1. what’s in the box Video Doorbell Wall Mount Bracket Indoor Wireless Chime List Tools USB Charging Cable Extension Wire & Wire Nuts (Optional) Jumper for Original Indoor Chime (Optional) User Guide 2.
3. Meet the chime Button Function Explaination: Click to select ringtone Click to set volume: level 1: 110 dB level 2: 100 dB level 3: 90 dB level 4: 80 dB Click: Enter/Quit pairing mode Ringtone Selection Volume Control Setting (Pair/ Reset) Red LED Indicator Blue LED Indicator Battery Compartment Micro USB Power Port AA Battery × 3 Press & hold for 5 sec: Restore factory defaults 4. SET up your doorbell 1 Turn on the doorbell by the on/off switch on the rear of the doorbell.
4 Start the Wi-Fi configuration following the in-App instructions or referring to below tutorial steps.
5 LED indicator explanation: Solid Red Device is abnormal. Solid Blue Successfully connected to WiFi network. Flashing Red Slowly Ready for WiFi configuration. Flashing Blue Quickly Firmware is upgrading. Flashing Red Quickly Device is connecting to WiFi. Nothing Stand by mode/ Power off. 5. Live view Tap on the Home page devices to watch live view from your doorbell.
6. Settings Back to live view Power saving settings Receive/block alert notifications Recording management Edit device name 2 Motion detection settings Share device with other users Cloud storage setting Device information Device version Installation guide Delete the device Basic function: 7. Recording If the Micro-SD card is properly installed, you can playback the video clips taken after motion events or visitor calls. (Live viewing will not trigger device recording).
. History Playback Tap ‘History’ to play the video clips recorded in the MicroSD card.
. Connect the chime 1 Supply power to the chime The chime can be powered by 3 units of AA batteries(Provided) or a DC5V⎓1A power adapter. (not included) Powered by AA batteries Powered by DC5V Adapter and Micro USB Cable 3 Press the doorbell button 2 Click reset button Reset Button Red LED Flashing Blue LED Flashes Click on RESET only once, and you will see the chime indicator flashing red, indicating that the chime is in pairing mode.
NOTE: 1. Your doorbell communicates with the chime via Radio Frequency, but not WiFi. 2. You can assign different chimes as needed. 3. Press and hold RESET button on the chime for 5 seconds till the red indicator flashes 3 times, so as to release the connection between the chime and its connected doorbell. 10. Installation Your doorbell comes with a 10,000mAh battery pack built-in, and it also works with existing 12V~24V AC hardwire power source.
Select a location for your video doorbell. Determine the mounting position of the doorbell. Check if you can reuse the existing holes on the wall. If not drill new holes to mount your video doorbell. It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance. 4 feet 120cm 4 Replace your existing doorbell. A Remove the existing doorbell from the wall and disconnect the wires.
Wall mount screw kit C The cable order doesn’t matter. Mount the bracket on the wall with provided screw set or adhesive tape. D Attach the wires to the terminals. Wire extension kits are optional. Security Screw Screwdriver E Feed the wires back to the wall and mount the doorbell to the brackets. F Tighten the security screw at the bottom of the bracket. 5 Restore power at the breaker, and your doorbell is ready for use.
10.2 Wireless installation Wall mount screw kit A Release the bracket from the doorbell with the provided tool. C Adhesive tape is provided to mount the bracket on flat surfaces.(Optional) - 11 - B Mark the screw holes and mount the bracket on your wall with screws. D Attach the doorbell to the fixed mounting bracket.
Security Screw Screwdriver E Tighten the security screw at the bottom of the bracket. F All set! Press the doorbell button to run a test. 11. Trouble Shooting Q1: Is the video doorbell powered by battery? A1: Yes, there is a 10,000mAh big Li-ion battery pack built-in. Thanks to the low power consumption technology, a full charge lasts for more than 3 months in our lab test environment.
Q5: I installed my video doorbell, but the video or audio quality is poor, why? A5: In live view interface, WiFi status will be listed. It is suggested to ensure the Wi-Fi status be more than 70%, so as to get your doorbell work as expected. If you think your problem is caused by low Wi-Fi signal strength, try moving your Wi-Fi router closer, or add one Wi-Fi Booster to extend your Wi-Fi range. Q6: Does the video doorbell work with existing indoor mechanical chime? A6: No.