Contact Information Motion Computing 8601 RR2222 Building II Austin, TX 78730
THIS MANUAL COVERS THE FOLLOWING VARIATIONS: 1. RDA-100 (version B: Base) - Base product without radios used as a charging and power system for peripherals (i.e. IR camera). 2. RDA-100 (version WM: Wi-Fi, Mesh) - Base product with two radios, this version of the product can be used to provide access to the WAN via Ethernet port connectivity and client connectivity via Wi-Fi. 3. 4.
CONTENTS 4. Symbol Legend 5. Safety Information 6. Introduction 7. Overview of AC/DC Inputs and System Controls 8. Operation – Start Up 9. Operation - Shutdown 10. Trouble Shooting 11. Input Specifications 12. RDA-100 Specifications 13.
SYMBOL LEGEND GENERAL WARNING DC Current AC Current
SAFETY INFORMATION SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS This Manual gives step –by-step instructions for the setup and operation of the RDA-100. There is a potential risk of fire, electric shock or injury to person or persons if this product is not used as instructed. WARNING: When using the RDA-100, use basic precautions including the following: • Read the entire user manual before turning on or connecting to power. • Do not power up unit in wet area, electric shock may occur.
INTRODUCTION The RDA-100 is a stand-alone, battery powered, self contained mobile access point. This unit can be plugged in as a wall unit, run off of the internal battery, powered by a solar array or a combination of all three. The RDA-100 can be accessed wirelessly as a stand-alone unit or used in a mesh with other wireless devices. This unit can also be used as a modular device that can be coupled with other Motion Computing Accessories. These Accessories are sold separately at http://www.
Overview of AC/DC Inputs and System Controls 1 2 1 +12VDC Auxiliary Power Output Available to power peripherals 2 Solar Power Input 3 3 110V AC Power Input 4 RJ45 Connection POE POE Connects to Radio Input 5 System Key Switch Full power over ride and lock-out 6 On/Off Switch 7 12VDC Power Indicator Indicates AC input or battery mode 4 5 6 7
OPERATION To initiate the RDA-100, first refer to safety precautions on page 4. • 1. Plug unit in to a standard three prong 110v power cord (MUST HAVE GROUND TERMINAL). • 2. Insert key into the system key switch (Item# 5) and turn the key clockwise. • 3. Turn the green on/off switch (Item# 6) clockwise to arm system (switch will illuminate green if plugged into 110v power outlet). • 4. The Red 12v power light (Item# 7) will then illuminate indicating that the system is on. • 5.
OPERATION SHUTTTING DOWN THE RDA-100 • 1. Turn the green switch (Item# 6) counter-clockwise and verify that the red 12v indicator light (Item# 7) goes off. • 2. Turn the system key switch (Item# 5) counter-clockwise and verify that both the green light and red light are no longer illuminated. If so, remove key. • 3. Unplug the unit and secure weather caps (Items 1,2 and 3). Note: Before moving unit make sure that all peripheral accessories are unplugged from the RDA-100.
TROUBLE SHOOTING TROUBLE SHOOTING THE RDA-100 The RDA-100 will not power up. • Make sure that the unit is plugged in to a live power source, and check to see that both the System key Switch and the green on/off switch are turned to the clockwise on position. If the RDA-100 still will not power up; the battery is low and must be charged before the unit can be used. Cannot connect to the RDA-100 • Make sure that you have selected the SSID labeled motion and entered the proper credentials.
Technical Specification and Ranges of Input Sources A. Solar Panel: 18-36 Volt Direct Current , 8 Amp Maximum B. POE (Power Over Ethernet): 18-57 Volt Direct Current 2.6 Amp Maximum C. AC Power: 110-240 Volt Alternating Current , 60/50Hertz,1.5 Amp Maximum Technical Specification and Ranges of Output Sources A. Solar Panel: 12 Volt ,1.5 Amp as Battery Voltage, 12.5 Volt Maximum B. POE (Power Over Ethernet): 12 Volt ,1.0 Amp, 12.
Specifications of Dimensions and Weight • • • • Length = 11.875” Width = 10.50” Height = 11.
NOTE: There are no user serviceable parts in the unit. Opening the unit voids the product warranty. The unit is not to be opened except by a Motion Computing trained service technician.
