consulting:0809-016-225 To clean the molted filament from nozzle thoroughly, it is recommended to activate “UNLOAD FILAMENT” function to keep heating the extruder for better cleaning.
Print Bed Adjustment Instructions ; < = Location of the PHDVXUHPHQW SRLQWV & 4 Refer to the values for adjustment % $ Adjust the location of the screws ENG I. Adjust the screw at Point A to reduce the difference between the 1st and the 2nd measurements. II.Adjust the screw at Point B based on your evaluation of the results obtained from the previous steps.
Print Bed Adjustment Instructions ENG )RU IXUWKHU LQIRUPDWLRQ DQG LQVWUXFWLRQ RI WKH VHUYLFH FRGH SOHDVH UHIHU WR ;<=SULQWLQJ ZHEVLWH KWWS VXSSRUW [\]SULQWLQJ FRP RU FRQWDFW VHUYLFH FHQWHU IRU KHOS Service Code Display Panel Description 炵 炵 炵 Extruder or heated bed higher/lower than maximum/minimum temperature during printing 炵 炵 炵 Extruder cannot heat to the specified temperature 炵 炵 炵 Print bed heating error; critical temperature detected 炵 炵 炵 炵 Extruder(s) heating error; critic
Print Bed Adjustment Instructions ENG )RU IXUWKHU LQIRUPDWLRQ DQG LQVWUXFWLRQ RI WKH VHUYLFH FRGH SOHDVH UHIHU WR ;<=SULQWLQJ ZHEVLWH FCC Statement KWWS VXSSRUW [\]SULQWLQJ FRP RU FRQWDFW VHUYLFH FHQWHU IRU KHOS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.