USER MANUAL V200 Wireless Diagnostics Module Shenzhen Xtooltech Intelligent Co.
Please read this user manual carefully before using the V200. When reading the manual, please pay attention to the words “Note” or “Caution” and read them carefully for appropriate operation. Trademarks is a registered trademark of Shenzhen Xtooltech Intelligent CO., LTD.
This manual is designed for the usage of the V200 and provides operating instructions and product descriptions for users of the V200. No part of this manual can be reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the prior written permission of Xtool. Use the device only as described in this manual.
The exhaust gas of the vehicle contains harmful chemicals, please ensure adequate ventilation. Do not touch the cooling system components or exhaust manifolds when the engine is running due to the high temperatures reached. Make sure the car is securely parked, Neutral is selected or the selector is at P or N position to prevent the vehicle from moving when the engine starts.
E-Mail: supporting@xtooltech.com Tel: +86 755 21670995 or +86 755 86267858 (China) Official Website: www.xtooltech.com Please provide your device serial number, VIN code, vehicle model, software version, and other details when seeking technical support. If there are screenshots or videos, it will better help us locate your problem.
Content 1 GENERAL INTRODUCTION ......................................................... 6 Front/Back View of VCI BOX ................................................................................................ 6 Top/Bottom View of VCI BOX ............................................................................................... 6 2 TECHNICAL SPECIFICATIONS .......................................................................... 7 4 DIAGNOSIS ....................................................
1 GENERAL INTRODUCTION FRONT/BACK VIEW OF VCI BOX ① ② Front Back ① Display Screen: Show status of the V200 like battery voltage, Bluetooth connection, and car communication status. ② Nameplate: Show basic information about the V200, like the serial number. Make sure that you’re using the V200 that is paired with the tablet, or it will not communicate. The serial number of the VCI box must be the same as the serial number of the tablet.
① DB15 Port: Used to connect the V200 to the OBDII port on the vehicle. ② USB-B Port: Used to connect the V200 to the tablet. 2 TECHNICAL SPECIFICATIONS Specification Item Display Connectivity Ports Description 1.54-inch, 128×64 resolution USB Bluetooth USB type-B DB15 Input Voltage 12V DC Operating Temperature -10~50℃ Relative Humidity < 90% Dimensions 91.0×157.0×35.0(mm) 3 DIAGNOSIS The V200 connect to the vehicle through the main test cable.
VEHICLE CONNECTION The V200 should establish communication with the vehicle, and Bluetooth should be connected between the tablet and the V200. Please follow the steps below. Fig 4-1 1. Turn on the tablet. 2. Connect the vehicle, the V200 and the tablet following the diagram below. Usually, the OBD port is located under the dashboard, inside driver’s footwell. 3. Wait for the VCI box to communicate with the tablet, then click into the menus to perform the functions.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
SHENZHEN XTOOLTECH INTELLIGENT CO., LTD Company address: 17&18/F, Building A2, Creativity City, Liuxian Avenue, Nanshan District, Shenzhen, China Factory address: 2/F, Building 12, Tangtou Third Industrial Zone, Shiyan Street, Baoan District, Shenzhen, China Service-Hotline: 0086-755-21670995/86267858 Email: marketing@xtooltech.com supporting@xtooltech.com Fax: 0755-83461644 Website: www.Xtooltech.