Quick Start Guide

Quick start guide
Star machine
Due to product updates, some details of this
document may not match the product, please
prevail in kind! The manufacturer has the right
to modify the content of this document without
prior notice!
Service Information
Customer service line: 0756-2897617
Official website: www.starpany.cn
Manufacturer: Zhuhai yike intelligent technology co., ltd.
Manufacturer Address: 307-2, Zhonglixing Building,
No. 4 Xingguo Street, Xiangzhou District, Zhuhai
Printer cleaning
The printer should be cleaned in a timely manner when
the printer:
1, The printing is not clear;
2, The printed page is not clear in the vertical direction;
The cleaning steps for the print head are as follows:
1. Turn off the printer power, open the top cover, and
remove the paper if there is paper;
2. If you have just finished printing, you should wait for the
print head to cool completely.
3. Use a soft cotton cloth and absolute ethanol (should be
wrung out) to wipe off the dust and stain on the surface of
the thermal head of the print head;
4. After waiting for the absolute evaporation of absolute
ethanol, close the upper cover and re-test the machine to
print;
Statement
This product is a Class A product and may cause radio
interference in a living environment. In this case, the
customer may be required to take practical measures to
interfere with it.
Precautions for use
Do not immerse the printer in water or expose it to rain,
otherwise the printer may be damaged.
Do not open the paper compartment cover during printing,
as this may cause the printer to malfunction.
When printing using Bluetooth, the distance during
printingcannot exceed 10 meters, otherwise it may
cause garbled printing or unprintable.
Although the printer can operate stably from 0 ° C to
45 ° C, excessive ambient temperature (45 ° C) or too
low ambienttemperature (0 ° C) can result in reduced
print quality.
Using poor quality paper or paper that has been stored
fortoo long may result in reduced print quality or even
damage to the printer.
The printer tries to use up and recharge the battery before
charging, which can effectively guarantee the battery life.
Caveat
This product has a built-in lithium battery, do not use it in
an environment where the temperature is higher than
45 °C, do not place it near open flames or other heat
sources, do not place it in hot sunlight, otherwise it may
cause an explosion or fire hazard.
Do not disassemble and replace the battery, if you replace
the battery, you must use the same size battery, otherwise
there is a danger of explosion.
Used batteries are recycled or disposed of when in
accordance with local regulations and product instruction
manuals.
Note that the thermal head of the print head is a hot
component. It is strictly forbidden to touch the thermal
sensorpart during printing or at the end of printing!
Note that the paper exit tearing blade is sharp, please
be careful not to touch!
FCC Statement
Any Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
The device has been evaluated to meet general RF
exposure requirement.
The device can be used in portable exposure condition
without restriction.